TRENDnet Network Card TEW 630APB User Manual

Quick Installation Guide  
TEW-630APB  
 
1. Before You Start  
Package Contents  
?TEW-630APB  
?Quick Installation Guide  
?User's Guide CD-ROM  
?AC Power Adapter (12V DC, 1A)  
?1 x RJ-45 Ethernet  
Installation Requirements  
?A web browser such as Internet Explorer (5.5 or higher)  
?A computer with a network adapter properly installed  
?A network Switch or Hub with an available network LAN port  
?A RJ-45 network cable  
Application  
300Mbps Wireless N  
Access Point  
(TEW-630APB)  
HD  
DATA  
300Mbps, share multimedia throughout the house  
1
 
English  
2. Install Hardware  
Note: Locate an optimum location for the Access Point. The best place for the  
Access Point is usually at the center of your wireless network. Please connect  
the computer configuring the TEW-630APB to the same switch/hub.  
1. Connect a RJ-45 cable from the  
Switch/Hub to the LAN port of the  
Access Point.  
2. Connect the AC Power Adapter to  
the Access Point and then to a  
power outlet.  
3. Verify that the following front panel  
lights are on: Power, LAN and  
WLAN.  
2
 
English  
3. Configure the Access Point  
Note: It is recommended that you configure the Access Point from a wired  
computer. Before the Access Point can be configured, a Static IP address  
must be assigned to your computer's network adapter in the subnet of  
192.168.1.x. Since the Access Point's default IP address is 192.168.1.100,  
make sure no other network devices are assigned an IP address of  
192.168.1.1. (Refer to the Troubleshooting section on how to configure TCP/IP  
settings on your PC)  
1. Open your web browser, type  
Address bar, and press Enter.  
2. Enter User name and Password,  
and then click Log in.  
User name: admin  
By default, there is no password.  
3. Click Launch Wireless Setup  
Wizard.  
4. Click Next.  
3
 
English  
5. Click Next.  
Note: The example below is for WPA security. If you select Best (WPA2) or  
Better (WPA), make sure your wireless adapters support WPA2 or WPA. If  
your wireless adapters do not support WPA2 or WPA, then select Good (WEP).  
6. Select the desired level of security  
and then click Next.  
7. If you have enabled security, type  
in any password and then click  
Next.  
4
 
English  
8. Take note of the Pre-Shared Key  
and then click Save.  
9. Click Continue.  
Note: If you enabled any level of security (Best, Better, Good), you need to  
make sure to enter the Pre-Shared key in your wireless adapter's configuration.  
Your installation is now complete.  
For detailed information regarding the TEW-630APB's configuration and  
advanced settings, please refer to the Troubleshooting section, User's Guide  
Register Your Product  
To ensure the highest level of customer service and support, please take a moment to  
register your product Online at: www.TRENDnet.com/register  
Thank you for choosing TRENDnet  
5
 
English  
Troubleshooting  
Q1: How do I configure TCP/IP settings on my computer?  
1. Go into the Control Panel and double-  
click the Network Connections icon,  
right-click the Local Area Connection  
icon and then click Properties.  
2. Click Internet Protocol (TCP/IP) and  
then click Properties. Then click on  
Use the following IP address, and  
make sure you assign your network  
adapter an IP address in the subnet of  
192.168.1.x.  
error message says "The page cannot be displayed". How can I get into the  
TEW-630APB's web configuration page?  
A2: First, check your hardware settings again by following the instructions in  
section 2. Second, make sure the LAN and WLAN lights are lit. Third, make sure  
the TCP/IP settings are configured properly (see Q1). Fourth, since the Access  
Point's default IP address is 192.168.1.1, make sure that no other network  
devices are assigned an IP address of 192.168.1.1.  
Q3: If my network's IP is different than the Access Point's range, what should I  
do?  
A3: You should still configure the Access Point first. After all the settings are  
applied, go to the Access Point's configuration page, click Basic -> Network  
Settings, change the IP address of the Access Point to match your network's IP  
and save the settings.  
6
 
Q4: After I successfully configured the Access Point to meet my network settings,  
I can not connect to my network using wireless computers.  
A4: If you have a DHCP server in your network, you need to go into TCP/IP  
settings again and re-select "Obtain an IP address automatically" to allow the PC  
to regain an IP address from your DHCP server.  
Q5: All the settings are correct, but I can not make a wireless connection to the  
Access Point.  
A5: First, double check that the WLAN light on the Access Point is lit. Second,  
power cycle the Access Point. Unplug the power to the Access Point. Wait 15  
seconds, then plug the power back in. Third, contact the manufacturer of your  
wireless network adapter. Make sure the wireless network adapter is configured  
with the proper SSID. The default SSID of the Access Point is TRENDnet. If you  
have enabled any encryption on the Access Point, make sure to configure the  
wireless network adapter with the same Pre-shared key.  
If you still encounter problems or have any questions regarding the TEW-630APB,  
please contact TRENDnet's Technical Support Department.  
7
 
Certifications  
This equipment has been tested and found to comply with FCC and CE Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received. Including interference that may  
cause undesired operation.  
Waste electrical and electronic products must not  
be disposed of with household waste. Please  
recycle where facilities exist. Check with you Local  
Authority or Retailer for recycling advice.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV  
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS  
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO  
OPERATE THE EQUIPMENT.  
ADVERTENCIA  
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de  
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al  
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador  
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria  
existente en el pais o zona de instalación.  
 
TRENDnet Technical Support  
.
US Canada  
Toll Free Telephone: 1(866) 845-3673  
24/7 Tech Support  
.
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)  
Toll Free Telephone: +00800 60 76 76 67  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Worldwide  
Telephone: +(31) (0) 20 504 05 35  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Product Warranty Registration  
Please take a moment to register your product online.  
20675 Manhattan Place  
Torrance, CA 90501  
USA  
 
Copyright ©2007. All Rights Reserved. TRENDnet.  

Toshiba Computer Drive XM 7002B User Manual
Toshiba Scanner 501 User Manual
Tripp Lite TV Cables A102 02M User Manual
Uniden Telephone TRU 3465 User Manual
VDO Dayton Car Video System DV 6100 User Manual
Vector Power Supply VEC018 User Manual
ViewSonic Car Video System VA903m User Manual
Vinotemp Refrigerator WM 15SFCW User Manual
VTech Cordless Telephone 6031 User Manual
Weed Eater Lawn Mower 96022000902 User Manual