TP Link Digital Camera MC200CM User Manual
User Guide  
MC200CM  
MC210CS  
MC220L  
Gigabit Ethernet Media Converter  
 
CONTENTS  
Package Contents...........................................................................1  
1. Introduction.............................................................................1  
2. Features...................................................................................2  
3. Appearance Indication...........................................................3  
3.1 LED Indicators................................................................. 3  
3.2 Switch.............................................................................. 4  
4. Installation Guides .................................................................5  
4.1 Gigabit Ethernet Media Converter:.................................. 5  
4.2 Configuration................................................................... 7  
4.3 Installation Procedure...................................................... 8  
4.4 Install Media Converter into MC1400.............................. 9  
5. Troubleshooting ...................................................................10  
6. Appendix: Specifications.....................................................11  
i
 
Package Contents  
Before starting using the products, make sure what you have is what you  
ordered. The Converter includes:  
¾
¾
¾
One Converter  
One AC-DC Power Adapter (DC9V/600mA)  
One User Guide  
1. Introduction  
MC200CM, MC210CS and MC220L are Gigabit Ethernet Media  
Converters. The FX port of MC220L supports hot-swappable.  
The converter mediates between a 1000Base-TX segment and a  
1000Base-X segment. It is primarily designed for larger bandwidth, and  
higher speed demanding workgroups that require expansion of the  
Gigabit Ethernet network  
Rear Panel  
Front Panel  
MC200CM&MC210CS  
1
 
     
Rear Panel  
Front Panel  
MC220L  
Note:  
This media convertor can also be powered by 5VDC Adapter.  
2. Features  
¾
¾
Comply with IEEE 802.3ab and IEEE 802.3z.  
Provide one SC/LC fiber connector and one RJ45 connector.  
Please check the table in page 3 for the accurate connector of each  
model.  
¾
Work at 1000Mbps in Full-Duplex mode for both TX port and FX  
port.  
¾
¾
Support auto MDI/MDIX for TX port.  
Extend fiber distance up to 0.55km for multi-mode fiber and 15km  
for single-mode fiber. Please check the table in page 3 for the  
accurate transmission distance of each model.  
¾
¾
Easy-to-view LED indicators provide status to monitor network  
activity easily.  
External power supply.  
2
 
   
¾
FX port supports hot-swappable(only for MC220L).  
Connectors and Network Cables Supported  
The connectors and network cables supported by the converter are  
listed as follows.  
¾
¾
Connectors: RJ-45, SC, LC.  
Network Cables: Cat.5 Twisted-Pair(below abbreviated as TP),  
9/125um Single-mode fiber, 62.5/125,50/125um Multi-mode fiber.  
Output  
Center  
Wavelength  
Transmission  
Distance  
Transmission  
Media  
Interface  
Model No.  
0.55km(50/125um)  
0.22km(62.5/125um) Fiber,TP  
Multi-mode  
MC200CM  
RJ45--SC  
850nm  
Single-mode  
Fiber,TP  
MC210CS  
MC220L  
RJ45--SC 15km  
1310nm  
850nm/1310  
nm  
RJ45--LC 0.55km/10km  
Multi/single-mode  
SC fiber connector and LC fiber connector  
3. Appearance Indication  
3.1 LED Indicators  
This converter has LED indicators which can provide a real-time report.  
3
 
     
When you take a look at these indicators, you will know what’s  
happening on your network.  
PWR  
LINK  
RX  
LINK  
FX  
TP  
Name  
Status Indication  
On  
Off  
On  
Off  
On  
Off  
On  
Power on  
Power off  
PWR  
There’s a valid link for FX Port.  
FX LINK  
LINK  
There’s no valid link for FX Port.  
There’s a valid link for TP Port.  
There’s no valid link for TP Port.  
The converter is receiving data from TP port.  
TP  
RX  
The converter is not receiving data from TP  
port.  
Off  
Note:  
The TP port mentioned in this User Guide Manual stands for the TX port  
without any explanations.  
3.2 Switch  
Force  
AUTO  
¾
FORCE: The FX port operates in FORCE mode.  
4
 
   
¾
AUTO: The FX port operates in Auto-Negotiation mode.  
Note:  
Be sure the opposite end is using the same setting. When using two  
converters at the same time, the two converters must be set to FORCE  
mode. When connected to other products, such as TL- SL2210WEB or  
TL-SL2428WEB, the converter must be set to Auto- Negotiation mode.  
We suggest leaving the switches on AUTO.  
Please reset the converter after configuring the switches. Then the  
change would take effect.  
4. Installation Guides  
4.1 Gigabit Ethernet Media Converter:  
¾
The SC fiber connector of MC200CM transmits/receives data by  
850nm short wave laser on multi-mode fiber.  
¾
The SC fiber connector of MC210CS transmits/receives data by  
1310nm short wave laser on single-mode fiber.  
Transmits and receives data on different fibers  
5
 
     
Note:  
Either two MC200CM or two MC210CS could cooperate. MC220L can  
be plugged in with two kinds of SFP modules, single-mode or  
multi-mode.  
Plug the SFP module into MC220L  
Transmits and receives data between two MC220L  
Note:  
Two MC220L with the same SFP module could cooperate.  
6
 
Transmits and receives data between MC220L and  
MC200CM/MC210CS  
Note:  
MC220L could be connected to MC200CM or MC210CS, however, the  
SFP module in MC220L must use the same mode and the same  
wavelength as the opposite end. (Please refer to the table below) And  
the connection fiber must be LC-SC fiber.  
Model No.  
MC220L connect with  
SFP module  
MC200CM  
MC210CS  
Transmission  
Media  
1310nm,  
Single-mode  
850nm, Multi-mode  
4.2 Configuration  
In order to achieve the aim of effectively expanding a Gigabit Ethernet  
network, please take the following examples for reference:  
1. Place two converters back to back between the following end  
devices.  
7
 
   
Note:  
For the correct connection between 2 Media Converters, please refer to  
connection diagram in 4.1 ---- two MC200CM, two MC210CS, two  
MC220L or one MC220L with another MC200CM/MC210CS.  
2. Another effective application is to place one converter directly  
between a 1000Base-TX network and a fiber optic (FX) device.  
4.3 Installation Procedure  
Use a fiber cable to connect two converters, or connect a converter with  
a 1000Base-FX Device.  
1. Connection of a Converter and a 1000Base-TX Device (HUB or  
Switch): Make sure that the length of the Cat.5 twisted pair cable  
(Category-5) between the 1000Base-TX device and the converter is  
less than 100 meters. Connect one end of the Cat.5 twisted pair  
cable to the RJ45 jack on the converter and the other end of the  
cable to the RJ45 jack on the 1000Base-TX device.  
8
 
   
2. Connection of two Converters or a Converter and a 1000Base- FX  
Device: Use a SC fiber cable to connect the two Converters’ SC  
connectors or the SC connecters of  
1000Base-FX Device.  
a
Converter and  
a
3. Turn on the power.  
4.4 Install Media Converter into MC1400  
Tweak out the two screws located on either side of the Chassis’s one  
side, and use them to install the retainer as follows.  
1. Turn off the switch power, take off the front guard on the chassis,  
insert the boxlike Media Converter you need in the slot of the  
chassis, and use locking knob to lock it tightly as follows.  
2. Turn on the switch power and you will see the Media Converter’s  
9
 
   
POWER LED lit on. Then you can operate it as the boxlike Media  
Converter of the MC series.  
5. Troubleshooting  
If you encounter some problems when you install or use this product,  
please try to solve the problem according to the following steps. If it still  
doesn’t work, please contact your dealer or ask for help from our  
technical support.  
1. PWR LED is off: The power error. Please check that whether the  
power lead is connected correctly or not.  
2. LINK LED (TP port) is off: Please confirm that there is no open  
circuit with cable and make sure that the connection type of the  
device is 1000M.  
3. LINK LED (FX port) is off:  
1) Check the fiber mode and fiber type to make sure that they  
match the Gigabit transceivers.  
2) Check out that whether there is an open circuit or not.  
3) Check the fiber loss by the Fiber-Optic Tester to avoid the  
excess wastage of the fiber.  
4) Make sure that the FX port is connected correctly as following:  
The transmitting port (TX) of local end is connected to the  
receiving port (RX) of outlying end. And the receiving port (RX)  
of local end is connected to the transmitting port (TX) of  
outlying end.  
10  
 
   
6. Appendix: Specifications  
MC200CM  
Standards and Protocols  
Media Interface  
IEEE802.3ab, IEEE 802.3z, IEEE 802.3x  
SC, RJ45  
Cat.5: 100m  
Max. Distance  
Power  
Multi-mode Fiber: 0.55km  
External Power Adapter  
Operation: 0℃~40℃  
Temperature  
Storage: -40℃~70℃  
Operation: 10%~90% non-condensing  
Storage: 5%~90% non-condensing  
Humidity  
MC210CS  
Standards and Protocols  
Media Interface  
IEEE802.3ab, IEEE 802.3z, IEEE 802.3x  
SC, RJ45  
Cat.5: 100m  
Max. Distance  
Power  
Single-mode Fiber: 15km  
External Power Adapter  
Operation: 0℃~40℃  
Temperature  
Storage: -40℃~70℃  
Operation: 10%~90% non-condensing  
Storage: 5%~90% non-condensing  
Humidity  
11  
 
   
MC220L  
Standards and Protocols  
Media Interface  
IEEE802.3ab, IEEE 802.3z, IEEE 802.3x  
LC, RJ45  
Cat.5: 100m  
Max. Distance  
Power  
Multi/Single-mode Fiber: 0.55km/10km  
External Power Adapter  
Operation: 0℃~40℃  
Temperature  
Storage: -40℃~70℃  
Operation: 10%~90% non-condensing  
Storage: 5%~90% non-condensing  
Humidity  
12  
 
 

TC electronic SDN BHD Guitar NM 1 User Manual
TDK Network Card HHM Series HHM1589D1 User Manual
Toshiba CRT Television 14N21NS User Manual
Toshiba TV DVD Combo MD14F52 User Manual
TP Link Network Router TL WR1042ND User Manual
Vacuflo Vacuum Cleaner 260 User Manual
Vantec Computer Drive MRK 300FD BK User Manual
VTech Cordless Telephone GiGA58x VT5836 User Manual
Walker Telephone W 300 User Manual
Waring Convection Oven TCO650 User Manual