Sylvania TV VCR Combo C6309CD User Manual

OWNER’S

MANUAL

9-INCH COLOR TV/VCR

C6309CD

This Owner’s Manual is made of

recycled paper.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

energy efficiency. ENERGY STAR^®is

a U.S. registered mark.

TOLL FREE : 1-800-287-4871.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit,

size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements

for the grounding electrode. (Fig. A)

19.Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions, as improper adjust-

ment of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the TV/VCR to its normal operation.

14.Lightning-For added protection for this TV/VCR receiver

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the TV/VCR due to lightning and

power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this TV/VCR, ask the service technician to perform routine

safety checks to determine that the TV/VCR is in proper

operating condition.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch dan-

gerous voltage points or short out parts that could result in

a fire or electric shock. Never spill liquid of any kind on

the TV/VCR.

22.Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18.Servicing-Do not attempt to service this TV/VCR yourself

as opening or removing covers may expose you to danger-

ous voltage or other hazards. Refer all servicing to quali-

fied service personnel.

- 3 -

9J27

PRECAUTIONS

AVOID THE HAZARDS OF

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top and bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

ELECTRICAL SHOCK AND FIRE

•

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If, by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

WARNING

•

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place,

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

ature differences are extreme.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted

material may violate applicable copyright laws. We assume no responsibility for the unauthorized duplication,

use, or other acts which infringe upon the rights of copyright owners.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

_{Download from Www.Somanuals.c}-_om4_.-_{All Manuals Search And Download.}

9J27

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .19

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .19

TRACKING ADJUSTMENT . . . . . . . . . . . . . .19

PICTURE SEARCH . . . . . . . . . . . . . . . . . . . .19

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .19

NOISE CANCEL (in the Still mode) . . . . . . . .19

VERTICAL HOLD CONTROL . . . . . . . . . . . .19

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C VIDEO CASSETTE . . . . . . . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND FUNCTIONS 8

C SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . .20

RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .20

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .20

C SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

ZERO RETURN . . . . . . . . . . . . . . . . . . . . . . .21

TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . .21

C PREPARATION FOR USE . . . . . . . . . . . . . . .10

ANTENNA/CABLE CONNECTIONS . . . . . . .10

MOBILE CONNECTION . . . . . . . . . . . . . . . .11

INSTALLING THE BATTERIES . . . . . . . . . . .12

EXTERNAL INPUT MODE . . . . . . . . . . . . . .12

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22

NORMAL RECORDING . . . . . . . . . . . . . . . . .22

SKIPPING UNWANTED SCENES DURING

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .22

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .13

CHANNEL SET UP FOR THE FIRST TIME .13

DELETING (OR ADDING) CHANNEL . . . . .13

CHANNEL SET UP AGAIN . . . . . . . . . . . . . .14

SELECTING THE LANGUAGE . . . . . . . . . . .14

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .14

CLOCK SET UP (AUTO / MANUAL) . . . . . .15

OTR (One Touch Recording) . . . . . . . . . . . . . .23

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . . . . . . . . . . .23

C TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

AUTOMATIC TIMER RECORDING . . . . . . .24

TIMER PROGRAM EXTENSION . . . . . . . . .25

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .26

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .17

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .17

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .17

REAL TIME TAPE COUNTER . . . . . . . . . . . .17

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .17

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .26

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .26

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .27

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .27

C TROUBLESHOOTING GUIDE . . . . . . . . . . .28

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .29

C CABLE CHANNEL DESIGNATIONS . . . . . .29

C WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . .30

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .18

WATCHING A TV PROGRAM . . . . . . . . . . . .18

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .18

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .18

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

- 5 -

9J27

FEATURES

Infrared remote control

Bilingual on screen menu display selectable in

English or French

Still–“Freeze” the picture at any time, for close viewing

of a particular scene. Only tapes recorded in SLP mode

will show a fairly clear picture.

•

Digital Auto Tracking (DTR)–Automatically adjusts the

tracking for each tape you play.

Rental play mode–Improves playback picture quality

from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a tape

indefinitely without pressing the PLAY button.

Time search–Let you set the TV/VCR to advance the

tape by entering the desired playback time you want to

skip.

OTR (One Touch Recording)–Instant timed recording

from 30 to 480 minutes is possible at the push of the

REC/OTR button.

1 Year, 8 events (including Daily and Weekly Timer

Recording)–The built-in timer allows you to record up

to 8 programs at different times on different channels up

to 1 year in advance. The Daily timer allows recordings

to be made of daily broadcasts, and the Weekly timer

allows recording to be made once a week up to the end

of the tape.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the recording.

Wake up/Sleep timer–Allows you to have the TV/VCR

automatically turn on or off at a desired time.

Timer Program Extension–Allow you to shift the time

schedule for automatic timer recording.

Two- way power–Allows you to power the TV/VCR

with standard household AC or your vehicle’s battery,

using the supplied car-battery cord.

•

Real time counter–This shows the elapsed recording or

playback time in hours, minutes, and seconds. The “–”

indication will appear when the tape is rewound further

than the tape counter position “0:00:00”.

181 channel capability PLL frequency synthesizer

tuner with direct station call–(A converter may be nec-

essary to view scrambled cable channels.)

•

Auto Clock Setting–Allows you to set the clock function

from a PBS broadcast station.

•

Game mode–Automatically sets external input mode and

allows TV/VCR display to be suitable for use with TV

games.

Auto power on and off system–Automatically turns on

the TV/VCR when you insert the cassette, turns off after

auto-rewind, and ejects when the beginning of the tape is

reached.

•

Auto rewind when the end of a tape is reached–This

function doesn’t occur when using timer recording.

•

2 Step picture search operation–You can view a video

program at a high speed or super high speed in either a

forward or reverse direction in LP and SLP mode. For

SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video heads as

you insert or remove a cassette.

Zero Return–The tape returns to counter of 0:00:00 by

rewinding or fast forwarding.

•

SUPPLIED ACCESSORIES

Car Battery Cord

Remote Control Unit

Dipole Antenna

Matching Adapter

(300ohm-75ohm)

(1813641 or 1780258 or

UCPGANTPK004)

2 AA Batteries

(0EMN00723 or

0EMN01183)

WPZ0202GA004

PART NO. (N0150UD)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

287-4871.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

_{Download from Www.Somanuals.c}-_om6_.-_{All Manuals Search And Download.}

9J27

VIDEO CASSETTE

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

PRECAUTIONS

INSERTING A CASSETTE

Avoid moisture. Moisture condensation may occur

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

•

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

Window

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

WRONG

CORRECT

TWO DIFFERENT TAPE SPEEDS

REMOVING A CASSETTE

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

1)In the Stop mode, press the EJECT button on the

remote control or press the STOP/EJECT button on

the TV/VCR. The cassette will eject.

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

2)Pull the cassette out of the cassette compartment.

3)Store the cassette in its case as shown.

Tape Speed

Type of tape

SP mode

Recording/Playback Time

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

Note: You can play back a tape recorded in LP mode

(Long Play).

ERASE PREVENTION

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

If you decide to record on

the tape again, cover the

hole with plastic tape.

Transparent Tape

- 7 -

9J27

OPERATING CONTROLS AND FUNCTIONS

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- TV/VCR FRONT PANEL -

POWER

STOP/EJECT

REW

PLAY

F.FWD

REC/OTR

VOLUME

CHANNEL

VIDEO AUDIO

EARPHONE

REC

1 2 3 4

5 6 7 8 9 10 11

12 13 14

2 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

- REMOTE CONTROL -

3 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer

Recording.

4 Remote Sensor Window– Receives the infrared

signals from the remote control.

5 POWER button– Press to turn TV/VCR on and off.

Press to activate timer recording.

6 STOP button– Press to stop the tape motion.

EJECT button– Press in the Stop mode to remove

tape from TV/VCR.

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

CHANNEL

VOLUME

+100

DISPLAY

MUTE

L button–

Press to select setting modes from the on screen

menu.

•

PLAY

Press to enter digits when setting program.

•

REW

F.FWD

STOP

(for example: setting clock or timer program)

7 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

s button–

COUNTER

RESET

Press to select a mode from a particular menu.

•

(for example: LANGUAGE or USER’S SET UP)

8 PLAY button– Press to begin playback.

K button–

Press to select setting modes from the on screen

menu.

•

1 VIDEO input jack– Connect to the video output

jack of your video camera or another VCR.

Press to enter digits when setting program.

(for example: setting clock or timer program)

•

_{Download from Www.Somanuals.c}-_om8_.-_{All Manuals Search And Download.}

9J27

- REAR VIEW -

9 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

B button–

125, first press the “+100” button then press “2”

and “5”).

16 MENU button– Press to display the main menu on

the TV screen.

When setting program (for example: setting clock

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 17.)

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

•

or timer program), press to determine your selec-

tion and proceed to the next step you want to

input.

Press to determine setting modes from on screen

menu.

•

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 25.)

Press to select a mode from a particular menu.

•

(for example: LANGUAGE or USER’S SET UP)

10 REC button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

COUNTER RESET button– Press to reset counter

to 0:00:00.

20 GAME button– Sets the game mode and external

input mode at the same time. (See page 18.)

21 TIME SEARCH button– Press to activate Time

Search mode.

11 VOLUME

buttons– Adjust the volume

level.

12 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

You may display the main menu on the TV screen

by pressing repeatedly this button on the

TV/VCR.

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

23 MUTE button– Mutes the sound. Press it again to

resume sound.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

mode. (See page 19.)

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

25 WAKE-UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See pages 26-27.)

26 ANT. terminal– Connect to an antenna or cable

system.

27 DC 13.2V jack– Connect to the Car Battery Cord.

28 Power cord– Connect to a standard AC outlet

(120V/60Hz).

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

+100 button– When selecting cable channels

which are higher than 99, press this button first,

then press the last two digits. (To select channel

- 9 -

9J27

PREPARATION FOR USE

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor

antenna.

ANTENNA/CABLE

CONNECTIONS

DIPOLE ANTENNA HOOK UP

VHF Antenna (Not supplied)

1. Push the stem of the Dipole Antenna (accessory)

into the hole for antenna at the back of TV/VCR.

2. Connect the flat twin-lead cable from the Dipole

Antenna to the 300/75 ohm Matching Adapter

(accessory).

UHF Antenna

(Not supplied)

VHF/UHF

Combiner

(Not

3. Plug the Matching Adapter to ANT terminal of

TV/VCR as shown in drawing.

For the best reception, extend the Dipole Antenna

and adjust its length and position. (Avoid handling

the top section when making adjustments).

supplied)

ANT.

NOTE: If it is difficult to get good reception with

the indoor antenna, the use of an outdoor antenna is

recommended. Before an outdoor antenna is connect-

ed to the set, the indoor antenna should be discon-

nected.

Flat twin-lead cable

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

Flat twin-lead cable

Dipole Antenna

(Supplied)

Matching

Adapter

(Supplied)

NOTE: This unit will ONLY record and view the

same channel.

From Cable System

ANT.

VHF/UHF COMBINED ANTENNA

A VHF UHF 75 ohm combination antenna can be

connected to ANT terminal.

75-ohm Coaxial

Cable (Not

supplied)

ANT.

Antenna/Cable Connections Continued on the Next Page.

- 10 -

9J27

1) The supplied indoor antenna is adequate when

your vehicle is stationary. For best reception on

the road, use a high-quality VHF/UHF mobile TV

antenna.

2) Attach the car battery cord to the DC13.2V con-

nector on the back of the TV/VCR. Then, connect

the other end to your vehicle’s cigarette-lighter

socket.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown here.

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

To the vehicle's

cigarette-lighter socket

VHF/UHF

Combination

Mobile Antenna

(Not supplied)

Satellite Box or

Cable Box (Not supplied)

OUT

Car battery cord

(Supplied)

From Cable System

or Satellite Dish

DC13.2V

ANT.

75-ohm Coaxial

Cable

(Not supplied)

NOTES:

ANT.

Be sure your vehicle has a 13.2-volt, negative-

ground electrical system.

•

Be sure you use only the supplied car battery cord.

Using another cord could damage the TV/VCR.

•

Be sure the socket is free of ashes and other debris.

Be sure to push the car battery cord’s plug com-

pletely into the cigarette-lighter socket.

Always unplug the car battery from the cigarette-

lighter socket before you unplug it from the

TV/VCR.

You must disconnect the car battery cord from the

•

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

1.Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

•

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

•

TV/VCR before you can use the AC power.

Be sure to replace the fuse with only the same

type, 5A, 250V.

•

MOBILE CONNECTION

Be sure the AC cord is wound as shown below.

•

WARNING:The driver should never watch

the TV/VCR while operating a motor vehicle.

CAUTION: If you use the TV/VCR with the

vehicle’s engine off, recharge the vehicle’s

battery after about every 4 hours of use to

prevent it from running down. After you fin-

ish using the TV/VCR be sure you unplug the

car-battery cord from the cigarette-lighter

socket.

- 11 -

9J27

INSTALLING THE BATTERIES

EXTERNAL INPUT MODE

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO IN/ VIDEO IN jacks of

your TV/VCR. Then press the CHANNEL K or

button until “AUX” appears on the screen.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

AUX

3)Replace the cover.

- 12 -

9J27

SET UP FOR USE

You can program the tuner to scan all the channels you receive in your area.

NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just

select the TV/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3). Then

select the channel to be viewed on the Cable Box or Satellite Box.

CHANNEL SET UP FOR THE

FIRST TIME

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you can

add the deleted channel into the memory again.)

1 Plug in the TV/VCR power cord

Plug the TV/VCR power cord into a stan-

dard AC outlet.

NOTES:

1 Select “CHANNEL SET UP”

You must disconnect the car battery

•

– M E N U –

Press the MENU button on the

cord from the TV/VCR before you use

AC power.

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

If some digits appear in the corner of the screen,

press the POWER button without unplugging the

power cord.

•

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

2 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

– CHANNEL SET UP –

ADD / DELETE CH (TV)

AUTO PRESET

3 Select “ENGLISH” or “FRANÇAIS”

Select “ENGLISH” or

“FRANÇAIS”=French using the

F.FWD/B or REW/s button. “[ ]”

indicate the selected language.

– SET UP –

Press the F.FWD/B button.

LANGUAGE

[ENGLISH] FRANÇAIS

AUTO PRESET

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it) (Example:

CH8)

4 Begin auto preset

– SET UP –

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then press the F.FWD/B button.

The tuner scans and memorizes all

active channels in your area.

NOTES:

ADD / DELETE

LANGUAGE

[ENGLISH] FRANÇAIS

AUTO PRESET

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

The TV/VCR distinguishes between standard TV

channels and cable channels.

•

If you want to play or record a video tape BEFORE

presetting the tuner, you must press the MENU but-

ton on the remote control. To preset the tuner again,

see “CHANNEL SET UP AGAIN” on page 14.

The TV/VCR may recognize TV channels to be

CATV channels by the receiving conditions. In this

case, try auto preset again in the fine receiving

conditions.

•

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

again, the channel is memorized again.

•

Added channel: Light blue.

Deleted channel: Light red.

•

5 Exit the channel setup mode

Press the MENU button on the remote control to

returns to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

5 After scanning

The tuner stops on the lowest memorized channel.

If you want to recall the selected channels, you can

select the desired channel directly with the remote

control number buttons or CHANNEL K or L.

- 13 -

9J27

NOTE: If for some reason the menu is in French,

press the MENU button on the remote control, press

the PLAY/K button to point to “LANGAGE

[FRANÇAIS]”, then press the F.FWD/B button, then

press the MENU button on the remote control.

CHANNEL SET UP AGAIN

Make sure ...

Press the POWER button to turn on the TV/VCR.

•

1 Select “CHANNEL SET UP”

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

Then, press the F.FWD/B button.

First Sunday of April : At 2 AM the clock imme-

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

2 Begin auto preset

– CHANNEL SET UP –

Press the PLAY/K or STOP/L but-

ton to point to “AUTO PRESET”.

Then, press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

ADD / DELETE CH (TV)

AUTO PRESET

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

Press the POWER button to turn on the TV/VCR.

•

3 After scanning

The tuner stops on the lowest memorized channel.

1 Select “SETTING CLOCK”

Press the MENU button on the

– M E N U –

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

SELECTING THE LANGUAGE

Make sure ...

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

TIME SEARCH

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

Then, press the F.FWD/B button.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “D.S.T.”.

Then, press the F.FWD/B or

REW/s button until [ON] appears.

– SETTING CLOCK –

1 Select “LANGUAGE”

– M E N U –

TIMER PROGRAMMING

AUTO CLOCK

[ON]

Press the MENU button on the

PICTURE CONTROL

AUTO CLOCK CH SEARCH

SETTING CLOCK

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

CHANNEL SET UP

remote control.

Press the PLAY/K or STOP/L but-

USER’S SET UP

[ON]

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

ton to point to “LANGUAGE”.

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

2 Select “ENGLISH” or “FRANÇAIS”

Select “ENGLISH” or “FRANÇAIS”= French using

the F.FWD/B or REW/s button.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

3 Exit the Language mode

Press the MENU button on the remote control to

return to TV mode.

F.FWD/B or REW/s button.

- 14 -

9J27

CLOCK SET UP

– MANUAL CLOCK SET –

MONTH DAY YEAR

6 Select the hour

(AUTO / MANUAL)

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

0 5

0 6 TUE 2 0 0 3

The TV/VCR clock must be set correctly before

VCR timer recording is possible. It is suggested that

the clock be set manually when first setting up the

TV/VCR. Then, set to [ON] the auto clock setting

which will periodically correct the setting if neces-

sary.

NOTE: If you cannot receive a station with time sig-

nals, auto clock setting cannot be performed. Use

manual setting only.

HOUR

0 5

MINUTE

– – PM

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: 40)

0 5

0 6 TUE 2 0 0 3

HOUR

0 5

MINUTE

4 0 PM

MANUAL CLOCK SETTING

5:40 PM

8 Start the clock

Make sure ...

Press the MENU button on the

remote control.

The TV/VCR is turned on.

In the example below, the clock is to be set to:

•

Although seconds are not displayed,

they begin counting from 00 when

DATE

May 6th, 2003

SETTING TIME 5:40PM

you press the MENU button on the remote control.

Use this feature to synchronize the clock with the

correct time.

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

– M E N U –

NOTE:

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

TO CHANGE CLOCK SETTING

Then, press the F.FWD/B button.

If you want to change the clock,

1)Follow steps [1] and [2].

2)Select where you want to change using the

F.FWD/B or REW/s button.

3)Enter correct numbers using the PLAY/K or

STOP/L button.

2 Select “MANUAL CLOCK SET”

Press the PLAY/K or STOP/L but-

ton to point to “MANUAL

CLOCK SET”.

Then, press the F.FWD/B button.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02

]

[OFF]

4)Press the MENU button on the remote control to

start the clock.

– MANUAL CLOCK SET –

MONTH DAY YEAR

3 Select the month

PLEASE NOTE:

Press the PLAY/K or STOP/L but-

ton until your desired month

appears. (Example: May → 05)

Then, press the F.FWD/B button.

0 5

– – – – – – – – –

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the F.FWD/B or REW/s button to turn [OFF]

this function. Then you can manually adjust the

clock.

HOUR

– –

MINUTE

– – – –

– MANUAL CLOCK SET –

MONTH DAY YEAR

4 Select the day

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 6th → 06)

0 5

0 6 – – – – – – –

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2003)

0 5

0 6 TUE 2 0 0 3

HOUR

– –

MINUTE

– – – –

Then, press the F.FWD/B button.

- 15 -

9J27

AUTOMATIC CLOCK SETTING

Make sure ...

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 15.

The TV/VCR is turned on.

Confirm the TV/VCR is receiving a RF (Radio

Frequency) signal from either an antenna or cable

system connection using the ANT IN jack on the

rear of the TV/VCR.

•

Press the MENU button to exit the screen.

NOTE: During Auto Clock CH Search, the picture

may be distorted. This is normal.

•

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L

NOTE:

If a cable converter box is being used, make sure it

is powered on.

You must use the TV/VCR remote control to per-

form the clock setting procedure.

•

button to select “SETTING

CLOCK”.

Press the F.FWD/B button to

enter “SETTING CLOCK” menu.

Press the STOP/L button to select

“AUTO CLOCK CH”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

If the TV/VCR is connected directly to a cable

•

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically.

TIME SEARCH

Press the F.FWD/B or REW/s

buttons until you locate Auto

Clock Set station number. See

item 3 above.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[

45]

[OFF]

1 Select “SETTING CLOCK”

Press the MENU button to exit the

screen.

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

5 Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically

check and set the correct date and time.

TIME SEARCH

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B button until

AUTO CLOCK [ON] appears.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

3 Begin “AUTO CLOCK CH SEARCH”

Press the STOP/L button to select

– SETTING CLOCK –

“AUTO CLOCK CH SEARCH”.

Press the F.FWD/B button.

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

The TV/VCR is now searching

•

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

seconds per channel.

– AUTO CLOCK CH SEARCH –

“_ _” appears at the lower left of

the screen when the search has

ended.

•

_ _

Auto Clock station- write down

•

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

4 below.

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

•

- 16 -

9J27

ON SCREEN DISPLAY

To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as fol-

lows:

OFF mode

Counter mode

Clock mode

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

STOP

5:40PM

CH2

COUNT 0:12:34

After 5 seconds

5:40PM

CH2

COUNT 0:12:34

Counter

remains

Clock & Channel

remains

SPECIAL FEATURES

DEGAUSSING

AUTO REWIND-EJECT

Magnetism from nearby appliances might affect the

color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

When the end of a tape is reached during record-

ing, playback, or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

•

REAL TIME TAPE COUNTER

This shows the elapsed recording or playback time in

hours, minutes, and seconds. (The displayed time

will not change on a blank tape or blank portions on

the tape.)The “–” indication will appear when the

tape has rewound further than “0:00:00” on the tape

counter.

- 17 -

9J27

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

3 Adjust sound

Press the VOLUME X or Y button

to adjust the volume.

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

Press the PLAY/K or STOP/L but-

ton to point to ”PICTURE CON-

TROL”.

VOLUME 20

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

GAME MODE

2 Select item you want to adjust

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

Press the PLAY/K or STOP/L but-

ton until desired control is dis-

played.

NOTE: This function can not be set during recording.

BRIGHT

–

P +

CONTRAST

COLOR

TINT

GAME

Press the GAME button on the

remote control. “GAME” appears

on the screen.

SHARPNESS

When you press the GAME button;

3 Adjust the picture control

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

matically.

•

Press the F.FWD/B or REW/s button to adjust to

your desired level.

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS to soft

to pale

to brilliant

to purple

to green

to clear

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 18 -

9J27

PLAYBACK

2)Press it again and the TV/VCR will now search in

NORMAL PLAYBACK

super high speed. (in the LP / SLP modes only)

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the pic-

ture may revert to Black and White. This is normal.

3)Press the PLAY button to return to normal speed.

Make sure ...

TV/VCR power must be turned on.

•

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines.Press

the PLAY button to return to playback.

NOTES:

PLAY

2 To begin playback

Press the PLAY button.

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

•

3 To stop playback

Press the STOP button when play-

back is completed.

STOP

This is not a fault of the machine, but is a by-

product of the technology involved in producing

a TV/VCR with 2 video heads.

If it is left in the Pause mode for more than five

minutes, the TV/VCR will automatically switch to

the Stop mode.

TRACKING ADJUSTMENT

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

However when playing pre-recorded tapes or tapes

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

NOISE CANCEL

(in the Still mode)

This feature allows you to reposition or reduce the

noise lines of a still picture.Press the PAUSE/STILL

button so that the noise lines change position on the

screen so you can see the picture in its entirety with-

out distracting noise lines.

NOTE: This feature can be activated ONLY when

viewing a tape recorded in the SLP mode. If the tape

was originally recorded in the SP or LP mode, the

still picture may revert to black and white in addition

to the “noise bars”. This is normal.

PICTURE SEARCH

VERTICAL HOLD CONTROL

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

In the Pause/Still mode only, when the picture begins

to vibrate vertically, stabilize the picture by pressing

the CHANNEL K or L button.

1)You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD or REW button during playback. (in the

SP / LP / SLP modes)

NOTE:

If there are video noise lines on the screen, reposition

or reduce them. Refer to “NOISE CANCEL”.

- 19 -

9J27

SPECIAL PLAYBACK

Make sure ...

AUTO REPEAT PLAYBACK

The TV/VCR has the auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

TV/VCR power must be turned on.

Insert a prerecorded tape.

•

Before playback, follow steps below.

•

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

RENTAL PLAYBACK

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

PICTURE CONTROL

remote control.

CHANNEL SET UP

SETTING CLOCK

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L but-

ton to point to “REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your desired

selection [ALL] or [BLANK]

appears.

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

USER’S SET UP

–

USER’S SET UP

–

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

4 Start playback

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

4 Start playback

Press the PLAY button to start the Repeat Play.

”REPEAT PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

•

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

•

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

- 20 -

9J27

Make sure ...

TV/VCR power must be turned on.

Insert a tape.

•

This function will not operate in recording mode.

This function is not operative when a cassette tape

is not inserted in the TV/VCR.

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

•

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

1 Insert a tape.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minute).

– M E N U –

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

TIMER PROGRAMMING

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

ton to point to “TIME SEARCH”.

Then, press the F.FWD/B button.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

3 Enter your desired time

Press the PLAY/K or STOP/L but-

ton until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

If you wish to cancel the Time

Search at this point, press the MENU button on the

remote control.

TIME SEARCH

2 : 50

4 To activate “ZERO RETURN” mode

Press the MENU button on the

– M E N U –

TIMER PROGRAMMING

remote control.

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

Press the PLAY/K or STOP/L but-

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

ton to point to “ZERO RETURN”.

Then, press the F.FWD/B button.

The counter will appear on the TV screen.

The tape will automatically stop when the counter

returns to 0:00:00.

4 Begin Time Search

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

TIME SEARCH

The Time Search function makes it possible to quick-

ly advance the tape to your desired position simply

by entering the exact amount of playback time you

want to skip.

TO CANCEL THE TIME SEARCH at this

point

NOTES:

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

Time Search can be set up to a maximum of 9

hours 50 minutes (9:50) by 10 minutes at a time.

•

- 21 -

9J27

RECORDING

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTE: This unit will ONLY record and view the same channel.

SKIPPING UNWANTED

SCENES DURING RECORDING

NORMAL RECORDING

You can ONLY watch the same TV program that is

being recorded.

Press the PAUSE/STILL button to

temporarily stop recording.

Press the PAUSE/STILL or

RECORD button to resume record-

ing.

PAUSE

1 Select the channel to be recorded

Press the number buttons on the

remote control or the CHANNEL

K or L button.

Remember: If the TV/VCR is con-

nected to a cable box or satellite

box, the TV/VCR must be on CH3 or CH4, then the

channel to be recorded must be selected on the cable

box or satellite box.

CH 10

NOTE:

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape dam-

age.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

3 Begin recording

Press the RECORD button.

REC

4 Stop recording

Press the STOP button when recording is completed.

- 22 -

9J27

OTR (One Touch Recording)

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/VCR.

Push(es) Display

1 push

Recording length

(normal recording)

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

NOTES:

This function CANNOT be done from the remote

control.

•

17 pushes

8:00

480 minutes

•

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

You can make copies of video tapes made by friends

or relatives for your enjoyment.

•

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Recording starts immediately when the REC/OTR

button is pressed.

When the REC/OTR button is pressed 18 times, the

TV/VCR returns to the Normal Recording mode.

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

•

To show the remaining time, press the DISPLAY

•

button on the remote control so that “OTR”

appears on the TV screen. (It will show up momen-

tarily then disappear.)

POWER

[The TV/VCR]

VIDEO AUDIO

REC

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-120).

•

[Ex: Source (playing)

VCR or camcorder]

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, ejects the tape and turns itself off.

•

If you press the power button during OTR, the

TV/VCR continues recording until the selected

length is reached.

•

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

1 Select the channel to be recorded

Press the number buttons on the remote control or the

CHANNEL K or L button.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR’s cassette compart-

ment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

4)Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

5)Press the RECORD button on the TV/VCR.

6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during dubbing, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

3 Begin OTR

Press the REC/OTR button on the TV/VCR as many

times as needed. The recording length will be deter-

OTR(2 : 30)

mined by the number of times you

press the REC/OTR button. Each

additional push will increase the

recording time by 30 minutes. It is

set up to 8 hours.

- 23 -

9J27

TIMER

– M E N U –

And press the F.FWD/B button.

AUTOMATIC TIMER

RECORDING

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIME SEARCH

If you have not yet set the clock,

“MANUAL CLOCK SET”

appears. If so, follow steps [3] to

[8] on page 15. Then set the timer

recording.

•

In the example below, the timer is being set to record:

2 Select your desired program position (1~8)

DATE:

July 4th, 2003

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

ton to select the desired program

position.

CH DATE

BEGIN END

SETTING TIME: from 7:30PM to 8:50PM

- - -/- - - - - -:- -

-:- - - -

CHANNEL:

TAPE SPEED:

CH61

Then, press the F.FWD/B button.

Make sure ...

If a cable box or satellite box is connected with the

TV/VCR you will be limited to record only one

channel. And the channel selector on the TV/VCR

must be selected to the output channel of the boxes

CH 3 or CH 4 and then the actual channel to be

recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/VCR power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

(Example: CH61)

Then, press the F.FWD/B button.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

4 Select once, every day or weekly recording

For once recording :

The channel you want to record is properly set in

advance. (See page 14.)

•

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Press the PLAY/K (up) button

until the desired date appears.

(Example: “7/04” for July 4th).

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 7/04 FRI -:- -

- - -/- - - - - -:- -

-:- - - -

Avoid over lap of programs ...

There is a chance that a program will not be record-

ed. when programs overlap;

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

For every day recording : To record a TV program at

the same time on the same channel every day.

(Example: Monday through Sunday)

The illustration below demonstrates the sequence

of recordings.

•

– TIMER PROGRAMMING –

Press the STOP/L (down) button

Program 1

Program 2

Program 3

10:00AM - 11:00AM

9:00AM - 10:00AM

9:30AM - 12:00PM

CH DATE

BEGIN END

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

until “EVRY DAY” appears.

Then, press the F.FWD/B but-

ton.

Recording Sequence

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

9:30AM-12:00PM

For weekly recording : To record a TV program at

the same time on the same channel every week.

(Example: every Monday)

9:00AM

10:00AM

11:00AM

12:00PM

– TIMER PROGRAMMING –

*Recording period is SHADED

Press the STOP/L (down) button

CH DATE

BEGIN END

until “EVRY” and your desired

day of the week appear together.

Then, press the F.FWD/B but-

ton.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

1 Select “TIMER PROGRAMMING”

Press the MENU button on the remote control.

Confirm “TIMER PROGRAMMING” is pointed by

pressing the PLAY/K button.

- 24 -

9J27

TIMER PROGRAM EXTENSION

– TIMER PROGRAMMING –

CH DATE BEGIN END

5 Set beginning hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “ 7, PM” for 7:30PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

To shift the time schedule of an automatic timer

recording.

1)Press the POWER button.

61 7/04 FRI 7:12^P

- - -/- - - - - -:- -

2)Repeat step [1] on page 24.

3)Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4)Press the RECORD button again.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each additional

push will shift forward the end time only. If you

want to cancel while setting, press the

6 Set beginning minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “30” for

7:30PM)

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

61 7/04 FRI

7:30^P

- - -/- - - - - -:- -

Then, press the F.FWD/B button.

7 Set end hour

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automat-

ically be set to the SLP mode.

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then, press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

8:30^PM - -

-:- - - -

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

5)Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

8 Set end minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: “50” for

8:50PM)

- - -/- - - - - -:- -

-:- - - -

8:50^PM- -

-:- - - -

TO CORRECT A PROGRAM

61 7/04 FRI 7:30^P

- - -/- - - - - -:- -

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

Then, press the F.FWD/B button.

bers using the PLAY/K or STOP/L button.

After setting a program;

1)Press the POWER button.

•

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

– TIMER PROGRAMMING –

CH DATE BEGIN END

- - -/- - - - - -:- -

-:- - - -

2)Repeat steps [1] - [2] on page 24.

3)Press the F.FWD/B button (or press the REW/s

button to go back one step) until the part you

want to correct begins flashing, then make the

changes pressing the PLAY/K or STOP/L but-

ton.

61 7/04 FRI 7:30^P

8:50^P

- - -/- - - - - -:- -

-:- - - -

10 Finish setting the program

Press the F.FWD/B or REW/s button. The program

is now completed.

4)Press the POWER button to set automatic timer

recording.

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

return to original mode.

•

TO CANCEL AN AUTOMATIC TIMER

RECORDING

After setting a program;

1)Press the POWER button.

2)Repeat steps [1] ~ [2] on page 24 and select a

program you want to cancel.

3)Press the T-PROG. CLEAR button.

4)Press the MENU button on the remote control to

return to TV mode.

While recording is in progress;

1)Press POWER button.

2)Press the STOP/EJECT button on the TV/VCR.

•

11 Set the timer

Press the POWER button to set automatic timer

recording. The TIMER REC indicator lights up.

You must turn off the TV/VCR to activate automat-

ic timer recording.

•

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

•

- 25 -

9J27

TO CHECK THE BEGIN/END TIME

1)Press the POWER button so that the REC indicator

goes off.

2)Press the MENU button on the remote control.

3)Confirm “TIMER PROGRAMMING” is pointed.

4)Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

program(s).

NOTE:

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

5)Press the MENU button on the remote control to

return to TV mode.

4 Watch the recorded program

Press the PLAY button.

HINTS FOR AUTOMATIC

TIMER RECORDING

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

Make sure the channel you want to record is prop-

erly set in advance.

It is not necessary to press the RECORD button for

timer recording.

•

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

•

WAKE UP TIMER

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, and the tape will be ejected.

•

NOTES:

•

Use the remote control for this procedure.

Clock must be set to the correct time before setting

•

the timer.

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

AUTO RETURN

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

1 Select “WAKE UP TIMER”

Press the WAKE-UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

1 Select “USER’S SET UP”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

Press the F.FWD/B or REW/s

button until [ON] appears.

WAKE UP B ON/OFF

[ON]

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

LANGUAGE [ENGLISH]

ZERO RETURN

TIMER

TV/TAPE

TIME

[TV]

[12:00AM]

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then, press the F.FWD/B button.

TIME SEARCH

2 Select “TV” or “TAPE”

Press the PLAY/K or STOP/L but-

ton until to point to “TV/TAPE”.

Press the F.FWD/B or REW/s

button, and select [TV] or [TAPE].

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears.

USER’S SET UP

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

–

[TV]

[12:00AM]

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

- 26 -

9J27

3 Set wake up time

1 Select “SLEEP TIMER”

Press the PLAY/K or STOP/L but-

ton until to point to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

Press the WAKE-UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

WAKE UP

TIMER

ON/OFF

[ON]

TV/TAPE

[TV]

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

your desired sleep time appears.

B TIME

[12:00AM]

Each additional push will increase (or decrease) the

time by 10 minutes.

Each additional push will increase

SLEEP TIMER [2:00]

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

the time by 30 minutes up to 120

minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE WAKE UP TIMER

Repeat step [1] but select [OFF].

TO CANCEL THE SLEEP TIMER

Press the WAKE-UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer press the WAKE

UP/SLEEP button twice, then press the MENU but-

ton on the remote control to exit the sleep timer set-

ting.

SLEEP TIMER

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

NOTE:

This function does not operate during Recording

mode.

•

MAINTENANCE

1.Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-287-4871, to

locate an Authorized Service Center.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

Never use a solvent or alcohol. Do not spray insec-

•

NOTES:

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

Remember to read the instructions included with

the video head cleaner before use.

•

Clean video heads only when problems occur.

•

AUTO HEAD CLEANING

SERVICING

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

Should your TV/VCR become inoperative, do not

•

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord, and please call our help line at 1-800-

287-4871, to locate an Authorized Service Center.

Playback picture may become blurred of interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use, or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

back, the video heads in your TV/VCR may need

to be cleaned.

- 27 -

9J27

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the car battery cord is connected to vehicle’s cigarette

lighter socket and to DC 13.2V jack on back of the TV/VCR.

Check the fuse (5A, 250V) in car battery cord.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/VCR program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If need, cover the

hole with plastic tape.

No power.

•

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

Timer recording is not possible.

Cannot go into Record mode.

Playback picture is partially noisy.

Adjust tracking control for a better picture using the CHANNEL K

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 27.

No picture but the audio is OK in

playback.

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

Can not set the auto clock to ON.

Different color marks on screen.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

•

Make sure the AC cord is connected to an AC outlet.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the TV/VCR away from the appli-

ances, the TV/VCR can repair itself automatically. If you want to

repair immediately, unplug the TV/VCR power cord, then plug it in

again 30 minutes or so later.

- 28 -

9J27

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

9 inch in-line gun, 90˚

deflection tube

NTSC-M

Rotary two-head

1/2 inch

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

OTHER SPECIFICATIONS

Power requirement : AC 120V/60Hz

DC 13.2V

Power consumption : AC 55W / DC 60W

Dimensions :

#2~#6

#7~#13

#14~#69

H:13” (330mm)

W:12-1/8” (308mm)

D:12-15/16” (329mm)

18.5 lbs (8.4kg)

CATV

VHF :

Weight :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Designs and specifications are subject to change

without notice.

If there is a discrepancy between languages, the

default language will be English.

•

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 29 -

9J27

SYLVANIA HOME ENTERTAINMENT WARRANTY

We appreciate your purchase of a SYLVANIA Home Entertainment product. We take pride in the quality

of our products and have manufactured your new Home Entertainment unit to exacting quality standards.

We feel confident that in normal use, it will provide you with satisfactory performance. However, should

you experience difficulty, you are protected under the provisions of this warranty.

SYLVANIA Home Entertainment products are warranted against manufacturing defects in materials and

workmanship in normal use for the following periods from the date of purchase by the original user, and is

conditional upon the unit being installed and used as directed in the instruction manual.

COLOUR MONITOR / VCR COMBO

Parts and Labour

1 Year

Special Parts:

Picture Tube

Video Head

3 Years Parts / 1 Year Labour

6 Months Parts and Labour

90 Days Parts and Labour

Remote Control

SYLVANIA S obligation under this warranty shall be limited to the repair, including all necessary parts and

the cost of the labour connected therewith, or at our option the exchange of any Home Entertainment

product which shows evidence of a manufacturing defect within the warranty period.

Replacement parts, furnished in connection with this warranty shall be warranted for a period equal to the

unexpired portion of the original equipment warranty.

CUSTOMER OBLIGATIONS

This warranty applies to the product from the original date of purchase at retail. Therefore, the owner must

provide a copy of the original, dated bill of sale. No warranty service will be performed without a bill of

sale. Transportation to and from the service depot is the responsibility of the owner.

WARRANTY EXCLUSIONS

This warranty is extended to SYLVANIA Home Entertainment products purchased and used in Canada.

This warranty shall not apply to appearance or accessory items including but not limited to: cabinet, cabinet

parts, batteries, connecting cables, tapes. This warranty shall, in addition, not apply to cleaning

video/audio heads, pinch rollers, tape transport system damages due to handling, transportation,

unpacking, set-up, installation, customer adjustments that are covered in the instruction book, repair or

replacement of parts supplied by other than the SYLVANIA authorized service depot, any malfunction or

failure caused by or resulting from abnormal environmental conditions, improper unauthorized service,

improper maintenance, modifications or repair by the consumer, abuse, misuse, neglect, accident, fire,

flood, or other Acts of God, and incorrect line voltage.

This Home Entertainment product is only warranted to the original retail purchaser. This warranty

becomes void in the event of commercial or rental use. This warranty becomes void in the event serial

numbers are altered, defaced or removed.

SYLVANIA reserves the right to make changes in design or to make additions to or improvements upon

this product without incurring any obligation to install the same on products previously manufactured.

The foregoing is in lieu of all other warranties expressed or implied and SYLVANIA neither assumes nor

authorizes any person to assume for it any other obligation or liability in connection with the sale or service

of this product. In no event shall SYLVANIA or its SYLVANIA dealers be liable for special or consequential

damage arising from the use of this product, or for any delay in the performance of this warranty due to

cause beyond our control.

The purchaser may have other rights under existing provincial or federal laws, and where any terms of this

warranty are prohibited by such laws, they are deemed null and void, but the remainder of the warranty

shall remain in effect.

HOW TO OBTAIN SERVICE

Should this product require service, you may obtain specific information on how to obtain service by

contacting the SYLVANIA Dealer from whom this product was purchased, or by contacting us directly:

SONIGEM SERVICE

300 Alden Road

Markham, Ontario

L3R 4C1

PHONE: (905) 940-5089 FAX: (905) 940-2303

1-800-287-4871

Printed in Malaysia

0EMN02107

T4404CE * * * * *

Sharp Flat Panel Television LC 15B2UA User Manual
Solid State Logic Computer Hardware 82S6MC120A User Manual
Sony Automobile Electronics SNCDF40P User Manual
Sony Camera Lens SSCDC174 User Manual
Sony DVD Player DVD Player User Manual
Sony Microphone ECM 330 User Manual
Sony MP3 Player TCM 500DV User Manual
Sony Photo Printer UP DR80 User Manual
SOYO Computer Hardware SY 5EMA+ User Manual
Tanaka Chainsaw ECS 415 User Manual