®
BRITA Water Filter & Chiller II
Chilled water filter
Instruction Booklet
WF6100
Please read these instructions carefully
and retain for future reference.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR WATER FILTER
& CHILLER.
• Always place the appliance on a flat, even surface.
• Always unplug the appliance before changing the
filter.
• This water filter must only be used with municipally
treated water. Do not attempt to filter untreated, raw
water or water of unknown quality.
• This appliance has been designed to be used
continuously.
• Filter replacement is essential for the product to
perform as represented. The filter must be replaced
every eight weeks.
• Do not operate without a filter in place.
• Do not place this unit in an area that receives
direct sunlight. Placing the unit in direct sunlight
can affect unit performance as well as promote the
growth of algae.
• To protect against electric shock do not place the
cord, plug or appliance in water or any other liquid.
Sunbeam is very safety conscious when designing and
manufacturing consumer products, but it is essential
that the product user also exercise care when using
an electrical appliance. Listed below are precautions
which are essential for the safe use of an electrical
appliance:
• Do not use an appliance for any purpose other than
its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang over
the edge of a table or bench top or touch any hot
surface.
• Read carefully and save all the instructions provided
with an appliance.
• Always turn the power off at the power outlet before
you insert or remove a plug. Remove by grasping the
plug - do not pull on the cord.
• Turn the power off and remove the plug when the
appliance is not in use and before cleaning.
• Do not use your appliance with an extension cord
unless this cord has been checked and tested by a
qualified technician or service person.
• Always use your appliance from a power outlet of the
voltage (A.C. only) marked on the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• Do not operate any electrical appliance with a
damaged cord or after the appliance has been
damaged in any manner. If damage is suspected,
return the appliance to the nearest Sunbeam
Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam recommend the
use of a residual current device (RCD) with a tripping
current not exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate remote
control system.
• This appliance is intended to be used in household
and similar applications such as: staff kitchen areas
in shops, offices and other working environments;
farm houses; by clients in hotels, motels and other
residential type environments; bed and breakfast
type environments.
• Children should be supervised to ensure that they do
not play with the appliance.
• The temperature of accessible surfaces may be high
when the appliance is operating.
• Never leave an appliance unattended while in use.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
1
Features of your Water Filter
& Chiller
Memo display
Provides an indication of when the BRITA®
MAXTRA Cartridge needs to be replaced.
2 litre filtering tank
Holds two litres of water before it passes
through the BRITA® MAXTRA cartridge.
Power on and chilled indicator light
A white light will display when the unit is
turned on and will switch to blue to let you
know when water is chilled.
Water dispensing lever
Simply push the lever in to dispense fresh
tasting filtered and chilled water.
2
Lid
Protects your water from dust and other
impurities.
BRITA® Maxtra cartridge
Offers advanced filtration due to MAXTRA
Technology which reduces chlorine and
limescale as well as metals such as lead and
copper to give you great tasting water every
time.
4 litre filtered water tank
Holds 4 litres of water which travels to the
1.2 litre chilling reservoir.
Filter funnel
A key element of the filtration system
allowing filtered water to pass into the water
tank before it reaches the chilling reservoir.
1.2 litre chilling reservoir
Holds 1.2 litres of refreshing chilled water at
a time.
BRITA® MAXTRA filter cartridge
3
Using your Water Filter
& Chiller
Before using your Water Filter
& Chiller
• Carefully unpack the appliance and check
that all the components are included.
Please refer to pages 2-3.
• Remove the filter cartridge and put to one
side.
Do not re-insert until (a) flushing process
and (b) preparation of filter cartridge
procedures, as explained below, have been
completed.
• Wipe out the filtered water tank with a
damp cloth which has been soaked in
water.
• Position the appliance on a dry, level and
secure bench top. Allow for good airflow
around the appliance so do not place
directly against a wall.
• Do not position the unit in an area that
receives direct sunlight. Placing the unit in
direct sunlight may affect unit performance
as well as promote the growth of algae.
Flushing Process
• It is important that you flush and rinse out
the dispensing system before using the
appliance for the first time.
• Fill the water tank to the brim with hot tap
water.
• Place a large container or jug under the
spout.
• Press the dispenser lever until all the water
is dispensed and the water tank is empty.
• Repeat this flushing process twice with
cold tap water and discard.
• Please note that when flushing for the first
time, while pressing the dispensing lever,
no water will be dispensed until the tank
is almost empty as it will be filling the
chilling tank.
• Do not fill above the maximum level
indicated.
• Please note that you should carry out these
steps without the Maxtra cartridge in place.
• Plug the appliance into an appropriate
electrical outlet and switch on.
• A white power on light will be illuminated
to show that the appliance is switched on
and working.
4
Using your Water Filter & Chiller (continued)
Preparing the BRITA® MAXTRA filter cartridge
for use
Note: Repeat the cartridge preparation
process each time you insert a new cartridge.
• Remove the cartridge from its wrapping
(it is normal for the cartridge to appear
moist).
• Immerse the cartridge in cold water and
agitate gently to remove any air bubbles.
(See figure 1).
• Once the water has been filtered, you can
refill this section.
• This will then filter through as water is
dispensed.
• After approximately 4 hours, the power
light will change from white to blue to
indicate that the water has been chilled.
• The light may flicker from blue to white
as water is dispensed and if the ambient
temperature increases. The fan may be
activated in these conditions and will
remain so until the required temperature
has been reached.
Figure 1
• Insert the cartridge into the 2 litre filtering
tank and push it firmly into place until
it ‘clicks’.
• Place the filtering tank into the sink. Fill
the filtering tank from the tap with cold
water, and allow the water to pass through
the filter into the sink until empty. This
first filling is used to activate the filter
cartridge.
• Insert the filtering tank into the water tank.
Now refill with cold tap water, and the
system is ready for use.
• To exchange the cartridge, simply use the
ring pull handle on the top of the cartridge
to remove it from the funnel.
(See figure 2).
Figure 2
5
Using your Water Filter & Chiller (continued)
Filtering time
• At the end of every two weeks, one
bar will disappear to indicate the
remaining cartridge life. When only one
bar is showing, ensure that you have a
replacement BRITA® MAXTRA water filter
cartridge available.
Please note that on average it will take 5½
minutes to filter 1 litre of water through the
BRITA® MAXTRA cartridge.
Using the Memo function
It is important to change your filter cartridge
regularly to enjoy the benefits of filtered
water.
(See figure 4).
The BRITA® Memo system automatically
reminds you when your filter cartridge needs
to be changed. It is automatically calibrated
according to average use of one litre of water
per day and will remind you to change your
filter every 8 weeks. If you are a heavier user
than one litre per day you will need to change
your filter more often according to your usage
rate. A filter will effectively filter 150 litres of
water before needing replacement.
%
100
75
50
25
Figure 4
• After 8 weeks, all four bars will disappear
and a flashing arrow will appear to indicate
that the cartridge should be replaced.
(See figure 5).
Once you have fitted and prepared your filter
cartridge as outlined on page 5, start the
Memo system as follows:
• Press and hold the Start button until 4
bars appear on the display and flash twice.
The Memo is now set. The flashing dot in
the corner of the display indicates that the
Memo is working. (See figure 3).
Note: Repeat the cartridge preparation process
each time you insert a new cartridge.
%
100
75
50
25
Figure 5
Wash and dry the filter funnel, insert a new
cartridge (see 'Preparing the filter cartridge
for use') and restart the BRITA® Memo as
described above.
%
100
75
50
25
Note: The Memo system is only intended to
be used with BRITA® filter cartridges.
Figure 3
6
Using your Water Filter & Chiller (continued)
• The cartridge may be disposed of in
household waste or contact the BRITA®
consumer service for advice on recycling
schemes. Refer to page 8 for contact
details.
• Always ensure that you have spare BRITA®
MAXTRA cartridges available.
For more information on where to purchase
BRITA replacement filters please visit
You can also reach BRITA by email:
[email protected] or call BRITA Customer
Service in Australia on 1300 557 762 or in
New Zealand on 0800 4 BRITA/0800 437 82.
7
Care and Cleaning
• Do not use harsh detergents or abrasive
cleaners.
• Do not place any part of this appliance in a
dishwasher.
• Wipe the base with a clean cloth or paper
towel.
• Wash the filtering tank in warm, soapy
water using a mild detergent.
Emptying the internal tank
• Switch off the appliance and unplug from
the mains.
• Remove the lid and the filtering tank and
any water in the filtered water tank.
• Turn the appliance upside down to reveal
a drain plug located in the centre of the
base. (See figure 6).
• Wipe the inside of the filtered water tank
with a damp cloth which has been soaked
in water.
• Do not immerse the base in water or any
other liquid.
• If the unit is to be moved or stored for a
prolonged period of time without being
used, we recommend that you drain the
internal tank of any water. Flush the unit
as described on page 4 before using again.
Figure 6
• Using a coin or a suitable screw driver,
turn the plug anti clockwise until it is fully
loosened. Please note that it cannot be
completely removed.
• Drain the tank.
• Insert the plug after draining and using
a coin or suitable screwdriver, turn it
clockwise until it stops.
• Do not over tighten as this may damage
the plug.
Help Line
If you have any additional questions about using the Water Filter & Chiller, please call the
Sunbeam help line in Australia on 1300 881 861. In New Zealand, please call 0800 786 232.
For BRITA® filter cartridge and Memo enquiries, contact BRITA® Customer Care.
In Australia please call 1300 557 762. In New Zealand, please call 0800 427 482.
8
Notes
Notes
Notes
Notes
12 Month Warranty
This Sunbeam product is covered by a 12 month replacement or repair
warranty, which is in addition to your rights under the Australian Consumer
Law (if your product was purchased in Australia) or New Zealand Consumer
Guarantees Act (if your product was purchased in New Zealand).
Should you experience any difficulties with your
product during the warranty period, please contact
our customer service line for advice on 1300 881 861
in Australia, or 0800 786 232 in New Zealand.
Your warranty does not:
• cover freight or any other costs incurred in
making a claim, consumable items, accessories
that by their nature and limited lifespan require
periodic renewal (such as filters and seals) or any
consequential loss or damage; or
Alternatively, you can send a written claim to
Sunbeam to:
• cover damage caused by:
-
power surges, power dips, voltage supply problems,
or use of the product on incorrect voltage;
Australia
Units 5 & 6, 13 Lord Street
-
servicing or modification of the product other than
by Sunbeam or an authorised Sunbeam service
centre;
Botany NSW 2019 Australia
New Zealand
26 Vestey Drive
-
-
use of the product with other accessories,
attachments, product supplies, parts or devices
that do not conform to Sunbeam specifications; or
Mt Wellington, Auckland New Zealand
exposure of the product to abnormally corrosive
conditions; or
Upon receipt of your claim, Sunbeam will seek to
resolve your difficulties or, if the product is defective,
advise you on how to obtain a replacement or refund.
• extend beyond 3 months if the product is used
in commercial, industrial, educational or rental
applications.
To assist us in managing warranty claims, we
recommend you register your product as soon as
practicable after purchase by creating a MySunbeam
account on our website and send a copy of your
original receipt to Sunbeam.
The benefits given to you by our warranty are in addition
to other rights and remedies under law in relation to the
product.
In Australia our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure
and for compensation for any other foreseeable loss or
damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
In order to make a claim under our warranty, you must
have the original proof of purchase documentation for
the product and present it when requested .
Should your product develop any defect within
12 months of purchase because of faulty materials
or workmanship, we will replace or repair it, at our
discretion, free of charge. A product presented for
repair may be replaced by a refurbished product
of the same type rather than being repaired.
Our goods also come with guarantees that cannot be
excluded under the New Zealand Consumer Guarantees
Act.
If your warranty claim is not accepted, we will inform
you and if requested to do so by you, repair the
product provided you pay the usual charges for such
repair. You will also be responsible for all freight and
other costs.
Refurbished parts may be used to repair the product.
Our replacement or repair warranty only applies
where a defect arises as a result of faulty material
or workmanship during the warranty period. Your
warranty does not cover misuse or negligent handling
(including damage caused by failing to use the
product in accordance with this instruction booklet),
accidental damage, or normal wear and tear.
Should your product require repair or service after the
warranty period, contact your nearest Sunbeam service
centre. For a complete list of Sunbeam’s service
centres, visit our website or call our customer service
line for advice on 1300 881 861 in Australia,
or 0800 786 232 in New Zealand.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Brita’ is a registered trademark.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2013.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
9/13
|