Ultura Irons
Instruction Booklet
This book covers the use and care of the following Ultura Irons:
SR5990 Ultura 90 Resilium®
SR5880 Ultura 80 Stainless
SR5770 Ultura 70 Platinum
SR5665 Ultura 65 Platinum
SR5560 Ultura 60 Platinum
Shot & Spray Iron with Safety Auto-Off
Shot & Spray Iron with Safety Auto-Off
Shot & Spray Iron with Safety Auto-Off
Shot & Spray Iron with Safety Auto-Off
Shot & Spray Iron with Safety Auto-Off
Please read these instructions carefully
and retain for future reference.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR IRON
• Do not leave a hot iron within reach of
children. If they come into contact with a
hot iron it could lead to serious burns.
• Iron only on an ironing board.
• An iron takes approximately 30 minutes to
cool down. Allow the iron to cool completely
before storing.
• Do not leave the iron unattended while it is
plugged into the power outlet.
• Always unplug the iron from the power outlet
before filling or emptying the water tank.
• The iron must be used and rested on a stable
surface.
• The iron is not to be used if it has been
dropped, if there are visible signs of
damage or if it is leaking.
• Do not wind the cord around the soleplate
while the iron is still hot.
Sunbeam is very safety conscious when
designing and manufacturing consumer
products, but it is essential that the product user
also exercise care when using an electrical
appliance. Listed below are precautions which
are essential for the safe use of an electrical
appliance:
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Read carefully and save all the instructions
provided with an appliance.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and before
cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
If you have any concerns regarding the performance and use of your appliance,
Ensure the above safety precautions are understood.
3
Features of your Sunbeam
Ultura Iron
Powerful shot of steam
Pressing the shot of steam button instantly produces
a powerful shot of steam to remove stubborn wrinkles.
Vertical shot of steam
Pressing the shot of steam button with the iron in
an upright position produces a vertical shot of steam,
which is ideal for steaming curtains and suits, and
removing creases from delicate fabrics.
Fine spray mist
Pressing the spray button provides a fine mist spray
to dampen hard-to-iron fabrics.
Water inlet
The wide water inlet allows for easy filling and
features a rubber seal to prevent spilling.
Extra large, easy-fill water tank
Holds up to 280mL of water for continual
high steam performance, without having
to refill the tank regularly.
Maximum water level indicator
Indicates the maximum water level when
the iron is in the upright position.
Full length button groove
For ironing around buttons.
Resilium® non-scratch soleplate (SR5990)
Resilium® is a durable, scratch resistant surface that
provides a superior glide and prevents rucking. Exclusive
to Sunbeam, this premium soleplate features 98 steam
holes to maximise steam distribution.
2400W Fast heat up
(SR5990, SR5880 & SR5770)
Stainless steel soleplate (SR5880)
Provides faster initial heat up and rapid heat
recovery during ironing. The 2400 watt element
better maintains your selected temperature,
and provides superior shot of steam output.
Sleek and smooth, stainless steel is an excellent heat
conductor and is extremely durable and hard wearing.
It features a quality polished finish that is easy to clean
and care for.
®
Teflon Platinum Pro non-stick soleplate
(SR5770, SR5665 & SR5560)
Teflon® Platinum Pro is DuPont’s premium non-stick
coating. It glides easily across all types of fabric and
prevents sticking. This hard wearing surface consists of a
unique three coat system for superior durability and scratch
resistance. It simply wipes clean for fuss free maintenance.
4
Variable steam
The six-position steam dial allows you to select the
desired steam output for each garment. Alternatively,
select the DRY setting to iron without steam.
Safety auto-off
The iron automatically switches itself off if left in the
ironing position (horizontal) for 30 seconds, or in the
heel rest position (vertical) for 15 minutes.
(For more information on the safety
auto off feature see page 7).
Removable steam valve
The steam valve is connected to the steam dial,
and is removable to allow for easy cleaning.
Cleaning it regularly removes scale build-up
that can affect its performance.
(For instructions on how to clean the
steam valve see the care and
cleaning section on page 8).
Soft grip handle
The soft rubber grip handle allows for increased
comfort during ironing.
Extra long cord with 360º cord outlet
The 360 degree cord outlet allows free movement of
the cord in any direction for greater manoeuvrability
when ironing. The flexible grommet protects the cord
from fraying.
Power ON light
Illuminates to indicate that the iron is connected
to the power outlet and the power is turned on. The
power ON light doubles as the steam dial indicator.
Temperature indicator light
Align the desired setting with the temperature
indicator light.
Boost light
Illuminates to indicate that the iron is heating
and goes out when it has reached the temperature
selected on the temperature dial. The boost light
cycles on and off during ironing as the iron
maintains the selected temperature.
Stable heel rest
Extra large heel rest keeps the iron stable on the
ironing board.
Figure 1
Cord wrap facility
Temperature dial
The built-in cord wrap facility allows you to wind the
cord around the heel for neat and tidy storage of the
cord when the iron is not in use.
Allows you to select the desired temperature for
each garment. The adjustable temperature dial
also indicates the amount of steam recommended
for use on each temperature setting.
Drip-stop steam system
The drip-stop steam system automatically stops water
flowing to the steam chamber should the temperature
fall too low to generate steam. This prevents dripping,
even at low temperatures.
Using your Sunbeam Ultura Iron
Before first use
Using your iron
Remove any adhesive stickers, plastic covers
or cardboard sleeves from the soleplate.
Ensure that all adhesive is removed by
rubbing the soleplate with a cloth
dampened with methylated spirits.
Fill the water tank and empty the water. This
will rinse out any foreign particles remaining
in the water tank from the manufacturing
process.
NOTE: When turned on for the first time,
your new iron may give off vapours for up
to 10 minutes. This is due to the initial
heating of the materials used. It is safe, not
detrimental to the performance of the iron,
and will not reoccur.
1.Insert the 3 pin plug into a 230/240 volt
power outlet and turn the power on. The
power ON light (positioned on top of the
handle) will illuminate to indicate that the
iron is switched on and heating.
2.Turn the temperature dial to the desired
setting by aligning the setting on the dial
with the temperature indicator light. The
boost light will illuminate to indicate
that the iron is heating to the selected
temperature. When the boost light goes
out the iron has reached the selected
temperature and is ready to use.
NOTE: When the temperature dial is changed
from a high setting to a lower temperature
setting during ironing, the boost light will go
out immediately. This indicates that the iron
is cooling to the selected temperature. To
ensure that the iron has reached the selected
temperature and is not too hot, wait until the
boost light comes on again and then goes out
before ironing.
Filling the iron with water
Before filling the iron with water ensure the
power is turned off and the plug is removed
from the power outlet. The iron can be filled
with water while it is hot.
1.Turn the STEAM/DRY dial to DRY.
2.Place the iron on its heel and open the
water inlet cover.
Dry ironing
Follow steps 1 and 2 above.
3.Select DRY on the STEAM/DRY dial.
This will cut off the steam flow if there
is water in the tank.
3.Slowly pour water into the water inlet until
the maximum water level is reached. Do not
exceed the maximum water level indicator.
Push the water inlet cover firmly to close.
NOTE: The special soleplate design allows you
to use tap water with your Ultura iron without
affecting the steam performance. However in
very hard water areas, Sunbeam recommends
the use of distilled water, or water which has
been demineralised.
Steam ironing
Follow steps 1 and 2 above.
NOTE: When steam ironing, ensure that the
temperature dial is set to any temperature
within the steam band, and that the tank
is at least 1/4 full of water.
For best performance, we recommend the
use of Sunbeam Water Demineraliser, available
from Sunbeam Service Centres and selected
retailers. This will produce up to 30 litres of
demineralised water.
Do not fill the iron with fabric conditioner,
starches or any other solution as these will
damage the steam mechanism. Do not use
contaminated water.
4.Turn the STEAM/DRY dial to the desired
steam setting.
For best results, select the steam setting
that corresponds to the selected temperature,
as indicated on the temperature dial.
6
Using your Sunbeam Ultura Iron (continued)
Using the shot of steam
Using the spray mist
The shot of steam can be used when dry
or steam ironing, when the temperature dial
is set to any temperature within the steam
The spray mist can be used whether dry or
steam ironing to pre-dampen hard to iron
fabrics.
band or above the two dot ( ) setting.
1.Ensure the tank is at least 1/4 full of
water.
2.Select the desired temperature and wait
until the boost light goes out.
••
1.Ensure the tank is at least 1/4 full of
water.
2.Press the spray button during ironing to
release a fine mist from the spray nozzle.
3.Press the shot of steam button several
times with the iron on the soleplate to
prime the pump.
Note: If the tank has run dry, it may be
necessary to re-prime the pump after filling
the iron with water.
The safety auto-off feature
The safety auto-off mechanism automatically
turns the iron off if you forget.
The iron will automatically shut off if left
on the heel rest (vertical) for 15 minutes,
or in the ironing position (horizontal) for 30
seconds, without being moved.(See figure 2).
After the iron has cut-out, the power ON light
will remain illuminated, as the iron is still
connected to the power outlet. Once the iron
is moved, the power will reconnect. Allow the
iron to heat until the boost light goes out,
and continue ironing as normal.
The safety auto-off light on the handle will
illuminate and a warning beep will sound
to let you know that you have left the iron
unattended.
NOTE: Ultura models SR5665 and SR5560
will not produce a warning beep. The Safety
auto-off light on the handle will illuminate
to indicate that the auto-off function has
activated.
15 minutes
Figure 2
30 seconds
7
Care and Cleaning
After each use
Cleaning the steam holes
1 Turn the STEAM/DRY dial to DRY.
2 Turn the power off and remove the plug
from the power outlet.
3 Empty any remaining water from the
water tank.
To remove build up from the steam holes
which may affect steam performance,
use a cotton wool tip moistened in
methylated spirits.
Cleaning the Resilium® soleplate (SR5990)
4 Allow the iron to cool before winding
the cord around the built-in cord wrap.
Storage
Always store the iron on its heel rest.
NOTE: Do not store the iron with the
soleplate facing down, or in the carton.
Wipe with a soft damp cloth and wipe dry.
Cleaning the Stainless Steel soleplate
(SR5880)
Using a stainless steel or metal cleaner,
rub gently with a damp cloth and wipe dry.
Cleaning the Teflon® Platinum Pro
non-stick soleplate
(SR5770, SR5665 & SR5560)
The non-stick coating reduces sticking
of fabrics and starches to the soleplate.
Do not iron over sharp objects such as
buttons, studs and zippers, as these will
scratch the surface.
Figure 3
Wipe the soleplate with a damp soft cloth
after each use. If polyester has burnt to the
soleplate, iron a damp cotton cloth while hot.
Cleaning
To clean the exterior of your iron, wipe
over with a damp soft cloth and wipe dry.
Caution: Do not use scouring pads, abrasives
or harsh cleaners to clean your Resilium®,
Teflon® Platinum Pro, Teflon® Select or
Stainless steel soleplate, as these will
scratch and damage the surface.
Caution: Do not use harsh abrasives,
chemical cleaners or solvents to clean the
exterior of your iron as these will damage the
surface.
Cleaning the removable steam valve
To remove the steam valve, turn the STEAM/
DRY dial to clean, so that the steam valve
pops up. Gently scrub the tip of the valve
with a steel wool soap pad moistened in
warm water. Rinse and dry with a clean
cloth. Replace the steam valve and turn
clockwise to lock into position.
8
Ultura Ironing Tips and Tricks
Tip # 27 - Iron shirts like a pro
Tip # 13 - Ironing the seam
Start with the collar, working from the outer
edges into the middle. Iron the shoulder
next, followed by the cuffs and sleeves.
Place the collar at the narrow end of the
board so that one front panel of the shirt
is extended flat. Iron the front panel from
shoulder to shirt tail. Rotate to iron the
back of the shirt. Rotate and complete the
remaining front panel.
Always press seams in the same direction
they were made. When a garment is
produced, the fibres will naturally settle
in the direction they were initially pressed,
so it’s best not to iron against the grain.
Tip # 26 - Sort types of fabric
Sort articles to be ironed according to the
type of fabric. This will reduce the need to
adjust the temperature constantly. Start with
articles requiring lower temperatures and
work your way through to items requiring
higher settings.
Tip # 34 - Tips for T-shirts
Straighten seams on t-shirts before hanging
out to dry. To avoid damage to printed
graphics and logos turn the t-shirt inside out
and iron the reverse side of the print. Never
iron areas of your t-shirt where perspiration
marks are visible as the heat of the iron will
permanently fix the stain.
Tip # 2 - Summer frocks and frills
Steam is the key when ironing delicate
summer fabrics such as muslin, cotton and
linen. Don’t press down with the iron, simply
hover above the garment and steam it using
a vertical shot of steam. Ruffling, netting,
tulle or intricate hand detailing is also best
ironed using this method.
Tip # 54 - Hung out to dry
When washing is complete, remove shirts
from the machine immediately, shake them
out and hang them on coat hangers to air dry
– this will keep wrinkles to a minimum.
Tip # 5 - Pressing your winter woollies
Steam is crucial when pressing your winter
woollies. Woollen garments can be hung and
steamed using the vertical shot of steam
feature. After steaming, brush the garment
with your hand to plump up woollen fibres.
If ironing the garment flat it is best to use
a pressing cloth. Don’t be afraid to apply
pressure – steam and hold.
Tip # 18 - Selecting the right temperature
If you are unsure of the correct setting for a
particular garment, test a small area such as
a seam or inside hem before ironing a visible
area. Start with a low temperature and slowly
increase the heat to find the best setting.
Tip # 33 - Don’t be afraid to iron silk
Tip # 42 - Table settings to impress
To avoid unwanted creases always iron
your table cloth after taking it out of the
cupboard. A dinner party is a special
occasion, so treat the table cloth as you
would your own outfit. For best results, lay
towels across your table and iron the table
cloth over the towels. This will save you time
and ensure a beautifully presented table
setting.
Don’t be afraid to iron silk. Although delicate
in appearance, silk is the strongest and most
resilient of all natural fibres. To achieve the
best results, set to a low cotton setting and
use regular shots of steam. Always use a
pressing cloth to avoid shine marks.
9
Ironing Chart
FABRIC
TEMPERATURE SETTING
IRONING RECOMMENDATION
Acrylic
•
•
Dry iron on wrong side.
Acetate
Dry iron on wrong side while still damp or use
spray to dampen.
Nylon
•
•
Iron on wrong side while still damp or use spray
to dampen.
Polyester
Iron on wrong side while still damp or use spray
to dampen.
Rayon
•
•
Iron on wrong side of fabric.
Viscose
Mainly dry iron. Steam can be used under
manufacturer’s instructions.
Silk
••
••
••
••
Iron on wrong side. Use an ironing cloth to
prevent shine marks.
Wool
Steam iron on wrong side or use an ironing
cloth.
Wool Blends
Cotton Blends
Steam iron on wrong side or use an ironing
cloth.
Check label and follow manufacturer’s
instructions. Use setting for the fibre requiring
the lowest setting.
Corduroy
Cotton
•••
•••
Steam iron on wrong side or use an ironing
cloth and brush to raise the pile.
Dry iron while still damp or use spray to
dampen.
Use steam medium to high.
Linen
••• To MAX
Iron on wrong side or use an ironing cloth
to prevent shine marks, especially with dark
colours.
Dry iron while still damp or use spray to
dampen.
Use steam medium to high.
Denim
••• To MAX
Use maximum steam.
10
2 Year Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 2 years of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 2 Year Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 2 Year Replacement Guarantee
does not cover freight or any other costs
incurred in making a claim. Please retain
your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Ultura’ and ‘Resilium’ are registered trademarks
of Sunbeam Corporation.
‘Teflon’ is a registered trademark of DuPont.
Designed and engineered in Australia
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 1999, 2002, 2007.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
8/11
|