Spectra Logic Computer Hardware T50E User Manual

Spectra T50e  
Quick Start Guide  
Documentation  
Power cord  
Ethernet cable  
Rubber feet  
Half Height (HH) tape drive sled* -or- Full Height (FH) tape drive sled*  
Rack-mount kit  
1
Documentation  
Open This First  
Unpack and  
Verify the  
Components  
USB drive  
(in kit)  
* The tape drives, the (optional) redundant power supply, and the  
library may ship and arrive separately.  
Rack-mount Installation Refer to the Spectra T50e Rack-mount Kit Installation Instructions supplied in the Spectra T50e Documentation Kit.  
Tabletop Installation You do not need to remove the brackets.  
Important! If you remove the bracket, replace the  
black screw; do not replace the silver screw.  
Warning! The library weighs approximately 34.4 lb. Two people are  
needed to move or lift the library.  
German: Die Bebliothek hat ein Gewicht vonungefähr 15,6 kg. Zwei  
Personen ind notwendig, zu verschieben oder Aufhebung der Bibliothek.  
1
Do not set  
the library on  
the bracket.  
Install the  
Library  
Important! Lift the library only by the two sides—not by the front and back.  
Do not stack items on top of the library, as they can restrict robot movement.  
Alignment  
mark (6x)  
Bottom of library  
1. Carefully place the library on its side, but do not damage the bracket.  
2.Remove the paper backing from the six feet and install as shown.  
3. Place the library on a level surface in a well ventilated location.  
1
Access bottom  
Attach six feet  
2
Note: Do not install the feet if you are rack-mounting the library.  
Shipping Key Removal Follow these steps to remove the shipping key:  
1. Remove the tape securing the shipping key.  
Important! Lift  
only by two sides.  
Remove the  
Shipping  
Key  
2.Pull the key straight up and out of the library.  
1
Remove tape  
Remove key  
Replace tape  
3. Place the tape back over the opening in the top of the library.  
4.Store the key in the tab at the back of the library.  
2
3
L
4
Store key  
Tape Drive Installation Install the tape drives from bottom to top.  
1. Using a #2 Phillips screwdriver, remove the screws securing the cover plate  
1
Remove screws  
(or plates), as needed. Important! Do not leave openings uncovered.  
2
Install the  
Tape Drives  
2
Remove plate  
2.Remove the plate and store it and the screws for future use.  
4
3
2
(remove two plates  
for each full-height  
tape drive)  
3. Remove the tape drive from its protective packaging.  
4.While supporting the bottom of the drive sled, slide it into the  
empty drive bay. Push the drive sled in until it fits flush against  
the chassis and tighten the finger screws.  
3
4
Remove tape drive  
from packaging  
Install tape drive  
Note: Refer to the Spectra T50e Tape Drive Installation Instructions for  
additional information.  
Finger screws  
SCSI Follow these steps to connect SCSI tape drives.  
Important! Do not mix full-height and half-height tape drives in the  
library. Do not daisy-chain LTO-4 SCSI tape drives.  
SCSI  
Two half-height SCSI  
tape drives shown.  
1. Connect SCSI cables to the tape drives, as shown.  
2.Terminate as follows:  
2
1
Terminate  
ƒ LTO-3—terminate if it is the last device on the SCSI bus. Every  
connector on an LTO-3 tape drive must either be connected to a host,  
connected to the next tape drive, or terminated. A maximum of two  
LTO-3 SCSI tape drives can be daisy-chained on a single SCSI bus.  
Connect SCSI  
Connect the  
Cables  
3
Connect to Host  
ƒ LTO-4—terminate the second connector on every tape drive.  
Do not daisy-chain LTO-4 tape drives.  
3. Connect the other end of the cable to the host computer.  
Fibre Channel  
Fibre Channel Follow these steps to connect FC tape drives.  
1. Remove the protective plugs from the optical connector.  
1
Remove plugs  
2.Insert one end of the cable into the tape drive (either port).  
3. Connect the other end of the cable into the HBA or switch.  
Note: See the Spectra T50e Library User Guide for information about  
Power  
P
dual-port tape drives.  
Power Connect the power cord to the library and to an outlet.  
2
3
Connect FC  
Note: If you purchased an optional redundant power supply, refer to  
the Spectra T50e Power Supply Installation Instructions for  
information about installing it in the library.  
Connect to Host  
or switch  
Ethernet If you want to use the Ethernet option (remote management or  
email notification), connect the Ethernet cable to the library and to the host.  
Ethernet  
E
2009 Spectra Logic Corporation. All rights reserved worldwide. BlueScale, Spectra, SpectraGuard, TeraPack, and the Spectra Logic logo are registered trademarks of Spectra Logic Corporation.  
All other trademarks and registered trademarks are the property of their respective owners. Subject to change without notice.  
 
 

Sharp CRT Television LC 32FH500E User Manual
Sherwood DVD Player V 768 User Manual
Sony Radio XDR F1HD User Manual
Sony Speaker System SRSM30WHITE User Manual
Stiga Trimmer ST 1200 BAT User Manual
Sub Zero Refrigerator UC 24CI4 User Manual
Sunbeam Blender PB7600 User Manual
Sunbeam Fan HT38 User Manual
Sylvania Automobile A0171 User Manual
Sylvania DVD Player DVL1000 User Manual