RGB SQ PROCESSOR BOARD
HKSR-5803SQ
ADVANCED HQ PROCESSOR BOARD
HKSR-5803HQ
INSTALLATION MANUAL
1st Edition
Section 1
Installation
1-2. Installation Overview
Purpose of this manual
This manual is an installation manual of RGB SQ Proces-
sor Board HKSR-5803SQ and Advanced HQ Processor
Board HKSR-5803HQ.
This manual is intended for system and service engineers,
so describes information regarding installation.
Components
HKSR-5803SQ is composed of the following items:
. SQ-20 Board
. Hexagonal support 7 mm (4 pcs)
. PSW2.6 x 5.8 (8 pcs)
. Installation manual
Related manual
Besides this installation manual, the following manual is
available for HKSR-5803SQ and HKSR-5803HQ.
. Maintenance Manual (available on request)
This manual describes the information for the mainte-
nance of this unit and the information that premises the
parts level service.
HKSR-5803HQ is composed of the following items:
. DLP-27 Board
. Hexagonal support 7 mm (4 pcs)
. PSW2.6 x 5.8 (8 pcs)
. Installation manual
If this information is required, please contact your local
Sony Sales Office/Service Center.
Applicable models
SRW-5800
1-1. Specifications
Installations of HKSR-5803SQ or HKSR-5803HQ
The HKSR-5803SQ comprises the SQ-20 board.
Mount the SQ-20 board on the HPR-22 board.
General
HKSR-5803SQ
Dimensions (w/h)
The HKSR-5803HQ comprises the DLP-27 board.
Mount the DLP-27 board on the HPR-22 board.
SQ-20 Board: 155 x 90 mm
Mass
SQ-20 Board: approx. 70 g
Power requirements +3.3 V dc: 840 mA
Attach and adjust the HKSR-5803SQ or HKSR-5803HQ
properly, following the procedures in Section 1-3 and later.
+1.5 V dc: 1800 mA
Power consumption
approx. 5.5 W
HKSR-5803HQ
Dimensions (w/h)
DLP-27 Board: 155 x 90 mm
Mass
DLP-27 Board: approx. 70 g
Power requirements +3.3 V dc
+1.5 V dc:
850 mA
1800 mA
Power consumption
approx. 5.5 W
HKSR-5803SQ/5803HQ
1-1 (E)
1-3. Installation Procedure
4. Fully loosen the two fixing screws, and then remove
the upper lid (rear) assembly in the arrow direction.
1. Turn off the power of the VTR.
2. Fully loosen the two fixing screws, and then slide the
two knobs on the upper lid (front) assembly each to the
inside. (Move the knobs to the outside to fix the upper
lid (front) assembly.)
3. Remove the upper lid (front) assembly in the arrow
direction.
Fixing screw
Fixing screw
Upper lid (rear)
assembly
Protrusion
Square hole
Knob
Upper lid (front) assembly
Knob
Fixing screw
5. Raise the eject levers of the HPR-22 board in the
arrow direction, and then pull out the board slowly
upward.
Eject lever
HPR-22 board
Eject lever
Removal
Installation
HKSR-5803SQ/5803HQ
1-2 (E)
6. Remove the six screws to detach the shield plate from
the HPR-22 board.
9. Reattach the shield plate to the HIF-22 board with six
screws.
Shield plate
Shield plate
PSW
2.6 x 6
PSW
2.6 x 6
PSW
2.6 x 6
PSW
2.6 x 6
PSW2.6 x 6
PSW2.6 x 6
HPR-22 board
HPR-22 board
7. Attach four 7 mm hexagonal supports (accessory) to
the HPR-22 board with four screws (accessory).
8. Connect the SQ-20 board or DLP-27 board to the
HPR-22 board and secure it with four screws (accesso-
ry).
PSW2.6 x 5.8
(Supplied accessory)
HPR-22 board
Hexagonal
supports (7 mm)
(Supplied
PSW2.6 x 5.8
(Supplied
accessory)
accessory)
PSW2.6 x 5.8
(Supplied
accessory)
Hexagonal
supports (7 mm)
(Supplied
PSW2.6 x 5.8
(Supplied
accessory)
accessory)
SQ-20 board
or
DLP-27 board
HKSR-5803SQ/5803HQ
1-3 (E)
10. Securely insert the HPR-22 board into the “HPR” slot
to tightly connect the board to the connector on the
motherboard, while pressing down the two eject
levers.
1-4. Confirming Identification of
Optional Board
Confirmation Procedure
Eject lever
1. On the HOME menu, press the DIAG button while
pressing the [SFT] (shift) key.
The MAINTENANCE INFORMATION menu
appears.
HPR-22 board
Eject lever
ROM
VER
MAINTENANCE INFORMATION DISPLAY
F1
F2
F3
OPERATION
1105HOURS[
238HOURS[
153HOURS[
4048TIMES[
1105H]
238H]
153H]
4048T]
ERR
LOG
DRUM RUNNING
TAPE HOURS
THREADING
F4
OPTION
INF
MAINTE
EXEC
EXIT
DIAG
ALT
F5
F6
F7
F8
F9 F10
2. Press [F5] (OPTION INF).
The OPTION INFORMATION menu appears.
OPTION INFO
SS
F1
OPTION BOARD INFORMATION
APR
HKSR-5001 Board –––––––––
F2
HKSR-5802 Board –––––––––
FC
HKSR-5803 Board INSTALLED (SQ)
F3
F4
DVP
HIF
MY
FUNC
INFO
EXIT
DIAG
HPR
HPR-22 board
EQ
ALT
F5
F6
F7
F8
F9 F10
<Top view>
3. Check that “INSTALLED (SQ)” (HKSR-5803SQ) or
“INSTALLED (HQ)” (HKSR-5803HQ) is displayed
for the HKSR-5803 board.
n
For more information on the maintenance mode, refer to
Section 3 of the VTR Maintenance Manual Volume 1.
HKSR-5803SQ/5803HQ
1-4 (E)
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen
Ausrüstung
ohne
ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
HKSR-5803SQ/5803HQ
HKSR-5803SQ (SY)
HKSR-5803HQ (SY) J, E
3-286-478-01
Printed in Japan
2007. 10 08
©2007
Sony Corporation
|