2-591-383-12(1)
Micro HI-FI
Component
System
Operating Instructions
CMT-GPZ7
CMT-GPZ6
©2005 Sony Corporation
Table of Contents
Which discs can you play
on this system?..................................5
Viewing information about the disc
in the display .................................. 24
Viewing the tuner information in the
display ............................................ 25
Listening to audio from a connected
component ...................................... 27
Recording audio from a connected
component ...................................... 27
Recording on a connected
component ...................................... 27
Recording your favorite CD tracks
on a tape..........................................20
3GB
Create your own ATRAC CDs
In addition to the usual audio CDs, you can play an original CD, called “ATRAC CD,” that you create
with the supplied software, SonicStage. Using SonicStage, about 30 audio CDs* can be recorded on
one CD-R or CD-RW. The following is a quick overview of how you listen to music on your ATRAC
CD.
Install SonicStage on your computer.
SonicStage is software that takes music downloaded from
audio CDs on your computer and creates original CDs. It
can be installed from the supplied CD-ROM.
ATRAC CD
Create an ATRAC CD.
After selecting your favorite songs from music
stored on your computer, record them on a CD-R/
CD-RW using SonicStage.
Audio CDs,
MP3 files
Listen to them with this system.
You can enjoy lots of songs on your original CD.
Please see the supplied “Installation/Operating Guide” for how to install SonicStage and how to create
ATRAC CDs.
* When the total playing time of one CD (album) is estimated at 60 minutes and you are recording on
a 700MB CD-R/CD-RW at 48 kbps in ATRAC3plus format.
4GB
Which discs can you play on this system?
Audio CDs:
CD-DA format CDs
CD-DA (Compact Disc Digital Audio) is a recording standard used for audio CDs.
ATRAC CDs:
CD-R/CD-RW on which audio data compressed in the ATRAC3plus format has
been recorded by using SonicStage*
ATRAC3plus (Adaptive Transform Acoustic Coding3plus) is audio compression technology
that satisfies the demand for high sound quality and high compression rates. ATRAC3plus can
compress audio files to about 1/20 of their original size at 64 kbps.
Bit rates and sampling frequencies this system can play are:
Bit rates
Sampling frequencies
44.1 kHz
ATRAC3
66/105/132 kbps
8 – 352 kbps
ATRAC3plus
44.1 kHz
Up to 62 characters can be displayed on this system.
MP3 CDs:
CD-R/CD-RW on which audio data compressed in the MP3 format has been
recorded by using a software other than SonicStage*
Bit rates and sampling frequencies this system can play are shown below. Variable Bit Rate
(VBR) files can also be played.
Bit rates
Sampling frequencies
32/44.1/48 kHz
MPEG-1 Layer3
MPEG-2 Layer3
MPEG-2.5 Layer3
32 – 320 kbps
8 – 160 kbps
8 – 160 kbps
16/22.05/23 kHz
8/11.025/12 kHz
This system conforms to Version 1.0/1.1/2.2/2.3/2.4 of the ID3 tag format. ID3 tag is a format
for adding certain information (track title, album name, artist name, etc.) to MP3 files. Up to
124 characters of ID3 tag information can be displayed on this system.
An ATRAC CD on which audio data compressed in the MP3 format has been recorded using software
other than SonicStage can also be played.
With SonicStage, you cannot create a CD on which mixed format audio data is recorded.
* Only ISO9660 Level 1/2 and Joliet extension format discs can be played.
continued
5GB
2)
Multi Session
List of playable discs
This is a recording method that enables adding of
data using the Track-At-Once method.
Conventional CDs begin at a CD control area called
the Lead-in and end at an area called Lead-out. A
Multi Session CD is a CD having multiple sessions,
with each segment from Lead-in to Lead-out
regarded as a single session.
Format of discs
Disc logo
Audio CDs
CD-R/CD-RW
(audio data, ATRAC3plus
files, MP3 files)
CD-Extra: This format records audio (audio CD
data) on the tracks in session 1 and data on the tracks
in session 2.
Mixed CD: This format records data on the first
track and audio (audio CD data) on the second and
subsequent tracks of a session.
Discs that this system cannot
play
Notes on CD-R and CD-RW
• Some CD-Rs or CD-RWs cannot be played
on this system depending upon the recording
quality or physical condition of the disc, or
the characteristics of the recording device.
Furthermore, the disc will not play if it has not
been correctly finalized. For more
information, see the operating instructions for
the recording device.
• CD-ROMs
• CD-Rs/CD-RWs other than those recorded in
the following formats:
– music CD format
– ATRAC3plus format and MP3 format that
conform to ISO96601) Level 1/Level 2,
Joliet or Multi Session2)
• Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this unit.
Attempting to do so may damage the unit. Do
not use such discs.
• A disc with paper or stickers on it.
• A disc that has the adhesive, cellophane tape,
or a sticker still left on it.
• Discs recorded on CD-R/CD-RW drives may
not be played back because of scratches, dirt,
recording condition or the driver’s
characteristics.
• CD-R and CD-RW discs recorded in multi-
session that have not ended by “closing the
session” are not supported.
• With formats other than ISO9660 Level 1 and
2, folder names or file names may not be
displayed correctly.
• The following discs take a longer time to start
playback.
• An 8 cm disc with an adaptor
1)
ISO9660 Format
The most common international standard for the
logical format of files and folders on a CD-ROM.
There are several specification levels. In Level 1,
file names must be in the 8.3 format (no more than
eight characters in the name, no more than three
characters in the extension) and in capital letters.
Folder names can be no longer than eight characters.
There can be no more than eight nested folder
levels. Level 2 specifications allow file names and
folder names up to 31 characters long. Each folder
can have up to 8 trees.
– a disc recorded with complicated tree
structure.
– a disc recorded in Multi Session.
– a disc to which data can be added (non-
finalized disc).
For Joliet in the expansion format (file and folder
names can have up to 64 characters) make sure of
the contents of the writing software, etc.
6GB
Music discs encoded with
copyright protection
technologies
About ATRAC CDs and
MP3 CDs
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
The structure of ATRAC CDs
and MP3 CDs
ATRAC CDs and MP3 CDs consist of “files”
and “groups.” A “file” is equivalent to a “track”
of an audio CD. A “group” is a bundle of files
and is equivalent to an “album.” For MP3 CDs,
this system recognizes an MP3 folder as a
“group” so that ATRAC CDs and MP3 CDs can
be operated in the same way.
Playing order of ATRAC CDs
and MP3 CDs
For ATRAC CDs, files are played in the order
selected in SonicStage. For MP3 CDs, the
playing order may differ depending on the
method used to record MP3 files on the disc. In
the following example, files are played in order
of 1 to 7.
Group
File
MP3 CD
(Maximum directory level: 8)
continued
7GB
The usable number of groups and
files
ATRAC CDs:
• Maximum number of groups: 255
• Maximum number of files: 999
MP3 CDs:
• Maximum number of groups: 256
• Maximum number of files: 511
(The maximum number of MP3 files and groups that
can be contained on a single disc is 512.)
Notes
• The system may be unable to play MP3 files that do
not have the “.MP3” extension.
• Attempting to play non-MP3 files that have the
“.MP3” extension may result in noise or malfunction.
• If ATRAC3plus files and MP3 files are recorded on
the same disc, this system plays the ATRAC3plus
files first.
• On a disc that has ATRAC3plus and MP3 files, do
not save files in other formats and do not make
unnecessary folders.
• To compress a source in an MP3 file, we recommend
setting the compression parameters to “44.1 kHz,”
“128 kbps,” and “Constant Bit Rate.”
• To record up to the maximum capacity, set the
writing software to “halting of writing.”
• To record to the maximum capacity at one time up on
media that has nothing recorded on it, set the writing
software to “Disc at Once.”
Cautions when playing a disc
that is recorded in Multi
Session
• If the disc begins with a CD-DA session, it is
recognized as a CD-DA (audio) disc, and
ATRAC3plus/MP3 sessions are not played
back.
• If the disc begins with an ATRAC3plus/MP3
session, it is recognized as an ATRAC CD/
MP3 CD, and CD-DA (audio) sessions are not
played back.
• The playback range of an MP3 CD is
determined by the tree structure of files
produced by analyzing of the disc.
• A disc with a mixed CD format will be
recognized as a CD-DA (audio) disc.
8GB
Getting Started
Hooking up the system
Perform the following procedures 1 to 4 to hook up your system using the supplied cords and
accessories.
Right speaker
Left speaker
3
4
1
2
AM loop aerial
FM lead aerial
1 Connect the speakers.
2 Connect the FM and AM aerials.
Connect the right and left speaker cords to
the SPEAKER terminals as shown below.
Set up the AM loop aerial, then connect it.
ANCE
IMPED
Ω
USE 6-16
Red (3)
3
Plug type A
L
#
AM loop aerial
#
R
Black (#)
Insert this portion
3
Extend the FM lead aerial
horizontally
continued
9GB
Plug type B
4 Connect the mains lead to mains.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).
To turn on the system, press ?/1.
AM loop aerial
Extend the FM lead aerial horizontally
Plug type C
AM loop aerial
North American models:
Connect using the white side
Extend the FM lead
aerial horizontally
Other models:
Connect using the brown
side
Note
To prevent noise pickup, keep the aerials away from
the speaker cords.
3 For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.
Refer to the print on your system’s
VOLTAGE SELECTOR for available
settings.
10GB
Inserting two R6 (size AA)
batteries into the remote
Setting the clock
Use buttons on the remote for the operation.
1
2
3
Press ?/1 to turn on the system.
Press CLOCK/TIMER SET.
Press . or > repeatedly to set the
hour.
4
5
Press ENTER.
Press . or > repeatedly to set the
minute.
Note
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
6
Press ENTER.
The clock starts working.
Tip
To adjust the clock
With normal use, the batteries should last for about six
months. When the remote no longer operates the
system, replace both batteries with new ones.
1 Press CLOCK/TIMER SET.
2 Press . or > repeatedly to select
“CLOCK SET”, then press ENTER.
When carrying this system
3 Do the same procedures as step 3 to 6
above.
Perform the following procedure to protect
the CD mechanism.
Note
Use buttons on the unit for the operation.
The clock is not displayed in Power Saving Mode
1 Press ?/1 to turn on the system, then
press FUNCTION repeatedly to switch
the function to CD.
2 Make sure that no disc is loaded in the
disc slot.
3 Hold down DISPLAY, and then press Z
and ML until “LOCK” appears.
4 Unplug the mains lead.
11GB
Playing a disc
— Normal Play/Shuffle Play
CD – Play
Loading a disc
Use buttons on the unit for the operation.
This system lets you play CDs in different play
modes.
Example: When playing a disc
1
2
Press CD (or FUNCTION repeatedly) to
switch the function to CD.
Insert a disc in the disc slot with the
label side up.
Z
Playing time
Track number
When you
play a disc,
insert it with
the label side
up.
1
2
Press CD (or FUNCTION repeatedly) to
switch the function to CD.
Press PLAY MODE repeatedly in stop
mode until the mode you want appears
in the display.
Notes
Select
To play
• When you turn on the system, the disc is not
pulled into the disc slot until “NO DISC”
appears in the display. Do not attempt to
push in the disc until “NO DISC” appears.
• Do not use a disc with tape, seals or paste on it as this
may cause malfunction.
No display
(Normal Play)
The tracks on the disc in
original order.
All the tracks in the group on
the ATRAC CD or MP3 CD
in original order.
(Normal Play)
• Do not load an 8 cm disc with an adaptor. Doing so
may cause the system to malfunction.
• When you remove a disc, handle the disc by its edge
and pull it straight out of the disc slot. Do not touch
the surface.
When playing an audio CD,
the system performs the
same operation as Normal
Play.
SHUF
(Shuffle Play)
All the tracks on the disc in
random order.
• If you load a disc that is not playable by this system,
it will be ejected automatically.
SHUF
(Shuffle Play)
All the tracks in the group on
the ATRAC CD or MP3 CD
in random order.
When playing an audio CD,
the system performs the
same operation as Shuffle
Play.
PGM
(Program Play)
The tracks on the disc in the
order you want them to be
played (see “Creating your
3
Press N (or CD NX on the unit).
12GB
Other operations
Searching for tracks with
the jog dial
To
Do this
Stop play
Pause
Press x (or CD x on the unit).
Press X (or CD NX on the unit).
Press again to resume play.
You can quickly search for and play the desired
track by using the jog dial on the unit.
Use buttons on the unit for the operation.
Select a track
Press . or > repeatedly.
Select a group on Press
the ATRAC CD step 2.
or MP3 CD
+ or – repeatedly after
1
2
Press FUNCTION repeatedly to switch
the function to CD.
Find a point in a Keep pressing m or M during
track
playback and release it at the
desired point.
Turn the jog dial in stop mode to select
the desired track, then press ENTER.
Remove a disc Press Z on the unit.
To search for tracks on the ATRAC CD or
MP3 CD, turn the jog dial to first select the
desired group, then press ENTER before
performing step 2.
Notes
• You cannot change the play mode during playback.
• Some time may be needed to start playback of discs
recorded in complex configurations such as many
layers.
Playback starts from the selected track.
Note
• Before playing back a track, the system reads all
tracks and groups on the disc. During this time,
“READING” appears on the display. Depending on
disc content, some time may be needed to read the
disc.
Only the first 6 characters are displayed when
performing the group or track search.
Tip
You can search for and play other tracks in the selected
group during playback. To select a track of another
group during playback, turn the jog dial
counterclockwise until “GROUP” appears, then press
ENTER to select a group. You can then select the
desired track by turning the jog dial.
• A group that does not include MP3 tracks is skipped.
• Depending on the encoding/writing software,
recording device or the recording media used at the
time an MP3 track is recorded, you may encounter
such problems as disabled playback, sound
interruptions and noise.
To cancel the track search
• When playing back an MP3 track, the playback
elapsed time indication may differ from the actual
time in the following cases.
Press CANCEL.
Notes
– When you play back a VBR (variable bit rate)
MP3 track
• If you do not perform any operations for
approximately 8 seconds, the display returns to the
previous one.
– When you perform fast forward or rewind (Manual
Search)
• The track search is not possible in Program Play
mode.
Tip
When disc access takes a long time, set “CD POWER”
13GB
Playing repeatedly
— Repeat Play
Creating your own
program
— Program Play
You can play all the tracks or a single track on a
disc repeatedly.
You can make a program of up to 25 steps.
You can synchro record the programmed tracks
Press REPEAT repeatedly during playback
until “REP” or “REP 1” appears.
REP: For all the tracks on the disc up to five
times.
REP 1: For a single track only.
Using the remote
1
2
3
Press CD (or FUNCTION repeatedly) to
switch the function to CD.
To cancel Repeat Play
Press REPEAT repeatedly until both “REP” and
“REP 1” disappear.
Press PLAY MODE repeatedly in stop
mode until “PGM” appears.
Note
Press . or > repeatedly until the
desired track number appears.
When you select “REP 1”, that track is repeated
endlessly until “REP 1” is canceled.
When programming the tracks on the
ATRAC CD or MP3 CD, press
+ or –
repeatedly to select the desired group, then
press . or > repeatedly until the
desired track number appears.
Selected track number
Total playing time
4
Press ENTER.
The track is programmed.
The program step number appears,
followed by the last programmed track
number and total playing time.
5
6
To program additonal tracks, repeat
steps 3 and 4.
Press N (or CD NX on the unit).
Program Play starts.
14GB
Other operations
Using the jog dial
To
Do this
Use buttons on the unit for the operation.
Cancel Program Play
Press PLAY MODE
repeatedly in stop mode
until “PGM” disappears.
1
2
3
Press FUNCTION repeatedly to switch
the function to CD.
Erase the program
Press CLEAR in stop
mode. Each time you press
the button, a track is cleared
from the end of the
program.
Press PLAY MODE repeatedly in stop
mode until “PGM” appears.
Turn the jog dial to select the desired
track.
Add a track to the end of Perform steps 3 and 4 in
To program tracks on the ATRAC CD or
MP3 CD, turn the jog dial to first select the
desired group, then press ENTER before
performing step 3.
the program
stop mode.
Note
You cannot erase the program during playback.
Tips
4
Press ENTER.
• You can program the tracks during playback by using
the jog dial.
The track is programmed.
The program step number appears,
followed by the last programmed track
number and total playing time.
• The program you made remains after Program Play
finishes. To play the same program again, press CD
(or FUNCTION repeatedly) to switch the function to
CD, then press N (or CD NX on the unit).
However, the program is cleared when you eject the
disc.
5
6
To program additional tracks, repeat
steps 3 and 4.
Press CD NX.
• “– –.– –” appears when the total program time
exceeds 100 minutes, or when you select a disc with
21 tracks or more, or when you select an
ATRAC3plus/MP3 track.
Program Play starts.
15GB
6
Press + or – (or TUNING + or – on the
unit) repeatedly to select the desired
preset number.
Tuner
7
8
Press ENTER.
Presetting radio stations
Repeat steps 4 through 7 to store other
stations.
You can preset up to 20 FM stations and 10 AM
stations. You can then tune in any of those
stations simply by selecting the corresponding
preset number.
Tip
Press x to stop scanning.
Manual tuning preset
Automatic tuning preset
You can manually tune in and store the radio
frequency of the desired stations.
You can automatically tune in all of the stations
that can be received in your area and then store
the radio frequency of the desired stations.
1
Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
1
Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
2
3
Press TUNER BAND repeatedly to
select “FM” or “AM”.
2
3
4
Press TUNER BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“AUTO” and “PRESET” disappear from
the display.
Press TUNING MODE repeatedly until
“AUTO” appears in the display.
4
Press + or – (or TUNING + or – on the
unit) repeatedly to tune in the desired
station.
Press + or – (or TUNING + or – on the
unit).
The frequency changes as the system scans
for a station. Scanning stops automatically
when a station is tuned in. At that time,
“TUNED” and “STEREO” (for an FM
stereo program only) appear.
5
6
Press TUNER MEMORY.
Press + or – (or TUNING + or – on the
unit) repeatedly to select the desired
preset number.
7
8
Press ENTER.
If “TUNED” does not appear and the
scanning does not stop
Repeat steps 4 through 7 to store other
stations.
Set the frequency of the desired radio
station as described in steps 3 and 4 of
Other operations
To
Do this
5
Press TUNER MEMORY.
Tune in a station
Follow the procedure described
The preset number flashes. Perform steps 6
and 7 while the preset number flashes.
Set another station After step 5, press + or – (or
to the existing
preset number
TUNING + or – on the unit)
repeatedly to select the preset
number of the station you want
to store.
Preset number
16GB
To change the AM tuning interval
(except for European model)
Listening to the radio
The AM tuning interval is factory-preset to
9 kHz (or 10 kHz for some areas). To change the
AM tuning interval, tune in any AM station first,
then turn off the system. While holding
ML, press ?/1 on the unit. When you
change the interval, all the AM preset stations
are erased. To reset the interval, repeat the same
procedure.
You can listen to a radio station either by
selecting a preset station, or by manually tuning
in the station.
Listening to a preset station
— Preset Tuning
Note
Preset radio stations in the tuner’s memory first
You cannot change the AM tuning interval in Power
1
Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
Tips
• The preset stations are retained for about half a day
even if you disconnect the mains lead or if a power
failure occurs.
2
3
4
Press TUNER BAND repeatedly to
select “FM” or “AM”.
• To improve broadcast reception, adjust the supplied
aerials, or connect a commercially available external
aerial.
Press TUNING MODE repeatedly until
“PRESET” appears in the display.
To improve tuner reception
Press + or – (or TUNING + or – on the
unit) repeatedly to select the desired
preset station.
When tuner reception is poor, set CD player
power off by CD power manage function.
CD power is factory set to on.
Use buttons on the unit for the operation.
1 Press FUNCTION repeatedly to switch the
function to CD.
2 Press ?/1 to turn off the system.
3 After “STANDBY” stops flashing, press ?/1
while holding CD x.
“CD POWER” and “OFF” appear.
To set CD power on
Repeat the procedure above and “CD POWER”
and “ON” appear.
Notes
• When “CD POWER” and “OFF” are selected, disc
access time is increased.
• You cannot change the setting in Power Saving
continued
17GB
Listening to non-preset radio
station
Using the Radio Data
System (RDS)
— Manual Tuning
(European model only)
1
Press TUNER BAND (or FUNCTION
repeatedly) to switch the function to
TUNER.
What is the Radio Data
System?
2
3
Press TUNER BAND repeatedly to
select “FM” or “AM”.
Radio Data System (RDS) is a broadcasting
service that allows radio stations to send
additional information along with the regular
program signal. RDS is available only on FM
stations.*
Press TUNING MODE repeatedly until
“AUTO” and “PRESET” disappear from
the display.
4
Press + or – (or TUNING + or – on the
unit) repeatedly to tune in the desired
station.
Note
RDS may not work properly if the station you are tuned
in is not transmitting the RDS signal properly or if the
signal is weak.
Note
When switching to CD function from tuner, a longer
time may be required to access the disc. In this case, set
“CD POWER” and “ON” by CD power manage
* Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not
familiar with the RDS system, check with your local
radio stations for details on RDS services in your
area.
Tips
• To improve broadcast reception, adjust the supplied
aerials, or connect a commercially available external
aerial.
Receiving RDS broadcasts
• When an FM stereo program has static noise, press
FM MODE repeatedly until “MONO” appears.
There will be no stereo effect, but the reception will
improve.
Simply select a station from the FM band.
When you tune in a station that provides RDS
services, the station name appears in the display.
• Press TUNING MODE repeatedly until “AUTO”
appears in step 3 above, then press + or – (or
TUNING + or – on the unit). The frequency
indication changes and scanning stops when the
system tunes in a station (Automatic Tuning).
• To record the radio programs, use manual recording
To check the RDS information
Each time you press DISPLAY, the display
changes cyclically as follows:
Station name1) t Preset number2) and
frequency t Clock display (for eight seconds)
t Bass level (for eight seconds) t Treble
level (for eight seconds)
1) If the RDS broadcast is not properly received, the
station name may not appear in the display.
2) Preset number is displayed only if you preset radio
18GB
Playing a tape
Tape – Play
You can use TYPE I (normal) tape.
Loading a tape
1
2
Load a tape.
1
Press Z PUSH OPEN/CLOSE on the
unit.
Press TAPE (or FUNCTION repeatedly)
to switch the function to TAPE.
2
Load a recorded/recordable tape into
the cassette holder.
3
Press N (or TAPE N on the unit).
Other operations
Note
To
Do this
Be careful not to touch the exposed tape.
Stop play
Pause
Press x (or TAPE x on the unit).
Press X. Press again to resume
play.
With the side
you want to
play/record
facing towards
you.
Fast-forward or
rewind
Press m or M.
Remove a tape
Press Z PUSH OPEN/CLOSE
on the unit in stop mode.
H
s
j
J
Note
Do not eject the tape during playback or recording, as
this may cause irreparable damage to the tape and
cassette holder.
19GB
Recording on a tape
manually
Tape – Recording
Recording your favorite
CD tracks on a tape
— Manual Recording
You can record just the portions you like from a
CD or radio program on a tape.
— CD-TAPE Synchro Recording
You can also record from connected
components (see “Hooking up optional
You can use TYPE I (normal) tape. The
recording level is adjusted automatically.
Use buttons on the unit for the operation.
Use buttons on the unit for the operation.
1
2
Load a recordable tape.
1
2
Load a recordable tape.
Press FUNCTION repeatedly to switch
the function to CD and load a disc you
want to record.
Press FUNCTION repeatedly to select
the desired source to record.
• CD: To record from this system’s CD
player.
• TUNER: To record from this system’s
tuner.
• MD: To record from the optional
component connected to the ANALOG
IN jack.
When you want to record a group from an
ATRAC CD or MP3 CD, be sure to press
PLAY MODE repeatedly to select , then
press
+ or – repeatedly to select the
desired group before proceeding.
3
4
Press CD SYNC.
“SYNC” and “REC” appear. The tape deck
stands by for recording and the CD player
pauses for playback.
3
4
Press z PAUSE/START.
“REC” lights up and the tape deck stands by
for recording.
Press z PAUSE/START.
Press z PAUSE/START, then start
playing the desired source to record.
Recording starts.
When the recording is completed, the CD
player and the tape deck stop automatically.
Recording starts.
Other operations
To stop recording
Press TAPE x (or CD x).
To
Do this
Stop recording
Pause recording
Press TAPE x.
Tip
Press z PAUSE/START.
If you stop the recording by pressing CD x, the tape
stops after making about a 4 seconds blank
(unrecorded) space before stopping.
Notes
• You cannot listen to other sources while recording.
• Recording stops if you change the function to another
one.
To record a disc by specifying
track order
You can record only your favorite CD tracks
using Program Play. Between steps 2 and 3,
perform steps 2 to 5 of “Creating your own
Tip
For recording from the tuner:
If noise is heard while recording from the tuner, move
the respective aerial to reduce the noise.
20GB
Sound Adjustment
Timer
Adjusting the sound
Falling asleep to music
— Sleep Timer
You can adjust the bass and treble to enjoy more
powerful sound.
You can set the system to turn off after a certain
time, so that you can fall asleep to music.
Generating a more dynamic
sound (Dynamic Sound
Generator X-tra)
Press SLEEP repeatedly.
Each time you press the button, the minute
display (the turn-off time) changes cyclically as
follows:
AUTO* t 90MIN t 80MIN t … t
10MIN t SLEEP OFF
Press DSGX on the unit.
Each time you press the button, the display
changes cyclically as follows:
*
* The system automatically turns off in 100 minutes or
after the current disc or tape finishes playing.
DSGX ON y DSGX OFF
* The DSGX indicator lights up.
Other operations
To
Press
Adjusting the bass and treble
Check the
remaining time*
SLEEP once.
You can adjust the bass and treble.
1
Press EQ repeatedly to select “BASS”
or “TREBLE”.
Change the time SLEEP repeatedly to select the
to turn off time you want.
Cancel the Sleep SLEEP repeatedly until “SLEEP
Timer function OFF” appears.
Each time you press the button, the display
changes as follows:
BASS y TREBLE
* You cannot check the remaining time if you select
“AUTO”.
2
Press . or > repeatedly to adjust
the level while “BASS” or “TREBLE”
appears.
Tip
You can use the Sleep Timer, even if you have not set
the clock.
To adjust the bass on the unit
Turn BASS control.
To adjust the treble on the unit
Turn TREBLE control.
To exit the bass and treble
settings
Press any button other than EQ, . or >.
Also if you do not perform any operations for a
few seconds, the display automatically returns to
the original display.
21GB
Other operations
Waking up to music
— Play Timer
To
Do this
Activate the timer/ 1 Press CLOCK/TIMER
check the setting
SELECT.
2 Press . or >
repeatedly until “PLAY
SEL” appears, then press
ENTER.
You can wake up to music at a preset time. Make
sure you have set the clock (see “Setting the
Use buttons on the remote for the operation.
Change the setting Start over from step 1.
1
Prepare the sound source you want to
play.
Cancel the timer
1 Press CLOCK/TIMER
SELECT.
• CD: Load a disc. To start from a specific
track, make a program (see “Creating
• TUNER: Tune in the preset radio station
2 Press . or >
repeatedly until “TIMER
OFF” appears, then press
ENTER.
Notes
• You cannot activate the Play Timer and the Rec
Timer at the same time.
• If you use the Play Timer and the Sleep Timer at the
same time, the Sleep Timer has priority.
• Do not operate the system from the time the system
turns on until the play starts (about 15 seconds before
the preset time).
2
Press VOLUME +/– to adjust the
volume.
3
4
Press CLOCK/TIMER SET.
• If the system is on about 15 seconds before the preset
time, the Play Timer will not be activated.
• You cannot use the optional component connected to
ANALOG IN jack as the sound source for Play
Timer.
Press . or > repeatedly to select
“PLAY SET”, then press ENTER.
“ON” appears and the hour indication
flashes.
5
Set the time to start playing.
• The Play Timer setting remains as long as the setting
is not canceled manually.
Press . or > repeatedly to set the
hour, then press ENTER.
The minute indication flashes.
Press . or > repeatedly to set the
minute, then press ENTER.
6
7
Set the time to stop playing following
the same procedure as step 5.
Press . or > repeatedly until the
desired sound source appears.
Each time you press the button, the display
changes cyclically as follows:
t
y
T
TUNER
CD PLAY
t
T
TAPE PLAY
8
9
Press ENTER.
The start time, the stop time and the sound
source appear in turn, then the original
display returns.
Press ?/1 to turn off the system.
22GB
Other operations
Timer recording radio
programs
To
Do this
Activate the timer/ 1 Press CLOCK/TIMER
check the setting
SELECT.
2 Press . or >
repeatedly until “REC SEL”
appears, then press ENTER.
— Rec Timer
You can record a preset radio station from a
specified time.
Change the setting Start over from step 1.
To timer record, you must first preset the radio
Cancel the timer
1 Press CLOCK/TIMER
SELECT.
2 Press . or >
repeatedly until “TIMER
OFF” appears, then press
ENTER.
1
Tune in the preset radio station (see
Notes
• You cannot activate the Play Timer and the Rec
Timer at the same time.
2
3
Press CLOCK/TIMER SET.
Press . or > repeatedly to select
“REC SET”, then press ENTER.
• If you use the Rec Timer and the Sleep Timer at the
same time, the Sleep Timer has priority.
• Do not operate the system from the time the system
turns on until the recording starts (about 15 seconds
before the preset time).
“ON” appears and the hour indication
flashes.
4
5
Set the time to start recording.
• If the system is on about 15 seconds before the preset
time, the Rec Timer will not be activated.
• The volume is reduced to minimum during
recording.
Press . or > repeatedly to set the
hour, then press ENTER.
The minute indication flashes.
Press . or > repeatedly to set the
minute, then press ENTER.
• The Rec Timer is canceled automatically after the
Rec Timer has been activated.
Set the time to stop recording following
the same procedure as step 4.
The start time, the stop time, and the preset
radio station to be recorded (e.g., “FM 5”)
appear in turn, before the original display
returns.
6
7
Load a recordable tape.
Press ?/1 to turn off the system.
23GB
Viewing information
about the disc in the
display
Display
Turning off the display
— Power Saving Mode
You can check the playing time and remaining
time of the current track or that of the disc.
When an ATRAC CD or MP3 CD is loaded, you
can also check the information recorded on disc,
such as the titles.
The clock display can be turned off to minimize
the amount of power consumed during standby
(Power Saving Mode).
Press DISPLAY repeatedly while the
system is off until the clock display
disappears.
Checking the remaining time
and titles
To cancel Power Saving Mode
Press DISPLAY while the system is off. Each
time you press the button, the display switches
cyclically as follows:
Clock display* t No display (Power Saving
Mode)
Press DISPLAY during Normal Play.
Each time you press the button, the display
changes cyclically as follows:
Current track number and elapsed playing time
t Current track number and remaining time or
“– –.– –”1) t Remaining time of the disc or
“– –.– –”2) t Track title (ATRAC CD and MP3
CD4) only) t Group name3)4) t Clock display
(for eight seconds) t Bass level (for eight
seconds) t Treble level (for eight seconds)
* The clock is displayed only if you set the clock.
Note
You cannot perform the following operations in Power
Saving Mode.
– setting the clock
1)
– changing the AM tuning interval (except for
European model)
For MP3 CDs
2)
“– –.– –” appears for ATRAC CDs, MP3 CDs or
– changing the CD power manage function
when the audio CD is in a play mode other than 1
DISC Play.
Tips
3)
For ATRAC CDs and MP3 CDs
• STANDBY indicator lights up even in Power Saving
Mode.
4)
When you play back a track with an ID3 tag ver. 1
or ver. 2, the ID3 tag information appears. The ID3
tag displays the track title, album name and artist
name information.
• The timer continues to operate in Power Saving
Mode.
Note
When fast forward or fast reverse is performed, elapsed
playing time and remaining time of the track may not
be displayed accurately.
24GB
Checking the total playing
time and titles
Viewing the tuner
information in the display
Press DISPLAY repeatedly in stop mode.
Each time you press the button, the display
changes cyclically as follows:
Press DISPLAY while listening to the radio.
Each time you press the button, the display
changes cyclically as follows:
Station name1) t Preset number2) and
frequency t Clock display (for eight seconds)
t Bass level (for eight seconds) t Treble
level (for eight seconds)
x Normal Play mode
TOC display1) or total group number of the disc2)
or total track number of the current group2) t
Volume label2) or group name2) t Clock
display (for eight seconds) t Bass level (for
eight seconds) t Treble level (for eight
seconds)
1) European model only
2) Preset number is displayed only if you preset radio
stations (page 16)
1) TOC = Table of Contents; displays total number of
tracks on the disc, and total playing time of the disc
2) For ATRAC CDs and MP3 CDs (group names or
volume label may not be displayed depending on the
play mode)
x Program Play mode
The last track number of the program and the
total playing time t Total track number of the
program t Volume label* t Clock display
t Bass level t Treble level
* For ATRAC CDs and MP3 CDs
25GB
Optional Components
Hooking up optional components
To enhance your system, you can connect optional components. Refer to the operating instructions
provided with each component.
H
s
j
J
+
/
1
s
lj JL
HS
A
From the audio output jacks of an
optional analog component
To the digital input jack of an
optional digital component
Optional analog component
Optional digital component
Notes
A ANALOG IN jack
• There is no digital audio output from this jack during
playback of ATRAC3plus/MP3 tracks.
Use audio cord (not supplied) to connect an
optional analog component (MiniDisc player/
recorder or Portable Audio player, etc.) to this
jack. You can then record or listen to the sound
from the component through this system.
• You cannot make a digital recording of a copy
guarded disc using a digital component connected to
this system. Also, playback may not be possible
depending on the connected component.
• Before connecting or disconnecting the audio cord
(not supplied), press VOLUME – repeatedly (or turn
the VOLUME control on the unit counterclockwise)
to turn down the volume.
B CD DIGITAL OUT jack
Use a digital optical cord (square, not supplied)
to connect an amplifier, MiniDisc player/
recorder or DAT deck with a digital optical input
jack. Sound is then output when the system
function is set to CD. If the jack is covered with
a cap, remove it before use.
26GB
Listening to audio from a
connected component
Recording on a connected
component
1
Connect the audio cord (not supplied).
1
Connect the digital optical cord.
2
Start recording with the connected
digital component (MiniDisc player/
recorder, etc.).
2
3
Press FUNCTION repeatedly until “MD”
appears.
Refer to the operating instructions provided
with the connected component.
Start playing the connected
component.
Note
You can digitally record from the discs only. However,
you cannot record from copy prohibited discs and
ATRAC3plus/MP3 tracks.
Recording audio from a
connected component
1
Connect audio cord (not supplied).
2
Start recording manually.
27GB
General
“– –:– –” appears in the display.
• A power interruption has occurred. Set the clock
again.
Troubleshooting
Problems and remedies
The clock setting/radio presetting/timer is
canceled.
• Redo the following:
Should you encounter a problem with your
system, do the following:
1 Make sure the mains lead and speaker
cords are correctly and firmly connected.
2 Find your problem in the troubleshooting
checklist below and take the indicated
corrective action.
There is no sound.
• Press VOLUME + or turn VOLUME control on
the unit clockwise.
If the problem persists after doing all of the
above, consult your nearest Sony dealer.
• Make sure the headphones are not connected.
• There is no audio output during Rec Timer.
When the STANDBY indicator
flashes
Sound comes from one channel, or
unbalanced left and right volume.
• Place the speakers as symmetrically as possible.
• Connect the supplied speakers.
Immediately unplug the mains lead and check
the following items.
• If your system has a voltage selector, is the
voltage selector set to the correct voltage?
Check the voltage for your region, then
make sure the voltage selector is set
correctly.
• Are the + and – speaker cords short-
circuited?
• Are you using the supplied speakers?
• Is anything blocking the ventilation holes
on the rear of the system?
There is severe hum or noise.
• Move the system away from the source of noise.
• Connect the system to a different mains.
• Install a noise filter (commercially available) to
the mains lead.
The timer cannot be set.
The timer does not function.
• Check the timer setting and set the correct time
Check all the above items and fix any
problems found. After STANDBY indicator
stops flashing, reconnect the mains lead and
turn on the system. If the indicator still
flashes, or if the cause of the problem cannot
be found even after checking all the above
items, consult your nearest Sony dealer.
The color irregularity on a TV screen persists.
• Turn off the TV set once, then turn it on after 15
to 30 minutes. If the color irregularity still
persists, place the speakers farther away from the
TV set.
28GB
The remote does not function.
• Remove the obstacle.
Tracks on the ATRAC CD or MP3 CD cannot be
played back.
• Recording was not performed according to the
ISO9660 Level 1 or Level 2 format, or Joliet in the
expansion format.
• Move the remote closer to the system.
• Point the remote at the system’s sensor.
• Replace the batteries (R6/size AA).
• Locate the system away from the fluorescent light.
• The MP3 file does not have the extension “.MP3”.
• The data is not stored in ATRAC3plus/MP3
format.
The system can not be turned on even though
you have pressed ?/1.
• Make sure the mains lead is connected to mains.
• Discs containing MP3 files other than MPEG 1, 2,
2.5 Audio Layer-3 files cannot be played.
Tracks on the ATRAC CD or MP3 CD take
longer to play back than others.
• After the system reads all tracks on the disc,
playback may take more time than usual if:
– the number of groups or tracks on the disc is
very large.
CD player
“LOCKED” appears.
• Contact your Sony dealer or local authorized Sony
service facility.
– the album and track organization structure is
very complex.
The disc does not eject.
• You cannot eject the disc during CD Synchro
Recording. Press CD x on the unit to cancel the
CD Synchro Recording, then press Z on the unit
to eject the disc.
Title information do not appear correctly.
• Use a disc that conforms with ISO9660 Level 1,
Level 2 or Joliet in the expansion format.
• The disc ID3 tag is not ver. 1 nor ver. 2.
• The characters that can be displayed by this
system are as follows:
• Consult your nearest Sony dealer.
Play does not start.
• Check whether a disc is loaded.
– Upper cases (A to Z)
– Numbers (0 to 9)
• Replace the disc.
– Symbols (’< > * + , – /@[\] _ `)
• Load the disc correctly.
Other characters may not be displayed correctly.
• Load the disc with the label side up.
• Remove the disc and wipe away the moisture on
the disc, then leave the system turned on for a few
hours until the moisture evaporates.
• Press N (or CD NX on the unit) to start play.
Disc access takes a long time.
• Set “CD POWER” and “ON” by CD power
The sound skips.
• Replace the disc.
• Try moving the system to a place without
vibration (e.g., on top of a stable stand).
• Try moving the speakers away from the system, or
placing them on separate stands. When you listen
to a track with bass sounds at high volume, the
speaker vibration may cause the sound to skip.
Play does not start from the first track.
• Press PLAY MODE repeatedly until both “PGM”
and “SHUF” disappear to return to Normal Play.
continued
29GB
Tuner
The tape does not record.
• No cassette is loaded. Load a cassette.
• The tab has been removed from the cassette.
Cover the broken tab with adhesive tape
Severe hum or noise/stations cannot be
received.
• Find a place and an orientation that provide good
reception, then set up the aerial again. If you
cannot obtain good reception, we recommend you
connect a commercially available external aerial.
• The supplied FM lead aerial receives signals
along its entire length, so make sure you extend it
fully.
• The tape has wound to the end.
Optional components
There is no sound.
• Refer to General item “There is no sound.”
(page 28) and check the condition of the system.
checking:
• Locate the aerials as far away from the speaker
cords as possible.
• Consult your nearest Sony dealer if the supplied
AM aerial has come off the plastic stand.
• Try turning off surrounding electrical equipment.
• Set “CD POWER” and “OFF” by CD power
– if the cords are connected properly.
– if the cord plugs are firmly inserted all the way.
• Turn on the connected component.
• Refer to the operating instructions supplied with
the connected component and start playing.
• Press FUNCTION repeatedly to select “MD”
A stereo FM program cannot be received in
stereo.
• Press FM MODE until “STEREO” appears in the
display.
The sound is distorted.
• Set the volume of the connected component
lower.
Tape deck
If the system still does not
operate properly after performing
the above measures, reset the
system as follows:
The tape does not record or play, or there is a
decrease in sound level.
• The record/playback heads are magnetized.
Use buttons on the unit for the operation.
The tape does not erase completely.
• The record/playback heads are magnetized.
1 Disconnect the mains lead.
2 Reconnect the mains lead.
3 Press ?/1 to turn on the system.
4 Press CD x, DISPLAY and ?/1.
The system is reset to the factory settings. You
should set the settings you made, such as the
preset stations, clock, and timer.
There is excessive wow or flutter, or the sound
drops out.
• The capstans in the tape deck are dirty. Clean
Noise increases or the high frequencies are
erased.
• The record/playback heads are magnetized.
30GB
Messages
One of the following messages may appear or
flash in the display during operation.
CD
NO DISC
There is no disc in the player.
NO STEP
All of the programmed tracks have been erased.
CD OVER
You have reached the end of the disc while pressing
M during playback or pause.
PUSH STOP
You pressed PLAY MODE during playback.
STEP FULL
You tried to program 25 or more tracks (steps).
Tuner
COMPLETE
The preset operation ended normally.
Tape
NO TAB
You cannot record the tape because the tab has been
removed from the cassette.
NO TAPE
There is no tape in the tape deck.
Timer
PUSH SELECT
You tried to set the clock or timer during timer
operation.
SET CLOCK
You tried to select the timer when the clock is not
set.
SET TIMER
You tried to select the timer when the Play Timer or
Rec Timer are not set.
TIME NG
The Play Timer or Rec Timer start and end times are
set to the same time.
31GB
On the speaker system
This speaker system is not magnetically shielded and
the picture on TV sets may become magnetically
distorted. In such a case, turn off the power of the TV
set once, and after 15 to 30 minutes turn it on again.
If there seems to be no improvement, locate the
speaker system further away from the TV set.
Additional Information
Precautions
On operating voltage
Before operating the system, check that the operating
voltage of your system is identical with the voltage of
your local power supply.
On operation
• If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not operate
properly. Remove the disc and leave the system
turned on for about an hour until the moisture
evaporates.
On safety
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Unplug the system from the wall outlet (mains) if it
is not to be used for an extended period of time. To
disconnect the power cord (mains lead), pull it out by
the plug. Never pull the cord itself.
• When you move the system, take out any disc.
If you have any questions or problems concerning your
system, please consult your nearest Sony dealer.
• Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.
Notes on discs
• Before playing, clean the disc with a cleaning cloth.
• AC power cord must be changed only at the qualified
service shop.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
On placement
• Do not place the system in an inclined position.
• Do not place the system in locations where it is;
– Extremely hot or cold
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
– Dusty or dirty
• Do not use discs encircled with a protection ring.
This may cause a malfunction to the system.
• When using discs that have glue or similar tacky
substance on the label side of the disc or that used a
special ink when the label was printed, there is a
chance that the disc or label may become attached to
parts inside this unit. When this occurs, it may not be
possible to remove the disc, and may also cause this
unit to malfunction. Be sure to check that the label
side of the disc is not sticky before using.
– Very humid
– Subject to vibrations
– Subject to direct sunlight
• Use caution when placing the unit or speakers on
surfaces that have been specially treated (with wax,
oil, polish, etc.) as staining or discoloration of the
surface may result.
On heat buildup
• Although the system heats up during operation, this
is not a malfunction.
The following types of disc should not be used:
– Rental or used discs with attached seals where the
glue extends beyond the seal. The perimeter of the
seal on the disc is tacky.
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• If you continuously use this system at a high volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
– Discs that have labels printed using a special ink
that feels tacky when touched.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
• To prevent a malfunction, do not cover the
ventilation hole.
Cleaning the cabinet
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzine or alcohol.
32GB
To save a tape permanently
To prevent a tape from being accidentally recorded
over, break off the cassette tab from side A or B as
illustrated.
Specifications
Main unit (HCD-GPZ7/HCD-GPZ6)
Amplifier section
Break off the
cassette tab
HCD-GPZ7 for CMT-GPZ7
European model:
DIN power output (rated): 40 + 40 W (6 ohms at
1 kHz, DIN)
If you later want to reuse the tape for recording, cover
the broken tab with adhesive tape.
Continuous RMS power output (reference):
60 + 60 W (6 ohms at
1 kHz, 10% THD)
Before placing a cassette in the tape
deck
Take up any slack in the tape. Otherwise, the tape may
get entangled in the parts of the tape deck and become
damaged.
Music power output (reference):
100 + 100 W (6 ohms at
1 kHz, 10% THD)
Other models:
The following measured at AC 240 V, AC 220 V or AC
120 V
DIN power output (rated): 40 + 40 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
60 + 60 W
When using a tape longer than
90 minutes
The tape is very elastic. Do not change the tape
operations such as play, stop, and fast-winding
frequently. The tape may get entangled in the tape
deck.
(6 ohms at 1 kHz, 10%
THD)
Cleaning the tape heads
HCD-GPZ6 for CMT-GPZ6
Clean the tape heads after every 10 hours of use.
Be sure to clean the tape heads before you start an
important recording or after playing an old tape.
Use a separately sold dry-type or wet-type cleaning
cassette. For details, refer to the instructions of the
cleaning cassette.
European model:
DIN power output (rated): 40 + 40 W (6 ohms at
1 kHz, DIN)
Continuous RMS power output (reference):
50 + 50 W (6 ohms at
1 kHz, 10% THD)
Music power output (reference):
90 + 90 W (6 ohms at
1 kHz, 10% THD)
Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape after every 20 to 30 hours of
use with a separately sold demagnetizing cassette. For
details, refer to the instructions of the demagnetizing
cassette.
Other models:
The following measured at AC 240 V, AC 220 V or AC
120 V
DIN power output (rated): 30 + 30 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
40 + 40 W
(6 ohms at 1 kHz, 10%
THD)
Inputs
ANALOG IN (stereo mini jack):
Sensitivity 250 mV,
impedance 47 kilohms
Outputs
CD DIGITAL OUT:
Optical Wavelength:
660 nm
continued
33GB
PHONES (stereo mini jack):
SPEAKER:
Other models:
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
accepts headphones with
an impedance of 8 ohms or
more
accepts impedance of 6 to
16 ohms
Aerial
Aerial terminals
Intermediate frequency
AM loop aerial
External aerial terminal
450 kHz
CD player section
System
Compact disc and digital
audio system
Laser Diode Properties
Emission duration:
continuous
Laser Output*:
Speaker (SS-CGPZ7/SS-CGPZ6)
SS-CGPZ7 for CMT-GPZ7
Speaker system
Speaker units
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
2-way, bass-reflex type
Less than 44.6 µW
* This output is the value measurement at a distance of
200 mm from the objective lens surface on the
Optical Pick-up Block with 7 mm aperture.
13 cm dia., cone type
4 cm dia., cone type
6 ohms
Approx. 163 × 261 ×
260 mm
Frequency response
Wavelength
20 Hz – 20 kHz ( 0.5 dB)
780 – 790 nm
Mass
Approx. 2.9 kg net per
speaker
Tape deck section
Recording system
Frequency response
4-track 2-channel stereo
50 – 13,000 Hz ( 3 dB),
using Sony TYPE I
cassettes
0.15% W. Peak (IEC)
0.1% W. RMS (NAB)
0.2% W. Peak (DIN)
SS-CGPZ6 for CMT-GPZ6
Speaker system
Speaker units
Woofer:
Tweeter:
Nominal impedance
Dimensions (w/h/d)
2-way, bass-reflex type
Wow and flutter
12 cm dia., cone type
4 cm dia., cone type
6 ohms
Approx. 163 × 261 ×
230 mm
Tuner section
FM stereo, FM/AM superheterodyne tuner
Mass
Approx. 2.5 kg net per
speaker
FM tuner section
Tuning range
Aerial
Aerial terminals
Intermediate frequency
87.5 – 108.0 MHz
FM lead aerial
75 ohms unbalanced
10.7 MHz
General
Power requirements
European model:
Korean model:
Australian model:
Argentine model:
Mexican model:
Other models:
230 V AC, 50/60 Hz
220 V AC, 60 Hz
230 – 240 V AC, 50/60 Hz
220 V AC, 50/60 Hz
120 V AC, 60 Hz
AM tuner section
Tuning range
Pan-American model:
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval
set at 9 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
120 V, 220 V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage
selector
European model:
34GB
Power consumption
CMT-GPZ7
European model:
100 W
0.25 W (in Power Saving
Mode)
105 W
105 W
Mexican model:
Other models:
CMT-GPZ6
European model:
90 W
0.25 W (in Power Saving
Mode)
75 W
Other models:
Dimensions (w/h/d) (excl. speakers)
Approx. 181 × 261 ×
297 mm
Mass (excl. speakers)
Amplifier/Tuner/Tape/CD section:
CMT-GPZ7:
CMT-GPZ6:
6.1 kg
5.8 kg
Supplied accessories
Remote Commander (1)
R6 (Size AA) batteries (2)
AM loop aerial (1)
FM lead aerial (1)
CD-ROM (SonicStage) (1)
SonicStage Installation/
Operating Guide (1)
US and foreign patents licensed from Dolby
Laboratories.
Design and specifications are subject to change
without notice.
• Standby power consumption: 0.3 W
• Halogenated flame retardants are not
used in the certain printed wiring boards.
• Lead-free solder is used for soldering
certain parts.
• Halogenated flame retardants are not
used in cabinets.
35GB
List of button locations and reference pages
Illustration number
How to use this page
r
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
R
R
Name of button/part Reference page
Main unit
BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
Z PUSH OPEN/CLOSE (tape
m/M (tape rewind/fast
z PAUSE/START (record) qa
lm/ML (rewind/fast
forward, go back/go forward)
A – I
J – Z
Display window 4
PHONES jack e;
Remote sensor q;
VOLUME control 2
3
4
5 678 9
H
s
j
J
0
qa
qs
qd
qf
qg
qh
2
1
ef
ed
es
+
/
1
qj
qk
ql
w;
wa
ws
s
lj JL
HS
A
ea
e; wlwkwjwhwg wf wd
36GB
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A – E
m/M (rewind/fast forward)
./> (go back/go forward)
F – Z
CLOCK/TIMER SELECT 2
23)
1
2
3
4
5
6
7
w;
ql
qk
qj
qh
qg
qf
8
9
qd
qs
0
qa
37GB
Printed on 100 % recycled
paper using VOC (Volatile
Organic Compound)-free
vegetable oil based ink.
Sony Corporation Printed in China
|