Sony Stereo Receiver DRN XM01C User Manual

Fo r a ll Mo d e ls  
Fo r DRN-XM01C/XM01CK/XM01R  
Fo r DRN-XM01C/XM01CK/XM01R  
3-234-493-12(1)  
Caution  
6 Attach the supplied cover over the base of the stand as  
Mo u n t in g t h e An t e n n a w it h t h e  
Su p p lie d Se a l a n d Cu sh io n w it h t h e  
Do u b le -sid e d Ad h e sive Ta p e  
In st a llin g t h e An t e n n a o n t h e Ro o f (re co m m e n d e d )  
• Do not operate the unit in a way that might divert your attention from  
driving safely. As a driver, you alone are responsible for safely  
operating your vehicle in accordance with traffic safety laws at all times.  
• Do not install the unit where it may obstruct your view through the  
windshield or your view of your vehicles indicator displays.  
• Do not install the unit where it may hinder the function of safety  
devices such as an air-bag. Doing so may prevent the air-bag from  
functioning properly in the event of an accident.  
XM antenna*  
shown below.  
In st a llin g t h e Cra d le in yo u r  
In st a llin g t h e XM An t e n n a t o  
yo u r Ca r  
Ca r  
3
Cable guide***  
Digital Audio Receiver  
Accessory Kit  
Install the cradle with the supplied car stand.  
The bottom surface of the XM antenna is made of a magnet. Install the  
antenna horizontally in a location where the radio wave from the satellite  
is not interrupted by the body of the car (E.g., roof or trunk lid).  
Figure of the top  
1 Choose the mounting position, then shape the base of the  
2
• The installation and use suggestions contained in this manual are subject  
to any restrictions or limitations that may be imposed by applicable  
law— purchaser should check applicable law for any restrictions or  
limitations before installing and/ or operating this product.  
• Failure to follow these safety instructions and warnings may result in a  
serious accident.  
stand to match the mounting surface.  
Water proof cushion  
Cord clamp**  
Note  
Installation Guide  
1
Bend the base gently so there are no gaps between the base and the  
mounting surface.  
Inside of the trunk  
Rubber packing  
Cable guide***  
OWNER’S RECORD  
Attach to the antenna.  
2
The model number is located on the bottom and serial number  
also on the bottom. Record the serial number in the space  
provide below. Refer to these numbers whenever you call upon  
your Sony dealer regarding this product.  
7 Attach the cradle to the stand.  
Cushion with the  
double-sided  
Pa rt s fo r In st a lla t io n a n d  
Co n n e ct io n  
adhesive tape  
3
Put the water proof cushion parallel on the rubber packing using the  
double-sided adhesive tape.  
Model No.  
Serial No.  
Notes on installing the antenna to your car  
• Mount the antenna gently so that it does not damage the body of the  
car.  
Seal  
for DRN-XM01C/XM01CK/XM01R  
• Do not leave the cord slackened outside of the car.  
• Use the cord clamp when fixing the cord, if required.  
• When removing the antenna, do not pull it by the cord. This may cause  
the cord to come off the antenna because of the powerful magnet.  
• The antenna cord is charged with the XM signal and the power supply  
to the antenna. When wiring the antenna, be careful not to pinch the  
cord in the moving parts of the car. The damaged cable may cause a  
malfunction of the antenna and the main unit.  
Figure of the side  
XM antenna (1)  
Remote commander (1)  
Car cradle (1)  
2 Clean the mounting surface well.  
Water proof cushion  
1
Figure of the back  
DRN-XM01C/DRN-XM01R/  
DRN-XM01H/DRN-XM01CK/  
DRN-XM01HK  
3 Peel off the protective film from the base of the stand and  
To the stand  
receptacle at the  
bottom of the  
cradle  
Attach to the trunk lid.  
attach the base to the mounting surface.  
Water proof cushion  
Make sure the base attaches to the mounting surface completely.  
Double-sided  
adhesive tape  
Note  
When removing the seal, preheat the mounting surface with a hairdryer  
then pull up slowly to remove, or use a commercially available solvent to  
remove the seal.  
Rubber  
packing  
• When washing the car in an automatic car wash, remove the antenna.  
Otherwise, it may damage the body of the car.  
Cord clamp**  
8 Adjust the angle.  
Water proof  
cushion (1)  
Screw (5)  
Cover (1)  
Car stand (1)  
Double-sided  
adhesive tape  
Cord clamp**  
Rubber  
packing  
Installing the antenna to an aluminum or plastic  
body  
The antenna cannot be installed on an aluminum or plastic body with the  
magnet. In this case, use the supplied seal.  
In st a llin g t h e An t e n n a o n t h e Tru n k  
Lid  
Printed on 100%  
recycled paper using  
VOC (Volatile Organic  
Compound)-free  
Sony Corporation ©2001 Printed in Japan  
Put the water proof cushion on the rubber packing with the flat  
surface downward using the double-sided adhesive tape.  
Cord clamp**  
vegetable oil based ink.  
1
Mount the antenna on the trunk lid.  
Clean the mounting surface before mounting.  
Seal (1)  
Cushion with the  
double-sided  
Cable guide (3)  
Cord clamp (4)  
*
Be sure to install the antenna firmly on a flat surface. Do not install on the corner of the roof.  
Painting the antenna  
The antenna can be painted according to the body color of the car,  
however, do not use paint that contains metal powder. This may cause  
deterioration or inability of reception.  
adhesive tape (1)  
** • Be sure to install the cord clamp in a lower position where the water proof cushion is mounted. Otherwise, it will cause a water leak into the trunk.  
• Clean the mounting surface before installing the cord clamp.  
• Leave the installed cord clamp for 24 hours before installing the cord. Otherwise, the cord clamp may come off because of weak attachment.  
*** • Cut the cable guide, if required.  
For customers in the USA  
productregistration.  
Proper registration will enable us to send you periodic mailings about  
new products, services, and other important announcements.  
Registering your product will also allow us to contact you in the  
unlikely event that the product needs adjustment or modification.  
Thank you.  
Notes  
Cable guide  
• The double-sided tape will not stick firmly if the mounting surface  
temperature is lower than 20°C (68°F). Use a hairdryer, etc. to warm  
up the mounting surface before mounting.  
• Consider the mounting position carefully beforehand. If you change  
the position after mounting the double-sided tape will weaken.  
• When removing the stand, preheat the mounting surface with a  
hairdryer then slowly pull up to remove, or use a commercially  
available solvent to remove the seal.  
Do not disassemble the antenna when painting.  
• It is difficult to attach the cable guide to a body or window which has fluorine resin coating.  
You can also adjust the angle after installing the main unit into the  
cradle.  
fo r DRN-XM01C/XM01CK o n ly  
Car battery cord (1)  
Car connecting pack (1)  
Placement of the car antenna  
Notes  
Place the antenna on a flat and even surface on your car roof. The angle  
from the ground to the satellite should be about 20 - 60 degrees. If you  
place the antenna on the trunk lid, make sure your car roof does not block  
the satellite signal. Depending on where you live, you may be able to  
receive radio waves that are retransmitted by ground repeaters.  
20° or less  
Leading the antenna cord into the car through  
the space betw een door and body  
When installing the antenna on the roof, you can also lead the antenna  
cord into the car through the space between door and body.  
• Do not install the unit in a location where it may be subjected to  
extremely high or low temperatures as the cabinet may become  
deformed or damaged. After parking your car, the temperature inside  
the car may raise considerably. Therefore, cover the cradle and the main  
unit with a white cloth or remove it from the cradle to avoid the direct  
sunlight.  
• Do not install the cradle, the main unit and RF modulator in the  
following places:  
– Underneath the drivers seat: There may be a danger of the unit  
getting lodged under the brake pedal.  
Fo r DRN-XM01H/XM01HK Cu st o m e rs  
WARNING  
4 Fix the stand with the supplied screws.  
Note  
fo r DRN-XM01R o n ly  
Before drilling holes in the mounting surface, make sure there is  
nothing behind the mounting surface.  
RF modulator (1)  
To p re ve n t fire o r sh o ck h a za rd , d o n o t e xp o se t h e u n it  
t o ra in o r m o ist u re .  
2
Mount the water proof cushion on the back side of the trunk  
lid.  
You are cautioned that any changes or modifications not expressly  
approved in this manual could void your authority to operate this  
equipment.  
– On the door or ceiling: There may be a danger of the unit falling down  
or obscuring the drivers view while driving.  
To prevent rain water leakage inside the car along the cord, mount the  
water proof cushion above the rubber packing when the trunk lid is  
closed.  
INFORMATION  
Cord clamp*  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interfer-  
ence in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accor-  
dance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will  
not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
– Reorient or relocate the receiving antenna.  
Cable guide*  
Water proof  
cushion  
for DRN-XM01H/XM01HK  
Remote  
commander (1)  
Home cradle (1)  
XM antenna (1)  
Antenna cord  
5 Remove the knob.  
Trunk lid  
Rubber packing  
Cord clamp*  
Water proof  
cushion  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
*
• Clean the mounting surface before installing the cord clamp.  
• Leave the installed cord clamp for 24 hours before installing the  
cord. Otherwise, the cord clamp may come off because of weak  
attachment.  
Audio cord (1)  
AC power adaptor (1)  
Home stand (1)  
– Consult the dealer or an experienced radio/ TV technician for help.  
This device complies with Part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) This device must accept any interference received,  
including interference that may cause undesired operation.  
* • Cut the cable guide, if required.  
• It is difficult to attach the cable guide to a body or window which  
has fluorine resin coating.  
 

Sony DVD Recorder PDW F70 User Manual
Sony MiniDisc Player MZ DH10P User Manual
Sony Portable CD Player 2 896 703 72 2 User Manual
Sony Printer LPR 1000MD User Manual
Sony Projector VPH D50QM User Manual
Sony Security Camera Smarter Security User Manual
Sony Stereo System CDP CX400 User Manual
Sony Wireless Office Headset MDR 10RBT User Manual
SOYO Computer Hardware SY 6VBA 133 User Manual
Stiga Lawn Mower 12 5286 19 User Manual