WWW.SHARKCLEAN.COM
S3501 N
S3501BB
OWNER’S GUIDE
S3501_N_S3501BB_11_IB_ENG_101119.indd
1
10-11-22 2:28 PM
English
11. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
22. Never use Steam Pocket® Mop
without micro-fiber pocket
attached.
23. Keep your work area well lit.
24. Store Steam Pocket® Mop indoors
in a cool, dry place.
12. DO NOT put any objects into
openings. Do not use with any
opening blocked.
25. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
13. DO NOT put hands or feet under
the Steam Pocket® Mop. Unit gets
very hot.
26. If an extension cord is absolutely
necessary, an extension cord rated
a minimum of 15 ampere, 14 gage
cord should be used. Cords rated
for less amperage may overheat.
Care should be taken to arrange
cord so that it cannot be pulled or
tripped over.
14. Use ONLY on flat, horizontal
surfaces. Do not use on walls,
counters or windows.
15. DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or other
delicate, steam sensitive materials.
27. DO NOT leave your Steam Pocket®
Mop unattended when the system
is connected to a power supply
/electrical outlet.
16. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your Steam Pocket® Mop.
28. DO NOT store unit with damp/wet
micro-fiber Steam Pocket® pocket
attached. Never leave the Steam
Pocket® Mop in one spot on any
surface for any period of time with
a damp or wet micro-fiber Steam
Pocket® pocket attached as this
will damage your floors.
17. When in use, NEVER turn the
appliance over or on its side.
NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
29 Always unplug and allow the
Steam Pocket® Mop to cool before
removing or changing mop heads.
18. NEVER LEAVE THE Steam
Pocket® Mop IN ONE SPOT ON
ANY SURFACE FOR ANY PERIOD
OF TIME WHEN MICRO-FIBER
POCKET IS ATTACHED.
WARNING: Your Steam Pocket®
Mop is designed to clean hard
floor surfaces that will withstand
high heat. Do not use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by the
heat and steam action. It is always
recommended to test an isolated
area of the surface to be cleaned
before proceeding. We also
19. Carefully remove the micro-fiber
pocket immediately after you have
unplugged and allowed the Steam
Pocket® Mop to cool.
20.When cleaning the Steam Pocket®
Mop, unplug the power cord from
the electrical outlet and clean with
a dry or damp cloth. Do not pour
water or use alcohol, benzene or
paint thinner on the unit.
recommend that you check the use
and care instructions from the floor
manufacturer.
21. Extreme caution should be
exercised when using this
appliance to clean stairs.
S3501_N_S3501BB_11_IB_ENG_101119.indd
3
10-11-22 2:28 PM
Quick Start
When assembling your Steam Pocket®
Mop there may be a little water in or
around the water tank. This is because
we test all our Steam Pocket® Mops
100% before you buy them, so you get
a quality Shark® Steam Pocket® Mop.
2
1
4
3
ASSEMBLE
1
Insert the mop handle into the
pump actuator (the tube that leads
to the tank). Push the mop handle
and pump actuator together in
until you hear it click into place.
FILL
4
Lay the mop on the floor or on
a counter top and remove the
water tank cap by turning counter
clockwise. Fill the water tank using
the filling flask. Do not overfill the
water tank. Replace the water cap
and tighten.
2
Select a cleaning pad. Fit one side
of the pocket onto the head first,
then using the lavender loop, pull
the pocket over the head. Attach
the quick fasteners on the top of
the pocket to secure in place.
IMPORTANT: Make sure your floors
are sealed. Before using the Steam
Pocket® Mop consult page 4 for
more information.
3
Snap the mop head into the base to
secure it. Press the release button
to exchange mop heads.
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd
4
10-11-22 2:28 PM
DIRT CAN’T HIDE ON
EITHER SIDE! All new
design allows for optimal
cleaning! When one side
of the pocket gets dirty,
just turn the mop head
over and clean with the
other side of the pocket.
5
QUICK TIP:
For easier
pushing
and pulling,
extend the
handle length.
6
PREPARE
NOTE: Do not leave your
Steam Pocket® Mop
unattended during use.
5
For your comfort, you can adjust
the height of the mop. Just lift the
latch on the tube 90 degrees to the
open position. Holding the handle,
extend the tube to the height that’s
right for you and then close latch
to locked position.
IMPORTANT: Never leave
the Steam Pocket® Mop in
one spot for any period of
time with a damp or wet
micro-fiber Steam Pocket®
attached as this will damage
your floors.
6
Plug in mop and wait 30 seconds
or less for the mop to heat up.
Pump the handle of the mop by
pushing downward about 10 to 12
times to create steam.
NOTE: Steam is created
automatically when you start
mopping.
S3501_N_S3501BB_11_IB_ENG_101119.indd
5
10-11-22 2:28 PM
This manual covers model number:
S3501 N 11
S3501BB 11
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1550 Watts
Water
Capacity: 450 ml (15 oz.)
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd
6
10-11-22 2:28 PM
English
Contents
Getting Started......................................................................2
Using Your Steam Pocket® Mop......................................6
Using Your Carpet Glider...................................................8
Care of Your Steam Pocket® Mop...................................9
Ordering Replacement Parts ...........................................11
Troubleshooting Guide .......................................................12
Warranty and Registration................................................13
Thank you for
purchasing the
Shark® Steam
Pocket® Mop.
1
S3501_N_S3501BB_11_IB_ENG_101119.indd
1
10-11-22 2:28 PM
Getting Started
f
d
When assembling your Steam Pocket®
Mop there may be a little water in or
around the water tank. This is because
we test all our Steam Pocket® Mops
100% before you buy them, so you get a
quality Shark® Steam Pocket® Mop.
e
g
a
i
j
h
c
k
b
a 2 All Purpose Cleaning Pads
b Carpet Glider
d Quick Release Swivel Cord Wrap
e Cord Clips
c Filling Flask
f
Mop Handle
g Telescopic Handle Latch
h Water Tank Viewing Window
i
Power-On Blue Light
(Lights up when plugged-in)
j
Water Tank Cap
k Rectangle Mop Head
2
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd
2
10-11-22 2:28 PM
English
2
1
IMPORTANT: First things first, always
make sure the mop is UNPLUGGED
from the wall when not in use. Never
fill the mop, attach the mop head,
change or remove the micro-fiber
pocket when the mop is plugged into
the wall. If you have hard water you
might want to use distilled water to
prolong the life of the Shark® Steam
Pocket® Mop. Make sure you only
add water to the tank. Chemicals or
cleaning solution may damage the
appliance and could be unsafe for
you and your family.
ASSEMBLE
1
Insert the mop handle into the pump
actuator (the tube that leads to the
tank). Push the mop handle and
pump actuator together in until you
hear it click into place.
2
Select a cleaning pad. Fit one side
of the pocket onto the head first,
then using the lavender loop, pull
the pocket over the head. Attach
the quick fasteners on the top of the
pocket to secure in place.
3
S3501_N_S3501BB_11_IB_ENG_101119.indd
3
10-11-22 2:28 PM
Getting Started
Calcium and mineral deposits
can build up and impact the
performance of your steam mop
over time. To extend the life of
your product we recommend that
you use distilled water or Shark®’s
Water Filtration Bottle. Visit www.
sharkclean.com to order.
3
4
3
Snap the mop head into the base to
secure it. Press the release button to
exchange mop heads.
IMPORTANT: Don’t use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by
the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
recommend that you check the use
and care instructions from the floor
manufacturer.
4
Turn the water tank cap counter
clockwise and remove from the tank.
Use the filling flask and pour water
into the tank. Please don’t overfill.
Replace the cap on the water tank by
turning clockwise and tightening.
4
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd
4
10-11-22 2:28 PM
English
5
5
For your comfort, you can adjust the
height of the mop. Just lift the latch
on the tube 90 degrees to the open
position. Holding the handle, extend
the tube to the height that’s right for
you and then close latch to locked
position.
QUICK TIP: For easier pushing and
pulling, extend the handle length.
5
S3501_N_S3501BB_11_IB_ENG_101119.indd
5
10-11-22 2:28 PM
Using Your Steam Pocket® Mop
IMPORTANT: Make sure you don’t
use the mop without attaching
a micro-fiber pocket and adding
water to the tank first. When you are
using the mop for the first time, it
might take longer than the normal
30 seconds to start steaming. Just
pump the handle a few times in a
downward motion to prime the
pump and it should be ready.
2
1
NOTE: Make sure the floors are
swept or vacuumed before using the
Steam Pocket® Mop.
2 Pump the handle a few times in a
downward motion. This pumping
action will release steam as you
mop and allows you to customize
the amount of steam you want.
Begin mopping with a forward
and backward motion. The natural
motion of mopping will produce
steam.
1
Pull and twist the quick release cord
holder to unwrap the power cord
completely. A great time saver!
Plug into a 120-volt electrical outlet
The power “On” light will turn blue, it
takes approximately 30 seconds for
the mop to heat up and the steam to
be ready.
6
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd
6
10-11-22 2:28 PM
English
3
3 When one side of the micro-fiber
pocket gets dirty, just flip the mop
head and you can quickly start using
the other side. Dirt can’t hide on
either side.
4 When the water tank is empty,
the Steam Pocket® Mop will stop
producing steam. You can refill the
water tank at any time as long as the
mop is unplugged from the outlet.
Follow the instructions from
page 4. This goes for switching the
mop heads or micro-fiber Steam
Pocket® as well.
IMPORTANT: Please wait 3-5 minutes
for the Steam Pocket® Mop to cool
off before switching the mop head or
the micro-fiber Steam Pocket® .
IMPORTANT: Never leave the
Steam Pocket® Mop with a damp/
wet micro-fiber pocket on any floor
surface for any amount of time as
this may damage the floor.
7
S3501_N_S3501BB_11_IB_ENG_101119.indd
7
10-11-22 2:28 PM
Using Your Carpet Glider
The Steam Pocket® Mop won’t
clean your carpeting or area
rugs. However, it’s great for
deodorizing and freshening.
1
THE CARPET GLIDER
1 The Carpet Glider can be used to
lightly steam your carpet and area
rugs. Just place the mop head on
top of the glider and move back and
forth across a section of the carpet.
The Steam Pocket® Mop won’t clean
your carpeting or areas rugs, but it’s
great for deodorizing and freshening.
NOTE: Please note that the Steam
Pocket® Mop rests on top of the
carpet glider and it is not a fixed
attachment.
Do not leave Steam Pocket® Mop
with carpet glider in one stationary
position for any period of time.
8
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd
8
10-11-22 2:28 PM
English
Care of Your Steam Pocket® Mop
AFTER USE AND STORAGE
1
When you have finished using the
Steam Pocket® Mop, and your
floors are clean, unplug the cord
from the outlet and move it into an
upright position. Let the unit cool
2-3 minutes and release steam by
pumping the handle several times
before removing the micro-fiber
Steam Pocket® from the mop head.
3
1
2
2 Remove the micro-fiber Steam
Pocket® by releasing the quick
fasteners and using the lavender
loop on the side of the pocket,
avoiding contact with the hot pocket
or dirt. Then empty the water tank.
3 To store the Shark® Steam Pocket®
Mop hanging up; first remove the
head (after it has cooled and the
steam has been released) then hang
on a large hook.
NOTE: If you want to store it
standing upright, then make sure
it’s leaning against a wall for added
support and safety. Always store
your Steam Pocket® Mop with
the micro-fiber Steam Pockets®
removed, away from children or high
traffic areas.
IMPORTANT: Be very careful
because the Steam Pockets® can
get very hot from the steam, so use
caution when removing them. Let the
unit cool 2-3 minutes.
9
S3501_N_S3501BB_11_IB_ENG_101119.indd
9
10-11-22 2:28 PM
Care of Your Steam Pocket®Mop
2
1
KEEPING YOUR MICRO-FIBER
STEAM POCKET® POCKET AS GOOD
AS NEW
We recommend washing your
micro-fiber Steam Pockets®
separately from other fabrics to
avoid picking up lint.
2 If there are loose threads on the
pocket carefully cut the thread with
scissors. Don’t pull on them or cut at
the base.
1
Only use liquid detergent.
(No powder detergent) Don’t use
any fabric softeners or bleach.
Line dry or dry on a low dryer
setting.
10
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd 10
10-11-22 2:28 PM
English
Ordering Replacement Parts
1
2
3
4
5
ORDERING REPLACEMENT PARTS
PART
PART NO.
To order additional parts and
accessories, feel free to contact us at
1 (2) All-Purpose
Cleaning Pads
XT3501
or call 1-800-798-7398.
2 (2) Steam Duster
Cleaning Pads
XT3501SD
1024SO
3 Rectangle Mop Head
4 Triangle Mop Head
5 Carpet Glider
1025SO
XCG3501CON
11
S3501_N_S3501BB_11_IB_ENG_101119.indd 11
10-11-22 2:28 PM
Troubleshooting Guide
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Your Steam Pocket® Mop should be securely plugged into a
120V AC electrical outlet only.
The Steam Pocket®
Mop will not
turn on.
Check your fuse or breaker.
If your unit still doesn’t work, give us a call 1-800-798-7398.
Prime the pump, see page 6 for more information.
Steam Pocket® Mop
will not make steam.
Is there water in the water tank? If not, add water to your
Steam Pocket® Mop following the instructions.
Check to see if your micro-fiber Steam Pocket® is too wet.
We recommend you unplug the Steam Pocket® Mop and
change the micro-fiber Steam Pocket®.
Steam Pocket® Mop
leaves water on the
floor.
Make sure the steam pocket is attached correctly.
Make sure the steam pocket is attached correctly.
Check to see if your pocket is excessively dirty.
Try increasing the height of the pole for better leverage.
Steam Pocket® Mop is
hard to push.
The micro-fiber pocket might be dirty. Flip or change
the pocket.
If you washed the pocket with powder detergent then the
pocket might be ruined.
If you are cleaning in a kitchen area where there might be a
build-up of grease then use a degreasing agent such as an
all-purpose cleaner or dish soap and paper towels to clean
the area first.
Floors are cloudy,
streaky or spotty
after steaming.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do you, we recommend
switching to distilled water.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if the
leftover cloudiness is removed.
12
TOLL FREE: 1-800-798-7398
S3501_N_S3501BB_11_IB_ENG_101119.indd 12
10-11-22 2:28 PM
English
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and a check made out to EURO-
PRO Operating LLC in the amount of $ 9.95 to cover the cost of return shipping and handling
must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to
the specific obligations expressly assumed by it under the terms of the limited warranty. In no
event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with item. We recommend you insure the package (as damage in shipping is
not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………………...........................................
ADDRESS: …………………………………………...............................……………………………………………………...............
S3501BB / S3501 N
DATE OF PURCHASE: …………………...............................….. MODEL: ………………...................................
NAME AND ADDRESS OF STORE: ……………………………………………………………...............................……..
13
S3501_N_S3501BB_11_IB_ENG_101119.indd 13
10-11-22 2:28 PM
U.S.:
EURO-PRO Operating LLC
Newton, MA 02459
Canada: EURO-PRO Operating LLC
4400 Bois Franc
Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
COPYRIGHT© EURO-PRO OPERATING LLC 2010
PRINTED IN CHINA
US Patent D597717, 7669280,
7600401, D626302, D599517
Illustrations may differ from actual product.
S3501_N.S3501BB.E.101119
S3501_N_S3501BB_11_IB_ENG_101119.indd 14
10-11-22 2:28 PM
|