Sears Power Supply 20071486 User Guide

OPERATOR’S MANUAL  
®
Portable Power 750  
Jump Starter and  
DC Power Source  
Model No.  
200.71486  
CAUTION:  
Read all Safety Rules and Operating Instructions,  
and follow them with each use of this product.  
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.  
00-99-000863/0808  
 
IMPORTANT: CHARgE IMMEDIATELY AfTER PURCHASE  
IMPORTANT: READ AND SAvE THIS SAfETY AND INSTRUCTION MANUAL.  
1.  
IMPORTANT SAfETY INSTRUCTIONS  
1.1  
Charge the 750 internal battery immediately upon purchase, every 30  
days and after every use.  
1.2  
1.3  
Use in a well ventilated space.  
Contains a sealed, non-spillable lead-acid battery. Must be disposed of  
properly.  
1.4  
1.5  
wARNINg: Possible explosion hazard. Contact with battery acid may  
cause severe burns and blindness. Keep out of reach of children.  
wARNINg: Pursuant to California Proposition 65, this product contains  
chemicals known to the State of California to cause cancer and birth de-  
fects or other reproductive harm.  
1.6  
2.  
wARNINg: Failure to follow instructions may cause damage or an explo-  
sion. Read entire instruction manual before use. Always wear safety glass-  
es to protect your eyes during use.  
DIEHARD PORTAbLE POwER 750 JUMP-STARTER/DC POwER  
SOURCE PRODUCT fEATURES  
5
1. Jump-start ON/OFF switch.  
This switch supplies power to  
the clamps for jump-starting.  
4
2. Light/Display switch. This  
switch turns on the light or the  
internal battery status display.  
1
3. Internal Battery Status Display  
(LEDs)  
4. Plastic lens cover  
5. Light bulb  
6
8
7
6. 12V DC power outlet (Not  
shown)  
2
7.  
Side charger plug (not shown)  
3
8. Clamps  
1 •  
 
3.  
CHARgINg THE INTERNAL bATTERY  
IMPORTANT:  
CHARgE IMMEDIATELY AfTER PURCHASE  
KEEP fULLY CHARgED.  
This Portable Power 750 comes with a sealed, non-spillable DieHard  
maintenance-free lead-acid battery. This internal battery is specifically  
designed to deliver high power jump-starting as well as repetitive deep  
cycling performance.  
To charge the Portable Power 750 internal battery:  
3.1  
3.2  
Check the internal battery’s charge level by pressing the switch marked  
DISPLAY. The internal battery status LEDs will light.  
NOTE: Internal battery status LEDs are most accurate when the Portable  
Power 750 has been disconnected from all devices and charging sources  
for 1 - 24 hours.  
Using a proper extension cord, connect the cord to the charge plug and  
then plug the cord into a properly wired and live 110Vac/60Hz wall outlet.  
CAUTION: Operating the Portable Power 750 while the internal battery is  
being charged may cause permanent damage to the unit.  
3.3  
3.4  
While the Portable Power 750 is charging, the red “CHARgINg” LED will  
illuminate. When the internal battery is fully charged, the green “FULL”  
LED will illuminate. Complete charging may take up to 72 hours. The Por-  
table Power 750 is then ready to use.  
Once the battery is fully charged, the built-in charger automatically switch-  
es to float-mode monitoring, which trickle charges the battery and keeps it  
fully charged without overcharging.  
The internal battery may also be charged while you drive using the male-  
to-male accessory cable (available separately, see “Accessories and Re-  
placement Parts” section of this manual). Insert one end of the accessory  
cable into the 12V DC power outlet and the other end into the vehicle’s  
accessory outlet (lighter socket). Completely disconnect the accessory  
cable when the engine is not running.  
4.  
JUMP-STARTINg A vEHICLE ENgINE  
Use in a well-ventilated area. Keep hands, hair, clothing and jewelry clear  
of fan blades, belts, pulleys and other parts that may cause injury.  
4.1  
4.2  
4.3  
Turn ignition off before making cable connections.  
Make sure the jump-start ON/OFF switch is in the OFF position.  
Place the 750 on a flat, stable surface near the vehicle battery and away  
from moving engine parts.  
2 •  
 
4.4  
4.5  
Connect the red clamp to the positive (+) terminal of the vehicle battery.  
Connect the black clamp to an unpainted and unmoving part of the vehicle  
chassis or engine block. Do not connect to the carburetor, fuel lines or  
sheet-metal body parts.  
CAUTION: If you have connected the clamps backwards, an audio alarm  
will sound. DO NOT turn the ON/OFF switch to the ON position. This could  
cause serious damage. Reverse the connections and the audio alarm will  
stop.  
4.6  
4.7  
Turn the JUMP START ON/OFF switch to the ON position.  
Turn the key and crank the engine. If the engine does not start within 5-8  
seconds, stop cranking and wait at least 1 minute before attempting to  
start vehicle again. This permits the battery to cool down.  
4.8  
4.9  
After the engine starts, turn the JUMP START ON/OFF switch to OFF.  
Disconnect the black clamp first and then the red clamp. Store the clamps  
on the ears located on the back of the case.  
4.10 Charge the 750 as soon as possible after jump-starting.  
CAUTION: To prevent sparking while the 750 jump-start switch is in the  
ON position, NEVER allow the clamps to touch together or to contact the  
same piece of metal. And, never attempt to charge a frozen battery.  
NOTE: In the rare case of jump-starting a vehicle that has a positive-  
grounded vehicle electrical system, connect the black clamp to the  
negative terminal of the vehicle battery. Then connect the red clamp to  
an unpainted and unmoving part of the vehicle chassis or engine block. If  
you are unsure of the nature of the vehicle’s electrical grounding system,  
check the owner’s manual of the vehicle or call the Customer Technical  
Assistance number: 1-800-SEARS-64.  
5.  
POwERINg A 12v DC DEvICE  
The Portable Power 750 is a power source for all 12 volt DC accessories  
that are equipped with a 12V accessory plug. The DC accessory outlet  
has a 15-amp automatic overload protection circuit breaker. The breaker  
will automatically reset after an overload occurs.  
To operate a 12V DC device:  
5.1  
5.2  
5.3  
Open the protective cover of the DC power outlet on the right side of the  
Portable Power 750.  
Plug the 12V DC device into the DC power outlet, and turn on the 12V DC  
device (if required).  
If the 12V DC device draws more than 15A, the internal circuit breaker of  
the Portable Power 750 will momentarily disconnect power to the device.  
If this occurs, unplug the device and the circuit breaker will automatically  
reset after several seconds.  
3 •  
 
5.4  
6.  
Charge the Portable Power 750 as soon as possible after each use.  
Because the DC power outlet is internally wired directly to the internal  
battery, extended operation of a 12V DC device may result in excessive  
battery drain.  
12v DC ELECTRICAL DEvICE ExAMPLE RUN-TIME CHART  
Appliance Type  
Estimated Power  
Estimated  
Time*  
Fluorescent Lights, Cellular Phones  
Radios, Depth Finders, Fans  
Camcorders, DVD Players, Spotlights  
Electrical Tools, Bilge Pumps  
Electric Coolers  
4 Watts  
20 Hours  
14 Hours  
8 Hours  
5 Hours  
2 Hours  
1 Hour  
9 Watts  
15 Watts  
24 Watts  
48 Watts  
80 Watts  
Air Compressors, Car Vacuums  
*NOTE: Estimated run-times. Actual time may vary. Times are based on  
the internal battery being new, fully charged and operated at room tem-  
perature.  
7.  
USINg THE bUILT-IN LIgHT  
7.1  
7.2  
Position the 750 on a flat, stable surface near the intended work area.  
Turn the Light/Display switch to the LIgHT position. The light will turn on  
and illuminate your work area.  
NOTE: With a fully charged internal battery, the built-in light should  
provide 18 to 30 hours of continuous useful light, depending on ambient  
conditions.  
7.3  
7.4  
Turn the Light/Display switch to the OFF position when work is completed.  
Charge the 750 as soon as possible after using the built-in light.  
4 •  
 
8.  
LED INDICATORS  
To check the internal battery status, press the switch on the front of the  
750 to the DISPLAY position.  
The LED lights will indicate as follows:  
8.1  
8.2  
8.3  
9.  
A red light indicates a 50% or less charge and you should immediately  
charge the 750.  
A yellow light indicates a 50 to 75% charge. The 750 may be used, but  
should be charged as soon as possible.  
A green light indicates a 75% to 100% charge.  
STORAgE AND MAINTENANCE  
IMPORTANT:  
CHARgE IMMEDIATELY AfTER PURCHASE  
KEEP fULLY CHARgED.  
Charge the 750 internal battery immediately upon purchase, every 30  
days and after every use.  
All batteries are affected by temperature. The ideal storage temperature is  
between 40 and 70 degrees Fahrenheit. The internal battery will gradually  
self-discharge (lose power) over time more quickly in warm environments.  
Leaving the battery in a discharged state may result in permanent battery  
damage. To ensure satisfactory performance and avoid permanent dam-  
age, charge the internal battery every month.  
When the JUMP START ON/OFF switch is ON, the clamps are live and  
will produce arcing or sparking if they come in contact with each other. To  
prevent accidental arcing, always keep the clamps on the storage holders  
and the JUMP START ON/OFF switch in the OFF position when not using  
it to jump start a vehicle.  
9.1  
Replacing the built-in light  
To replace the built-in light bulb:  
1. Turn the light off.  
2. Insert a standard (flat-blade) screwdriver into one of the two slots along  
the bottom of the plastic lens and gENTLY pop the lens out. Repeat for  
the other side.  
3. gently grasp the bulb and twist counter-clockwise one quarter-turn to  
unscrew the bulb.  
4. Insert a replacement bulb of the same type and rating, and twist clock-  
wise one quarter-turn to screw in the new bulb.  
5. Replace the lens cover.  
6. Test the light by switching the light on and off.  
5 •  
 
9.2  
Customer Technical Assistance  
Customer technical assistance is available Monday-Friday, 7 am to 4:30  
pm Central Time by phoning 1-800-SEARS-64.  
10. SPECIfICATIONS  
Internal Battery Type  
Nominal Voltage  
DieHard Maintenance-free AgM Lead-acid  
12v DC  
Capacity  
12 Ah  
DC Power Outlet (Max. Continuous Load)  
Built-in Light Bulb (Replaceable)  
Jumper Cables  
15A With Automatic Circuit Breaker Reset  
5w/12v DC (Base type BA9S)  
8-gauge AWg, 18 Inches  
9.5 H x 10 x 8 Inches  
12.2 Lbs.  
Dimensions (H x W x D)  
Product Weight  
11. ACCESSORIES AND REPLACEMENT PARTS  
Parts and customer technical assistance is available Monday-Friday, 7 am  
to 4:30 pm Central Time at 1-800-SEARS-64.  
Male-to-Male Accessory Cable: 38-99-000834 (Use for charging Por-  
table Power 750 from a vehicle’s 12V accessory outlet.)  
Replacement Light bulb: 00-00-000722  
Lens Cover: 37-99-00399-0  
6 •  
 

Radica Games Video Game Controller 8074 User Guide
RCA Flat Panel Television L46WD250 User Guide
Ricoh MP3 Player CL3000 User Guide
Rinnai Boiler 800000026 User Guide
Roku Portable Multimedia Player 2450D User Guide
Ryobi Trimmer 890r User Guide
Samsung Bluetooth Headset GH68 19212A User Guide
Samsung Washer S1003J User Guide
Samsung Washer Silver Care Washer User Guide
Senco Power Screwdriver DS200 S4 User Guide