Prizelawn CD36C
®
COMMERCIAL DROP SPREADER
MODEL CD36C
OWNER’S MANUAL
Operation
1. Before filling Hopper, make sure spreader
Handle Lever is in the “OFF” position. Always fill
spreader on walk or drive, not on the lawn.
4. Operate spreader at 3 MPH pace.
(33.3 feet in 7.5 seconds)
5. Apply two header strips at each end
of area to treated and then proceed
lengthwise between the header strips.
Be sure to overlap the wheel tracks
slightly to prevent streaking.
2. Loosen Rate Control Knobs and move the Tie
Bar to setting recommended for the product
applied. If PrizeLAWN settings are not available,
use Scotts® drop spreader settings. If setting is not
known, refer to “DETERMINING APPLICATION
RATES” section of this book. Retighten knobs after
setting is made.
6. When applying lime, do not use lime-
stone that is so finely ground that it will
pack inside the Hopper, or use hard,
abrasive particles which will damage
the spreader.
3. Always push spreader, do not pull.
Start spreader in motion and as it passes
over the area to be treated, push Handle
Lever to the “ON” position. Close Handle
Handle Lever at the end of each pass.
Use only compacted, free flowing, non-
abrasive lime products.
Determining Application
Rates For Drop Spreaders
Maintenance
The following procedure provides a means of accurately
determining drop spreader settings when settings do not
appear on the package, or to “fine tune” the manufacturer’s
recommend settings. Spreader rates can vary due to
walking speed, condition of turf. humidity, physical characteristics
of the product being applied, or condition of the spreader. It is
good practice to double check settings using the following
method:
1. Never store unused material in spreader. Return
unused product to its original container.
2. Set Rate Slide on the highest number, open
spreader and spin Wheels to remove excess material.
3. Wash out Hopper thoroughly after each use to
remove material clinging to surfaces. Pay close
attention to area between the Shutoff Bar and Hopper.
Allow spreader to completely dry.
PROCEDURE
EXAMPLE
1. The manufacturer will recommend
coverages on the product package.
Generally, it is stated as applying
a certain number of pounds of
The contents of this
package (25 lbs.)
covers 2,000 square
feet.
4. Oil bottom of Hopper, Control Housing Spring and
Agitators at the Center Bearing. Lubricate Axle
Bearings with grease. Store spreader in open position.
product per 1,000 square feet.
2. Determine the amount of material
in pounds to cover 100 square
feet. Add two zeros to weight
of bag and divide that by the
square foot coverage.
2,500 divided by 2,000
square feet= 1.25 lbs.
“Open”
Oil
Oil
3. To change the decimal portion
of answer in step #2 to ounces,
multiply decimal portion by 16.
0.25 x 16 oz. = 4 oz.
Total weight = 1 lb.- 4 oz.
4. On a clean walk of driveway, measure out 33.3 feet- the
distance required to cover 100 square feet.
5. Add a measured amount of product to the spreader- 2 to 3
times the recommended rate. Operate spreader at a brisk walking
speed (3 mph of 33.3 feet in 5. sec.) over the measured distance.
Empty the spreader and weigh the amount left. Compare with the
beginning amount; the difference is the amount applied. Adjust the
setting up or down to achieve the correct application rate.
Grease
Oil
Grease
Scotts® is a registered trademark of The Scotts Company
Parts List for Model CD36C
19
24
20
15
24
18
21
17
14
16
13
12
1
22
2
11
3RH
4
6
7
9
5
23
3LH
10
8
ITEM
1
2
3 RH.
3 LH.
4
5
6
7
8
PART #
14211-1
14414-2
14643-1
14644-1
14231
14235
14227
14007
14222-1
90005
14006
15032
12714
12704
14237
14286
12708
15029-1
15046
14047
14870
14415-1
14409
15066
14236
DESCRIPTION
HOPPER ASSEMBLY
SHUTOFF BAR ASSEMBLY*
AGITATOR/AXLE ASSEMBLY-LH. *
AGITATOR/AXLE ASSEMBLY-RH.*
BEARING SUPPORT ASSEMBLY*
AGITATOR BAFFLE* (2)
END HANGER* (2)
AXLE GREASE SEAL* (2)
PLATE ASSEMBLY-BEARING END* (2)
GREASE FITTING* (2)
AXLE BEARING* (2)
WHEEL & TIRE ASSEMBLY (2)
LEG (2)
RATE CONTROL KNOB* (2)
TIE BAR*
SPRING HOUSING ASSEMBLY* (2)
POINTER*
PART OF OUR SERVICE IS PROVIDING
REPLACEMENT PARTS. Parts may be
obtained through your local distributor.
Be sure to give:
1. SPREADER MODEL NUMBER
2. SPREADER NAME
3. PART NUMBER
4. NAME OF PART AS SHOWN
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
IF YOUR LOCAL
DISTRIBUTOR CANNOT
SUPPLY PARTS,
CONTACT:
HANDLE BRACE
UPPER HANDLE ASSEMBLY
HANDLE LEVER ASSEMBLY W/ CHAIN
HANDLE GRIP (2)
CONTROL TUBE
PSB Company
555 West Goodale Street P.O. Box 1089
Columbus, Ohio 43216-1089
614-228-5781 EXT. 2655
CONTROL TUBE BRACE (2)
FASTENER PACKAGE
RATE PLATE* (2)
—
15063
PARTS PACKAGE (NOT SHOWN)
*Parts included in hopper assembly
© 2003 PSB COMPANY
|