INSTRUCTION MANUAL
SW-830XT
SW-830XTP(With pump)
TWIN TUB WASHING MACHINE
IMPORTANT SAFEGUARDS
INSTALLATION
This washing machine has ventilation openings in the base. Do not obstruct the holes with a carpet or towel.
WARNINGS
!
Do not allow your washer to be
repaired by an unqualified service
person.
Be sure to connect POWER PLUG and
POWER CORD properly.
Install on a stable level surface
Install the washing machine on a stable,
level surface.(oblique angle should be
within 2°)
Be sure to plug the POWER CORD
into a proper outlet for the washer.
An improperly attached plug may
catch fire.
Never disconnect by pulling the
cord. Hold the plug as you pull it out.
Never use a damaged POWER CORD.
Never connect and/or disconnect the
POWER PLUG with wet hands, it may
cause an electric shock.
It may cause a risk of accidental
fire.
If the washer operates abnormally,
it may cause injury.
Keep the washing machine more than 5cm
apart from the wall to prevent a noisy sound
while spinning.
If the power cord is damaged, in
order to avoid danger, please ask
a technical person to repair it.
Be sure not to bring any type of
flame near the washer or put lit
cigarettes or volatile materials on
the top of the washer.
It may deform the washer or
catch fire, because this washer
has a large number of plastic
parts.
This appliance is not intended for use by
persons(including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
Connect the DRAIN HOSE
Never let the end of the DRAIN HOSE be
immersed in the water.
Extension of DRAIN HOSE.
<Without pump model>
appliance by a person responsible for their safety.
Shorter than 1m
Do not install the washer in the bath-
room or very humid place.
It may cause a malfunction
or an electric shock.
Never wash items stained with
benzine, kerosene, thinner or
gasoline.
It may cause a risk of fire or
explosion.
Lower than 15cm
<With pump model>
The new hose-sets supplied with
the appliance are to be used and
that old hose-sets should not be
reused.
!
Not higher than 1m
Be sure not to splash or pour
Never put your hand(s) into the
WASH or SPIN TUB, while the
washer is operating.
If you reach into the WASH or
SPIN TUB, it can cause injury.
water on the CONTROL PANEL.
It may cause a malfunction or
an electric shock.
PREPARATION BEFORE WASH
CAUTIONS
!
Do not allow the wash load to stick
out from the WASH or SPIN TUB.
Do not wash, rinse or spin
Do not use water hotter than
50℃.
Be sure to remove things such as
keys, pins and coins from the lau-
ndry.
It may deform plastic parts
Wash oily or dyed laundry
separately.
in the washer and cause a
malfunction.
waterproof clothes or sheets.
Push evenly thick clothes or bulky
wash items completely down into the
WASH or SPIN TUB. Otherwise, it
may deform or damage the washer.
Plug the POWER CORD
Do not put your hand(s) under
the washer during operation.
Do not get on the washer or
put any heavy things on the
washer.
It may deform or damage the
washer, and it may cause
you injury.
into the outlet.
Let down the DRAIN
HOSE.
Connect the INLET HOSE
Rotating parts may cause
injury.
Wash fuzzy laundry by turning it
inside out.
Wash delicate clothes in a
nylon net.
5
2
OPERATING INSTRUCTIONS
MAINTENANCE
Washing
Unplug the POWER CORD
Washing
Time
Kinds of laundry
Wipe the washer clean and dry with
a soft cloth.
after operation.
1. Set the WASH SELECTOR to GENTLE or NORMAL
position.
2. Turn on the water tap, let water flow into the WASH TUB
in accordance with the amount of laundry to be washed.
(The marks H, M, L in tub are High, Medial, Low water
level.)
Synthetic(thin)
Delicate fabrics
2 to 5 min.
Cleaning of the WASH and SPIN TUB
is necessity after bleaching or starching,
otherwise, undesireable deposit will left over.
Cotton
Linen
5 to 10 min.
Remove the LINT FILTER for cleaning.
Heavily soiled clothes
Thick clothes
Blanket
10 to 15 min.
5 min.
3. Add proper amount of detergent.
4. Put laundry into the WASH TUB.
5. Turn the WASH TIMER knob to the desired wash time
position, and washing action will start.
6. When finished, make sure the WASH TIMER is at
the “OFF” position, then turn WASH SELECTOR to
DRAIN position.
TROUBLESHOOTING
Check list
Troubles
OFF
Rinsing
PULSATOR maybe
clogged.
15
5
Not washing
1. Transfer the laundry to the SPIN TUB, and place the SPINNER CAP on the top of laundry.
2. Close the INNER and OUTER SPIN TUB LID.
3. Turn the SPIN TIMER to 1 minute position.
10
WASH TIMER is in
the "OFF"position.
Power failure.
Fuse blown.
4. Transfer the laundry to the WASH TUB after spin drying.
5. Set the WASH SELECTOR to GENTLE or NORMAL position.
6. Let water flow into the WASH TUB and rinse for another 3 to 5 minutes. Repeat it 2 to 3 times.
7. When finish washing, make sure the WASH TIMER is at the “OFF” position, then turn WASH
SELECTOR to DRAIN position.
OFF
5
4
1
2
Not spinning
3
Kinds of laundry
Wool articles
Spin-drying time
30 seconds
Spin drying
SPIN TIMER is in
the "OFF"position.
LID not closed properly.
Laundry not distributed
evenly.
Thin articles(synthetic)
Sweater(synthetic)
Blanket(synthetic)
Underwear(cotton)
Sheet(towel fabric)
1 minute
1 to 3 minutes
3 minutes
1. Transfer the laundry to the SPIN TUB and place
the SPINNER CAP on the top of the laundry.
2. Close the INNER and OUTER SPINNER LID.
3. Turn the SPIN TIMER knob to the desired dry time
position. Then spin-dry will start.
Not drainning
Over load
3 to 5 minutes
5 minutes
DRAIN HOSE is not laid
down correctly.
DRAIN HOSE is
twisted.
DRAIN HOSE frozen.
Make sure water is turned off when spin-drying for safety reason.
Too much laundry in the tub.
Power voltage too low.
Drainning
<Without pump model>
1. Lay down the DRAIN HOSE and turn the WASH SELECTOR to DRAIN.
<With pump model>
Notes for spinning
1. Position the DRAIN HOSE to a wash-basin or drain outlet at the height of lower than 1 meter.
2. Turn the WASH SELECTOR to DRAIN position, and the PUMP will then begins to work to drain away the water.
3. If you wish to drain the water while spinning, turn the SPIN TIMER, and the SPIN TUB will starts rotating and
the pump will starts working at the same time.
Distribute laundry evenly in the
SPIN TUB as shown below.
Put the SPINNER CAP inside
the tub as shown below.
4. If you find the PUMP is working but there is no water drained away, lay down the DRAIN HOSE once, and it
will start draining away the water. Hook the DRAIN HOSE again at the wash-basin or drain outlet.
5. When draining is over, turn off the power.
Laundry
SPIN TUB
X
O
O
X X X
3
4
|