Sanyo Security Camera VCB 3444 User Guide

INSTRUCTION MANUAL  
VCB-3444  
B/W CCD Camera  
About this manual  
Before installing and using the camera, please read this manual  
carefully. Be sure to keep it handy for later reference.  
 
INFORMATION TO USER  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
Safety Guard  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications.  
THIS SYMBOL INDICATES THAT THERE ARE  
IMPORTANT OPERATING AND MAINTENANCE  
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING  
THIS UNIT.  
However, there is no guarantee that interference will not occur in  
a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of  
the following measures:  
WARNING:  
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT  
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
For the customers in Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Pour la clientèle canadienne  
Consult the dealer or an experienced radio/TV technician for help.  
Cet appareil numerique de la Classe B est conforme a la norme  
NMB-003 du Canada.  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause  
undesired operation.  
This installation should be made by a qualified service person and  
should conform to all local codes.  
Changes or modifications not expressly approved by Sanyo may  
void the user’s authority to operate this camera.  
2
English  
 
PRECAUTIONS  
In case of problem  
Protect from humidity and dust  
Do not use the camera if smoke or a strange odour comes from the  
unit, or if it seems not to function correctly. Disconnect the power  
cord immediately, and consult your dealer (or a Sanyo Authorized  
Service Centre).  
To prevent damages to the camera, do not install it where there is  
greasy smoke or steam, where the dampness may get too high, or  
where there is a lot of dust.  
Protect from high temperatures  
Do not open or modify  
Do not install close to stoves, or other heat generating devices, such  
as spotlights, etc., or where it could be subject to direct sunlight, as  
that could cause deformation, discoloration or other damages.  
Do not open the cabinet, as it may be dangerous and cause damage  
to the unit. For internal settings and repairs, consult your dealer (or a  
Sanyo Authorized Service Centre).  
Be careful when installing close to the ceiling, in a kitchen or boiler  
room, as the temperature may raise to high levels.  
Do not put objects inside the unit  
Install where the temperature range will stay between –10˚C and 50˚C.  
(no condensation)  
Make sure that no metal objects or flammable substance get inside  
the camera. If used with a foreign object inside, it could cause a fire,  
short-circuits or damages.  
Cleaning  
If water or a liquid gets inside the camera, disconnect the power cord  
immediately, and consult your dealer (or a Sanyo Authorized Service  
Centre). Be careful to protect the camera from rain, sea water, etc.  
Dirt can be removed from the cabinet by wiping it with a soft  
cloth. To remove stains, wipe with a soft cloth moistened with a  
soft detergent solution and wrung dry, then wipe dry with dry soft  
cloth.  
Be careful when handling the unit  
Do not use benzine, thinner or other chemical product on the  
cabinet, as that may cause deformation and paint peeling. Before  
using a chemical cloth, make sure to read all accompanying  
instructions. Make sure that no plastic or rubber material comes in  
contact with the cabinet for a long period of time, as that may  
cause damage or paint peeling.  
To prevent damages, do not drop the camera or subject it to strong  
shock or vibration.  
Install away from electric or magnetic fields  
If installed close to a TV, radio transmitter, magnet, electric motor,  
transformer, audio speakers the magnetic field they generate will  
distort the image.  
English  
3
 
PARTS NAMES  
1 Power indicator (POWER)  
3 4 5  
Comes on when the power to the camera is on.  
2 Camera setup section  
PAHSE  
2
1
SHUTTER  
VIDEO OUT  
Internal sync (INT)/Line lock (LL) setting  
Electronic iris (EI)/Auto iris (AI) setting  
Backlight compensation (BLC) setting  
Automatic gain control (AGC) setting  
INT  
EI  
BLC  
LL  
AI  
OFF  
OFF  
AGC  
POWER  
AC 24  
V
GND  
3 Line phase adjustment volume (PHASE)  
6
When using two cameras or more, the image on the monitor may roll vertically when switching sources. This  
rolling can be minimized by turning this volume.  
4 High speed electronic shutter switch (SHUTTER)  
7
5 Video output connector (VIDEO OUT: BNC type)  
9
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.  
6 24 V AC input terminal (24 V AC, GND)  
7 Lens iris level volume (LEVEL)  
8
8 Auto-iris lens switch (DC/VIDEO)  
9 Lens iris output connector (LENS)  
4
English  
 
PARTS NAMES  
F Flange-back lock screw  
G Lens mount cap  
The cap is installed to protect the lens mount section.  
Remove the lens mount cap before installing a lens (sold separately).  
F
G
H Camera installation bracket  
The bracket can be fixed at the top or bottom of the camera.  
A Camera mounting screw hole: 1/4"-20 UNC  
CAUTION:  
When installing the camera support, select a location that can support the total weight of the  
camera and accessories.  
H
A
English  
5
 
PARTS NAMES  
Concerning auto-iris lenses  
DC type auto-iris lens  
A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is  
referred to as DC type coil lens or DC type non-amplifier lens.  
H
LEVEL  
(Set the Auto-iris lens switch to the DC position.)  
L
DC  
LENS  
VIDEO type auto-iris lens  
VIDEO  
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is  
referred to as EE amplifier type lens.  
ALC and LEVEL volume level controls are available on the lens for iris adjustments.  
(Set the Auto-iris lens switch to the VIDEO position.)  
Compatible auto-iris lenses  
1/3 inch Sanyo DC type lens  
VCL-CS8LY: Standard angle, f= 8 mm  
VCL-CS4LY: Wide angle, f= 4 mm  
VIDEO type lens  
Standard angle, f= 9 mm  
Telephoto angle, f= 12 mm  
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm  
More telephoto angle, f= 16 mm  
If using a VIDEO type auto-iris lens  
Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned  
all the way to Av (Average).  
Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL  
volume on the lens casing to correct.  
6
English  
 
MOUNTING THE LENS  
Please use a DC type auto-iris lens (sold separately).  
Checking the lens mount  
Do not use a lens if length “L” is more than 9 mm. If not, that may damage the camera and prevent  
proper installation.  
L
Remove the lens mount cap from the camera.  
Install the auto-iris lens.  
CS mount type lens  
1
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.  
C mount type lens  
To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then  
C mount type lens  
carefully align the lens mount with the camera opening and turn the lens slowly to install it.  
2
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.  
When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.  
In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug  
according to the diagram. (Refer to page 8.)  
3
2
CS mount type lens  
English  
7
 
MOUNTING THE LENS  
Rewiring the lens cable in the lens iris plug  
Prepare the lens cable.  
1
2
Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.  
Install the lens iris plug.  
Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close  
the plug cover.  
Pin layout  
DC type lenses  
VIDEO type lenses  
+10 V DC (50 mA max.)  
2
4
1
3
2
4
1
3
Brake coil (–)  
Brake coil (+)  
Drive coil (+)  
Drive coil (–)  
1
2
3
4
Not used  
Video output (1.0 Vp-p, high impedance)  
Ground (for video signal and DC power)  
Flange-back adjustment  
If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus  
(in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back  
position as described below.  
1
Before installing the lens, check that the two flange-back lock screws have been tightened.  
If the flange-back lock screws are loose, the CS mount ring will not be secured and it will not be possible to  
adjust the flange-back.  
2
Fully install the lens, then loosen the two flange-back lock screws.  
Set the zoom lens to the maximum telephoto position (TELE), then set the focus using the focus ring on the lens.  
Set the zoom lens to the maximum wide angle position (WIDE), then set the focus by turning the CS mount ring.  
1, 3  
Repeat steps 3 and 4 until the image stays in focus when changing from a telephoto shot to a wide angle shot.  
When the setting is complete, tighten the two flange-back lock screws.  
8
English  
 
CONNECTIONS  
3
1
(A)  
2
(Video signal connections)  
: VIDEO IN  
: VIDEO OUT  
The peripheral devices (VCR, monitor, lens, etc.) and cables are  
sold separately.  
Insert the plug of this power cord into a wall outlet.  
The POWER indicator (A) will light. Adjust the picture on the  
monitor using the Brightness and Contrast controls.  
Make the video signal connection between the camera and the  
monitor or time lapse VCR.  
Coaxial cable type and maximum length  
Cable type RG-59U (3C-2V), 250 m maximum.  
Cable type RG-6U (5C-2V), 500 m maximum.  
Cable type RG-11U (7C-2V), 600 m maximum.  
Connect to 24 V AC UL listed class 2 power supply (sold separately).  
CAUTION:  
To prevent camera and/or power supply failure, pay close  
attention to polarity when making the connections.  
CAUTION:  
The RG-59U type cable should not be run through electrical  
conduits or through the air.  
To prevent fire hazard any UL listed wire rated VW-1, should be  
used for the 24 V AC cable input terminal.  
Using CCTV/Video-grade coaxial cable.  
English  
9
 
SETTINGS  
Camera setup section  
Iris function setting  
Use a manual or fixed iris lens and set the lens  
aperture to the shortest F stop. Set the EI/AI  
switch to EI position.  
INT  
EI  
BLC  
LL  
AI  
OFF  
EI  
AI  
When using an auto-iris lens (for indoor/outdoor use)  
AGC  
OFF  
Set the EI/AI switch to the AI position.  
Internal sync (INT)/Line lock (LL) setting  
Electronic iris (EI)/Auto iris (AI) setting  
Backlight compensation (BLC) setting  
Automatic gain control (AGC) setting  
Note:  
The electronic iris is suitable for normal indoor use. When the  
EI/AI switch is set to the EI position, do not use an auto-iris lens.  
If used under fluorescent light, the image may flicker. In such a  
case, change to incandescent lighting or set the EI/AI switch to  
the AI position and use an auto-iris lens.  
When shooting bright subjects, pay attention to the light angle in  
order to avoid or minimize the smear phenomenon effect.  
If conditions are outside the electronic iris operation range or more  
than the maximum illumination, it will cause saturation of the CCD.  
In that case, use a manual iris lens.  
10  
English  
 
SETTINGS  
Lens iris adjustment  
Backlight compensation setting  
If using a DC type auto-iris lens, you will need to set the LEVEL  
volume when shooting in the conditions described below.  
Use an auto-iris lens and set the BLC switch to  
the BLC (ON) position, to engage the  
backlight compensation function.  
BLC  
OFF  
L (counterclockwise): To decrease the contrast  
H (clockwise): To increase the contrast  
If shooting simultaneously in a dark room  
and through a bright window.  
If using a VIDEO type auto-iris lens  
H
L
The ALC volume on the lens should be turned all the way to Av  
(Average).  
If the subject background is extremely  
bright or dark.  
LEVEL  
If the backlight compensation function does not compensate  
properly for the conditions, set using the LEVEL volume on the  
lens.  
If the brightness of the picture on the  
monitor is not correct.  
AGC setting  
AGC (Automatic gain control) can be turned ON or OFF.  
AGC (ON): Auto gain control  
AGC  
OFF  
OFF: Fixed gain  
English  
11  
 
SETTINGS  
High speed electronic shutter setting  
Line phase adjustment  
Normally, the speed setting switch for the high  
speed electronic shutter set to the 0 position.  
This sets the electronic shutter speed to 1/60 sec.  
The switch can be set as indicated in table A to  
select one of the 8 speeds available.  
When using a camera switcher to connect 2 cameras or more to one  
monitor, there may be a vertical roll of the images when switched. In  
such a case, set as described below.  
0
6
1
5
2
3
4
7
Set the INT/LL switch to the LL position.  
Switch the display on the monitor from camera 1 to camera 2.  
Adjust the PHASE volume on camera 2 until the vertical roll of the  
image stops.  
If more than two cameras are used, please repeat this procedure  
for all the cameras.  
CAUTION:  
When using the high speed electronic shutter, the EI/AI switch  
must be set to the AI position.  
Using the high speed electronic shutter indoors with low lighting,  
will give darker pictures. In such a case, add some lights to make  
sure the lighting is sufficient. If the lighting is very bright, pay  
attention to the light angle in order to avoid or minimize the  
smear phenomenon effect.  
INT  
LL  
Table A  
0
1
2
3
4
5
6
7
1/60 1/100 1/250 1/500 1/1000 1/2000 1/4000 1/10000  
(Unit: sec.)  
CAUTION:  
If the vertical roll cannot be corrected by setting the PHASE volume  
on camera 2, try setting the PHASE volume on camera 1. If it still  
cannot be corrected, please check that the polarity of the power  
cords of all connected devices is correct.  
12  
English  
 
TROUBLESHOOTING  
Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly,  
please consult your dealer or a Sanyo Authorized Service Centre.  
No picture on the monitor screen  
Is the power turned on to all connected devices? Is the voltage correct?  
Are all the signal connecting cables correctly connected?  
Is the lighting sufficient?  
Has the lens cap been removed?  
Is the lens type (DC or VIDEO) correctly selected?  
Depending on the type of lens, the A. I. LENS switch must be set accordingly.  
Is the iris control correctly set?  
A: When using a DC type lens, the LEVEL volume should be adjusted.  
B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted.  
The picture is not clear  
Is the monitor correctly adjusted?  
Is the flange-back position correctly set?  
Is the lens focus correctly adjusted?  
Are the lens surfaces clean?  
If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens  
cleaning set.  
English  
13  
 
SPECIFICATIONS  
Scanning system  
: EIA standard  
Power supply  
Power consumption  
: 24 V AC, 60 Hz  
(525 TV lines, 30 frames/sec.)  
: 4.0 W (with auto iris lens)  
3.7 W (without auto iris lens)  
: Approx. 560 g (without lens)  
Interlace  
: 2:1 interlace  
Image device  
Picture elements  
: 1/3 inch solid state image device CCD  
: 542 (H) x 494 (V)  
Weight  
Effective picture elements : 512 (H) x 492 (V)  
Synchronizing system  
: Internal sync (INT), Line lock (LL)  
manually switchable  
SERVICE  
This camera is a precision instruments and if treated with care, will  
provide years of satisfactory performance. However, in the event of a  
problem, the owner is advised not to attempt to make repairs or open  
the cabinet. Servicing should always be referred to your dealer or  
Sanyo Authorized Service Centre.  
Resolution  
: 400 TV lines horizontally, 350 TV lines  
vertically  
Video output level  
Video S/N ratio  
Minimum required  
illumination  
(incandescent lighting)  
: 1.0 Vp-p/75 ohms, composite  
: More than 50 dB  
: Approx. 0.05 lux with a F 1.2 lens,  
Approx. 0.07 lux with a F 1.4 lens  
Backlight compensation  
: Manual ON/OFF switching, zone light  
measuring system  
(Active when using an auto-iris lens)  
Iris function  
High speed electronic  
shutter  
: Manual ON (EI)/OFF (AI) switching  
: 8 speeds, selectable by switch:  
(1/60, 1/100, 1/250, 1/500, 1/1000,  
1/2000, 1/4000, 1/10000 sec.)  
Electronic iris range  
: 0.07 lux to 42,000 (F 1.4, lens)  
0.05 lux to 30,000 (F 1.2, lens)  
Flange-back  
AGC  
Gamma correction  
Lens mount  
: 12.5 mm ± 0.8 mm  
: Manual ON/OFF switching  
: γ = 0.45  
: CS mount  
Environmental conditions : Temperature: –10˚C ~ +50˚C  
Humidity: less than 90% (no  
condensation)  
14  
English  
 
SPECIFICATIONS  
ACCESSORIES  
Dimensions  
1 Lens iris plug (4-pin)..................................................................1 pc.  
2 Hexagonal wrench....................................................................1 pc.  
60  
135  
123  
7
1
2
PHASE  
SHUTTER  
VIDEO OUT  
INT  
EI  
BLC  
AGC  
LL  
AI  
OFF  
OFF  
60  
POWER  
GND  
AC 24V  
11  
29  
1/4”–20 UNC  
40  
28  
Features and specifications are subject to change without prior  
notice or obligations.  
English  
15  
 
SANYO INDUSTRIAL VIDEO  
B/W VIDEO CAMERA LIMITED WARRANTY  
OBLIGATIONS  
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and  
addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.  
For product operation, authorized service center referral, service assistance or problem resolution, call  
CUSTOMER INFORMATION 1-800-421-5013  
Weekdays 8:30 AM – 5:00 PM Pacific Time  
For accessories and/or parts, call  
PARTS ORDER INFORMATION 1-800-726-9662  
Weekdays 8:30 AM – 5:00 PM Pacific Time  
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES  
ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER  
AT THE TIME WARRANTY SERVICE IS REQUESTED.  
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or  
replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.  
LABOR  
3 YEARS  
PARTS  
3 YEARS  
IMAGE DEVICE  
3 YEARS  
EXCLUSIONS  
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered, defaced  
or removed.  
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.  
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.  
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized  
service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,  
flood or other Acts of God, or normal wear and tear.  
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.  
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE  
FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS  
WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH  
THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR’S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT,  
SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.  
ATTENTION  
For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.  
Model No._____________________________________________________________________  
Date of Purchase _______________________________________________________________  
Serial No. _____________________________________________________________________  
(Located on back or bottom side of unit.)  
Purchase Price _________________________________________________________________  
Where Purchased _________________________________________________________________________________________________________________________________________________  
 
1AC6P1P2433--  
L73Q4/US(0501KP-TVS)  
98230002  
21605 Plummer Street,  
Chatsworth, California 91311  
Printed in Taiwan  
 

Pyramid Car Audio Musical Instrument Amplifier GA610 User Guide
Raymarine GPS Receiver ST6001 User Guide
RCA Car Video System 811 727191W030 User Guide
ResMed Ventilation Hood 2011 09 User Guide
Roadmaster Car Stereo System MP320 User Guide
Rolls Power Supply PS16 User Guide
Schumacher Battery Charger INC 14825A User Guide
Seagate Computer Drive ST1200MM0007 User Guide
Seal a Meal Food Saver VS240 User Guide
Sears Air Compressor 92116471 User Guide