Owner’s Instructions
SW51ASP/SW61ASP
CONTENTS
Page
FEATURES ............................................................................................1
DESCRIPTION OF PARTS....................................................................2
SAFETY INSTRUCTIONS .....................................................................3
INSTALLATION & MAINTENANCE......................................................4
ENVIRONMENT................................................................................4
IN CASE OF PUMP-DRAINED WASHER .......................................4
HOW TO CONNECT WATER SUPPLY HOSE ................................4
CLEANING THE FILTER NET..........................................................5
HOW TO ADD THE FABRIC SOFTENER.......................................5
HOW TO PUT THE DETERGENT IN ..............................................5
CLEANING THE FILTER ..................................................................5
LEVELLING.......................................................................................5
PRECAUTIONS ................................................................................6
TO DO A CLEAN WASHING ...........................................................6
WASHING INSTRUCTION.....................................................................6
PROCEDURE ...................................................................................6
WASH PROGRAM............................................................................7
WASHING PROGRAM DETAILS..........................................................7
OPTIONAL CYCLE................................................................................8
TROUBLESHOOTING...........................................................................8
SPECIFICATION
DESCRIPTION OF PARTS
CONTROL PANEL
2
SAFETY INSTRUCTIONS
WARNING!
To reduce the risk of fire, electric shock, or injury to persons when using your appliance,
take care to adhere to the following precautions.
● Where an unearthed power cord is not fitted,
be sure that the washer is grounded.
To avoid electrical shock use metal piping for the ground
connection.
● Maximum hot water supply temperature
60 degrees.
Take care not to ground the washer to gas pipes or
telephone cables due to the danger of explosion from
lightning strikes.
●● Before washing, check all pockets.
If nails or pins remain in pockets, they may damage the
washer or clothes.
● During spinning, don't put your
hand in the spin basket.
Because the spin basket is rotating at the
high speed, rotating parts may injure your
hand.
● Don’t press the control panel with a sharp
object.
Panel damaged or malfunction may occur.
If the control panel for this washer is damaged,
it must be replaced by a repair shop appointed by the
manufacturer, as special purpose tools are required.
● Openings must not be obstructed by carpeting
when the washing machine is installed on a
carpeted floor.
●● Do not operate this appliance if it is damaged,
malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged
cord or plug.
● Turn off water taps when the washer is not in
use to avoid water pressure damage to the
pump.
● Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
● To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
● The instructions for use shall specify the
maximum mass or dry cloth in kg, for which the
appliance is designed.
attempting any maintenance or cleaning.
● The appliance is not intended for use by young
children or infirm persons without supervision.
● If the appliance is supplied from a cord
extension set or electrical portable outlet
device the cord extension set or electrical
portable outlet device should be positioned so
it is not subject to splashing or ingress of
moisture.
● Young children should be supervised to ensure
that they do not play with the appliance.
● This appliance is not intended for use by young
children or infirm persons unless they have
been adequately supervised by a responsible
person to ensure that they can use the
appliance safely.
● If the power supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avoid a hazard.
Young children should be supervised to ensure
that they do not play with the appliance.
● Place clothes evenly into the washer as
unevenly distributed laundry may cause
excessive out-of-balance noise and vibration.
3
INSTALLATION & MAINTENANCE
IN CASE OF PUMP-DRAINED WASHER
ENVIRONMENT
●
Take out the ●●Be sure to join tightly ●●Install the drain
Leave some space
Maintain at least 10cm between the washer and the
wall.
cap-hose and
connect the
outlet-hose.
the drain hose into the
drain-outlet on the left
side of the machine.
hose in the position
of about 70~80cm
above the ground.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak
surface, noise or vibration occurs. (Allowable slope
is 1 degree)
cap-hose
outlet-hose
Never install the washer in a very steamy
environment or where it might be open to
the rain.
Excessive moisture may cause an electrical shock
hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by
direct heat,never place the washer near furnaces,
boilers,etc. Do not place under direct sunlight.
HOW TO CONNECT WATER SUPPLY HOSE
Check the type of tap fitting which is in your laundry and then see appropriate instruction below:
A tap of ordinary type is desirable
In case of square tap
●
Take out the internal part of the connector
and join it in the following way.
Internal part
ORDINARY TAP
SQUARE TAP
ROTATING TAP
4. Connect the water supply hose
1. Remove the adaptor from the
water supply hose.
to the adaptor. Pull down the
part (c) of the water supply
hose. When you release part (c)
the hose is automatically
connects to the adaptor making
a 'click' sound.
c
2. First,using a "+" type screw
driver, loosen the four screws
on the adaptor. Next,take the
adaptor and turn part(b)
following the arrow for gap
about 5mm between them.
5. Connect the other end of the
water supply hose to the inlet
water valve at the top of the
washer.
Screw the hose clockwise all
the way in.
a
b
6. If the water tap is a screw
type,assemble a water supply
hose that fits to the tap as
shown.
3. Connect adaptor to the water
tap by tightening the screws
firmly.
Then,turn part (b) following the
arrow and put (a) and (b)
together.
c
Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not
be used.
4
CLEANING THE FILTER NET
1.Push the upper part of
the filter and pull in.
2.Open the cover as
shown in the figure.
3.Clean the filter.
4. Close the cover and insert the lower
part of the filter in the basket first and
then push the filter with "click" sound .
HOW TO ADD THE FABRIC SOFTENER
•
When a proper amount (one time does) of fabric
softener is stored in the softener inlet,it is
automatically put in at the last rinsing cycle.
Do not use detergent, bleach or starch into
the Softener Inlet.
•
•
Do not open the lid during the Spin Dry cycle.
If added too early, its effectiveness will decrease.
Do not leave the softener
into the Softener
Dispenser for a long time.
Because softner
•
•
Using too much softener may produce
unsatisfactory results.
became stiff.
HOW TO PUT THE DETERGENT IN
1. Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent in
the detergent box.
2. Put in one-time amount of detergent evenly so the detergent may not brim over the box.
Detergent Device
Put the detergent
in proportion to
water level
Softener Device
Softener
baseline
CAUTION : If softener is stored over the above base line, it may flow down at any time.
CLEANING THE FILTER
(pump drained washer)
LEVELLING
•
If the washer is not leveled with the ground, it makes the machine
tremble more or be out of order. So, make sure that the washer is
leveled properly.
1. Place a rag under washer filter not to wet the floor.
2. Turn the filter-cap to the left.
3. Take out the filter and remove any sludge.
4. Reassemble in reverse order.
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING
THE POSITION OF THE WASHING TUB.
• Open the lid of the machine, pour water into the tub up to the level
just below the pulsator, and adjust the legs so that the pulsator is
positioned at the center of the water as shown in the figure.
Water
•
•
Place the machine more than
10cm away from the wall.
Adjust the legs on feet
for levelling .
Loosen
Lock
5
WARNING! NOTE THE FOLLOWING PRECAUTIONS TO PREVENT ELECTRICITY
LEAKAGE AND THE POSSIBILITY OF ELECTRIC SHOCK.
Earthing is necessary to prevent leakage or electric shocks caused by the electric currents leaked from the machine.
How to earth an outlet with earthing terminals when
an earthed power load is not fitted.
Outlet with earthing terminals:
● Even when the internal wires of the earthing terminals are joined,
connect the earthing conductor (green) of the machine to the tap.
When using an extension cord and a boosting transformer:
● Make sure that the earthing conductor is connected.
Never make an earthing to
● The telephone line, lightning rod, or gas pipe as it is
extremely dangerous in case of lightning strikes.
TO DO A CLEAN WASHING
•
•
•
•
•
Press the POWER botton.
Pour a little detergent into case-detergent.
Turn on water supply to the wshing machine.
Choose the SOAK in CYCLE button and the HIGH in WATER LEVEL button.
Press the START/PAUSE button.
WASHING INSTRUCTION
PROCEDURE
1
. Sort the laundry into separate wash loads.
Each load of washing should contain clothing which needs the same washing conditions.
For example, you should not wash delicate clothes with very dirty work clothes.
2
. Load the laundry into washing.
Before load, check all pockets, and close zippers, hooks and eyes.
3. Add the detergent. (see page 5)
4. Add the fabric softener. (see page 5)
5. Close the lid.
6. Press power button.
7. Choose the wash program & optional cycle. (see page 7~8)
If you choose “SENSOR” program you don’t need to select water level.
Water level is set automatically at “SENSOR” program.
Press the START/PAUSE button.
8. Select the water level.
Before choosing the water level, remember following things.
When you choose SENSOR, HEAVY-DUTY, ECONO-WASH, WOOL program,
water level is selected “AUTO” automatically, but if you wat to choose water level manually
you can select. HIGH, MEDIUM, LOW, MINIMUM
6
9
. Select the water temperature.
Before choosing the water temperature remember the following:
• You can choose COLD → COLD+HOT → HOT on all programs.
HOT is hot wash and cold rinse.
COLD is cold wash and cold rinse.
10. Close the lid and press the START/PAUSE button.
11. Do you wat extra rinse?
For extra rinses press the cycle key 1 to 5 times (depending on the number of extra rinse required).
You can select up to 5 extra rinses or return to a single rinse by pressing the cycle key.
The time left display will show the number of rinses selected.
Note tat the extra rinse program is not available when pause is selected or during the spin cycle.
WASH PROGRAM
SENSOR
25 min
HEAVY DUTY
26 min
ECONO WASH
5 min
WOOL
5 min
Wash Time (SW51ASP)
Wash Time (SW61ASP)
Wash Action
20 min
20 min
5 min
5 min
Normal
Normal
Normal
Gentle
HOT
HOT
HOT
Wash Temp.
HOT + COLD
COLD
HOT + COLD
COLD
HOT + COLD
COLD
HOT + COLD
COLD
HOT + COLD
COLD
Deep Rinse
Spin Time
COLD
COLD
COLD
3 min
5 min
7 min
1 min
Total Time
(High Water level)
32 min
29 min
49 min
49 min
WASHING PROGRAM
SENSOR Program
HEAVY DUTY Program
●
●
The best washing program is chosen automatically
Load size and water level is determined automatically
●
●
This program is suitable for heavily soiled laundry
Load size and water level is determined automatically
or you can choose the water level you want
●
Unplug the power cord after washing.
●
Unplug the power cord after washing.
ECONO WASH Program
WOOL Program
●
●
●
Saving your time and energy
●
●
This program is suitable for woollen clothes
This program is suitable for heavily soiled laundry
Load size and water level is determined automatically
or you can choose the water level you want
Only high and medium water levels are available
●
Unplug the power cord after washing.
●
Unplug the power cord after washing.
7
OPTIONAL CYCLE
WASH ONLY
RINSE ONLY
●
●
When you choose this cycle, wash cycle is operated.
Pressing optional cycle key during washing changes
the wash time in two minute intervals.
The wash time can be changed to between 3 and 25
minutes.
●
When you choose this function, only rinse cycle is
operated.
●
Pressing function key during rinsing changes the
number of rinse. Up to 5 rinses can be optionally
selected.
●
●
Load size and water level is determined automatically
●
● Unplug the power cord after washing.
Unplug the power cord after washing.
SOAK
RINSE AND SPIN ONLY
●
●
●
The laundry is soaked in water so that heavy dirt can be
●
When you choose this cycle, only rinse & spin cycle are
operated without wash cycle.
eliminated sufficiently.
You can choose soak cycle after choosing wash
program.
When you select soak function, 5 minute cycle (1 min.
washing then 4 min. pause) continue for 30 minutes
before main wash program.
●
Pressing cycle key during operation changes the
number of rinse (see above).
You cannot change the spin dry time using this function.
●
Unplug the power cord after washing.
●
Load size and water level is determined automatically
●
Unplug the power cord after washing.
SPIN ONLY
DELAY START
●
●
You can choose this cycle, only cycle is operated.
Pressing cycle key during spinning only cycle changes
the spin dry time.
●
This function allows you to delay the start of your
chosen wash program for 3, 4, ... 18 hours.
By pressing the delay start key you can select delayed
period for 3, 4, ... 17, 18 hours, and your washing
machine will finish the selected wash program after the
delayed period.
●
The spin dry time can be changed to between 1 and 7
minutes.
●
Unplug the power cord after washing.
TROUBLESHOOTING
Washing machine won’t work
Spinning does not work
Is the water tap opened?
Is the washer plugged in?
Is the power cut off?
Is the laundry spread out evenly
in the washer?
Is the washer set on a sturdy
flat surface?
Is the fuse all right?
Is there enough water?
Is the lid closed?
Water does not drain
Water is not supplied
Is the drain hose down? (No pump)
Is the drain hose frozen?
Is the water tap opened?
Is the water cut off?
Is the drain hose clogged?
Is the water supply hose or
If the water does not drain in 15
minutes, a buzzer will sound, and the
remaining time indicator will show “5E”
hose connection clogged?
Is the water tap frozen?
If water is not supplied in 60 minutes,
a buzzer will sound, and the remaining
time indicator will shown “4E”.
While lid is opening,
the washing machine won’t work
Make sure to close the lid while washing machine is
operating.
8
IF YOU NEED HELP WITH YOUR NEW
SAMSUNG WASHING MACHINE
Contact your nearest Samsung office or Samsung authorized
service center for technical assistance
SPECIFICATION
SW51ASP
330
SW61ASP
426
Power input(Watts)
Load capacity(kg)
5.0
6.0
Size(WxDxH)(mm)
540 X 560 X 850
31
588 X 618 X 955
38
Net Weight(kg)
Water Consumption(liters)
Water Pressure(min-max)
106(high)
50~780KPa
138(high)
50~780KPa
CODE NO. : DC68-01488E
|