OPERATOR'S MANUAL
Miter Slot Table
4060310
(For use with BT3000 & BT3100 Table Saws)
Your new miter slot table has been engineered and manufactured to Ryobi's high standard for dependability, ease
of operation and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual.
Thank you for buying a Ryobi accessory kit.
SAVE THIS MANUAL FOR FUTURE REFERENCE
UNPACKING
INFORMATION
WARNING:
If any parts are missing, replace the missing parts
before assembling the kit. Failure to do so could
result in serious personal injury.
■ Remove the loose parts from the box. Make sure
that all items listed in the loose parts list are in-
cluded .
■ Inspect all parts carefully to make sure no breakage
or damage occurred during shipping.
LOOSE PARTS LIST
1. Miter Slot Table
■ If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
2. Shims (4)
3. 1/4-20 x 1 in. Hex Head Cap Screws (2)
4. Washers (2)
5. 1/4-20 Hex Nuts (2)
MITER SLOT TABLE
1/4-20 x 1 in.
HEX CAP SCREW
WASHER
SHIM
1/4-20 HEX NUT
Fig. 1
3
TOOLS NEEDED
7/16 in. NUT DRIVER
3/16 in. HEX KEY
Fig. 2
ASSEMBLY
INSTALLING THE MITER SLOT TABLE
See Figure 3.
WARNING:
The table saw should never be connected to a power
supply while you are assembling parts. Disconnect-
ing the table saw will prevent accidental starting that
could cause serious personal injury.
■ Turn the ON/OFF switch to the OFF position.
■ Unplug the saw from the switched on-board outlet.
■ Disconnect the saw from the power supply.
■ Remove the sliding miter table and accessory table
from the saw.
■ Place the miter slot table onto the saw as shown in
Figure 3.
1/4-20 x 1 in.
HEX CAP SCREW
MITER
SLOT TABLE
SHIMS
WASHER
1/4-20 NUT
Fig. 3
4
ASSEMBLY
REAR VIEW
1/4-20 x 1 in.
HEX CAP SCREW
MITER
SLOT TABLE
PLACE SHIMS
AS SHOWN
SHIMS
WASHER
1/4-20 NUT
FRONT VIEW
Fig. 4
ALIGNING THE MITER SLOT TABLE
See Figure 4.
MITER
SLOT TABLE
1/4-20 x 1 in.
HEX CAP SCREW
■ Place the miter slot table on the saw as shown in
Figure 4.
■ Extend a straight edge across the saw table onto
the miter slot table and note any space between the
straight edge and the miter slot table. If space ex-
ists, place one of the shims under the miter slot
table and recheck. Add shims as required between
the miter slot table and the saw table to allow the
miter slot table to be flush with or slightly lower than
the saw table. Repeat the process for the rear of the
miter slot table. Recheck in front and rear to assure
that the miter slot table is not above the surface of
the saw table.
WASHER
SHIM
1/4-20 NUT
Fig. 5
■ Place mounting bolts with washers through holes in
the miter slot table and the saw table frame as
shown in Figure 5. Place a nut under the lip of the
saw frame on each bolt. Tighten firmly and evenly.
Shims will be secured when you tighten the screws.
■ Replace the sliding miter table and the accessory
table.
NOTE: The miter slot table must not be higher than the
saw table.
5
OPERATOR'S MANUAL
Miter Slot Table
4060310
WARRANTY
Ryobi warrants its accessories for a period of 90 days from the date of purchase. Batteries and chargers are
warranted for a period of two years from the date of purchase.
PARTS AND SERVICE
For parts or service, contact your nearest Ryobi authorized service center. Be sure to
provide all relevant information when you call or visit. For the location of the authorized
service center nearest you, please call 1-800-525-2579 or visit us online at
MODEL NUMBER
4060310
RYOBI TECHNOLOGIES INC.
1428 Pearman Dairy Road Anderson, SC 29625
Post Office Box 1207
1-800-525-2579
Anderson, SC 29622
972000-353
|