PowerPress
Instructions for Use
D E F
G
H
C
B
I
J
A
L
A
C
I
T
R
E
V
M
L
K
■ Description:
A Spray nozzle
G Flexible cord protector
H Power cord
B
Water filling inlet
C Variable steam control
with self clean system
D Spray button
I
Pilot light
J
Temperature control dial
Stainless steel soleplate
Transparent water tank
K
L
E
F
Burst of steam button
Auto-off indicator light
M Water level indicator
Rowenta Werke GmbH
63016 Offenbach am Main
BEFORE USE
Please read the instructions for use and the Important
Safeguards carefully.
Remove the sticker or transparent soleplate protector.
It is normal for a small amount of smoke to be produced
the first time the iron is used. This will quickly disappear.
˾
˾
˾
ᕡ 3-WAY AUTO-OFF
If the iron is not moved while it is
plugged in, an internal safety switch
will turn it off. It will turn off in 8 min-
utes if left vertically or in 30 seconds if
left on its soleplate or tipped over. A
red flashing light indicates that the
auto-off has been activated. To switch
the iron on again, move the iron or
gently shake it. Wait until iron is fully
reheated before use.
1
30 sec.
TI
VER
C
AL
V
E
R
T
I
8 min.
30 sec.
C
A
L
Auto-off is not an on/off switch. Always unplug the iron
when it is not in use.
ᕢ STEAM IRONING
2
Filling with water
Ensure the iron is unplugged.
Slide the variable steam control
completely to the left.
˾
˾
Hold the appliance upright so that
the water inlet is horizontal.
˾
˾
Fill with water (containing no addi-
tives) to the max. water level mark.
Adding water
If you need to add water during ironing UNPLUG the iron
and repeat above steps.
˾
˾
˾
Ensure iron is fully reheated after filling (pilot light goes out)
before ironing.
To avoid damage to clothes from dust or dirt that may
collect in the iron, we recommend that for the first use or
after the iron has been stored for some time that you first
iron an old cloth that can be discarded, testing both the
steam and burst of steam features.
ᕣ SELECTING THE TEMPERATURE
Set the temperature control dial
3
according to the type of fabric you
are ironing.
Check the fabric's label for appro-
priate setting.
Laundry
label
Fabric
Temperature
setting
Synthetics
Nylon
Polyester
●
(low temperature)
Silk
Wool
●●
(medium temperature)
Cotton
Linen
●●●
(high temperature)
To avoid an automatic switch off while the iron is heating
up, always keep the iron on its heel.
˾
˾
˾
˾
Start at a low temperature and graduate to a high tempera-
ture.
For delicate fabrics we recommend carrying out a test on
an unobtrusive part of the garment (inner seam).
Steam can only be produced when the thermostat is in
the red cotton/linen zone.
ᕤ SETTING THE VARIABLE STEAM CONTROL
Set the variable steam control to
4
required steam volume. Steam can
only be produced when the thermo-
stat is aligned to ●●● (red zone on
dial). (If on setting ● or ●● the vari-
able steam lever should be shut off.)
Allow iron to heat up (light goes
out) before activating the steam
control.
f
l
e
C
S
n
a
le
mi
n
x
ma
Iron ready for steam ironing
Steam is produced as soon as the iron is held horizontally and
variable steam lever is moved from the min position.
Steam off
Steam generation can be interrupted by standing the iron on
its heel or sliding the variable steam control fully to the left
(min.)
ANTI-DRIP SYSTEM
(Depending on model)
In order to produce steam, all irons require a high tempera-
ture. If the soleplate is not hot enough some of the water will
not turn to steam and can spit or leak from soleplate. The anti-
drip system automatically reduces the volume of steam when
ironing at low temperatures to prevent dripping.
ᕥ SPRAY SETTING
˾ Ensure there is water in the tank.
5
˾ Moistening the fabric with the
spray will make wrinkle removal
easier. This is very useful when the
three dot setting is too hot for the
material being ironed.
˾ Press the spray button down slowly
for a jet or quickly for a mist.
˾ Do not spray silk, etc.
ᕦ BURST OF STEAM
To remove stubborn wrinkles or
press in a sharp crease, use the
burst of steam button.
Press the button firmly, a strong
burst of steam penetrates deep
into the fabric.
Leave an interval of at least four
seconds between pressing the
burst of steam button.
With water in the tank, the burst of
steam button can be used as soon
as the steam ironing temperature
has been reached (●●●).
˾
˾
˾
˾
6
ᕧ VERTICAL STEAM
The iron can also be used vertically.
This is especially useful for getting
creases out of hanging clothes,
curtains, tapestries, etc.
To steam vertically, press the burst
of steam button while holding iron
in the upright position.
˾
˾
7
Warning:
Never iron clothes while they are being worn.
POINTS TO NOTE
If the iron has not been used for a long time (e.g. several
weeks) the steam channels should be cleaned and any
deposits removed from the iron. To do this, hold the iron
horizontally before you start to use it and allow it to produce
steam for about 1 minute. Also activate the burst of steam
button several times.
ᕨ DRY IRONING
Slide the variable steam control
fully to the left (min.). We recom-
mend dry ironing with an empty
water tank to be sure there are no
drips.
˾
8
f
l
e
C
S
n
a
le
mi
n
x
ma
AFTER IRONING
Unplug the iron. Set the variable steam control to max.
and empty any water left in the tank. Then set the variable
steam control to min. and leave the iron to cool.
˾
For easy storage the cord can be wound loosely around the
heel once the iron has cooled down completely.
˾
˾
To protect the soleplate always store the iron on its heel.
Important:
Always empty the water tank when ironing is finished.
WATER TO USE IN ROWENTA IRONS
Tap water
Rowenta irons are designed to be used with REGULAR TAP
WATER (up to 12 grains of hardness). If your water is harder
than this, Rowenta recommends mixing half tap water with
half distilled water which reduces the hardness; or use just
inexpensive bottled spring water.
Never use 100% distilled water since this can cause the
iron to spit and leak.
Softened water
There are many types of household water softeners and the
water from many of them is perfectly acceptable for use in an
iron. However, some types of softeners, particularly those that
use chemicals such as salt, can cause the iron to leak or spit
during use. If you experience this type of problem we recom-
mend trying inexpensive bottled spring water or untreated tap
water.
Never use 100% pure distilled water.
Once you have changed water it will take several uses to
correct the problem. Rowenta recommends trying the steam
function for the first time on an old towel or cloth that can be
thrown away to avoid damaging clothes.
Iron and other impurities
If your water supply contains large amounts of iron or organic
matter, these minerals can collect inside the iron and eventual-
ly appear as brown stains. If you experience these issues, we
recommend trying inexpensive bottled spring water.
Never use 100% pure distilled water.
Always remember:
Battery water and water containing additives (such as starch,
perfume or fabric onditioner) may not be used in the iron.
Such additives can affect the properties of the steam and, at
high temperatures, can form deposits in the steam chamber.
These deposits can mark laundry when they are emitted
through the steam vents. For this reason, descaling liquids
should not be used.
ᕩ SELF CLEANING
Your iron is equipped with two self
clean functions.
˾
9
f
l
e
C
S
n
a
le
mi
n
x
ma
Vapodur Valve
The patented Vapodur valve ensures that the opening
which allows the water to drip from the tank into the steam
chamber remains unaffected by hard water deposits.
To ensure that your iron continues to steam efficiently the
valve MUST be opened and closed a few times after each
use. This is done by moving the variable steam control left
to right a few times.
˾
˾
Steam Chamber Cleaning Function
This function allows loose mineral deposits and other
impurities that build up inside the iron to be flushed out. This
type of self cleaning only needs to be carried out occasionally
and never more than once a month.
Fill the iron with cold tap water halfway to the max line and
set variable steam lever to min.
˾
Stand on heel and plug in.
˾
˾
˾
Set thermostat dial to maximum (●●●) position.
When the iron reaches the correct temperature, indicator
light will go out, unplug iron.
Hold iron horizontally over the sink with soleplate pointing
away from the body.
Move variable steam lever completely to the right and hold
in self clean position for one minute.
˾
˾
WARNING:
Doing this will cause steam and hot water to be ejected
from the soleplate. Take all proper preacautions and hold
iron away from body.
Move the iron gently back and forth and side to side until
all water has run through.
Carefully wipe all water and material from the soleplate
with an old towel, as the water and minerals can stain the
soleplate (although this has no effect on glide or
performance).
˾
˾
WARNING:
Iron and soleplate may still be hot, exercise care while
wiping.
Place iron on heel and leave to cool.
˾
˾
IMPORTANT: Before using the iron after self cleaning, test
steam and burst of steam on an old towel or cloth that can
be discarded to ensure all loose material have been
removed from the iron.
CLEANING AND MAINTENANCE
When cold and unplugged, the iron can be cleaned with a
damp cloth and wiped dry. Never use household cleaners
or solvents.
˾
Cleaning the soleplate
Rowenta soleplates have excellent non-stick properties and
can be simply wiped clean when cold.
In normal use a draggy coating may build up on the sole-
plate (starch, detergent buildup, burnt synthetic fibers).
This can be easily removed by using the Rowenta Soleplate
Cleaning Kit or a quality hot iron cleaner available at most
stores.
˾
Do not use abrasive household cleaners or abrasive cleaning
pads.
˾
˾
The soleplate of your iron makes ironing easier. To prevent
scratching of the soleplate, do not iron over sharp objects
(zippers, etc.). Do not place the iron on rough surfaces, e.g.
metal iron support, which may scratch the plate.
IRON TROUBLESHOOTING
Problem
Possible cause
Solution
Iron is
leaking.
DISTILLED WATER
DO NOT use 100% pure distilled
water, use tap water. In very hard
water areas mix half tap water with
half distilled to reduce hardness; or
use inexpensive bottled spring
water.
SOFTENED WATER Most softened water is alright, but
if you experience leaks or spitting,
change to untreated tap water or
inexpensive bottled spring water.
DO NOT use 100% distilled water.
Auto-off activated? Move iron or gently shake.
Overuse of burst of Allow more time between each
steam.
burst.
Iron won’t Is iron plugged in? Check plug is in socket.
heat.
Thermostat set too Turn thermostat higher.
low?
Auto-off activated? Move iron or gently shake.
Ready light This is normal.
goes on
and off.
The light goes on and off showing
the thermostat is switching the heat
on and off to maintain the correct
temperature.
Iron does Iron is not hot
not steam. enough.
If the iron is not hot enough the
anti-drip system will activate and
stop the iron's steam production.
Set thermostat to the (●●●)
position.
Is variable steam
If iron is fitted with a variable steam
control correctly set? control, turn it to a higher setting.
Steam valve is
clogged.
Move variable steam controm from
min to max several times to clear
blockage.
In the interest of improving products, Rowenta reserves the
right to change specifications without prior notice.
LIMITED WARRANTY
All Rowenta products are warranted for 1 year from date
of purchase against defects in material and workmanship.
During this period, any Rowenta product that, upon
inspection by Rowenta, is proved defective, will be repaired
or replaced, at Rowenta's option, without charge to the
customer. If a replacement product is sent, it will carry the
remaining warranty of the original product. This warranty
does not apply to any defect arising from a buyer's or
user's misuse of the product, negligence, failure to follow
Rowenta's instructions, use on current or voltage other
than stamped on the product or alteration or repair not
authorized by Rowenta. Repair or disassembly by anyone
other than a Rowenta authorized service center will void
the warranty. THE WARRANTIES SET FORTH HEREIN ARE
EXCLUSIVE AND NOT OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR USE, ARE MADE BY ROWENTA
OR ARE AUTHORIZED TO BE MADE WITH RESPECT TO
THE PRODUCT. If you believe your product is defective,
bring the product (or send it, postage prepaid) along with
proof of purchase to the nearest authorized Rowenta
Service Center (see below). If you send the product, please
include a letter explaining the nature of the claimed defect.
Rowenta Inc.
196 Boston Avenue
Medford, MA 02155 U.S.A.
Tel.: (781)396-0600
OFFICE LOCATION ONLY.
If your appliance needs service, ship the product to your
nearest regional service center. If in warranty, Rowenta will
repair or replace product at their discretion. If the product is
out of warranty, you will advised of the cost of repair before
any work begins.
Our main service centers are listed below.
Turnpike Appliance
3495A Lawson Blvd.
Oceanside, NY 11572
516-483-5596
Authorized Appliance
1644 West Ogden Ave.
Downers Grove, IL 60515
630-852-1550
Service center information is subject to change. Please visit
our website at www.rowentausa.com or call our service center
information line at 781-306-4620. The information line
provides current service center information and listings in
California.
|