VISTA MINI
DESKTOP KVM SWITCH WITH AUDIO
Installation and
Operation Manual
ELECTRONICS
10707 Stancliff Road n Houston, Texas 77099
TABLE OF CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . 1
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . 1
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 2
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . 2
Vista Mini models . . . . . . . . . . . . . . . . . . . . . . . . . 2
Locating the unit . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Cable requirements . . . . . . . . . . . . . . . . . . . . . . . . 2
VIStA MINI HARDWARE . . . . . . . . . . . . . . . . . . . 4
The front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
The connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 6
Step1. Connecting monitor,keyboard, mouse,andspeakers . . . . 6
Step 2. Connecting the computers . . . . . . . . . . . . . . . . 6
Step 3. Powering up the system. . . . . . . . . . . . . . . . . . 7
Step 4. Switching from the keyboard . . . . . . . . . . . . . . . 7
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . 8
Keyboard computer selection . . . . . . . . . . . . . . . . . . . 8
Going to the next or previous computer . . . . . . . . . . . . . . 8
Scan mode commands . . . . . . . . . . . . . . . . . . . . . . 8
Scan time interval command . . . . . . . . . . . . . . . . . . . 9
Mode command . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Typematic value command . . . . . . . . . . . . . . . . . . . 10
PS/2 to serial mouse translation, wheel mouse . . . . . . . . . 11
Keep command . . . . . . . . . . . . . . . . . . . . . . . . . 11
Null command . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ROM Identification command . . . . . . . . . . . . . . . . . . 12
Reset command . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reset computer mouse command . . . . . . . . . . . . . . . . 12
Reset to factory default . . . . . . . . . . . . . . . . . . . . . . 13
KEYBOARD COMMAND SUMMARY. . . . . . . . . . . . . 14
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . 16
SERVICE INFORMATION . . . . . . . . . . . . . . . . . . 16
Appendix A.
Appendix B.
Factory default settings . . . . . . . . . . . 18
General specifications . . . . . . . . . . . 18
Appendix C. Cables and accessories . . . . . . . . . . . 19
INTRODUCTION
Thank you for choosing Vista Mini™. Designed for plug-and-play operation,
your new Vista Mini switch simplifies your job by helping you organize your mul-
tiple computer applications. Because Vista Mini lets you use a single keyboard,
monitor, mouse, and speakers to access two computers, you can significantly
reduce your equipment overhead and end keyboard and monitor clutter.
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Access 2 computers with one keyboard, monitor, mouse, and speakers
Low cost and easy to use
Small size (.8" high by 3.2" wide by 4.2" deep)
Saves physical space, equipment and power costs, reduces clutter
Select computer from keyboard command or front panel
Simple to use keystrokes switch computers for fast and easy control
Front panel has reset switch, status and power LEDs, select LEDs and select switch
Uses computer’s power — no external power required
Monitor, keyboard, and mouse plug directly into unit
Supports all brands of wheel mice
Available in two models - computers use DB25 connectors or PC connectors
Scan mode automatically sequences through CPUs at adjustable rate
Non-volatile memory stores configuration settings
Heavy-duty steel, fully shielded chassis
Comes with a one-year warranty and unlimited technical support
Made in USA
KEYBOARD AND MOUSE
n
n
n
Full emulation of keyboard and mouse, computers can be booted at any time
Computers can be PS/2 mouse or serial mouse
Keyboard Num Lock, Caps Lock, and Scroll Lock states automatically saved and
restored when switching among CPUs
Keyboard mode automatically detected
n
FRONT PANEL
n
n
n
n
n
Switch to any computer from front panel with select switch
Select LEDs show which computer is selected
Power LEDs show which computers are powered on
Status LED flashes to show keyboard and mouse activity
Reset switch reinitializes all devices
VIDEO
n
Video resolution supports up to 1600 x 1280 non-interlaced video
Uses amplifiers for crystal clear video and increased distance
n
VIStA MINI INSTALLATION AND OPERATION MANUAL
1
GETTING STARTED
To acquaint you with your Vista Mini unit, this manual first describes Vista Mini’s
front and rear panels. Then follow the installation on page 6, which is simply a
description of how to plug in the connectors.
Package contents
Your Vista Mini package includes the Vista Mini unit, your warranty registration
card, and this manual.
Vista Mini models
This manual describes two different models of Vista Mini, see Table 1 below.
The features and commands are the same, the only difference is the connector
type for the computers. Please disregard the diagrams and text that do not ap-
ply to your model. The models available are:
Table 1. Vista Mini models
Model
Computers
2 PCs
Computer connector
DB25 female
KVT-2U
KVT-2PC
2 PCs
PC (HD15F, MD6F, MD6F, 3.5mm)
Locating the unit
The Vista Mini unit is best located as close to the CPUs as possible. This will re-
duce the length of the CPU cables and provide a more cost-effective and neater
installation. While usage of the Vista Mini is trouble-free and transparent and
need not be in an accessible location, you may wish to access the front panel to
observe the LEDs, switch to a computer, or reset the unit.
Cable requirements
Vista Mini connects to each computer with various cables, depending on which
model and computer type, see the next page for the different cable types. You
plug the keyboard, monitor, mouse, and speakers directly into Vista Mini. The
cables are most commonly purchased with Vista Mini and will provide quick
and trouble-free operation.
2
VIStA MINI INSTALLATION AND OPERATION MANUAL
Most installations use cable no longer than 20 feet in length. Cable length will af-
fect the quality of the video, depending upon which resolution you will be using.
You can improve the video resolution and distance by ordering coax cables,
see Appendix C for the part number of the cable.
Cables for use with models that have DB25 connectors
To Two View
To Two View
To PC with mini-din-6
PS/2 mouse port
To PC with din-5
keyboard port
To PC with DB9 male
serial port
To PC with mini-din-6
PS/2 mouse port
To VGA video card
To VGA video card
Cable to PC computer
with PS/2 keyboard
and PS/2 mouse
Cable to PC computer
with AT keyboard
and serial mouse
CAB-VX0606Cxx (Standard)
CAB-CX0606Cxx (Coax)
CAB-VX0509Cxx (Standard)
CAB-CX0509Xxx (Coax)
Cables for use with models that have PC connectors
To PC with mini-din-6
keyboard port
To
Two View
Cable to PC with PS/2 keyboard CAB-MD6MMxx
To PC with mini-din-6
PS/2 mouse port
To
Two View
Cable to PC with PS/2 mouse CAB-MD6MMxx
Cable to PC with AT keyboard CAB-MD6MMxx
Adapter from mini-din-6 to din-5 ACC-KVM6F9F
To PC with din-5
keyboard port
To
Two View
To PC with DB9
male serial port
To
Two View
Cable to PC with serial mouse CAB-MD6MMxx
Adapter from mini-din-6 to DB9 ACC-MD6FD5M
To VGA
video card
To
Two View
Cable to PC with VGA
CAB-HD15MMxx (standard)
CAB-C1VMMxx (coax)
VIStA MINI INSTALLATION AND OPERATION MANUAL
3
VIStA MINI HARDWARE
The front panel
The Vista Mini front panel features five LEDs and two switches. To familiarize
yourself with Vista Mini’s controls and indicators, review the illustration and de-
scriptions given below.
THIS SIDE CONNECTS
TO KEYBOARD, MOUSE,
MONITOR, AND SPEAKERS
THIS SIDE CONNECTS
TO COMPUTER 1
TO SOUND CARD
ON COMPUTER 2
TO VIDEO CARD
ON COMPUTER 2
TO PS/2 KEYBOARD
ON COMPUTER 2
TO PS/2 MOUSE
ON COMPUTER 2
RESET
SWITCH LED
STATUS SELECT POWER SELECT
SWITCH
LEDS
LEDS
Table 2. The front panel
Resets the unit and initializes the keyboard and mouse, also
used to reset the unit to factory default settings
RESET SWITCH
STATUS LED
The yellow status LED lights as data is received from the key-
board and mouse. It is off when the keyboard and mouse are
idle.
The red LEDs Indicate which computer is currently selected and
connected to the keyboard, monitor, mouse, and speakers.
SELECT LEDS 1-2
The green LEDs show if the computers are powered on.
POWER LEDS 1-2
SELECT SWITCH
Selects the computer to connect to the keyboard, mouse, and
monitor.
4
VIStA MINI INSTALLATION AND OPERATION MANUAL
The connectors
All cables are connected at the Vista Mini’s side and rear panels. The side pan-
els are used to connect to the computers. The rear panel is to connect the key-
board, monitor, mouse, and speakers. For these you do not need an adapter
cable, since these should plug in directly.
Table 3. The rear panel
Panel Label
Connector
Description
Computers are connected at these ports us-
ing CPU adapter cables. You must have an
adapter cable for each CPU you plan to con-
nect.
1,2
DB25 female
or HD15 /
mini-din6
/mini-din 6 /
3.5 mm stereo
jack
Connect the VGA monitor directly to this
connector.
VGA MONITOR
PS/2 MOUSE
HD15 female
Connect the PS/2 mouse directly to this con-
nector.
Mini-din 6 fe-
male
Connect the keyboard directly to this con-
nector.
PS/2 KEYBOARD Mini-din 6 fe-
male
Connect the speakers, either powered or
unpowered to this jack.
SPEAKERS
3.5mm stereo
jack
VIStA MINI INSTALLATION AND OPERATION MANUAL
5
INSTALLATION
Step 1. Connecting monitor, keyboard, and mouse
1.1
Plug the monitor, keyboard, mouse, and speaker cables directly into
the rear panel of the unit.
Step 2. Connecting the computers
CPU cables connect your computers to Vista Mini. Each computer requires its
own cables, with appropriate connectors for your particular CPU. CPU cables
are available from Rose Electronics. Refer to page 3 for using the proper cable.
For Vista Mini models with DB 25 connectors:
2.1
Plug the DB25 male connector of the CPU adapter cable into one of the
numbered CPU ports on the Vista Mini side panel.
2.2
Plug the CPU adapter cable’s monitor, keyboard, and mouse connec-
tors into the CPU’s corresponding ports.
For Vista Mini models with PC connectors:
2.1
Plug the HD15 male-male cable from the video card into one of the
numbered HD15 female connectors on the Vista Mini rear panel.
2.2
Plug the mini-din-6 male-male cable from the computer keyboard port
into one of one of the numbered mini-din-6 female connectors with a
keyboard symbol on the Vista Mini rear panel. If your computer has a
din-5 keyboard port use the mini-din-6 female to din-5 male adapter.
2.3
2.4
Plug the mini-din-6 male-male cable from the computer mouse port
into one of one of the numbered mini-din-6 female connectors with a
mouse symbol on the Vista Mini rear panel. If your computer has a se-
rial port for the mouse use the mini-din-6 female to DB9 female adapter.
Warning do not substitute with a non-Rose adapter, there is a differ-
ence, damage may occur if you use a third-party adapter!!!
Plug the 3.5mm stereo cable into the stereo jack.
6
VIStA MINI INSTALLATION AND OPERATION MANUAL
WARNING: Avoid routing cable near fluorescent lights, air conditioning
compressors, or machines that may create electrical noise. For best quality
video, when exceeding 20 feet use coax cable. Appendix A, B, and E for fur-
ther cable information.
Step 3. Powering up the system
3.1
Boot up each of the connected CPUs. Vista Mini emulates all key-
board and mouse functions for automatic boot-up. You do not have
to re-boot the CPU, if it is inconvenient. In this case you may need to
issue the mode command, see page 9, to have proper keyboard
communication.
Step 4. Switching from the keyboard
Your Vista Mini is now ready for operation using its default settings. Pressing the
numbered switch on the front panel will switch to that computer. To take full ad-
vantage of the Vista Mini features, refer to the Operation section beginning on
page 8 The Operation section gives detailed information about each of the Vista
Mini commands, describing its application and giving the keyboard command
sequence. For your convenience, this information is summarized in the Key-
board command summary on page 14. To begin switching immediately from
the keyboard follow the instructions below.
4.1
Press and release your keyboard’s left Control Key (<Ctrl>), then
type in the computer number 1-2.
NOTE: Before entering any Vista Mini keyboard command, you must press
and release the left Control Key. This activates Vista Mini to look for com-
mands from the keyboard. You then have two seconds in which to start en-
tering a valid command.
NOTE: When entering numeric commands, use only the numeral keys
located at the top of your alpha-numeric keyboard. Numbers entered from
the numeric keypad to the right will not be recognized as valid commands.
VIStA MINI INSTALLATION AND OPERATION MANUAL
7
OPERATION
Vista Mini is simple to operate. Computer selection and function commands are
entered from the keyboard. You can also select computers manually from the
Vista Mini’s front panel by using switches 1-4. This section details each Vista
Mini function.
IMPORTANT OPERATION NOTE: To send Vista Mini keyboard com-
mands, you must first press and release the left Control Key (<Ctrl>).
Pressing and releasing <Ctrl> activates Vista Mini to look for commands
from the keyboard. You have two seconds between each keystroke to enter
a valid command, otherwise Vista Mini aborts the command.
NOTE: When entering numeric commands, use only the numeric keys lo-
cated at the top of your keyboard. Numbers entered from the numeric key-
pad to the right will not be recognized as valid commands.
NOTE: Vista Mini commands ignore case. All command letters are shown
capitalized for clarity only.
Keyboard computer selection
To select a computer from your keyboard, press and release your keyboard’s
left Control Key (<Ctrl>), then type in the computer number. Remember to use
the numbers located at the top of your keyboard. Do not use the numeric key-
pad.
Going to the other computer
From the keyboard you can switch to the other computer by selecting either the
Next or Previous computer. To go to the Next computer, press and release the
left Control Key <Ctrl>, then press the “+/=” (plus) key. To go to the Previous
computer, press and release <Ctrl>>, then press the “-/_” (minus) key. The
command is not case-sensitive. Use the keys at the top of your keyboard, not
those on the numeric pad.
Scan mode commands
To enable scanning from the keyboard, press and release the left Control Key
(<Ctrl>), then type “S”. Vista Mini will begin scanning sequentially from its cur-
rent computer to the next computer, then begin again. The time between
switching to the next computer is the scan time interval (see below) and is pro-
8
VIStA MINI INSTALLATION AND OPERATION MANUAL
grammable from 1-15 seconds. To stop scanning, press and release <Ctrl>,
then type “X”. Scanning is also disabled by entering a computer selection com-
mand. The power-on state of scanning can be saved in non-volatile memory. To
do this set the scan state and follow with the Keep command.
Scan time interval command
The scan time interval command sets the time, in seconds, that Vista Mini will
pause at each of the computers when scanning. The default setting is 5 sec-
onds. To set another interval, press and release the left Control Key, type “T”,
enter the new scan time interval (in seconds), and press <Enter>. Remember
to use the upper numeric keys, not the numeric keypad to the right. Follow with
the Keep command to save the setting.
Mode command
Vista Mini supports keyboard modes 1, 2, and 3. The keyboard mode is set by
commands from the CPU. Mode 2 is the most common mode used by the vast
majority of PCs. It is also the power-up state of all PC and PS/2 keyboards.
Mode 1 is used primarily by older IBM PS/2 models. Mode 3 is used by many
Unix workstations, such as SGI, HP, DEC, RS 6000, and others.
Vista Mini automatically detects each CPU’s keyboard mode upon CPU
boot-up, and thus learns which CPU uses which mode. If the CPU has already
booted and is then connected, Vista Mini cannot detect the CPU’s keyboard
mode and uses the setting stored in the Vista Mini’s non-volatile memory. The
mode command can be issued to change the keyboard mode for each com-
puter and can be saved in non-volatile memory with the Keep command.
To issue the Mode command, press and release the left Control Key, type ‘M“,
and enter the mode number ”1“, ”2“, or ”3“ followed by <Enter>. Remember to
use the alpha-numeric keys, not the numeric keypad, to enter the mode num-
ber. Follow with the Keep command. The mode is changed on your currently
selected computer. To change the mode on another computer, you must first
switch to that computer and then issue the mode command.
Typematic value command
Vista Mini can be configured to control the keyboard typematic rate and delay.
This setting is used to adjust the user preference of the way the keyboard acts
VIStA MINI INSTALLATION AND OPERATION MANUAL
9
when holding a key down to repeat the key, such as when moving a cursor
across a line. The rate is the speed at which the keys are sent in keys/second.
The delay is the wait time in milliseconds after the key is initially pressed, before
additional keystrokes are sent. To issue the command press and release the
left Control key, then type “A”, then enter the 1-3 digit decimal typematic value
followed by <Enter>. The typematic value is defined as shown below. Use the
keep command to save the value.
The typematic value to be used is determined from the following tables using the
equation: Typematic Value = Rate value + Delay Value. Pick the desired rate
in keys/sec. (32 choices) and delay in milliseconds (4 choices) from the tables
below. Add the values to the right of the desired settings. For example to use a
Rate of 16.0 keys/sec. and a 500 millisecond delay, the typematic value = 7 +
32 = 39, so to set this value, type <Ctrl> A 39 <Enter>.
Table 4. Typematic rate
Rate
Keys/sec
Rate
Keys/sec
Rate
Keys/sec
Rate
Keys/sec
Rate
Value
Rate
Value
Rate
Value
Rate
Value
30.0
26.7
24.0
21.8
20.0
18.5
17.1
16.0
0
1
2
3
4
5
6
7
15.0
13.3
12.0
10.9
10.0
9.2
8
9
7.5
6.7
6.0
5.5
5.0
4.6
4.3
4.0
16
17
18
19
20
21
22
23
3.7
3.3
3.0
2.7
2.5
2.3
2.1
2.0
24
25
26
27
28
29
30
31
10
11
12
13
14
15
8.6
8.0
Table 5. Typematic delay
Delay in Delay Delay in Delay Delay in Delay Delay in Delay
millisec. value millisec. value millisec. value millisec. value
250 0 500 32 750 64 1000 96
10
VIStA MINI INSTALLATION AND OPERATION MANUAL
PS/2 to serial mouse translation, wheel mouse
You can use some computers with PS/2 mouse interfaces and some computers
with serial interfaces. You must issue this command on each computer which is
serial. You must switch to each computer and issue the command.
To configure a computer for a serial mouse, press and release the left Control
Key, type “Q1”, and press <Enter>. Follow with the Keep command to save
the new setting in the unit’s non-volatile memory. To restore a computer which
was previously set to serial to regular PS/2 use Q0 instead of Q1.
Whether a computer uses a PS/2 wheel mouse or a regular PS/2 mouse is
learned by Vista when the computer loads its mouse driver. This will override
any previous setting. You can tell Vista to change its PS/2 communication to
regular or wheel with the Q command. You can also save it to non-volatile mem-
ory.
To configure a computer for a wheel mouse, press and release the left Control
Key, type “Q2”, and press <Enter>. Follow with the Keep command to save
the new setting in the unit’s non-volatile memory. To restore a computer which
was previously set to wheel mouse to regular PS/2 use Q0 instead of Q2.
Keep command
The Keep command saves the current state of the Vista Mini’s custom settings.
These settings are scan enable, scan interval, each CPU’s mode and keyboard
LED state, maximum computers, the keyboard typematic value, and the mouse
translation for each CPU. These settings are saved in non-volatile memory and
become the power-up settings. To enter the command, press and release the
left Control Key, then type “K”.
Null command
This command is used to re-synchronize an out-of-sync PS/2 mouse. Such a
condition can result due to transients, spurious power-up effects, or plugging
and unplugging of cables with live equipment. The command may need to be
entered once or twice, depending if the mouse is out-of-sync by one or two
bytes. Microsoft mouse driver version 9.01 or later corrects this inadequacy of
previous drivers and renders this command unnecessary. To issue the com-
mand, press and release the left Control Key, then type “N”.
VIStA MINI INSTALLATION AND OPERATION MANUAL
11
ROM Identification command
This command is used to identify the revision level of Vista Mini firmware cur-
rently installed. Before entering this command, your currently selected CPU
should be at a command prompt, word processor, or editor, so that when the
Vista Mini sends the ROM revision level that the result will be displayed. To issue
the command, press and release the left Control Key, then type “I”. Vista Mini
will send back its current firmware revision level, in the format
majorlevel.minorlevel.
Reset command
This command is used to re-boot the mouse and keyboard without removing
power from the Vista Mini. This is most useful to reset a PS/2 mouse which has
been unplugged and plugged back in. This command is also useful to enable
mouse data to be sent to a CPU which has not enabled the mouse. This may be
the case if the Vista Mini was not connected or powered off after a CPU was
booted up. To issue the command, press and release the left Control Key, then
type “R”. This command should not be issued to a CPU which has a PS/2
mouse connected, but no mouse driver is loaded, since many CPUs will crash if
you send them unexpected mouse data.
Immediately upon issuing the command, you will see the keyboard LEDs all go
on and then resume their previous state.
Reset computer mouse command
This command sends a mouse reset command to the currently selected com-
puter. Don’t confuse this command with the reset command which resets the
mouse itself. This command can be used to recover a stuck mouse on NT. To is-
sue the command, press and release the left Control Key, then type “O”.
Do not use this on older computers which can not recover the mouse by plug-
ging a mouse in directly as it will make the mouse go out of sync.
Reset to factory default
The settings that have been previously set and saved in non-volatile memory
can be returned to their factory default settings. This can be useful when the unit
is being moved to a new installation or to put the settings into a known condi-
12
VIStA MINI INSTALLATION AND OPERATION MANUAL
tion. To perform this operation, hold in the “1" switch on the front panel and
press and release the ”reset" switch. At least one CPU must be connected to the
unit, so that the unit can be powered. The status LED will flash three times to sig-
nify that the non-volatile memory has been returned to the original factory de-
fault settings listed in Appendix A.
VIStA MINI INSTALLATION AND OPERATION MANUAL
13
KEYBOARD COMMAND SUMMARY
To enter any keyboard command, first press and release the left Control Key,
represented by <Ctrl>. Then enter the command followed by any parameters
you wish to specify, for example the computer number.
Letter commands are not case sensitive, and are shown in upper case for clarity
only.
Do not use the numeric keypad to enter any commands.
All Vista Mini commands use a two second time-out between characters, to
abort the command. This is a feature that restores the keyboard to normal oper-
ation, so the keyboard is not put it into a command mode which might lock it up
from normal operation.
The <Ctrl> character is always passed through to the CPU. The command
characters and command operands, however, are absorbed by the Vista Mini
and not sent to the CPU.
Table 6. Keyboard command summary
Command
Key Sequence
Description
Connects your common keyboard, monitor,
and mouse to the selected computer.
Connect to
computer
<Ctrl> x
where x is 1, or 2
Selects the other computer.
Connect to
next com-
puter
<Ctrl> +
Selects the other computer
Connect to
previous
computer
<Ctrl> -
Turns Scan mode on, causing Vista Mini to
start scanning sequentially from the current
port through the remaining ports and begin-
ning again at Port 1.
Scan On
<Ctrl> S
Turns Scan mode off.
Note: Scan can also be stopped by entering
a port selection command.
Scan Off
<Ctrl> X
14
VIStA MINI INSTALLATION AND OPERATION MANUAL
Resets and enables mouse and keyboard,
enables PS/2 mouse on currently selected
port.
Reset com-
mand
<Ctrl> R
Used to re-synchronize PS/2 mouse which
has gotten out-of-sync.
Send null to
mouse
<Ctrl> N
Used to reset computer’s mouse
Reset com- <Ctrl> O (alpha not
puter mouse zero)
Identifies ROM version, CPU must be at
some sort of command prompt to receive
value.
Identify ROM
version
<Ctrl> I
Tells Vista Mini to save current scan state
and custom settings of commands shown
below.
Keep settings <Ctrl> K
Sets the time, in seconds, that Vista Mini will
pause at each port when scanning.
Note: Follow with Keep command.
Scan time in- <Ctrl> T xx <Enter>
terval
where xx is time in sec-
onds from
1-15 seconds
Sets Vista Mini CPU’s keyboard mode. Used
when CPU is booted before being con-
nected to Vista Mini.
Set keyboard Select port, then enter
mode
command:
<Ctrl> M x <Enter>
where x is 1, 2, or 3
Note: Follow with Keep command.
Sets power-on keyboard typematic action
which is controlled by the Vista Mini. This can
be used to adjust the key stroke rate and de-
lay to the user preferred setting. See Tables 4
and 5 for how the typematic value is deter-
mined.
Set typematic <Ctrl> A xxx <Enter>
value
where xxx is a
1–3 digit number’ from 0
to 127 indicating KB
typematic value
Note: Follow with Keep command.
Set mouse
type
Select port, then enter
command <Ctrl> Q x
<Enter>
Enable/disable PS/2 to serial mouse trans-
lation. Must be done for each computer
where translation is desired by switching to
where x is a 0 for a regu- it and issuing the command.
lar PS/2 mouse, 1 for a Also enables/disables wheel mouse com-
serial mouse, and 2 for a munication. Issue the command for each
PS/2 wheel mouse.
computer which has a wheel mouse.
Requires a PS/2 mouse.
Note: Follow with Keep command.
VIStA MINI INSTALLATION AND OPERATION MANUAL
15
TROUBLESHOOTING
1. CPU does not boot, keyboard error received
a. Cable is loose, reseat cable and hit F1 to continue or reboot com-
puter.
b. Wrong cable plugged in, keyboard and mouse cables reversed.
c. Cable is defective, try using cable from another CPU. If problem
goes away cable is defective.
d. Port on Vista Mini is defective, try using another port on Vista Mini. If
problem goes away port is defective.
e. Port on CPU is defective, try plugging in keyboard or mouse di-
rectly if problem remains CPU port is defective. If power LED not lit
when switched to computer which is power on, fuse on computer’s
motherboard may be blown.
2. Mouse driver does not load.
a. If PS/2 type mouse, CPU must be connected to Vista Mini or mouse
at boot-up time in order for mouse to be recognized by CPU. Re-
boot computer with Vista Mini powered on and cable attached.
b. If RS-232 type mouse, make sure right COM port is being used and
syntax of mouse driver is correct to search for the correct port.
c. Incompatible or old mouse driver being used, try latest driver. At
time of this publishing Microsoft 9.01 or later driver is best one
available.
d. Mouse translation set incorrectly, see page 11.
3. Can’t switch ports from keyboard
a. You must press and release the left control key before you press
the key which specifies the port number. You must also use the nu-
meric keys above the alphabetic keys, not those on the numeric
keypad.
4. Wrong or missing characters from those typed
a. The mode of the keyboard does not match that of the CPU. Issue
the mode command, usually 1 for IBM PS/2s and 2 for all others.
The default setting of the Vista Mini is mode 2. Sometimes an incor-
rect mode will confuse the CPU or keyboard and require re-booting
the CPU or resetting the keyboard by unplugging and plugging it
back in.
5. Mouse does not move
a. Vista Mini turned off after or not connected when CPU was booted
or the application using the mouse was run. Exit and re-enter appli-
cation or operating system using mouse or issue reset command.
16
VIStA MINI INSTALLATION AND OPERATION MANUAL
b. PS/2 mouse was not connected when Vista Mini powered up or has
been disconnected and reconnected. Issue the reset command.
c. Mouse translation set incorrectly, see page 11.
6. PS/2 mouse gets out of sync
a. Cabling was disturbed during mouse movement. Issue the null
command once or twice to re-sync the mouse. Get a later mouse
driver which does not exhibit this problem, such as Microsoft rev
9.01 or later.
7. Video fuzzy
a. Cable too long or wrong type. Use coax cable for high resolution.
8. Video not synchronized or wrong color
a. Cable is loose, reseat cable.
b. Wrong CPU cable used. If you have a 9515, 9517, 9518, XGA mono
or similar monitor you must use special cables or adapters.
c. Cable is defective, try using cable from another CPU if problem
goes away cable is defective.
d. Port on Vista Mini is defective, try using another port on Vista Mini. If
problem goes away port is defective.
9. Lower resolution video OK, but can’t enter high resolution mode
a. Wrong CPU cable used.
b. Driver has not been setup. Windows, OS/2, or other driver has not
been configured for this resolution. Configure the driver.
SERVICE INFORMATION
Maintenance and repair
The unit does not contain any user-serviceable parts inside. Any malfunction of
the unit should be reported to a factory-authorized repair center for service. Any
discrepancies in the operation of the unit according to this manual should be re-
ported to the Technical Support Department of Rose Electronics.
VIStA MINI INSTALLATION AND OPERATION MANUAL
17
APPENDIX A. FACTORY DEFAULT SETTINGS
Setting
Default
Scan enable
Off
Scan Time Interval
Caps/Numlock/Scroll
Keyboard Mode
Typematic Value
Mouse translation
5 seconds
Numlock On
2
43 (Rate=10.9 chars/sec, delay = 500 millisec.)
0 (PS/2 mouse input to PS/2 mouse output)
APPENDIX B. GENERAL SPECIFICATIONS
SIZE
.8" high by 3.2" wide by 4.2" deep
1 lb.
WEIGHT
ENVIRONMENT
0 to 55°C., 0% to 80% non-condensing
relative humidity
INPUT POWER
Supplied by computers
CPU CONNECTORS
KVT-2U
KVT-2PC
DB25 Female
HD15F/MD6F/MD6F/3.5 mm
jack
VIDEO CONNECTOR
PS/2 MOUSE CONNECTOR
KEYBOARD CONNECTOR
AUDIO CONNECTOR
CHASSIS
HD15 female VGA video
Mini-din 6 female
Mini-din 6 female
3.5 mm stereo jack
Fully shielded, black painted steel
18
VIStA MINI INSTALLATION AND OPERATION MANUAL
CONTROLS
Reset switch, computer select switch
INDICATORS
Status LED, computer select LEDs 1-2, computer
power LEDs 1-2
APPENDIX C. CABLES
Description
Part Number
CPU adapter cables for models with DB25 connectors
VGA–PS/2 keyboard–PS/2 mouse to DB25M
CAB-VX0606Cxx*
VGA–AT keyboard–Serial (9) mouse to DB25M
Coax VGA-PS/2 keyboard–PS/2 mouse to DB25M
Coax VGA-AT keyboard–Serial (9) mouse to DB25M
CAB-VX0509Cxx*
CAB-CX0606Cxx**
CAB-CX0509Cxx**
CPU cables for models with PC connectors
VGA male-male cable
CAB-HD15MMxx*
CAB-C1VMMxx*
CAB-MD6MMxx*
ACC-MD6FD5M
ACC-KVM6F9F
Coax VGA male-male cable
Mini-din-6 male-male cable
Mini-din-6 female to din-5 male adapter
Mini-din-6 female to DB9 female adapter
*Available in standard lengths of 1, 5, 10, and 20 feet
Replace xx with desired length.
**Available in 1, 5, 10, 20, 35, 50, 75, and 100 foot lengths.
Replace xx with desired length.
VIStA MINI INSTALLATION AND OPERATION MANUAL
19
ELECTRONICS
10707 Stancliff Road n Houston, Texas 77099
|