RocketFish TV Mount RF TVMFM03 User Guide

RF-TVMFM03_10-0726_QSG_V2_EN.eps 1 7/2/2010 1:18:59 PM  
V2  
FINAL  
FOR PRINT  
QUICK SETUP GUIDE  
1 Install the TV brackets  
2 Add the horizontal bars  
RF-TVMFM03  
Option 1: Installing for a flat mounting surface  
1 Slide the horizontal bars (C) through the wire guides on the TV brackets.  
2 Secure the bars to the TV brackets using the 9/16 in. × 8/32 in. Phillips head screws (W).  
1 Align the TV brackets (A and B) with the screw holes on the back of the TV.  
2 Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that  
align with the screw holes on the back of the TV, then insert the M4 screws (F), M5 screws (J),  
M6 screws (L or M), or M8 screws (Q) through the washers.  
Note: Intended for use on  
wood stud walls with 16 in.  
or less spacing only.  
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
Thank you for choosing the Rocketfish RF-TVMFM03.  
The RF-TVMFM03 TV mount is designed to support a  
flat-panel TV weighing up to 130 lbs. (58.9 kg).  
R
or  
Package contents  
A Right vertical TV bracket (1)  
M8 bag  
Q M8 × 16 mm screws (4)  
B Left vertical TV bracket (1)  
C
Horizontal TV bracket (2)  
D Arm assembly (1)  
Wall plate (1)  
M4 bag  
R
S
M8 × 40 mm screws (4)  
M8 × 60 mm screws (4)  
or  
E
Hex key bag  
T
3/16 in. hex key (1)  
C
M
3 Install the wall plate to a wood stud wall  
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).  
1 Locate the studs. Verify the center of the stud with an awl  
or thin nail or use an edge-to-edge stud finder.  
F
M4 × 12 mm screws (4)  
Lag bolt bag  
G M4 × 30 mm screws (4)  
U Lag bolt washer (4)  
V 5/16 in. × 2-3/4 in. lag bolt (4)  
Bracket hardware  
W 9/16 in. × 8/32 in. Phillips head screw (4)  
X 3/8 in. × 8/32 in. Phillips head screw (1)  
Cable ties  
Y
H M4/M5 washers (8)  
CM  
MY  
CY  
CMY  
K
Option 2: Installing for an obstructed mounting surface  
Note: Use additional washers (H) with M4/M5 hardware only.  
I
M4/M5 spacers (4)  
<5/8 in.  
2 Level the wall plate (E) and mark the hole locations.  
M5 bag  
16 in.  
1 Place the M4/M5 spacers (I) or M6/M8 spacers (P) and the M4/M5 washers (H) into the  
recessed screw holes on the back of the TV.  
2 Align the TV brackets (A and B) with the spacers and washers on the back of the TV.  
3 Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that  
align with the screw holes on the back of the TV, then insert the M4 screws (G), M5 screws (K),  
M6 screws (N), or M8 screws (R or S) through the washers.  
J
M5 × 12 mm screws (4)  
3 Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.  
4 Align the wall plate (E) with the pilot holes.  
5 Place the washers (U) over the holes in the wall plate (E),  
insert the lag bolts (V) through the washers, then tighten  
the lag bolts only until the washers (U) are pulled firmly  
against the wall plate.  
K M5 × 30 mm screws (4)  
M6 bag  
Y 8 in. nylon cable ties (5)  
Cap screws  
L
M6 × 12 mm screws (4)  
M M6 × 20 mm screws (4)  
N M6 × 35 mm screws (4)  
O M6/M8 washers (4)  
Z
5/32 in. hex key (1)  
AA Cap screws (2)  
4 Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
P
M6/M8 spacers (4)  
A
B
C
CAUTION: Avoid potential  
injuries or property damage!  
DO NOT over-tighten  
the lag bolts (V).  
M4 bag  
F
G
M4 × 12 mm  
M4 × 30 mm  
H
I
M4/M5  
M4/M5  
M5 bag  
E
J
K
D
M5 × 30 mm  
M5 × 12 mm  
M6 bag  
P
L
M
N
O
M6/M8  
M6 × 12 mm  
M6 × 20 mm  
M6 × 35 mm  
M6/M8  
Bracket hardware  
Wall  
M8 bag  
Q
R
S
W
X
10-1/5 in.  
7 in.  
(75 mm)  
3 in.  
M8 × 16 mm  
M8 × 40 mm  
M8 × 60 mm  
TV  
Hex key bag  
Cable ties  
Y
T
TV shifts 7 in. from the home position to  
full extension.  
3/16 in.  
Cap screws with hex key  
or  
U
V
Z
Lag bolt bag  
5/32 in.  
AA  
5/16 in. × 2-3/4 in.  
or  
Tools you will need:  
Stud finder  
Awl  
Socket wrench with  
1/2 in. socket or  
adjustable wrench  
7/32 in. wood drill bit  
Power drill  
Pencil  
Level  
Tape measure  
Phillips screwdriver  
or  
 

Razor Automobile 25143400 User Guide
Renesas Network Card M30870T EPB User Guide
ResMed Portable Generator VPAP Adapt SV User Guide
RIDGID Plumbing Product K 40 User Guide
Roberts Radio Clock Radio CR9932 User Guide
Ryobi Router RT101 User Guide
Ryobi Trimmer P2002 User Guide
Samsung All in One Printer SLM2875FD User Guide
Samsung Security Camera SCC B5203SP User Guide
Sennheiser Headphones 09969 User Guide