RocketFish Headphones RF RBWHP01 User Guide

RF-RBWHP01 Rocketboost Wireless Stereo Headphones  
same color jacks together (the white to the white and the red to the red).  
Note: If your audio source has only a 3.5 mmphonesor“line out”jack, use the supplied 3.5 mm-to-RCA adapter  
cable.  
To join the headphones to the docking station:  
Package contents  
1 Set the HUB STATUS switch on the docking station to ENABLE if this is your first Rocketboost  
product set.  
Rocketboost network notes:  
The power indicators turn green when the HUB STATUS switch is set to ENABLE.  
The power indicators turn blue when the HUB STATUS switch is set to DISABLE.  
AC power adapter  
Every Rocketboost network must contain  
one hub device, which helps devices join  
the network. The network can have only  
one hub, which you can enable using the  
hub switch on the back of all Rocketboost  
senders and sender/receivers. If this is your  
first Rocketboost product, you should make  
the docking station the hub, if you already  
have Rocketboost products, you should  
disable hub mode on the docking station.  
Connecting the AC adapter to the docking station  
Caution: To avoid risk of fire and to prevent damage, only use the AC adapter supplied with your wireless  
headphones. Make sure that the power supply outlet matches the AC adapter’s 120V before making the  
connection.  
Rechargeable  
batteries (2)  
Headphones  
2 Press and hold the CONNECT button on the docking station for more than three seconds to put it  
into joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode  
for 30 seconds.  
Docking station  
1
2
Connect the AC adapter connector to the docking station’s DC IN jack.  
Connect the AC adapter plug to an AC power outlet. The STANDBY indicator lights red steadily  
when the docking station is plugged in.  
3 Press and hold the CONNECT button on the headphone for more than three seconds so the  
docking station and headphone enter joining mode.  
The power indicator lights steadily if the joining was successful.  
The power indicator blinks slowly if the joining was not successful.  
3.5 mm-to-RCA  
adapter cable  
Caution: Plug the AC adapter into the power outlet only after all other connections are completed.  
Important: Hub devices must always have  
power for your network to operate. The hub  
device can be in standby (power-saving)  
mode, but must stay plugged in.  
RCA audio cable  
For more information, see your User Guide.  
User Guide  
Quick Setup Guide  
Charging the headphones  
Important: Before using the wireless headphones for the first time, make sure the batteries are fully charged for at  
Listening through the headphones  
least 16 hours. This will help provide a longer operating lifetime for the batteries.  
1 Set the headphone’s volume level to the minimum.  
Installing the headphone batteries  
Place the headphones onto the docking station. Make sure  
that the headphone charging contacts and the docking  
station charging pins make contact.  
2 Turn on the headphones and docking station. Make sure that your docking station and headphones  
The headphones are powered by two AA rechargeable  
are wirelesslyjoined.”  
batteries. Each earpiece houses one battery.  
The power indicators light steadily if the docking station and headphones are joined and blink  
slowly if they are not. If they are not joined, seeEstablishing Communicationabove or in the User  
Guide.  
R
L
Notes:  
The docking station charging indicator turns red to  
Headphone  
charging  
contact  
Do not install non-rechargeable batteries.  
Make sure that all batteries are installed correctly.  
indicate the headphones are charging.  
When the headphones are fully charged (which takes  
about eight to nine hours), the docking station charging  
indicator turns green.  
3 Put your headphones on your head. Adjust the angles of the left and right ear pieces until you feel  
1
2
With an earpiece cushion facing you, unlock and remove  
left and right earpiece cushions by slightly rotating them clockwise, then  
pulling them away from the headphones.  
Insert one AA rechargeable battery into each battery compartment. Make  
sure to align the + and - symbols on the batteries with the symbols in the  
battery compartments.  
comfortable.  
Docking station charging pin  
4 Turn on your audio source and begin playback.  
Notes:  
If there are multiple sources in the Rocketboost network, press the SOURCE button on the  
headphones to find the source you want to listen to. The TX indicator on the docking station (if it is a  
hub) blinks several times, indicating that the current audio source is changing.  
5 Adjust the headphone volume to your normal listening level.  
Caution: Continuous use at high volume may permanently damage your hearing.  
Note: If the system is connected to an A/V receiver with an external amplifier, turn off the amplifier to prevent  
hearing sound from the amplifier speakers.  
The batteries will last up to ten hours with continuous use  
(depending on the headphone volume level and distance from the docking station).  
The headphones can be charged even if the docking station or headphones are turned off.  
3 Replace the left and right cushions.  
Turning on the system  
1 Set the POWER switch on the left earpiece of headphones to ON.  
2 Press the POWER button on the docking station.  
Connecting the system to an audio source  
Caution: To prevent damage to your system, make sure all components are turned off before making connections.  
In a typical user installation, the docking station is  
Turning off the system  
Audio source  
connected to the audio output of a TV. Other devices  
Establishing communication  
1 Set the POWER ON/OFF switch located on the headphone’s left earpiece to OFF.  
2 Press and hold the POWER button on the docking station. The power indicator on the docking  
station goes off.  
Docking station  
back panel  
with audio outputs could be used as well.  
The headphones and docking station must be "joined" or wirelessly connected to each other so that  
audio can be sent from the docking station to the headphones.  
To connect the docking station to your audio  
source:  
Since the headphones and docking station are pre-joined at the factory, you can skip this step and go  
to the Listening through the headphones step. Follow this procedure only if you need to rejoin the  
headphone and docking station. For information on how to use this product with an existing  
Rocketboost network, see your User Guide.  
Using the supplied RCA audio cable, connect the audio  
output jacks of your audio source to the AUX INPUT jacks  
RCA cable (supplied)  
of the docking station. Make sure that you connect the  
© 2010 BBY Solutions, Inc., All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA 55423-3645  
ENGLISH 10-0801  
QUICK SETUP GUIDE  
 

QSC Audio Stereo System DSP 322UA User Guide
Raymarine Fish Finder L265 User Guide
Regency Indoor Fireplace F2100M User Guide
Regency Wraps Fire Pit U41 LP3 User Guide
Remington Electric Shaver R 800 User Guide
Samsung Home Theater System HT DB660 User Guide
Sanyo Camera Lens LNS T01Z User Guide
Sanyo Digital Camera VCC HD5400 User Guide
Senco Nail Gun 752XP User Guide
Sennheiser Headphones HD 400 User Guide