PCA7426G02
PROM Programming Adapter for M37273
User's Manual
Rev.1.00
September 1, 2003
REJ10J0243-0100Z
Contents
Chapter 1. Precautions for Safety ...........................................................................................4
1.1 Safety Symbols and Meanings ..............................................................................4
Chapter 2. Introduction...........................................................................................................6
2.1 Things to Check When Unpacking .......................................................................6
Chapter 3. Specifications ........................................................................................................7
Chapter 4. How to Write the Program ....................................................................................8
4.1 Programming Procedure........................................................................................8
4.2 Attaching the Adapter to a PROM Programmer ...................................................9
4.3 Setting the Jumper Switch.....................................................................................9
4.4 Mounting an MCU into the Adapter ...................................................................10
4.5 Precautions When Opening and Closing the IC Socket ......................................10
4.6 Precautions When Handling the Adapter ............................................................11
4.7 Setting the Programming Areas ..........................................................................11
Chapter 5. Recommended PROM Programmers..................................................................11
Chapter 6. Memory Maps .....................................................................................................12
Chapter 7. Troubleshooting ..................................................................................................14
7.1 Errors That Occur When Writing to PROM .......................................................14
7.1.1 When Newly Purchased ........................................................................14
7.1.2 Previously Written Normally ................................................................14
7.2 MCUs Do Not Function Normally......................................................................15
7.3 Other Precautions ................................................................................................15
7.3.1 About the Recommended PROM Programmers...................................15
7.3.2 About Reading Out of Device Identification Code ..............................15
7.4 How to Request for Support................................................................................16
To use the product properly
Precautions for Safety:
• Both in this User's Manual and on the product itself, several icons are used to insure
proper handling of this product and also to prevent injuries to you or other persons,
or damage to your properties.
• The icons' graphic images and meanings are given in "Chapter 1. Precautions for
Safety" (page 4). Be sure to read this chapter before using the product.
( 3 / 18 )
Chapter 1. Precautions for Safety
In both the user's manual and on the product itself, several icons are used to insure proper handling
of this product and also to prevent injuries to you or other persons, or damage to your properties.
This chapter describes the precautions which should be taken in order to use this product safely and
properly. Be sure to read this chapter before using this product.
1.1 Safety Symbols and Meanings
If the requirements shown in the "WARNING"
sentences are ignored, the equipment may
cause serious personal injury or death.
WARNING
If the requirements shown in the "CAUTION"
sentences are ignored, the equipment may
malfunction.
CAUTION
It means important information on using this
product.
IMPORTANT
In addition to the three above, the following are also used as appropriate.
means WARNING or CAUTION.
Example:
CAUTION AGAINST AN ELECTRIC SHOCK
means PROHIBITION.
Example:
DISASSEMBLY PROHIBITED
means A FORCIBLE ACTION.
Example:
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".
( 4 / 18 )
WARNING
Warnings for Use Environment:
• This equipment is to be used in an environment with a maximum ambient temperature of 35˚C. Care
should be taken that this temperature is not exceeded.
• Select the proper programming mode of the PROM programmer.
CAUTION
Caution to Be Taken for Modifying This Product:
• Do not disassemble or modify this product. Disassembling or modifying this product can cause
damage. Disassembling and modifying the product will void your warranty.
Cautions to Be Taken for Handling This Product:
• Use caution when handling this product. Be careful not to apply a mechanical shock such as falling.
• Do not directly touch the connector pins of this product.
• Be careful with the static electricity when handling this product and the MCU.
Caution for Keeping This Product:
• When not using this product for a long time:
(1) Attach the connector pins of this product to the conductive sponge.
(2) Put it into a conductive polyvinyl, and keep it in the package case shipped from the factory.
(3) Store it in the place where humidity and temperature are low and direct sunshine does not
strike.
(4) When using this product, check the waste of sponge has not adhered to the connector pins.
IMPORTANT
When Using The Product:
• Attach this product to the IC socket on the PROM programmer properly.
• Mount the MCU to the IC socket of this product properly.
• When opening and closing the IC socket of this product, be sure to keep it horizontal.
• Do not use the PROM programmer's device identification code readout function.
( 5 / 18 )
Chapter 2. Introduction
The PCA7426G02 is a PROM programming adapter for Renesas 7200 Series of 8-bit MCUs. The
adapter is a tool that can be used to write programs into an internal PROM of MCUs using a
commercially available PROM programmer.
This manual describes the specifications and the operation of the PCA7426G02.
Figure 2.1 shows the external view of the PCA7426G02 and its constituent parts.
Figure 2.1 External view of the adapter and its constituent parts
2.1 Things to Check When Unpacking
This product consists of the following parts listed in Table 2.1. When unpacking, check to see that
it contains all of the components shown in Table 2.1 below.
Table 2.1 Package components
Main unit
PCA7426G02
PCA7402E (32-pin)
This manual
Connector
User's manual
If any part is missing or there is any doubt about your product package, contact your local distributor.
( 6 / 18 )
Chapter 3. Specifications
Table 3.1 lists specifications of the PCA7426G02.
Table 3.1 Specifications of the PCA7426G02
Applicable MCUs
M37273EFSP, M37273E8SS and M37273ERSS
8 MHz
Operating clock frequency
(Supplied by the ceramic oscillator mounted on the adapter)
Power supply
IC socket
Supplied from Vcc of the PROM programmer
IC59-5406-G4 (made by Yamaichi Electronics Co., Ltd.)
Board to insert a programmable MCU
(IC socket mounted on it)
PCA7426G02
Board
configuration
Board to connect to the PROM programmer
(Standard-pitch 32-pin pin-header mounted)
PCA7402E
Note: The PCA7426G02 is designed to support 7200 Series 52-pin SDIP packages (52P4B), and it
is basically compatible with the future variations of the MCU series.
( 7 / 18 )
Chapter 4. How to Write the Program
This chapter describes procedures you need to follow when writing the program.
For details on how to operate the PROM programmer, refer to the user's manual of the PROM
programmer.
4.1 Programming Procedure
Follow these procedures (1) through (8) to write the program into the MCU.
(1) Read the program into the PROM programmer.
(2) Attach the adapter to the IC socket of the PROM programmer.
For details, see "4.2 Attaching the Adapter to a PROM Programmer" (page 9).
(3) Set the jumper switch (SW1).
For details, see "4.3 Setting Jumper Switch" (page 9).
(4) Mount the MCU into the adapter.
For details, see "4.4 Mounting an MCU into the Adapter" (page 10).
(5) Set the programming area with the PROM programmer.*1
For details, see "4.7 Setting the Programming Areas" (page 11).
(6) Check to erase the programming area.*2
Using the PROM programmer's erase check function, check whether data can be written into the
MCU's programming area.
(7) Write the program into the programming area of the MCU using the PROM programmer.*2
(8) Verify the programming area of the MCU using the PROM programmer to check whether the
program has been written into the MCU correctly.*2
Notes
*1 Be sure to set the programming area. Otherwise the mode's shift to the programming mode may
not be performed successfully. The erase check function and others may not also be performed
completely.
*2 Some PROM programmers perform the steps (6) to (8) automatically.
( 8 / 18 )
4.2 Attaching the Adapter to a PROM Programmer
As shown in Figure 4.1, attach the pin No. 1 of the PCA7402E connector (standard-pitch 32-pin pin-
header mounted) to the pin No. 1 of the IC socket of the PROM programmer.
Be careful when attaching the adapter because incorrect insertion can cause fatal
damage to the MCU.
Figure 4.1 Attaching the adapter to a PROM programmer
4.3 Setting the Jumper Switch
Set the jumper switch SW1 according to the MCU type you use. For settings, see Table 4.1 and Figure
4.2.
Table 4.1 Jumper switch settings
MCU
Internal ROM
Mode
SW1
EF
M37273EFSP
M37273E8SS
M37273ERSS
60 KB
32 KB
-
M5M27C101
M5M27C101
M5M27C101
E8
E8
Example when setting SW1 to E8
Figure 4.2 Jumper switch setting example
( 9 / 18 )
4.4 Mounting an MCU into the Adapter
(1) As shown in Figure 4.3, set the slide bar in the center of the IC socket to the shaded area on the
board.
(2) As shown in Figure 4.3, mount the MCU into the IC socket with the No. 1 pin of the MCU matched
to the No. 1 pin of the IC socket on the PCA7426G02.
Be careful when inserting the MCU because incorrect insertion can cause fatal
damage to the MCU.
Top view
Figure 4.3 Mounting an MCU
4.5 Precautions When Opening and Closing the IC Socket
When opening and closing the IC socket, hold the adapter horizontally as shown in Figure 4.4.
Otherwise the inside of the IC socket may become damaged and cause an electrical insulation failure.
Figure 4.4 Holding the adapter in a horizontal position
( 10 / 18 )
4.6 Precautions When Handling the Adapter
Do not touch the connector in the IC socket and the pins on the PROM programmer connector because
dirt may cause an electrical insulation failure.
When not using this product, attach the connector pins of this product to the conductive sponge as
it was shipped from the factory.
4.7 Setting the Programming Areas
When writing the program into the MCU, be sure to set the programming area. And also, specify its
device of the PROM programmer.
Table 4.2 Programming areas
PROM programmer
ROM area
of MCU
MCU type name
M37273EFSP
MCU area
Device
Programming area
1140016 - 13BFF16 1140016 - 13BFF16
0100016 - 0FFFF16 0100016 - 0FFFF16
0140016 - 03BFF16 0140016 - 03BFF16
0800016 - 0FFFF16 0800016 - 0FFFF16
0140016 - 03BFF16 0140016 - 03BFF16
OSDROM area
Internal ROM area
OSDROM area
Internal ROM area
OSDROM area
M5M27C101
M37273E8SS
M37273ERSS
Chapter 5. Recommended PROM Programmers
The PROM programmers listed in Table 5.1 are recommended for the adapter PCA7426G02. Using
the actual products, we have verified that these PROM programmers can be used to write programs
without problem. Nonconformity occurring by using any other PROM programmers can not be
supported. For the latest type of PROM programmers, contact the manufacturer to confirm whether
it can be used for your product.
Table 5.1 Recommended PROM programmers
Manufacturer
Type name
R4944A
R4945
Device
Programming voltage (VPP)
12.5 V
Advantest
Corporation
M5M27C101 mode
R4945A
( 11 / 18 )
Chapter 6. Memory Maps
Figures 6.1 and 6.2 show memory maps of the MCU and the PROM programmer.
0000016
0000016
Unused area
00FFF16
0100016
00FFF16
0100016
Internal ROM area
(60 KB)
Programming area
0FFFF16
1000016
0FFFF16
1000016
Unused area
113FF16
1140016
113FF16
1140016
OSD ROM area
256 types
OSD ROM area
256 types
13BFF16
13C0016
13BFF16
13C0016
Unused area
1FFFF16
1FFFF16
MCU
(M37273EFSP)
PROM programmer
(M5M27C101 mode)
Figure 6.1 Memory map (1/2)
( 12 / 18 )
0000016
0000016
Unused area
013FF16
0140016
013FF16
0140016
OSD ROM area
256 types
OSD ROM area
256 types
03BFF16
03C0016
03BFF16
03C0016
Unused area
07FFF16
0800016
07FFF16
0800016
Internal ROM area
(32 KB)
Programming area
0FFFF16
0FFFF16
1000016
Unused area
1FFFF16
MCU
(M37273E8SS)
(M37273ERSP)
PROM programmer
(M5M27C101 mode)
Note: The M37273ERSS has no internal ROM area (0800016-0FFFF16).
Figure 6.2 Memory map (2/2)
( 13 / 18 )
Chapter 7. Troubleshooting
The table below summarizes errors to be checked carefully before you determine them to be a fault.
7.1 Errors That Occur When Writing to PROM
7.1.1 When Newly Purchased
Remedy
Cause
See page
9
Is the adapter attached to the correct position of the PROM
programmer?
Programming adapter
Is the MCU attached to the correct position?
Is the area specification set correctly?
Is the correct device selected?
10
11
11
PROM programmer
Contact failure
The IC socket of the PROM programmer may be stained. The
socket needs replacing.
-
7.1.2 Previously Written Normally
Remedy
Cause
See page
9
Is the adapter attached to the correct position of the PROM
programmer?
Programming adapter
PROM programmer
Is the MCU attached to the correct position?
Is the area specification set correctly?
Is the correct device selected?
10
11
11
The IC socket of the PROM programmer may be stained. The
socket needs replacing.
-
-
Contact failure
The PROM programmer connector at which the PROM
programmer is contacted may be stained. Clean it with
alcohol, etc.
( 14 / 18 )
7.2 MCUs Do Not Function Normally
The program operates normally on the emulator, but when the MCU that has normally been written
is attached the same program does not function normally.
(1) Is the offset address specified correctly when copying data into the PROM programmer?
(2) In the emulator, NOPs are often inserted in the area where the program has not been read, therefore
the program happens to appear functioning normally even though it may have gone wild. Check
your program again.
(3) The emulator and the actual MCU may differ in characteristics. Consult the user's manual of the
emulation pod to check for differences in characteristics again.
7.3 Other Precautions
7.3.1 About the Recommended PROM Programmers
Not all PROM programmers available on the market can be checked to see if they function properly.
There are several PROM programmers that we have verified to function properly. These products are
listed as recommended PROM programmers in this user's manual. Other PROM programmers may
also be used providing that you verified them to function properly.
Note: No matter which type of PROM programmer you use, it is necessary to verify completion of
programming by executing screening, etc. that are stipulated for each MCU used.
7.3.2 About Reading Out of Device Identification Code *1
Please do not use the PROM programmer's device identification code readout function.
Using this function may break down the MCU. The device identification code is included in EPROM
to indicate the manufacturer code and device code; it is not included in the MCU.
1
*
Depending on PROM programmer manufacturers, this may be referred to by another name (e.g.
ID code).
( 15 / 18 )
7.4 How to Request for Support
After checking this manual, fill in the following information and email to your local distributor.
For prompt response, please specify the following information:
(1) Contact address
• Company name
• Department
• Responsible person
• Phone number
• Fax number
• E-mail address
(2) Product information
• Name of the programming adapter
• Serial number
• Date of purchase
• Target MCU
• Symptoms (Fails blank check/Cannot write a program/Fails verification etc.)
• Detailed symptoms
• How often does the problem occur? (2 out of 10 etc.)
• When did the problem start to occur? (Since purchase/Used to work correctly)
• Type name of the PROM programmer (Advantest R4945A etc.)
• Specified device when writing to PROM (M27C101 etc.)
• Specified programming area when writing to PROM
• Switch settings of the adapter when writing to PROM
( 16 / 18 )
PCA7426G02 User's Manual
Rev.1.00
September 1, 2003
REJ10J0243-0100Z
COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION
AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED
|