M32173T-PTC
Converter Board for In-circuit Connection (for M32173F2VFP/M32172F2VFP)
User's Manual
Keep safety first in your circuit designs!
• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more
reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property
damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive,
auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation,
Renesas Solutions Corporation or a third party.
• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any third-party's rights,
originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the
time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas Solutions Corporation without notice
due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor for the latest product information before purchasing a product listed herein. The
information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions
Corporation assume no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://
www.renesas.com).
• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure
to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology
Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or other loss resulting from the information contained herein.
• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human
life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular,
medical, aerospace, nuclear, or undersea repeater use.
• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce in whole or in part
these materials.
• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese
government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and
regulations of Japan and/or the country of destination is prohibited.
• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products contained therein.
Precautions to be taken when using this product
• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your program you have
finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing integration test, evaluation, or some
experiment else.
• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
• Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge. However, this does
not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any circumstances.
• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall under the
application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
September 1, 2003
REJ10J0269-0100Z
5. Connection Procedure
The procedure for connecting the M32173T-PTC is shown
below.
(1) Mount the NQPACK144SD.
(2) Mount the YQPACK144SD on the NQPACK144SD.
(3) Secure the four corners of the YQPACK144SD with the
YQ-GUIDE's.
(4) Set the clock select switch.
For details, refer to "6. Selecting the Clock" shown
below.
(5) Connect the probe of the emulation pod and the M32173T-
PTC via the SDI MCU control interface cable and the
SDI trace interface cable.
(6) Mount the M32173T-PTC on the YQPACK144SD.
Figure 3 Connection procedure of M32173T-PTC
6. Selecting the Clock
Mount an oscillator to X2 as
shown in the diagram printed on
the board.
With the M32173T-PTC, it is possible to select the clock
supply to the MCU by the clock select switch (SW1). Select
the clock supply as shown below.
However, when using the M32173T-PTC, the clock cannot
be supplied from the target system.
Connected to XIN pin of MCU
ConnectedtoXOUTpinofMCU
10 MHz: Supplies the clock (X1: 10 MHz) on the M32173T-
PTC board to the MCU.
R9: 1M Ω
R7: 510 Ω
C20: 27 pF
C22: 27 pF
SOCKET: Supplies the clock to the MCU from the socket
(X2) for mounting the oscillator on the M32173T-
PTC board. By mounting the oscillator to the X2
socket of the MCU, it is possible to change the
operating frequency.
Figure 4 Connection diagram of X2 socket
For more details on the connecting the X2 socket
and the MCU, see Figure 4 (right).
( 3 / 5 )
7. External Dimensions and Sample Foot Pattern of M32173T-PTC
Figure 5 External dimensions and sample foot pattern of M32173T-PTC
( 4 / 5 )
8. Precautions
CAUTION
Cautions to Be Taken for Emulator:
• For debugging, use this product in the combination with the M32170T-SDI or
M32100T-SDI-E emulator.
• When starting up emulator debugger PD32R, select the MCU file below according
to the type name and the operation mode of the MCU to be debugged.
MCU type name Single-chip and memory expansion modes
Microprocessor mode
M32172F2VFP
M32173F2VFP
M32172F2VWG_MCU.MCU
M32173F2VWG_MCU.MCU
M32172F2VWG_MPU.MCU
M32173F2VWG_MPU.MCU
• Connect the both cables for connecting the emulator, the SDI MCU control interface
cable (10-pin) and the SDI trace interface cable (20-pin).
• For the precautions for the combination of the emulator, refer to the user's manual
of the M32170T-SDI or M32100T-SDI-E.
Cautions for Differences between MCU and This Product:
• For debugging, as the M32173F2VWG (32KB internal SRAM) on the M32173T-
PTC is used, be careful about the difference of the SRAM size when using the
M32172F2VFP.
• When setting the clock select switch to the "SOCKET" side, the oscillation occurs
by itself, be careful about the difference of the resister value and the capacitor.
• The capacity load of the all lines of the MCU will increase depending on wirings and
connectors. Use the part whose timing is critical after checking it works properly.
Cautions to Be Taken for This Product:
• When connecting the YQPACK144SD, be sure to use the included YQ-GUIDE's.
• We cannot accept any request for repair.
• For purchasing the NQPACK144SD, YQPACK144SD and HQPACK144SD, contact
the following:
Daimaru Kogyo Ltd.
Tokyo Eletech Corporation
• For inquiries about the product or the contents of this manual, contact your local
distributor.
( 5 / 5 )
|