Owner’s Manual
Please read before using this equipment.
32-2001.fm Page 2 Friday, February 4, 2000 7:53 AM
ˆ Contents
Features ................................................................................................................... 3
Preparation .............................................................................................................. 4
Presetting the Controls ....................................................................................... 4
Choosing a Location ........................................................................................... 4
Making Connections ............................................................................................... 4
Speakers .................................................................................................................. 5
Speaker Phasing ................................................................................................ 5
Determining Total Speaker Impedance .............................................................. 6
Connecting Speakers ......................................................................................... 7
One Speaker ................................................................................................ 7
Two or More Speakers Without Transformers ............................................. 7
Multiple Speakers with Transformers ........................................................... 9
Controls and Operation ........................................................................................ 11
Troubleshooting .................................................................................................... 12
Care and Maintenance .......................................................................................... 13
Replacing Fuses ............................................................................................... 13
DC Cable ................................................................................................... 13
Amplifier ..................................................................................................... 13
Specifications ........................................................................................................ 14
Notes ...................................................................................................................... 15
© 2000 Tandy Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are registered trademarks used by Tandy Corporation.
2
32-2001.fm Page 3 Friday, February 4, 2000 7:53 AM
ˆ Features
Your RadioShack 20-Watt PA Amplifier
gives you 20 watts of solid power for
your PA system. Its wide frequency re-
sponse easily handles amplification of
voice and music. It operates on either
120 volts AC or 12 volts DC power so
you can use it anywhere you want to de-
liver special announcements or play mu-
sic with great sound.
Your amplifier is ETL listed to UL stan-
dards and meets all applicable FCC
standards.
WARNING
: To reduce the risk of fire
or shock hazard, do not expose this
product to rain or moisture.
CAUTION
Its features include:
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Microphone Jacks
up to two dynamic microphones.
— let you connect
Input Jacks
— let you connect auxiliary
equipment, such as a CD player, tape
deck, or receiver, for music and special
effects.
This symbol is intended to
alert you to the presence of
uninsulated dangerous volt-
age within the product’s
enclosure that might be of suf-
ficient magnitude to consti-
tute a risk of electric shock.
Do not open the product’s
case.
Individual Microphone Controls —
you separately adjust the volume of
each microphone.
let
Master Volume Control
just the overall sound level.
— lets you ad-
Auxiliary Volume Control
— lets you
adjust the volume of the connected
equipment.
This symbol is intended to
inform you that important
!
operating and maintenance
Tone Control
— lets you customize the
instructions are included in
the literature accompanying
this product.
sound to suit your personal preferences,
depending on the acoustics, speakers,
and sound source.
Five Speaker Terminals
— make
speaker connection easy.
3
32-2001.fm Page 4 Friday, February 4, 2000 7:53 AM
ˆ Preparation
To avoid sudden audio from the input
sources, be sure all audio devices are
turned off before you connect them to
the amplifier.
PRESETTING THE
CONTROLS
Warning:
A sudden high output from the
amplifier could damage your hearing or
the speakers connected to the amplifi-
er’s output.
CHOOSING A LOCATION
Choose a location with adequate venti-
lation. Do not place the amplifier on thick
carpeting or cushions (which can restrict
the air flow) or near a heat source, such
as a heat vent or radiator (which can
cause the amplifier to overheat).
To avoid accidentally overdriving a
channel or prematurely amplifying an
audio input, set all the amplifier’s front-
panel controls to their lowest settings.
ˆ Making Connections
Be sure you connect all auxiliary equipment
and speakers before connecting and turning on
power.
AUX/CD Input Jack
— connect any
avoid sound distortion, do not connect a
high-level audio input source to this jack.
high-level sound source (such as a tape
deck, CD player, or receiver). To con-
nect a stereo audio source to this jack,
use a shielded Y-adapter (not supplied;
available at your local RadioShack
store).
GROUND Screw
— connect the ground
wire (usually black or green) from your
turntable to this screw to avoid a low-fre-
quency hum. You can also use this
screw to ground any other system con-
nection.
PHONO Input Jack
— connect a turnta-
ble with a moving magnetic cartridge. To
4
32-2001.fm Page 5 Friday, February 4, 2000 7:53 AM
PHONO/AUX/CD Switch
input source. Even if you connected
auxiliary equipment to both the
— select the
cable’s barrel plug to this jack if you
want to temporarily power the amplifier
from your vehicle’s 12-volt battery. Then
connect the cable’s other end to your
vehicle’s 12-volt accessory socket (such
as a cigarette-lighter socket).
PHONO
AUX/CD
and
input jacks, you can use
only one source at a time.
Speaker Push Terminals
— press the
Cautions:
appropriate tab to open a terminal. In-
sert the end of a speaker wire into the
opening, then release the tab to close
the terminal and secure the wire (see
“Connecting Speakers” on Page 7).
• Your vehicle must have a negative-
ground electrical system. If you are
not sure it does, check with your
vehicle dealer.
AC Power Cord
simply plug this attached cord into a
standard AC outlet.
— to use AC power,
• Unplug the AC power cord before
you connect the DC power cable.
Likewise, disconnect the DC power
cable before you plug in the AC
power cord.
4A/12V (4-Amp/12-Volt DC Power)
Jack
— connect the supplied DC power
ˆ Speakers
Most speaker terminals are color-coded
or have a mark that indicates the termi-
nal’s polarity. Usually, terminals with
positive polarity are red or have a plus
symbol (+), and terminals with negative
polarity are black or have a minus sym-
bol (–). If the speaker terminals are un-
marked, follow these steps to determine
their polarity.
SPEAKER PHASING
Phasing is the direction the speaker
cone moves with reference to the polari-
ty of the connection wires. Proper phas-
ing is important when you use more than
one speaker in the same room or area.
Out-of-phase speakers can lose up to
one-half of their potential volume, and
can have a significantly decreased bass
effect.
1. Remove about 1 inch of insulation
from both ends of a short piece of
wire (not supplied; available at your
local RadioShack store). Then twist
the exposed wire to secure all its
strands.
Speakers are in phase if all the speaker
cones move in the same direction when
an equal signal is applied. Phasing is
correct if you observe the correct polari-
ty (+ to + and – to –) when connecting
the speakers.
2. Connect one end of the wire to one
of the speaker terminals.
5
32-2001.fm Page 6 Friday, February 4, 2000 7:53 AM
3. Touch the positive end of a 1.5-volt
flashlight battery to the speaker ter-
minal that does not have the wire
attached to it.
ed in series, parallel, or series/parallel
combined.
Note:
We recommend that you use
speakers that are rated the same (for
example, all 8-ohm speakers) for all se-
ries or parallel connections.
4. Touch the negative end of the bat-
tery with the lose end of the wire
attached to the other speaker termi-
nal. Note the direction of the cone
movement — inward or outward.
• Speakers are connected in series
when the first speaker’s positive ter-
minal is connected to the next
speaker’s negative terminal. Deter-
mine the total impedance of speak-
ers connected in series by adding
up the individual impedances of all
the connected speakers.
5. If the speaker cone moves outward,
the speaker terminal where you
touched the positive end of the bat-
tery is positive. Mark that terminal
with a + and mark the other terminal
with a –.
For example, if you want to connect
two 8-ohm speakers in series, add 8
(the impedance of one speaker)
plus 8 (the impedance of the other
speaker) for a total speaker imped-
ance of 16 ohms.
If the speaker cone moves inward,
the speaker terminal with the wire
attached that touched the negative
end of the battery is positive. Mark
that terminal with a + and mark the
other terminal with a –.
• Speakers are connected in parallel
when all their negative terminals are
connected together and all their
positive terminals are connected
together. For speakers rated the
same, find the total impedance of
speakers connected in parallel by
dividing the impedance of one
speaker by the number of speakers.
6. Remove the wire.
Repeat Steps 2–6 for each speaker with
unmarked terminals you plan to connect
to the amplifier.
DETERMINING TOTAL
SPEAKER IMPEDANCE
For example, if you want to connect
two 8-ohm speakers in parallel,
divide 8 (the impedance of one
speaker) by 2 (the number of speak-
ers) for a total speaker impedance
of 4 ohms.
Caution:
A total speaker impedance
that is higher than 16 ohms (Ω) or lower
than 4 ohms can damage your amplifier
or speakers. Be sure to make the proper
connections.
Before you connect speakers to the am-
plifier, you must determine the total
speaker impedance. In determining the
total speaker impedance, you must first
determine if your speakers are connect-
6
32-2001.fm Page 7 Friday, February 4, 2000 7:53 AM
• If you connect more than two speak-
ers using only series or only parallel
connections, the total impedance
might exceed the amplifier’s maxi-
mum impedance (16 ohms) or fall
below its minimum impedance (4
ohms).
You can connect one or more 4-, 8-, or
16-ohm speakers, with or without trans-
formers, between the amplifier’s output
and the speakers’ input. To ensure
equal volume from each speaker, all the
connected speakers should have the
same impedance rating.
For example, if you connect four 8-
ohm speakers:
One Speaker
Connect the speaker’s negative (–) ter-
–In series, the total impedance is 32
ohms (8 + 8 + 8 + 8 = 32). This
exceeds the maximum rating.
COM
minal to the amplifier’s
(common)
terminal. Then connect the speaker’s
positive (+) terminal to the amplifier’s
terminal that matches the speaker’s im-
pedance. For example, if you have an 8-
ohm speaker, connect the speaker’s
positive terminal to the amplifier’s 8-ohm
terminal.
–In parallel, the total impedance is 2
ohms (8 ÷ 4 = 2). This falls below
the minimum rating.
You can arrive at a proper total
impedance by combining series and
parallel connections.
CONNECTING SPEAKERS
You need speakers and wire to com-
plete the connections to your amplifier.
Use 16-gauge wire or larger. For parallel
connections or those involving more
than two speakers, you also need wire
connectors. All of these items are avail-
able at your local RadioShack store.
8
Speaker
Ω
Two or More Speakers Without
Transformers
We recommend connections without
transformers if the length of the connect-
ing wires between the amplifier and the
speakers is 50 feet or less.
Remove about 1 inch of insulation from
both ends of each wire. Then twist the
exposed wire to secure all its strands.
Connect the speaker wire to the amplifi-
er by pressing down on the appropriate
push terminal tab and inserting the end
of the twisted wire into the terminal’s
hole. Then release the tab to secure the
wire.
When making connections without
transformers, all the speakers must
have the same impedance rating to en-
sure equal volume from each speaker.
When there is more than one speaker in
a sound system, you must determine the
total impedance of the speakers before
7
32-2001.fm Page 8 Friday, February 4, 2000 7:53 AM
Speakers in Parallel
you can make the correct connection.
The total impedance of all the speakers
must match one of the amplifier’s output
1. To determine the total impedance of
speakers connected in parallel,
divide the impedance of one
speaker by the number of speakers.
4
8
16
terminals ( Ω, Ω, or Ω).
Speakers in Series
1. To determine the total impedance of
speakers connected in series, add
the impedance of all the speakers.
For example, if you want to connect
two 8-ohm speakers in parallel,
divide 8 (the impedance of one
speaker) by 2 (the number of speak-
ers) for a total speaker impedance
of 4 ohms.
For example, if you want to connect
two 8-ohm speakers in series, add 8
(the impedance of one speaker)
plus 8 (the impedance of the other
speaker) for a total speaker imped-
ance of 16 ohms.
Two 8 Speakers
Ω
2. Connect the speakers’ negative (–)
terminals together.
3. Connect the speakers’ positive (+)
terminals together.
Two 8 Speakers
Ω
4. Connect the speakers’ negative (–)
COM
terminals to the amplifier’s
minal.
ter-
2. Connect the first speaker’s positive
(+) terminal to the second speaker’s
negative (–) terminal.
5. Connect the speakers’ positive (+)
terminals to the amplifier’s terminal
that matches the total speaker
3. Connect the first speaker’s nega-
tive (–) terminal to the amplifier’s
impedance (4 , in this example).
Ω
COM
terminal.
Series and Parallel Combined
4. Connect the second speaker’s posi-
tive (+) terminal to the amplifier’s ter-
minal that matches the total speaker
If you must hook up more than two
speakers, you might have to use a com-
bination of series and parallel connec-
tions to get a total impedance that
matches one of the amplifier’s terminals.
impedance (16 , in this example).
Ω
8
32-2001.fm Page 9 Friday, February 4, 2000 7:53 AM
impedance of one pair of speakers)
by 2 (the number of speaker pairs)
for a total speaker impedance of 8
ohms.
5. Connect the negative (–) terminals
of all pairs of speakers to the ampli-
COM
fier’s
terminal.
6. Connect the positive (+) terminals of
all pairs of speakers to the ampli-
fier’s terminal that matches the total
Four 8 Speakers
Ω
If you connect four 8-ohm speakers in
series, the total impedance is 32 ohms
(8 + 8 + 8 + 8 = 32). This exceeds the
maximum rating.
speaker impedance (8 , in this
Ω
example).
Multiple Speakers with
Transformers
If you connect these speakers in paral-
lel, the total impedance is 2 ohms (8 ÷ 4
= 2). This falls below the minimum rat-
ing.
For complex multiple-speaker arrange-
ments that require many speakers and
long runs of connecting wire, we recom-
mend you use a line transformer (not
supplied), available at your local Ra-
dioShack store.
You can arrive at a proper total imped-
ance by combining series and parallel
connections.
1. Group speakers into pairs.
Note:
When running lengths of wire
longer than 50 feet, use wire that is
heavier than 16 gauge.
2. Connect each pair of speakers in
series.
There are several advantages to using
transformers.
For example, the total impedance of
each pair of 8-ohm speakers is 16
ohms (8 + 8 = 16).
• You can connect speakers with dif-
ferent impedances without causing
differences in output between the
speakers.
3. Connect the pairs of speakers in
parallel.
4. To determine the total impedance of
speakers connected in serial and
parallel combined, divide the imped-
ance of one pair of speakers by the
number of pairs.
• You can add or remove a speaker
without having to recalculate the
entire system’s impedance.
• You can reduce signal loss when
you use speaker wire over 50 feet
long.
For example, if you want to connect
four 8-ohm speakers in serial and
parallel combined, divide 16 (the
9
32-2001.fm Page 10 Friday, February 4, 2000 7:53 AM
Cautions:
• Before you connect the speakers,
be sure the total wattage of the pri-
mary taps you intend to use does
not exceed the amplifier’s maximum
20-watt output power rating.
Taps
• Avoid multiple connections to the
amplifier’s 70V and COM terminals.
Follow these steps to make the connec-
tions.
You need a separate transformer for
each speaker.
1. Connect a wire from the amplifier’s
70V
terminal to the transformer’s pri-
Line transformers have several connec-
tors called taps.
mary tap that matches your
speaker’s wattage rating.
The primary taps (on one side of the
transformer) are the inputs and are rated
in watts. The secondary taps (on the op-
posite side of the transformer) are the
outputs and are rated in ohms.
Note:
Usually, the wattage connec-
tions on the primary side of the
transformer are the same for all
speakers. If you want a particular
speaker to have a higher volume
level, use a higher wattage tap on
the primary side of its transformer.
Primary
Taps
2. Connect a wire from the amplifier’s
Secondary
Taps
COM
terminal to the COM taps on
the transformer’s primary side.
10
32-2001.fm Page 11 Friday, February 4, 2000 7:53 AM
3. Connect a wire from the speaker’s
positive (+) terminal to the trans-
4. Connect a wire from the speaker’s
negative (–) terminal to the COM tap
on the transformer’s secondary
side.
former’s
secondary
tap
that
matches the speaker’s total imped-
ance (4, 8, or 16 ohms).
ˆ Controls and Operation
MICROPHONE 1 and 2 Inputs
nect any standard dynamic micro-
phones.
— con-
the two microphones to get the proper
volume and balance.
PHONO/AUX Source Mixing Control
POWER Switch and Indicator
PHONO
— adjusts the input level of the
— press
AUX/CD
volume and balance.
the bottom half of the switch to turn on
the amplifier. The indicator lights. Press
the top half of the switch to turn off the
amplifier. The indicator goes off.
or
sound source for the best
TONE Control
— adjusts the sound
quality according to the speakers, sound
MASTER VOLUME Control
TONE
source, and room acoustics. Turn
— controls
LOW
the overall loudness level of all sources
equally. With the amplifier turned on and
the audio input source turned on (and
set to play, if needed), set this control to
toward
to adjust the sound toward
HIGH
a low-frequency tone, or toward
adjust it toward a high-frequency tone.
to
Notes:
5
its mid-range setting ( ). Adjust this con-
trol again after adjusting the source mix-
ing controls.
TONE
HIGH
produces
• Leaving
set to
a flat, unadjusted tone.
Caution:
Be careful not to raise the vol-
TONE
• If feedback occurs, turn
ume level too high. Doing so might over-
load the system.
LOW
toward
ume.
or turn down the vol-
MIC 1 and MIC 2 Source Mixing Con-
trols
— adjust the input level for each of
11
32-2001.fm Page 12 Friday, February 4, 2000 7:53 AM
ˆ Troubleshooting
If you should run into difficulties, check
the wiring of the system. Are there any
short circuits in the speaker wiring?
Have you provided adequate ventila-
tion? Did you calculate speaker imped-
ance correctly?
Be sure microphones and connecting
cables are not defective.
Be sure you are using large enough
speaker wire. You should always use
16-gauge (or larger) wire. The longer the
run of speaker wire, the heavier the
gauge should be.
If you have feedback problems, reposi-
tion your microphones and speakers, or
TONE
adjust
lower setting.
MASTER VOLUME
to a
or
If the amplifier does not work at all,
check the fuse on the rear panel. If it is
blown, replace it with one of the same
size and type (see “Replacing Fuses” on
Page 13).
If you are operating the unit from a 12-
volt DC power source, check the fuse in
the supplied cable that connects to your
vehicle’s 12-volt accessory socket. If the
fuse is blown, replace it with a 4-amp
125-volt fuse (see “Replacing Fuses” on
Page 13).
If you cannot solve the problem, contact
your local RadioShack store for assis-
tance.
12
32-2001.fm Page 13 Friday, February 4, 2000 7:53 AM
ˆ Care and Maintenance
To enjoy your amplifier for a long time:
Amplifier
• Keep the amplifier dry. If it gets wet,
wipe it dry immediately.
The power fuse protects your amplifier
from power (voltage or current) surges
when operating it from an AC power
source. If the POWER indicator does not
• Use and store the amplifier only in
normal temperature environments.
POWER
, check the
light when you press
fuse and replace it with one of the same
size and type. (A spare fuse is taped to
the back of the amplifier.)
• Handle the amplifier gently and
carefully. Don’t drop it.
• Keep the amplifier away from dust
and dirt.
Follow these steps to replace the ampli-
fier’s fuse.
• Wipe the amplifier with a damp cloth
occasionally to keep it looking new.
1. Unplug the amplifier’s power cord.
2. Using a flat-blade screwdriver, push
and turn the fuse holder’s cap coun-
terclockwise until the fuse holder
pops out.
Modifying or tampering with the amplifi-
er’s internal components can cause a
malfunction and invalidate its warranty.
If your amplifier is not performing as it
should, take it to your local RadioShack
store for assistance.
3. Remove the fuse holder and replace
the fuse.
4. Slide the fuse holder back in place
then, using a flat-blade screwdriver,
push and turn the fuse holder’s cap
fully clockwise to secure it.
REPLACING FUSES
DC Cable
The supplied cable is equipped with a
4A 125V fuse (in line) to protect your
amplifier from voltage surges and abnor-
mal conditions. If the power indicator
POWER
does not light when you press
,
check the fuse and, if necessary, re-
place it with one of the same size and
type.
To replace the fuse, unscrew the tip of
the cigarette-lighter plug. Then remove
the old fuse and insert the new fuse. Se-
cure the fuse by reattaching the plug’s
tip.
13
32-2001.fm Page 14 Friday, February 4, 2000 7:53 AM
ˆ Specifications
Output Power at 1 kHz, 10% THD ............................................................................... 20 Watts
THD at 1W, 1 kHz Low-Pass Filter
MIC1 .............................................................................................................................. 1%
MIC2 .............................................................................................................................. 1%
AUX CD ......................................................................................................................... 1%
PHONO ......................................................................................................................... 1%
Input Sensitivity at 10% THD, 1 kHz
MIC1 ........................................................................................................................ 2.5 mV
MIC2 ........................................................................................................................ 2.5 mV
AUX CD .................................................................................................................. 150 mV
PHONO ................................................................................................................... 3.5 mV
Signal-to-Noise Ratio (Input Shorted) with 30 kHz Low-Pass Filter
MIC1 .......................................................................................................................... 60 dB
MIC2 .......................................................................................................................... 60 dB
AUX CD ..................................................................................................................... 65 dB
PHONO ..................................................................................................................... 65 dB
Frequency Response at 8 ohms, 1W
MIC1 ........................................................................................................... 130 Hz–20 kHz
MIC2 ........................................................................................................... 130 Hz–20 kHz
AUX CD ...................................................................................................... 130 Hz–20 kHz
PHONO ................................................................................. 100 Hz 12 dB 10 kHz–13 dB
Hum and Noise at 8 ohms
at Master Volume Minimum ........................................................................................ 1 mV
at Master Volume Maximum ..................................................................................... 10 mV
Tone Control (High Cut at 10 kHz) .................................................................................. –15 dB
Power Requirement ........................................................................................... 120V AC 60 Hz
Dimensions (HWD) ......................................................................... 315/16 × 123/4 × 105/8 Inches
(99.5 × 324 × 270 mm)
Weight ................................................................................................................................... 9 lb
(4.08 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and
improvement without notice.
14
32-2001.fm Page 15 Friday, February 4, 2000 7:53 AM
ˆ Notes
15
32-2001.fm Page 16 Friday, February 4, 2000 7:53 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
32-2001
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
811081640B
02A00
Printed in China
|