Radio Shack Car Stereo System PLCD41MP User Guide

R
PLCD41MP  
CD/MP3PLAYER......  
WNER'S MANUAL  
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
A M / F M R E C E I V E R  
 
To prevent injury or fire,take the  
following precautions:  
To prevent damage to the machine,  
take the following precautions:  
Attaching panel  
Attach the front panel by fixing  
the left side of it into this unit as1  
showing.Then push the right side  
of panel towards into connecting  
plug as 2 showing.  
Insert the unit until it is firmly locked to the  
main unit, otherwise it may  
Be sure the unit is connected to a 12V  
DC power with a Negative Ground  
fall out of place when jolted  
The unit is only designed for use with 4  
speakers. Do not combine output for use  
with 2 speakers. Do not ground negative  
speaker leads to the chassis ground  
Do not open the top cover and do not install  
the unit in  
When extending the ignition, memory  
back up or ground cable, use diameter of  
0.75mm(AWG18) or  
more automotive grade cable to avoid wire  
deterioration or damage  
to the wire coating.  
place where it is exposed to direct sunlight  
(including the faceplate),in order to avoid high  
heat or humidity, water splash over it or dust.  
Do not touch the terminals of the units.  
Attaching panel  
To prevent short circuit, never put or leave  
any metallic object into the unit.  
If you smell or see smoke, turn off the  
power immediately and consult your dealer.  
Be careful not to drop or shock the unit  
strongly, it may break or crack because it  
contain glass parts.  
If you have difficulty in installing this unit  
in your vehicle. Please contact your dealer.  
If the unit seems not work in properly press  
the reset buttonto reset the memory of the  
unit.  
2
 
Follow this easy wiring diagram in order to enable you to install  
the new or existing RADIO and SPEAKER wring system.  
SPEAKER WIRING  
The unit is only designed for the use with 4 speakers system, it can  
only be connected with speakers rated in the load impedance range  
from 4 to 8 ohms. Load impedance less than 4 ohms could damage  
the unit.  
Be sure the unit is connected to a 12 volts battery with negative ground.  
Good ground connections eliminate most electrical noise problem and  
require tight with the metal vehicle chassis. remove plastic, paint or dust  
for good electrical contact.  
Never combine (BRIDGE) the outputs for use with 2 speakers, and  
Never ground any Negative speaker to the chassis ground.  
Subwoof  
CAR ANTENNA  
RED RCH  
CAR ANTENNA  
RED RCH  
LCH RCA line out  
RED RCH  
WHITE  
Auxin  
WHITE LCH  
RCA line out  
WHITE LCH  
Connect to control for antenna  
or remote control for amplifier.  
Orange  
Memory+  
YELLOW  
Grey  
Green  
Connect to battery or +12 volts of  
power source that is always live.  
Green  
/white  
Grey  
/white  
Black  
Red  
Ground-  
Right Front  
Left Front  
Brown  
Blue  
12V+  
Brown  
/white  
Blue  
/white  
Connect to lgnition key switch.  
Right Rear  
Left Rear  
3
 
Before installing the receiver permanently, fit it in the approximate place in your car Connect the  
equipment according to the speakers and electrical connections. When  
your system is operated properly,(preferably with the  
car engine running), follow the instructions  
for permanent installation  
of your system.  
3)Support strap  
(supplied)  
INSTALL THE UNIT  
1)Install half sleeve, can be with or  
without adapter. It will fit better  
with adapter.  
2)Bend over some tabs where possible  
2)Bend over tabs  
of half sleeve  
(supplied)  
tosecure the half sleeve inside of dash.  
3) Support strap to bestrutted under  
dash, secure this strip to avoid skipp  
ing of disc.  
1) Adapter  
(not supplied)  
Half sleeve  
(supplied)  
REMOVING THE UNIT  
Insert removal wrench into the small  
gap on the right side of the unit and pull  
the unit slightly out on the same side,  
then release the wrench. Repeat the  
same action for the left side. By now,  
you can remove the unit and unplug  
the wires connector.  
4) Two wrenches for release  
the unit (supplied)  
4
 
Volume  
POWER ON  
/OFF  
EJECT  
Increasing volume  
VOLUME  
Rotate the [VOL+]button  
PWR  
VOL  
Decreasing  
VOL  
SEL  
Rotate the [VOL-]button  
SEL  
SEEK  
SCN  
2
RPT  
3
SHF  
4
BAND CLOCK MODE  
DSP  
1
5
6
SELECT  
DSP  
CLOCK  
RELEASE  
MODE  
Eject  
ST  
LOUD  
LOC  
Out  
CH  
Press the [ ]button to eject the disc out of the unit .  
LCD display  
In  
Power  
Press the [ ]button again,  
to load the disc in.  
Turning ON the power  
Press the [PWR]button.  
EJECT  
Press to turn on the unit power,Press the button to turn off  
the unit.  
5
 
Hour  
MODE  
Press [  
Minute  
] button to set the hour.  
Selecting radio and play  
Press the [MODE]key.  
Press [ ] button to set the minute.  
Each time you press the key, it`ll switch between radio  
and CD position.  
Quit clock set mode  
It will quit clock set mode If there is no operation  
in 5 seconds.  
(If mode with AUX IN,the function is below:  
press MD(MODE)to select:  
1
If with DISC,press MD that is:  
AUX IN  
RADIO  
DISC  
AUX IN  
Dsp  
2
If without DISC,press MD that is:  
Short press this button to DSP  
AUX IN  
RADIO  
AUX IN  
Press LOUD button once, ROCK will bicker on display.  
Press LOUD button twice, POP will bicker on display.  
Press LOUD button third, CLASS will bicker on display.  
Band(Loud)  
DSP  
LOUD  
Release  
Long press the [BD/LD]button to emphasize the bass output,  
Long press it again to resume the normal listening.  
press the "  
" button to release faceplate.  
Clock  
Short press CLK can display time even power off .  
Long Press CLK for 3 seconds will enter set mode.  
6
 
SELECT  
Speaker mode  
PWR  
VOLUME  
TREBLE  
BASS  
VOL  
SEL  
SEEK  
SCN  
2
RPT  
3
SHF  
4
BAND CLOCK MODE  
DSP  
1
5
6
FADER  
BALANCE  
SHF  
DSP  
SCAN  
PLAY/PAUSE  
VOLUME  
REPEAT  
In press mode, VOL is sel function  
Treble set mode  
Volume set mode  
Press SEL button third,  
display shows TRE ,then  
rotate the volume  
level up. Rotate the volume  
treble level down.  
TRE  
5
Press SEL button once,display shows VOL  
then rotate the volume button  
to adjust volume level up.rotate  
the volume button to  
,
+
+
button to adjust treble  
-
button to adjust  
-
VOL  
adjust volume  
level down.  
SEL  
Balance set mode  
Press SEL button fourth  
display shows BAL ,then  
PRESS  
VOL 10  
rotate the volume  
to adjust right speaks level .  
Rotate the volume button  
to adjust left speaks level .  
+
button  
BAL  
4
Bass set mode  
-
Press SEL button twice,display shows BAS  
then rotate the volume button to adjust bass  
button to adjust  
,
+
level up. rotate the volume  
bass level down.  
-
Fader set mode  
Press SEL button fifth,display shows FAD ,then  
rotate the volume button to adjust rear speaks  
+
BAS -6  
level. Rotate the volume  
speaks level.  
-
buttonto adjust front  
FAD -3  
7
 
Play/pause  
Shf  
Pause  
Press [SHF]button  
If with DISC in unit,Press the [  
]to pause music.  
Press [SHUF] button to play all the track in random order.  
SHF and playing song number will appear on the LCD.  
Press [SHUF]again will stop random playing.  
Play  
Press the [  
DISC playing.  
]button again ,then come back to  
Scan  
Press [SCN]button  
Press this button once for TRACK INTRODUCTION.  
The first 10 seconds of each track on the disc will play. And the  
track number shows on LCD.  
To select a desired song, press [SCN]button while it is playing.  
Repeat  
Press [RPT]button  
REPEAT  
Press [REPEAT] button to repeat the track continuously.  
RPT and the playing song number will appear on the LCD.  
Press [REPEAT] again will be back to normal playing.  
8
 
Tuner  
In radio mode:  
PWR  
manual tuning:  
VOL  
SEEK-  
short press  
Short press  
button it can select higher frequency station.  
can select lower frequency station.  
SEL  
SEEK  
SEEK+  
SCN  
2
RPT  
3
SHF  
4
BAND CLOCK MODE  
DSP  
1
5
6
Auto loading tuning:  
the long press  
button it can automatically select higher  
PRESET MEMORY 1-6  
BAND  
frequency station. And the long press  
select lower frequency station.  
it can automatically  
Band  
Selecting band  
Preset memory  
Press BAND button to select among three FM or two AM bands.  
(FM1-FM2-FM3-AM)  
Manual Preset Station  
Please keep pressing any of the No.1-6 button to store when you  
hear the favorite broadcasting station.  
FM1  
AM  
FM2  
FM3  
Automatic Preset Station  
In any band play, keep pressing AS/PS on the remote control into  
automatic storage. And 6 powerful stations in this band will be stored  
into NO.1-6 respectively.  
There are 6 bands for selection:FM1,FM2,FM3,AM.Make selection  
by pressing BAND Button.  
If with DISC in unit, press [MODE] switch to radio MODE first.  
Selecting and pressing the buttons stored,you can play the station  
you want then.  
9
 
Loading and replacing the battery  
MODE  
MUTE  
Use one lithium battery(CR2025)  
insert the batteries with the +and - poles aligned properly.  
Following the illustration inside the case.  
PWR  
MODE  
BAND  
POWER  
SCAN  
MUTE  
BAND/LOUD  
REPEAT  
STU7  
ENTER  
-,_,+,0  
LOUD  
AS/PS  
1
2
3
PAUSE  
AS/PS  
ABC  
DEF  
GHI  
ID3  
PAUSE  
RPT  
SCAN  
4
5
6
LOC  
LOCAL  
MONO  
SHUF  
DSP  
JKL  
MNO  
PQR  
SHF  
DISC DN  
DISC UP  
+
DSP  
RO/SN  
MONO  
CHAR.SEL  
VOL+/CHAR.SEL  
SEL  
SHIFT  
VWX8  
YZ9  
Pull out  
SPACE  
SELECT  
CLK  
CHAR.SEL  
Store unused batteries out of the reach of children. Contact a  
doctor immediately if the battery is accidentally swallowed.  
Do not set the remote on hot places such as above the dashboard.  
_,-,+,0,PWR  
Mode select  
LOC  
MUTE  
Basic operation  
DSP  
S,T,U, ,MODE  
Enter,BAND  
Char.sel(A,B~8,9,0),+/-  
RADIO.SCAN  
MONO  
Turning ON the power  
A,B,C,1,PAUSE  
D,E,F,2,SCAN  
Press the [PWR]button.  
G,H,I,3,REPEAT  
J,K,L,4,SHUF  
Y,Z, ,space,  
V,W,X,  
Press to turn on the unit power,Press the button to turn off  
the unit.  
M.N,O,5,DISC DN  
P,Q,R,6,DISC UP  
Char.shift,SEL  
CLK  
10  
 
External view  
........ Number of items  
External view  
........ Number of items  
ID3  
MUTE  
MODE  
BAND  
LOUD  
AS/PS  
Press ID3 on remote or Panel enter ID3 selection.  
one press ID3 enter ID3 file selection mode, F will be indicated on  
LCD.  
P
AUSE  
SCAN  
RPT  
LOC  
SHF  
DSP  
DISC DN  
DISC UP  
RO/SN  
MONO  
............1  
............1  
............1  
1
2
5
6
7
SEL  
CLK  
To read in your desired song name by pressing remote ABC  
BAND  
-
buttons,  
YZ9  
ENTER  
then press confirmed the song playing.  
EXAMPLE: to read in " I LOVE YOU"  
In the read in mode: press  
............1  
............1  
............2  
YZ9  
button three times read I, press turn  
GHI  
to next word,press  
O and so on...  
Two press ID3 enter ID3 directory mode,D will be indicated on LCD.  
three times read L,press three times read  
MNO  
JKL  
BAND  
ENTER  
select desired directory,then press confirmed playing.  
Press  
/
YZ9  
VWX8  
3
4
............1  
In read in song name mode, press  
press  
YZ9  
clear wrong written words.  
SPACE  
turn to next word.  
ID3 only value as MP3 disc in.  
The use of any accessories except of those provided  
might result in damage to the unit .make sure only to  
use the accessories shipped with the unit ,as shown  
above.  
Other function  
Please refer to panel.  
Remote operation the same  
of mainframe.  
11  
 
Specifications subject to change without notice.  
CD PLAYER  
GENERAL  
Signal/Noise radio......................................................70dB  
Frequency response..............................20Hz-20KHz(+3dB)  
Channel separation..................................................>45dB  
Dual D/A converter.......................................................16Bit  
Operating power.....................................12 Volts DC,negative  
ground  
%10THD output wiring.........................Designed for using four  
speakers only front and rear  
channels cannot be combined  
in use with 2speakers.  
FM Tuner  
Load impedance..................................compatible 4 to 8 ohm  
speakers  
Tuning range............................................USA:87.5-108MHz  
(100KHz step)  
Fuses........................................................1amp and 10 amp  
Dimensions...........................................178mm(L)x50mm(W)  
x150mm(H)  
EUROPE:87.5-108.0MHz  
(50KHz step)  
FM usable sensitivity(S/N=30dB)..............................<12dB  
Stereo separation.....................................................>45dB  
Weight......................................................................2.5Kgs  
AM Tuner  
Tuning range...........................................USA:520-1620KHz  
(10KHz step)  
EUROPE:522-1620KHz  
(9KHz step)  
AM sensitivity..............................................................28dB  
12  
 
What might seem to be a malfunction in your unit may  
just be the result of slight misoperation or miswiring.  
Before calling service, first check the following table  
for possible problems.  
?No/Poor sound on one or more speakers  
Speakers or speaker wiring or volume, Balance and  
Fader setting  
Check the speaker wiring and test the speakers all in good condition  
check the setting of volume, Balance and Fader controls.  
?The power does not turn ON.  
The fuse has blown.  
Install half sleeve, can be with or  
?CD sound skips  
Installation the unit angle is greater than 45 ,or  
mounting is not fixed and the back strap is not secure.  
?NO Sound.  
The cable connect incorrectness.  
Adjust the unit with mounting angle less than 45 and make sure the  
unit is mounted securely and tighten with the back strap(supplied)  
Exactitude connect of the cable.  
?Noise on Radiopoor recepiton  
?Unit completely inoperative, no Light and Sound  
Antenna and Antenna Cable.  
Incorrect wire connection, Power RED/YELLOW or  
Ground wire or Blown fuse  
Check antenna and antenna cable, the antenna base must be  
grounded and connected with good condition, repace  
antenna or antenna cable if needed.  
Check the Red wire to +12 Volts with key lgnition witch, yellow wire to  
+12 Volts battery and black wire to ground. Check Fuse with red/yellow  
wire, or check the fuse block on your car.  
?Noise on both Radio and CD  
Poor ground,dirty or corroded at the car Battery posts  
Check the black wire for proper grounding clean and tighten ground  
connection.  
13  
 
A M / F M R E C E I V E R  
W I T H E S P F O R C D 4 0 S , M P 3 7 0 - 1 2 0 S  
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
 

Rackmount Solutions Switch RKP21x 208KVM User Guide
Radio Shack CD Player CD 3316 User Guide
Remington Hair Dryer ID 2002 User Guide
Rotel Stereo Amplifier RHBO5 User Guide
Rowenta Electric Shaver 030013 4 03 SH315 345 User Guide
Sansui Flat Panel Television SLED3900 User Guide
Seagate Computer Drive ST1181677FC User Guide
Seagate Personal Computer 100743772 User Guide
Sears Electric Heater 58335601 User Guide
Sears Refrigerator 53471 User Guide