Radio Shack Baby Toy SC 100 User Guide

WARNING: Always check your wiring before  
turning on circuit. Never leave circuit  
unattended while the batteries are installed.  
Never connect additional batteries or any other  
power sources to your circuits.  
WARNING: SHOCK HAZARD -  
Never connect Snap Circuits  
to the electrical outlets in your  
home in any way!  
a
a
Space Battle  
Model SCP-05  
Project #2  
Space Battle  
Remove the photoresistor (RP) from the circuit shown. Activate the  
circuit by pressing the press switch (S2). The space war sounds play as  
long as the switch is pressed. Release and press the switch several  
times to hear all the different sounds.  
Project #3  
Touch Space Battle  
Remove the photoresistor (RP) and press switch (S2) from the circuit  
shown, and turn on the slide switch (S1). Wet two of your fingers and  
touch them across where the photoresistor was connected. You hear  
space battle sounds when your fingers complete the circuit.  
Project #4  
Photo Space Battle  
Use the same circuit as for project #1 but replace the press switch (S2)  
with the photoresistor (RP) and turn on the slide switch (S1).  
The photoresistor contains material that changes its resistance when it  
is exposed to light, as it gets more light, the resistance of the  
photoresistor decreases. Parts like this are used in a number of ways  
that affect our lives. For example, you may have streetlights in your  
neighborhood that turn on when it starts getting dark and turn off when  
it is light.  
Project  
#1  
Doub  
e
SSpace Battle  
The Snap Circuits Kit uses electronic blocks that snap onto a clear plastic base grid to build different  
circuits. These blocks have different colors and numbers on them so that you can easily identify them.  
Build the circuit shown by placing all the parts with a black 1 next to them on the clear plastic base grid  
first. Then, assemble parts marked with a 2. Install two (2) “AA” batteries (not included) into the battery  
holder (B1).  
Find a piece of white paper that has a lot of large black or dark areas on  
it, and slowly slide it over the photoresistor (RP). You should hear the  
sound pattern constantly changing, as the white and dark areas of the  
paper control the light to the photosensitive resistance. You can also try  
the pattern below or something similar to it:  
Turn on the slide switch (S1). Activate the circuit by pressing the press switch (S2) or waving your hand  
just above the photoresistor (RP), do both several times and in combination. You will hear an exciting  
range of sounds, as if a space battle is raging!  
The space war IC is a super-miniaturized electronic circuit that can play a variety of cool sounds stored  
in it by using just a few extra components. In movie studios, technicians are paid to insert sounds like  
these at the precise instant a gun is fired. Try making your sound occur at the same time an object hits  
the floor. It is not as easy as it sounds.  
®
If you have any problems, contact Elenco  
Copyright © 2005 Elenco® Electronics, Inc. All Rights Reserved. • 150 Carpenter Ave. • Wheeling, IL 60090  
(800) 533-2441 Fax: (847) 520-0085 • e-mail: [email protected] • Web site: www.elenco.com or www.snapcircuits.net  
 
753144  

Quantum Data Portable Generator 802R PCI User Guide
RAD Data comm Network Card ASMi 31 User Guide
Radio Shack Scanner PRO 528 User Guide
Roland Musical Instrument HPi 7 User Guide
Ryobi Sander P430 User Guide
Samsung Home Theater System AH68 01835K User Guide
Samsung Home Theater System AH68 01852B User Guide
Samsung Security Camera SSC 17TQ User Guide
Samsung Washer SW52ASP User Guide
Savin All in One Printer 9925DP User Guide