Cat. No. 43-759
A
OWNER’S MANUAL
Please read before using this equipment.
TAD-759
Digital Answering System
with 13-Memory Telephone
This TAD has been tested and certified
to comply with applicable UL and FCC
standards.
Telephone Features
Priority Memory Dialing — lets you
store three priority memory numbers
and call them with the touch of a button.
10 Indirect Memory Locations — let
you quickly dial frequently-called num-
bers.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
Tone/Pulse Dialing — lets you use ei-
ther type of service, and you can easily
switch from pulse to tone dialing for
long-distance, bank-by-phone, or other
special services.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Redial — lets you quickly redial the last
number dialed.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
Flash — sends an electronic switch-
hook signal for use with special phone
services such as Call Waiting.
Privacy — prevents the person on the
phone from hearing your conversation
with someone in the room.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
Ringer Volume Switch — lets you ad-
just the ringer’s sound level.
!
Handset Volume Control — lets you
adjust the volume you hear during a call.
Hearing-Aid Compatibility — lets you
use the phone with any hearing aid that
has a T (telephone) switch.
3
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
Your TAD complies with Part 68 of
FCC
. You must, upon request, provide
Rules
We have designed your TAD-759 to
conform to federal regulations, and you
can connect it to most telephone lines.
However, each device you connect to
the phone line draws power from the
line. This power draw is the device’s
the FCC registration number and the
REN to your telephone company. Both
numbers are marked on the bottom of
the TAD.
Note: You must not connect the TAD to:
• coin-operated systems
, or REN. The
ringer equivalence number
REN is on the bottom of the TAD.
• party-line systems
If you use more than one telephone or
other device on the line, add up all of the
RENs. If the total is more than five, your
telephones might not ring. In rural areas,
a total REN of three might impair ringer
operation. If ringer operation is impaired,
remove a device from the line.
• electronic key telephone systems
Your TAD complies with the limits for a
Class B digital device as specified in
Part 15 of
. These limits pro-
FCC Rules
vide reasonable protection against ra-
dio and TV interference in a residential
area. However, your TAD might cause
TV or radio interference even when it is
operating properly. To eliminate interfer-
ence, you can try one or more of the fol-
lowing corrective measures:
• Reorient or relocate the receiving
antenna of the radio or TV antenna.
• Increase the distance between the
TAD and the radio or TV.
• Use outlets on different electrical cir-
cuits for the TAD and the radio or TV.
Consult your local RadioShack store if
the problem still exists.
4
CONTENTS
Preparation .......................................................................................................... 6
Installing a Backup Battery ............................................................................. 6
Mounting the TAD ........................................................................................... 6
On a Desk Top .......................................................................................... 7
On a Wall Plate or Wall ............................................................................ 7
Setting the Dialing Mode ................................................................................. 8
Setting the Day and Time ............................................................................... 9
Setting the Number of Rings ......................................................................... 10
Telephone Operation ......................................................................................... 11
Setting the Ringer’s Volume .......................................................................... 11
Using Redial ................................................................................................. 11
Adjusting the Handset’s Volume ................................................................... 11
Using Flash ................................................................................................... 11
Using Privacy ................................................................................................ 12
Using Tone Services on a Pulse Line ........................................................... 12
Memory Dialing ............................................................................................. 12
Storing Numbers in Memory .................................................................. 12
Dialing a Stored Number ........................................................................ 13
Testing Stored Emergency Numbers ...................................................... 13
Chain-Dialing Special Service Numbers ................................................ 13
TAD Operation ................................................................................................... 14
Recording the Outgoing Message ................................................................ 14
Adjusting the TAD’s Volume .......................................................................... 14
Setting the TAD to Answer Calls ................................................................... 14
Recording Incoming Messages .................................................................... 15
Screening Calls ............................................................................................. 15
Playing Messages ......................................................................................... 15
Deleting Messages ....................................................................................... 16
Recording a Memo ....................................................................................... 17
Changing the Remote Operation Security Code .......................................... 17
Remote Operation ............................................................................................. 18
Using Toll-Saver ............................................................................................ 18
Using Remote Commands ............................................................................ 18
Remote Commands ............................................................................... 19
Troubleshooting ................................................................................................ 20
Care and Maintenance ...................................................................................... 21
The FCC Wants You to Know ....................................................................... 22
Lightning ....................................................................................................... 22
5
PREPARATION
Replace the battery when
appears
Lo
INSTALLING A BACKUP
BATTERY
on the message counter. Be sure the
AC adapter’s cord is plugged in while
you replace the battery, so you do not
lose any stored information.
The TAD requires AC power to operate.
However, if AC power fails or you un-
plug the TAD-759, a 9-volt battery (not
supplied) saves the messages, time and
day settings, memory numbers, and the
remote operation security code. We rec-
ommend a RadioShack alkaline battery.
Cautions:
• Always remove an old or weak bat-
tery. Batteries can leak chemicals
that can destroy electronic parts.
• Dispose of old batteries promptly
and properly. Do not burn or bury
them.
Note: The telephone operates normally
during a power failure; however, the
TAD cannot answer and record incom-
ing calls without AC power.
MOUNTING THE TAD
Follow these steps to install the battery.
You can place the TAD-759 on a desk,
mount it on a standard wall plate, or
mount it directly on a wall. Select a loca-
tion that is near both a modular tele-
phone line jack and an AC outlet.
Warning: If the TAD’s modular line cord
is connected to a phone line jack, dis-
connect it before installing a battery.
This reduces the risk of electric shock.
Caution: Use only a fresh battery of the
required size and recommended type.
Notes:
• Your TAD-759 connects directly to a
modular telephone line jack. If your
telephone wiring does not have a
modular jack, you can update it
yourself using jacks and adapters
available at your local RadioShack
store, or have the telephone com-
pany update it for you.
1. Use a flat-blade screwdriver to
unlatch the battery compartment
cover (as shown), then open the
cover.
• The USOC number of the jack to be
installed is RJ11C (or RJ11W for a
wall plate jack).
2. Snap the battery’s terminals to the
connector inside the compartment.
Caution: The supplied AC adapter was
designed specifically for your TAD-759.
Use only the supplied adapter.
3. Close the cover and press down on
the latch to close it.
6
6. Plug the adapter into a standard AC
outlet.
On a Desk Top
1. Plug one end of the supplied long
modular cord into the TEL. LINE jack
on the back of the base.
_ _
When you first connect power,
flashes on the message counter as
the TAD runs a self-test. The TAD
TEL. LINE Jack
beeps and
appears when the
00
test is complete.
On a Wall Plate or Wall
Note: To mount the base directly on the
wall, you need two screws (not supplied)
with heads that fit into the keyhole slots
on the bottom of the base. Drill two holes
315/16 inches (100 mm) apart. Then thread a
screw into each hole, letting the heads ex-
tend about 3/16 inch (5 mm) from the wall.
2. Plug the cord’s other end into a
modular phone line jack.
3. Plug one end of the supplied coiled
handset cord into the jack at the left
side of the base. Plug the other end
into the handset’s jack.
1. Snap the supplied mounting bracket
into the slots on the bottom of the
TAD as shown.
4. Place the handset on the base.
Note: Be sure the keyhole slots on
the bracket and the TAD are aligned
in the same direction.
5. Insert the supplied AC adapter’s
barrel plug into the AC 9V jack on
the back of the base.
2. Plug one end of the supplied short
modular line cord into the TEL. LINE
jack on the back of the TAD.
AC 9V Jack
TEL. LINE Jack
7
3. Insert the supplied AC adapter’s
barrel plug into the AC 9V jack on the
back of the base.
AC 9V Jack
4.
To mount the phone on a wall plate,
plug the other end of the modular
cord into the wall plate jack. Then,
with the power cord hanging over
the bracket, align the TAD’s keyhole
slots with the wall plate studs and
slide the TAD downward to secure it.
5. Slide the handset clip out of its
retaining slot, rotate it 180 , then
°
slide it back into its slot.
6. Plug one end of the supplied coiled
handset cord into the jack at the left
side of the base. Plug the other end
into the handset’s jack.
7. Place the handset on the base.
8. Plug the adapter into a standard AC
outlet.
_ _
When you first connect power,
To mount the phone directly on a
flashes on the message counter as
the TAD runs a self-test. The TAD
with the power cord and the
wall,
modular cord hanging over the
bracket, align the TAD’s keyhole
slots with the screws and slide the
TAD downward to secure it.
beeps and
appears when the
00
test is complete.
SETTING THE DIALING
MODE
Set PULSE/TONE for the type of service
you have. If you are not sure which type
you have, follow these steps.
8
1. Set PULSE/TONE on the back of the
1. Hold down SET until the TAD beeps.
TAD to TONE.
The TAD announces, “Sunday,” and
appears on the display.
01
2. Lift the handset and listen for a dial
tone.
Note: If necessary, adjust VOLUME
on the right side of the TAD to the
desired listening level.
3. Press any number except 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not dial the access code
either.
If the dial tone stops, you have touch-
tone service. Leave PULSE/TONE set to
TONE.
2. To change the day, repeatedly press
SKIP to move backward or REPEAT
to move forward until the TAD
announces the desired day.
If the dial tone continues, you have
pulse service. Set PULSE/TONE to
PULSE.
SETTING THE DAY AND
TIME
3. Press STOP. The TAD shows the cur-
rently set hour and announces “AM”
or “PM.”
The TAD-759 records the day and time
each memo and message is recorded.
Follow these steps to set the day and
time.
Note: If you do not complete each step
within 8 seconds, the TAD sounds three
beeps and exits. Start again at Step 1.
4. To change the hour, repeatedly
press SKIP or REPEAT.
9
5. Press STOP. The TAD shows the cur-
rently set minute.
6. To change the minutes, repeatedly
press SKIP or REPEAT.
7. Press STOP. The TAD announces
the day and time.
To check the current day and time at
any time, press SET.
SETTING THE NUMBER
OF RINGS
Set the ring select switch on the back of
the TAD to 4, 7, or TS to set how long
the TAD waits before it answers a call (4
rings, 7 rings, or toll-saver).
If you plan to check your messages by
long distance, set the ring select switch
to TS (see “Using Toll-Saver” on
Page 18).
10
TELEPHONE OPERATION
Place and answer phone calls with the
TAD-759 as you would with any stan-
dard phone.
ADJUSTING THE
HANDSET’S VOLUME
The TAD-759 has three volume levels.
To adjust the volume you hear through
the handset, slide HANDSET VOLUME HI/
MED/LO to the desired volume during a
call.
SETTING THE RINGER’S
VOLUME
To change the ringer’s volume, set the
ringer volume switch on the back of the
base to LO for a normal ringer volume,
or HI for a louder ring.
USING FLASH
Use FLASH to perform the switchhook
operation for special services, such as
Call Waiting.
If you do not want the ringer to sound,
set the ringer volume switch to OFF. You
can still make calls with the ringer off,
and you can answer calls if you hear an-
other phone on the same line ring.
USING REDIAL
To quickly dial the last number dialed, lift
the handset and press REDIAL.
For example, if you have Call Waiting,
press FLASH to take an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
Note: If you do not have special phone
services, pressing FLASH might discon-
nect the current call.
Note: The redial memory stores 31 tone
digits or 32 pulse digits.
11
in the indirect memory locations, then
quickly call each number with a few key
presses.
USING PRIVACY
To talk to someone else in the room
without the person on the other end of
the phone line hearing you, hold down
PRIVACY. Release it to resume your
telephone conversation.
Each memory location can store up to
15 tone digits or 16 pulse digits.
Storing Numbers in Memory
Note: You will hear a dial tone during
most steps of this procedure. The phone
does not actually dial the number as you
store it, but you might also hear a busy
tone or recorded operator’s voice after a
few seconds. This is normal.
USING TONE SERVICES
ON A PULSE LINE
1. Lift the handset.
If you have pulse service, you can still
use special services that require tone
signals, such as bank-by-phone, by fol-
lowing these steps.
2. Press STORE.
1. Be sure PULSE/TONE is set to
PULSE.
3. Enter the phone number you want to
store.
2. Dial the service’s main number.
3. When the service answers, set
PULSE/TONE to TONE. Any addi-
tional numbers dialed are sent as
tone signals.
Notes: If you make a mistake, hold
down the switchhook for a few sec-
onds, then release it and start over
at Step 2.
4. When you complete the call, set
4. Select the memory location for the
number.
PULSE/TONE back to PULSE.
MEMORY DIALING
You can store emergency phone num-
bers or the phone numbers you call
most frequently in the three priority
memory locations for one-touch dialing.
You can store 10 more phone numbers
12
• For a priority memory location,
Testing Stored Emergency
Numbers
press P1, P2, or P3.
• For an indirect memory location,
press MEMORY, then enter a two-
digit memory location number
(01–10).
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you want to test
the stored number, make the test call
during the late evening or early morning
hours to avoid peak demand periods.
Remain on the line to explain the reason
for your call.
5. To keep a record of each stored
number, use a straightened paper
clip to remove the plastic cover on
the memory index card on the lower
left of the base and write the name
on the card. Use a pencil in case
you want to change it later.
Chain-Dialing Special Service
Numbers
For quick recall of numbers for special
services (such as alternate long-dis-
tance or bank-by-phone), you can store
each group of numbers in its own mem-
ory location.
When calling special services, dial the
service’s main number first. At the ap-
propriate place in the call, dial the ap-
propriate memory number for the
additional numbers you want to send
(see “Dialing a Stored Number” on
Page 13).
6. Repeat Steps 3–5 (without hanging
up) to store more numbers. Then
hang up the handset when you fin-
ish.
Dialing a Stored Number
To dial a priority memory number, lift the
handset and press P1, P2, or P3.
To dial an indirect memory number, lift
the handset and press MEMORY. Then
press the keys for the two-digit memory
location number for the number you
want to call.
13
TAD OPERATION
RECORDING THE
OUTGOING MESSAGE
ADJUSTING THE TAD’S
VOLUME
Before you can set the TAD to answer
calls, you must record an outgoing mes-
sage (OGM). This is what the caller
hears when the TAD answers a call. The
outgoing message can be up to 60 sec-
onds long.
To adjust the TAD’s volume, rotate VOL-
UME on the right side of the TAD.
Hint: Do not tell callers that you are not
home. Instead, say that you cannot
come to the phone right now.
SETTING THE TAD TO
ANSWER CALLS
Note: If memory is full (
appears)
FL
when you attempt to record an outgoing
message, the TAD announces, “Memory
is full.”
To set the TAD to answer calls, press
ANSWER. The TAD announces, “Answer
on,” and the ANSWER indicator appears
in the message counter window.
1. Hold down ANNOUNCE. The TAD
beeps, and the display begins
counting down from 60 seconds.
Note: If no outgoing message is record-
ed, the TAD says, “Answer off, no an-
nouncement.” Record an outgoing
message.
2. Speak your message in a normal
voice about 8 inches from the front
of the TAD.
3. When you finish, release AN-
NOUNCE. The TAD plays back the
outgoing message so you can check
it.
To set the TAD to not answer calls,
press ANSWER again. The TAD says
“Answer off,” and the ANSWER indica-
tor turns off.
To hear your outgoing message at any
time, press ANNOUNCE. To change your
outgoing message, repeat Steps 1–3.
14
Note: If you pick up the phone just as
the TAD answers, the TAD might not
stop playing the outgoing message. If
this happens, press STOP.
RECORDING INCOMING
MESSAGES
The maximum length for each incoming
message is 60 seconds. If a recording
reaches 55 seconds, the TAD beeps
once to notify the caller that time will be
up soon. If a recording reaches 60 sec-
onds, the TAD beeps three times, then
disconnects.
PLAYING MESSAGES
The message counter shows the total
number of messages, both old (ones
you have listened to and saved) and
new.
The TAD stops recording and resets to
answer the next call when:
If there are new messages, the mes-
sage counter flashes until all the new
messages have been played.
• the caller hangs up
• there are more than 8 seconds of
silence
To play only new messages, hold down
PLAY for about 2 seconds. If there are
no new messages stored, the TAD says,
“No new message.” If there are no mes-
sages stored, the TAD says, “No mes-
sage.”
• you pick up any phone on the same
line as the TAD
Note: To bypass the outgoing message,
tell the caller to press when the mes-
sage begins. The TAD beeps once, and
begins recording.
SCREENING CALLS
To screen calls, let the TAD answer,
then listen to the caller’s message
through the TAD’s speaker.
To play all messages, press PLAY. The
TAD announces the number of messag-
es recorded. Before playing each mes-
sage, the TAD tells you the message’s
number and the day and time the mes-
sage was recorded.
If you do not want to take the call, simply
let the TAD finish recording the caller’s
message.
If you decide to answer the call, pick up
this phone or any phone on the same
phone line as the TAD. The TAD stops
recording and resets to answer the next
call.
15
After all messages play, the TAD says,
“End of messages.”
resets to answer calls. The total number
of messages appears.
To replay a message while you are lis-
tening to it, press REPEAT. The current
message replays from the beginning.
To stop playing messages, press STOP
twice quickly. The TAD beeps and stops
playback and resets to answer calls.
To return to the previous message, hold
down REPEAT until its number appears.
To hear earlier messages, repeat the
procedure.
DELETING MESSAGES
To delete a specific message, press DE-
LETE while the message is playing. The
TAD beeps, then plays the next mes-
sage.
To skip to the next message, press
SKIP. The next message plays.
To pause a message, press STOP.
(pause) appears. Press STOP again to
resume playing messages.
To delete all messages, stop playback,
then hold down DELETE until the TAD
beeps. The TAD erases all the messag-
es you have listened to, and the number
of remaining messages appears.
PA
The TAD-759 does not delete new mes-
sages. If you have
new messages,
only
the TAD announces “New messages”
when you hold down DELETE.
Note: If you do not resume playing mes-
sages within 60 seconds, the TAD
beeps three times, stops playback, and
16
Notes:
• Be sure to set each digit within 8
RECORDING A MEMO
A memo is a message you can record at
the TAD, without having to call in on the
phone. The TAD-759 can record a
memo of up to 60 seconds long.
seconds. Otherwise, you must start
over at Step 1.
• If AC power fails and the backup
battery becomes weak, the remote
operation security code automati-
cally resets to 759.
To record a memo, hold down MEMO.
The TAD beeps, and the display begins
counting down from 60 seconds. Speak
in a normal voice about 8 inches from
the front of the TAD. When you finish,
release MEMO.
1. Hold down CODE for about 2 sec-
onds. The TAD beeps, and the first
digit of the preset code flashes on
the display.
The memo is stored with the incoming
messages. To hear the memo, simply
play back your messages.
2. Press SKIP or REPEAT to set the first
digit, then press STOP. The TAD
beeps, and the second digit appears
and flashes.
Note: If the TAD’s memory is full (
FL
and the number of messages alternately
appear on the display), you must erase
some messages before you can record
a memo.
3. Press SKIP or REPEAT to set the
second digit, then press STOP. The
TAD beeps, and the third digit
appears and flashes.
CHANGING THE REMOTE
OPERATION SECURITY
CODE
4. Press SKIP or REPEAT to set the
third digit, then press STOP. The TAD
beeps and shows the new security
code in sequence.
The TAD-759’s remote operation securi-
ty code is preset to 759. Follow these
steps to change the code.
To see the currently set code at any
time, press CODE.
17
REMOTE OPERATION
While you are away from your home or
office, you can use a touch-tone phone
or a pulse (rotary) phone with a pocket
tone dialer (available at your local Ra-
dioShack store) to enter your remote op-
eration security code and do any of the
following:
USING REMOTE
COMMANDS
Follow these steps to operate the TAD
from a touch-tone phone or a pulse (ro-
tary) phone with a pocket tone dialer.
1. Dial your phone number.
• set the TAD to answer or not answer
calls
2. When the TAD answers, enter your
remote operation security code. The
TAD beeps once to confirm that you
entered the correct code.
• listen to your messages
• record a new announcement
• delete messages
Notes:
• monitor the room where the TAD is
located
• If you do not enter each digit of
the security code within 8 sec-
onds, the TAD hangs up.
Note: You cannot remotely operate the
TAD from another phone on the same
line as your TAD-759.
• Even if the TAD is not set to
answer calls, it will answer after
about 60 seconds.
3. Enter a remote command (see
“Remote Commands” on Page 19).
USING TOLL-SAVER
4. When you finish, simply hang up.
If the ring select switch is set to TS (toll-
saver, see “Setting the Number of
Rings” on Page 10) the TAD answers af-
ter two rings if you have new messages.
If there are no new messages, the TAD
waits for four rings before it answers.
This gives you time to hang up before
the TAD answers so you can avoid un-
necessary long-distance charges.
18
After you press 4 or 5 to play messages,
you can:
Remote Commands
Press:
0
To:
Press:
6
To:
Stop playback, recording,
and room monitoring.
Delete the current mes-
sage.
1
2
3
Play the outgoing mes-
sage.
7
8
9
0
Replay the previous mes-
sage.
Record a new outgoing
message.
Replay the current mes-
sage.
Monitor the room where
the TAD is located for 30
seconds.
Skip forward to the next
message.
Stop message play.
4
5
6
Play all messages.
Play only new messages.
Delete messages. (The
TAD will not delete mes-
sages that have not been
played.)
#
Set the TAD to answer or
not answer calls.
19
TROUBLESHOOTING
We do not expect you to have any problems with your TAD-759, but if you do, the fol-
lowing suggestions might help.
Problem
Suggestion
There is no dial tone.
Check all phone line connections, including the
handset cord.
The incoming message is
incomplete.
Be sure the TAD’s memory is not full.
The caller’s message was longer than 60 seconds.
The caller was silent for more than 8 seconds.
flashes on the message The backup battery is weak. Replace the battery
Lo
counter.
(see “Installing a Backup Battery” on Page 6).
Make sure the TAD is set to answer calls.
Check all phone line connections.
TAD does not answer calls.
Make sure the AC adapter is properly connected.
TAD does not record callers’ Memory may be full (
appears). Delete some of
FL
messages.
your messages.
No messages appear on the This could be caused by a power failure. Reset the
message counter.
TAD by removing the AC adapter and the battery
from the TAD, then reconnect the adapter and rein-
stall the battery.
The TAD does not respond
to the remote operation
security code.
Make sure the phone you used to dial the TAD is a
touch-tone phone. (If it is not, you can use a
pocket tone dialer to enter the code and com-
mands.)
Make sure the remote operation security code you
entered is correct. Try entering the default code of
759. The TAD may have reset to the default code
because of a power failure.
Re-enter your security code, pressing each button
for 2 seconds.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your TAD-759 to your local RadioShack store for assistance.
20
CARE AND MAINTENANCE
Your RadioShack TAD-759 Digital Answering System is an example of superior de-
sign and craftsmanship. The following suggestions will help you care for your TAD so
you can enjoy it for years.
Keep the TAD dry. If it gets wet, wipe it dry immediately. Liquids might
contain minerals that can corrode the electronic circuits.
Use and store the TAD only in normal temperature environments. Tem-
perature extremes can shorten the life of electronic devices, damage
batteries, and distort or melt plastic parts.
Keep the TAD away from dust and dirt, which can cause premature
wear of parts.
Handle the TAD gently and carefully. Dropping it can damage circuit
boards and cases and can cause the TAD to work improperly.
Use only fresh batteries of the required size and recommended type.
Batteries can leak chemicals that damage your TAD’s electronic parts.
Wipe the TAD with a damp cloth occasionally to keep it looking new. Do
not use harsh chemicals, cleaning solvents, or strong detergents to
clean the TAD.
Modifying or tampering with the TAD’s internal components can cause a malfunction
and might invalidate its warranty and void your FCC authorization to operate it. If your
TAD is not performing as it should, take it to your local RadioShack store for assis-
tance. If the trouble is affecting the telephone lines, the phone company can ask you
to disconnect your TAD until you have resolved the problem.
21
THE FCC WANTS YOU TO
KNOW
LIGHTNING
Your TAD has built-in protection circuits
to reduce the risk of damage from surg-
es in telephone and power line current.
These protection circuits meet or ex-
ceed the FCC requirements. However,
lightning striking the telephone or power
lines can damage your TAD.
In the unlikely event that your TAD caus-
es problems on the telephone line, the
telephone company attempts to notify
you in advance. If advance notice is not
practical, the telephone company noti-
fies you as soon as possible and advis-
es you of your right to file a complaint
with the FCC.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug the TAD during storms
to reduce the possibility of damage.
Also, the telephone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this TAD. The telephone
company notifies you of these changes
in advance so you can take the neces-
sary steps to prevent interruption of your
telephone services.
22
NOTES
23
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
04/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
10A99
Printed in China
|