Quantum Garage Door Opener Dynamic Dolphin Remote User Guide

Dynamic Dolphin  
Remote  
Basic Operation Instructions  
 
Dolphin  
Basic Operation Instructions  
3
TABLE OF CONTENTS  
INTRODUCTION ................................................................................ 4  
Dynamic Dolphin Remote ......................................................................... 4  
MAGNETIC KEY LOCK SYSTEM ............................................... 6  
JOYSTICK OONAPU ........................................................................ 6  
DRIVE PROGRAM SELECTION................................................... 6  
ACTUATOR CONTROL.................................................................... 7  
 
4
Basic Operation Instructions  
Dolphin  
INTRODUCTION  
Welcome to Quantum Rehab, a division of Pride Mobility Products  
Corporation (Pride). Quantum Rehab is dedicated to the customization of  
power chairs for users with advanced rehabilitation and mobility issues.  
Quantum Rehab also expands possibilities for enhanced healthcare attendant  
control over power chair functions to provide a secondary level of support  
for our customers where necessary.  
Dynamic Dolphin Remote  
The Dynamic Dolphin Remote is a DX compatible control unit complete  
with a joystick, fully functional keypad, and the capability to support up to  
five different drive programs and several actuator functions.  
This manual is designed to explain basic operation for the following functions  
available with the Dolphin Remote:  
1. Magnetic Key Lock System  
- The user can lock the power chair to prevent unintended use of the  
chair.  
2. Joystick OONAPU  
- OONAPU stands for “Out Of Neutral At Power Up.” This is a safety  
measure designed to prevent unintended movement of the power chair.  
3. Drive Program Selection  
- The user can choose from one of five programs to control the movement  
and speed of the power chair.  
4. Actuator Control  
- The user can control up to five actuators using the Dolphin Remote.  
Figure 1 provides information on the Dynamic Dolphin Remote components  
and connections. Use this diagram to familiarize yourself with the function  
and location of each component before using the Dynamic Dolphin Remote.  
 
Dolphin  
Basic Operation Instructions  
5
Status LED  
Left & Right  
Indicates On/Off Status, and  
flashes to indicate system faults.  
Indicator Switches & LEDs  
Press the appropriate switch to activate  
turn indicator. Press again to turn off.  
LED flashes when activated.  
Battery Gauge  
A series of ten LEDs, which  
indicate charge level  
On/Off Switch  
Toggles the system on or off.  
Drive Program Display  
A 7-segment display shows the  
currently selected drive program.  
Horn Switch  
Press to activate warning horn.  
Light Switch & LED  
Toggles the head/tail/side lights on or  
off. LED is lit when activated.  
Remote Status LED  
Indicates status of Dolphin Remote.  
Drive Program Select Switch  
This switch will scan through and  
select one of five drive programs.  
seat height  
leg rest adjust back tilt  
(right & left)  
seat tilt  
Hazard Light Switch & LED  
Press to make both indicators flash  
simultaneously. Press again to turn off.  
LED flashes when activated.  
Actuator Select Switches  
5 switches for actuator selection. Not used for  
actuator operation, only selection. LED above  
switch lights up when activated.  
Magnetic Key Lock & LED  
Locks DX System to prevent unauthorized use. Upon reactivation of  
unit, LED will flash until magnetic key is used to unlock system.  
Joystick  
Controls the speed and direction of  
power chair, as well as actuator  
control when selected.  
Magnetic Key  
Used to lock and unlock  
the DX System.  
BACK VIEW  
Battery Connection Socket  
Connects to Battery Charger Plug.  
DXBUS Sockets  
Enables DXBUS cable to be used  
to interconnect to the remainder of  
the DX System.  
Figure 1. Dolphin Components and Connections  
 
6
Basic Operation Instructions  
Dolphin  
MAGNETIC KEY LOCK SYSTEM  
1. To arm the locking system, hold the magnetic key on or near the key  
symbol on the Dolphin front panel. See figure 1. The system will beep  
and automatically power itself down. No LEDs should be lit.  
2. To turn the power chair back on, press the On/Off Switch. The system  
will power on, but the locking system needs to be disarmed before normal  
operation can occur. The key symbol will flash, indicating that the system  
should be disarmed.  
3. To disarm the lock, put the magnetic key on or near the key symbol. The  
LED will stop flashing, and normal operation may resume. If the locking  
system is not disarmed within one minute, the Dolphin will shut itself  
off.  
JOYSTICK OONAPU  
If the power chair is powered up while the joystick is not in the neutral  
position, the System Status LED will flash for as long as the condition persists  
up to a maximum of five seconds. After five seconds, a Fault Flash Code is  
signaled on the System Status LED, and the Remote Status LED will flash.  
To clear the fault, power down, put the joystick in neutral, and power the  
system back on.  
DRIVE PROGRAM SELECTION  
The Dolphin can control up to five drive programs. Drive Program 1 is  
configured as the slowest, and Drive Program 5 is configured as the fastest.  
To select the preferred drive program, press the Drive Program Select Switch.  
The selected drive program will be displayed on the 7-segment display. See  
figure 1. Each press of the Drive Program Select Switch will increase the  
drive program to the next level until it cycles back to Drive Program 1.  
 
Dolphin  
Basic Operation Instructions  
7
ACTUATOR CONTROL  
The Dolphin can support the control of up to five actuators if a correctly  
configured actuator control module is present.  
NOTE: Once an actuator is selected, driving will be inhibited until the  
actuator is deselected.  
1. Press the Actuator Switch representing the seat function needing  
adjustment. See figure 2.  
2. Push the joystick full forward or full reverse to adjust the actuator. A  
forward command with the joystick will extend the actuator; a reverse  
command will retract the actuator.  
NOTE: When using the Dolphin in conjunction with a TRx Seating System,  
give a reverse command to extend the actuator, release the joystick, then  
give another reverse command to retract the actuator. The reverse command  
toggles between extend and retract only for TRx units.  
3. Press theActuator Switch again to deselect the actuator and resume normal  
operation.  
Figure 2. Actuator Control Selection  
 
Exeter, PA  
Quantum Hotline: 1-866-800-2002  
Visit the Rehab Zone at:  
INFMANU1756/A/MAY 2001  
 

Radio Shack Cordless Telephone 43 3537 User Guide
Roland Engraver EGX 20 User Guide
Roland MP3 Player AR 200 User Guide
Rotel CD Player RCD 1070 User Guide
Samsung Air Conditioner AM18B1C09 User Guide
Samsung Home Theater System HT X200 User Guide
Sanyo Flat Panel Television CE42FD90T B User Guide
Scion Automobile xD User Guide
Sears Sewing Machine 385 564180 User Guide
Sears Sewing Machine 385 1254180 User Guide