QSC Audio Speaker EB2082 I User Guide

1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA  
Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079  
Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834  
ILA Series Loudspeaker System User Manual  
WL2082-i  
WL115-sw  
FB2082-i  
EB2082-i  
PB2082-i  
full-range line array loudspeaker  
subwoofer line array loudspeaker  
array frame  
extension bar  
pull back bar  
GS115-sw  
ground stack kit  
*TD-000218-00*  
TD-000218-00 revB  
 
Introduction  
The Installation Line Array (ILA) is a high performance line array system designed for the needs of Houses of Worship, Performing Arts  
facilities and a multitude of other venue types. The current ILA family is composed of the WL2082-i line array element, WL115-sw sub-  
woofer, FB2082-i array frame, PB2082-i pull-back bar, EB2082-i extension bar, and GS115-sw Ground Stack Kit.  
Installation Line Arrays may be used in outdoor applications where the system is somewhat protected from the elements. The enclosure  
material is formulated with UV inhibitors, the grille is made of aluminum and the woofer cones are weather resistant.  
WL2082-i  
The WL2082-i line array element uses two high-power, neodymium magnet, 2" voice-coil, 8" low-frequency drivers in a two-and-a-half  
way configuration. Both woofers produce low-frequencies but only one covers the mid-range, resulting in far better horizontal directivity  
control in the crossover region. Excellent high-frequency output and clarity are provided by a pair of 1.75" voice coil, neodymium magnet  
compression drivers with titanium diaphragms. These drivers are mounted to a multiple-aperture diffraction waveguide that provides an  
extremely wide horizontal coverage of 140º. As a result, systems will rarely require side or center fill speakers and solid stereo imaging is  
preserved across the listening area.  
The low-frequency capability of a WL2082-i array extends to 68 Hz (-10 dB); adequate for speech/vocal and acoustic music program mate-  
rial. For reinforcement of program material with more demanding low-frequency content, the WL115-sw companion subwoofer is avail-  
able.  
Figure 1: WL2082-i Loudspeaker  
1- Rigging plate attachment holes  
2- Grille  
3- Splay angle selection holes (rear of rigging plates)  
4- Grille retaining screws (one on each end of enclosure)  
5- Rigging plate retaining bolt  
6- Rigging alignment notch  
7- Rigging plates  
8- Input plate  
9- Rigging alignment pin  
10- Horizontal Shading selector switch  
11- Bi amp/Tri amp Mode selector switch  
12- Wiring table  
13- NL8 Speakon connectors  
3
 
Introduction (continued)  
WL115-sw  
The WL115-sw subwoofer extends the systems low-frequency capability to 35 Hz. with a compact fourth-order bandpass enclosure. Its ceramic  
magnet, 4” voice coil, 15” transducer provides 650 watt continuous power handling capability.  
Many users of line array systems have found that suspending the subwoofers with the array provides audible benefit. Additionally, many venues  
lack physical space for floor-mounted subs. For these reasons, the WL115-sw includes rigging hardware and, with selection of the appropriate  
rigging accessories, subwoofers may be flown at the top of or behind a WL2082-i array.  
Figure 2: WL115-sw Subwoofer  
1- Rigging straps  
2- Ports  
3- Handles  
4- Rigging strap retaining bolts  
5- Driver access panel  
6- Input panel  
7- NL8 Speakon connectors  
8- Wiring table  
Rigging  
Rigging the Installation Line Array is simple and flexible. Enclosures are bolted together with the provided M8 shoulder bolts or pinned  
together with optional quick-release ball-lock pins.  
The FB2082-i array frame supports most flown array applications, and the EB2082-i extension bar supports suspension where the center of  
gravity is beyond the limits of the FB2082-i. Additionally, the EB2082-i is used for arrays where subwoofers are flown behind the main array.  
The PB2082-i pull-back bar is used for pulling back the bottom element of the array for aiming and stability or as the primary suspension com-  
ponent for certain small arrays.  
Ground stacking is easily accomplished using the GS115-sw Ground Stack Kit. The kit includes two ground stack rails which attach to the rig-  
ging straps under the WL115-sw. These rails provide added stability and allow for ground stacked arrays to be constructed.  
4
 
Introduction (continued)  
Figure 3: FB2082-i Array Frame  
1- Shackle holes (accept 3/4” (20 mm) screw pin anchor shackle)  
2- Center support bar  
3- Rigging plates  
4- Rigging plate retaining bolts  
5-Rigging plate attachment holes  
Use only shackle holes for  
suspension of array!  
Figure 4: PB2082-i Pull Back Bar  
1- Shackle hole (accepts 5/8” (16 mm) screw pin anchor shackle)  
2- Rigging plate attachment holes  
3- Rigging plates  
4- Rigging plate retaining bolts  
Use only shackle hole for  
suspension of array!  
Figure 5: EB2082-i Extension Bar  
1- Extension bar  
2- Rigging plate retaining bolts  
3- Shackle holes (accept 3/4” (20 mm) screw pin anchor shackle)  
4- Rigging plates  
Use only shackle holes  
for suspension of array!  
5
 
Introduction (continued)  
Figure 6: GS115-sw Ground Stack Kit  
1- Rail  
2- Rubber foot  
3- Attachment holes  
Rigging the Installation Line Array  
Rules for Suspension  
•Correct use of all suspension hardware and components is imperative in sound system rigging and deployment.  
•Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits.  
•Research local codes and regulations to fully understand the requirements for suspended loads in the venue in which the equipment is to be  
suspended.  
•Use only shackle holes for suspension of array.  
•Be absolutely certain of the integrity of any structural member intended to support suspended loads. Hidden structural members can have hid-  
den structural weakness.  
•Consult a Professional Mechanical or Structural Engineer licensed in the jurisdiction of the sound system installation to review, verify, and  
approve all attachments to the building or structure.  
•Never assume anything- Owner or third-party supplied suspension attachment points may not be adequate for the loads to be suspended.  
•Employ the services of a Professional Rigger for hoisting, positioning, and attaching the equipment to the supporting structure.  
•Always inspect all components (enclosures, suspension brackets, pins, frames, bolts, nuts, slings, shackles, etc.) for cracks, wear, deforma-  
tion, corrosion, missing, loose, or damaged parts that could reduce the strength of the assembly before lifting. Discard any worn, defective, or  
suspect parts and replace them with new appropriately load-rated parts.  
Shock Loading  
When a load is either moved or stopped, its static weight is magnified. Sudden movements can magnify the static weight several times. This  
magnification of static weight is termed "shock loading". Shock loading poses a danger to equipment and workers. The effects of shock loading  
can be instantaneous, or they may remain undetected unless the equipment is visually damaged. Avoiding shock loading requires careful plan-  
ning and knowledge of equipment, rigging, and lifting practices.  
Shock loading of equipment and structures is usually confined to lifting and installation, but natural forces (winds, earthquakes) can impose  
shock loads several times the static load. This is why structures and suspension equipment must be capable of supporting several times the  
weight of the equipment suspended.  
ILA Working Load Limits and Design Factors  
Table 1 lists the ILA suspension components and provides Working Load Limit data at various Design Factors. The tabulated Design Factors are  
for static loads only. The choice of which Design Factor to use will depend upon the jurisdiction and venue of installation, as well as the condi-  
tions of suspension. Dynamic conditions are determined by unknown, installation-specific factors and should be referred to a Licensed Structural  
Engineer for clarification before proceeding with any suspension of the equipment. The data presented is based upon the listed component  
weights:  
6
 
Rigging the Installation Line Array (continued)  
Table 1: ILA Working Load Limits  
Component  
Weight  
5:1 Design Factor 7:1 Design Factor  
10:1 Design Factor  
EB2082-i Extension Bar  
FB2082-i Array Frame  
PB2082-i Pull Back Bar  
WL2082-i Loudspeaker  
WL115-sw Loudspeaker  
38 lb (17.3 kg)  
17 lb (7.7 kg)  
6 lb (2.7 kg)  
2400 lb(1090.0 kg)  
1036 lb (470.9 kg)  
296 lb (134.5 kg)  
889 lb (403.2 kg)  
1036 lb (470.9 kg)  
1404 lb (638.2 kg)  
1714 lb (779.2 kg)  
740 lb (336.4 kg)  
211 lb (96.1 kg)  
634 lb (288.3 kg)  
740 lb (336.4 kg)  
1003 lb (455.8 kg)  
1200 lb (545.5 kg)  
518 lb (235.5 kg)  
148 lb (67.3 kg)  
445 lb (201.8 kg)  
518 lb (235.5 kg)  
702 lb (319.1 kg)  
37 lb (16.8 kg)  
111 lb (50.5 kg)  
not applicable  
1
M8 Shoulder Bolt  
1
not applicable  
not applicable  
not applicable  
not applicable  
2534 lb (1151.8 kg)  
6641 lb (3018.8 kg)  
2721 lb (1236.7 kg)  
1810 lb (822.7 kg)  
4744 lb (2156.3 kg)  
1943 lb (883.4 kg)  
1267 lb (575.9 kg)  
3321 lb (1509.4 kg)  
1360 lb (618.4 kg)  
5677 lb (2580.5 kg)  
M8 Ball-lock Pin  
1
M12 Shoulder Bolt  
1
3/8” Fastener  
1
11354 lb (5161.0 kg) 8110 lb (3686.4 kg)  
7/8” Fastener  
1- Working Load Limits are per fastener loaded in double shear. Data is for informational purposes only.  
Attaching WL2082-i to Array Frame  
Before beginning any installation, have your system designer configure the array with proper  
splay angles using QSCs EASE Focus (Array Calculator). All orientation of product is to be as  
viewed from the rear of the enclosure.  
Figure 7: WL2082-i attached to FB2082-i  
Attach the array frame to the suspension structure using a 3/4” (20 mm) screw pin anchor  
shackle and appropriate sling, cable, etc....  
For arrays of 4 WL2082-i or less, assemble the cluster of WL2082-i on the ground using the  
included mating hardware. Ensure the notched rigging plate is on the right hand side (the sys-  
tem can only be installed one way. Note the QSC logo on the input plate will be right side up  
when the enclosure is oriented properly). During assembly, ensure your splay angles are as  
desired.  
When constructing large arrays it is recommended to first assemble units of four enclosures  
and then assemble the final array by joining the four enclosure units to one another.  
Attachment of one enclosure to another is accomplished by inserting the cap-head shoulder  
bolt with washer through the rigging plate attachment holes and appropriate splay angle  
selection holes in the mating rigging plates and threading the lock nut (nylock) on the inside  
edge of the plates. The bolt should be tightened snuggly to no more than 5 lb-ft of torque (6.8  
N-m). See Figure 7 for assembly detail.  
Attach the array frame to the top enclosure by inserting the cap-head shoulder bolt with  
washer through the appropriate mounting holes and threading the lock nut (nylock) on the  
inside edge of the plates. The bolt should be tightened snuggly to no more than 5 lb-ft (6.8 N-m)  
of torque.  
NOTE: For some array configurations, use of the extension bar and/or pull-back  
may be required to achieve the required aiming angle.  
7
 
Figure 8:PB2082-i under WL2082-i attached to FB2082-i.  
Rigging the Installation Line Array (continued)  
Pull-Back Bar  
If using the pull-back bar, attach to the bottom enclosure at the bot-  
tom-most splay angle adjustment holes at the rear of the rigging plate  
by inserting the cap-head shoulder bolt through the mated pieces and  
threading the lock nut (nylock) on the inside edge of the plates. Use a  
5/8” (16 mm) shackle to attach to the pull-back bar shackle hole  
located in the center of the main bar.  
NOTE: All hardware/components must be rated for the  
expected loads as determined by the Professional Engi-  
neer responsible for suspension.  
NOTE: A washer should not be used when attaching the  
pull back bar. This will allow the pull back bar to pivot  
freely.  
Figure 9: Bolting order for EB2082-i Extension Bar rigging plates.  
Extension Bar  
The extension bar rigging plates can be moved, if required, by remov-  
ing the two 7/8”mounting bolts, moving to the selected mounting  
location, and reattaching. Tightening torque is to be 100 lb-ft of torque  
(135.6 N-m) Ease-Focus software’s center-of-gravity calculator will  
provide a suitable point (or two points) for desired down-tilt.  
Attach the array frame to the extension bar rigging plates by centering  
the array frame member between the extension bar rigging plates and  
bolting together using the supplied 7/8” bolts.  
Attaching the WL115-sw to the Array Frame  
All orientation of product is to be as viewed from the rear of the enclo-  
sure. The QSC logo on the input plate will appear right side up when  
the enclosure is oriented properly.  
Figure 10: Extending the WL115-sw rigging straps.  
1- Attach the array frame to the suspension structure using 3/4" (20  
mm) shackle and appropriate sling, cable, etc....  
2- Refer to Figure 10. For all four rigging straps: Using an 6mm hex  
wrench, remove the upper and lower rigging strap retaining bolts and  
loosen the two bolts in between. Pull the inner and outer straps to  
their outermost position; pull the center strap to its outermost posi-  
tion, and align the retaining bolt holes with the threaded inserts of the  
enclosure. Re-install the outermost rigging strap retaining bolts and  
tighten all four bolts on each strap to 13 lb-ft (17.6 N-m).  
8
 
Figure 11: WL115-sw attached to FB2082-i.  
Rigging the Installation Line Array (continued)  
3- Lower the array frame onto the enclosure, carefully aligning the rigging straps, and  
attach the top enclosure to the array frame by installing the ball-lock pins or M8 bolts.  
Before lifting, ensure the audio connection to the enclosures are correct and functioning.  
NOTE: When attaching one WL115-sw to another WL115-sw, you must use  
the supplied ball-lock pins. This will allow for easier installation given the  
close spacing between consecutive WL115-sw enclosures.  
NOTE: When arraying two or more WL115-sw subwoofers, it is easiest to  
lay the enclosures on their backs, align and mate the rigging straps, and  
install the ball-lock pins. When installing the ball-lock pins, ensure full  
insertion and locking action.  
Figure 12: WL115-sw to WL115-sw rigging.  
Attaching the GS115-sw Ground Stack Rails to a WL115-sw  
1- For all four rigging straps: Using an 6mm hex wrench, remove the upper and lower rig-  
ging strap retaining bolts and loosen the two bolts in between. Pull the inner and outer  
straps to their outermost position; pull the center strap to its outermost position, and  
align the retaining bolt holes with the threaded inserts of the enclosure. Re-install the  
outermost rigging strap retaining bolts and tighten all four bolts on each strap to 13 lb-ft  
(17.6 N-m).  
2- Position a GS115-sw Ground Stack rail between the rigging straps on the right and one  
to the outside of the rigging straps on the left side of the loudspeaker.  
Figure 13: GS115-sw Ground Stack Rails attached to  
WL115-sw.  
3- Attach the rail to the rigging strap by inserting the cap-head shoulder bolt with washer  
through the mated components and threading the lock nut (nylock) on the inside edge of  
the assembly. The bolt should be tightened snuggly to no more than 5 lb-ft (6.8 N-m).  
NOTE: GS115-sw must be attached to at least one WL115-sw for stability  
before any additional loudspeakers are attached. GS115-sw should never  
be attached to a WL2082-i loudspeaker.  
NOTE: GS115-sw is designed to accommodate up to two WL115-sw loud-  
speakers and up to six WL2082-i loudspeakers.  
Attaching WL2082-i enclosures beneath WL115-sw enclosures  
For arrays of 4 WL2082-i loudspeakers or less, assemble the WL2082-i loudspeakers on  
the ground using the included mating hardware. Ensure the notched rigging plate is on the  
right hand side (the system can only be installed one way; the QSC logo on the input plate  
will appear right side up when the enclosure is oriented properly). During assembly,  
ensure your splay angles are as desired.  
When constructing large arrays it is recommended to first assemble units of four enclo-  
sures and then assemble the final array by joining the four enclosure units to one another.  
Attachment of one enclosure to another is accomplished by inserting the cap-head shoul-  
der bolt with washer through the mated rigging plates and appropriate splay angle selec-  
tion holes and threading the lock nut (nylock) on the inside edge of the plates. The bolt  
should be tightened snuggly to no more than 5 lb-ft (6.8 N-m). See Figure 7 for assembly  
detail.  
Figure 14: WL2082-i attached to WL115-sw and FB2082-i.  
Lower the array frame with subwoofer(s) onto the WL2082-i enclosure cluster and attach  
the top enclosure to subwoofer by inserting the cap-head shoulder bolt with washer  
through the mounting holes and threading the lock nut (nylock) on the inside edge of the  
plates and rigging straps.  
NOTE: See Pull-Back Bar and Extension Bar sections on previous page for  
information regarding their use.  
9
 
Rigging the Installation Line Array (continued)  
Figure 15: EB2082-i with WL115-sw suspended at  
rear and WL2082-i array suspended at front.  
Attaching WL115-sw behind WL2082-i array using EB2082-i  
It is sometimes necessary to suspend the subwoofers behind the main array. Extreme  
splay angles may result in physical interference with rear-flown subwoofers.  
Attach both array frames to the extension bar rigging plates by centering the array frame  
member between the extension bar rigging plates and bolting together using the sup-  
plied 7/8” bolts. The extension bar rigging plates can be moved, if required, by removing  
the two 7/8”mounting bolts, moving to the selected mounting location, and reattaching.  
Tightening torque is to be 100 lb-ft (135.6 N-m). Ease-Focus software’s center-of-gravity  
calculator will provide a suitable point (or two points) for desired down-tilt.  
The rear suspended WL115-sw subwoofer(s) may now be attached to the array frame;  
see “Attaching the WL115-sw to the Array Frame”  
The front suspended WL2082-i loudspeakers may now be attached to the array frame;  
see “Attaching WL2082-i to Array Frame”  
NOTE: When stacking loudspeakers for attachment to array frames using  
the extension bar, we recommend working with groups of 2 WL2082-i for  
each WL115-sw. Start with no splay angle; this yields the same height for landing the extension  
bar. Adjust splay angle once the rig is lifted.  
Suspending 4 or less WL2082-i Loudspeakers Using Two Pull-Back Bars  
NOTE: Do not suspend more than 4 WL2082-i loudspeakers from a PB2082-i pull-back bar! Do not  
use PB2082-i pull-back bar for suspending anything other than 4 or less  
WL2082-i loudspeakers! Do not suspend the WL115-sw from the PB2082-i  
pull-back bar!  
Figure 16: Using two PB2082-i Pull Back Bars for  
suspending a maximum of 4 WL2082-i loudspeakers.  
NOTE: A washer should not be used when attaching the pull back bar. This  
will allow the pull back bar to pivot freely.  
Assemble the array of WL2082-i loudspeakers on the ground using the included mating  
hardware. Ensure the notched rigging plate is on the right hand side (the system can only  
be installed one way. Note the QSC logo on the input plate will appear right side up when  
the enclosure is oriented properly.  
Attachment of one enclosure to another is accomplished by inserting the cap-head shoul-  
der bolt with washer through the mated rigging plates and appropriate splay angle selec-  
tion holes and threading the lock nut (nylock) on the inside edge of the plates. The bolt  
should be tightened snuggly to no more than 5 lb-ft of torque (6.8 N-m). See Figure 7 for  
assembly detail.  
Attach one PB2082-i to the top enclosure’s front, top rigging plate attachment holes by  
inserting the cap-head shoulder bolts without washers through the mated pieces and  
threading the lock nut (nylock) on the inside edge of the plates. The bolts should be tight-  
ened snuggly to no more than 5 lb-ft of torque. See Figure 7 for assembly detail. Use a 5/  
8” (16 mm) screw pin anchor shackle to attach to the pull-back bar shackle hole located in  
the center of the pull back bar for lifting.  
Attach the second PB2082-i to the bottom enclosure at the bottom-most splay angle  
adjustment holes at the rear of the rigging plate by inserting the cap-head shoulder bolts  
without washers through the mated pieces and threading the lock nut (nylock) on the  
inside edge of the plates. The bolts should be tightened snuggly to no more than 5 lb-ft  
(6.8 N-m) of torque. See Figure 7 for assembly detail. Use a 5/8” (16 mm) screw pin anchor  
shackle to attach to the pull-back bar shackle hole located in the center of the main bar for  
pulling back.  
Warning! Four (4) WL2082-i loudspeakers  
is the maximum allowable load (10:1  
design factor) for the PB2082-i. Do not sus-  
pend more than four WL2082-i loudspeakers from  
the PB2082-i.  
10  
 
WL2082-i Controls and Connections  
Figure 17: MODE selection switch.  
MODE Selection Switch  
BI AMP: When set to BI AMP, an internal shading net-  
work removes the mid-frequencies from one of the low-  
frequency drivers. The BI AMP HORIZONTAL SHADING  
switch will select which transducer is shaded.  
TRI AMP: Shading network is NOT applied (shading  
must be provided by upstream signal processing). The  
Bi Amp Mode Horizontal Shading selector switch is not  
functional in tri amp mode. Connect to the Speakon as  
shown for tri amp.  
Figure 18: BI AMP MODE HORIZONTAL SHADING selection switch.  
BI AMP MODE HORIZONTAL SHADING  
Selection Switch  
The BI AMP MODE HORIZONTAL SHADING selection  
switch is only functional in bi amp mode. This switch  
determines which low-frequency transducer receives  
only low-frequency program material (shading). The un-  
shaded transducer receives low- and mid-frequency  
program material. This allows switch position selection  
for use as either “house left” or “house right”, without  
the need to flip boxes.  
LF2  
LF1  
NOTE: LEFT and RIGHT markings on the BI  
AMP HORIZONTAL SHADING SWITCH apply  
to the enclosure as viewed from the rear (i.e.  
looking at the Input Plate with the text prop-  
erly oriented).  
Table 2: WL2082-i Connector Pinout for BI AMP and TRI AMP Mode  
PIN  
BI AMP  
TRI AMP  
1+  
1-  
Through  
Through  
Through  
Through  
LEFT: Use this setting to steer coverage to the left (as  
viewed from behind the arrays, looking toward the  
audience).  
2+  
No Connection  
Left Low Frequency  
Transducer + (16 Ohms)  
RIGHT: Use this setting to steer coverage to the right  
(as viewed from behind the arrays, looking toward the  
audience).  
2-  
No Connection  
Left Low Frequency  
Transducer - (16 Ohms)  
3+  
Left and Right Low Fre-  
quency Transducers in  
Parallel + (8 Ohms)  
Right Low Frequency  
Transducer + (16 Ohms)  
Input Connections  
3-  
Left and Right Low Fre-  
quency Transducers in  
Parallel - (8 Ohms)  
Right Low Frequency  
Transducer - (16 Ohms)  
The WL2082-i input connectors are a pair of Neutrik  
NL8's wired in parallel. Connections for biamp and tri-  
amp vary, see Table 2 or the pinout table on the  
WL2082-i input plate (Figure 19).  
4+  
4-  
High Frequency Trans-  
ducer + (16 Ohms)  
High Frequency Trans-  
ducer + (16 Ohms)  
High Frequency Trans-  
ducer - (16 Ohms)  
High Frequency Trans-  
ducer - (16 Ohms)  
The WL2082-i loudspeaker is not equipped  
with a crossover network. All signal pro-  
cessing must be done before connecting  
audio power to the loudspeaker. Do not con-  
nect full-range audio to the high-frequency  
transducer or damage may result!  
Figure 19: Pinout table as printed on WL2082-i input plate label  
11  
 
WL115-sw Connections  
Figure 20: WL115-sw Input Plate  
Input Connections  
The WL115-sw input connectors are a pair of Neutrik  
NL8's wired in parallel. See Table 3 or the WL115-sw  
Input Plate for connector pinout.  
Note pin numbers 2+, 2-, 3+, 3-, 4+, and 4- are  
wired straight through from one connector to  
the other. This accommodates using one input  
cable assembly (where appropriate) for sub-  
woofer and full range loudspeaker connec-  
tions. Additionally, pin numbers 1+ and 1- of  
both NL8s are wired in parallel.  
Table 3: WL115-sw Connector Pinout  
PIN  
Connection  
1+  
1-  
Low Frequency Transducer + (8 Ohms)  
Low Frequency Transducer - (8 Ohms)  
2+  
2-  
Through  
Through  
Through  
Through  
Through  
Through  
3+  
3-  
4+  
4-  
Figure 21: Pinout table as printed on WL115-SW Input Plate  
Neutrik NL8FC Cable Connector Pinout  
Figure 22 shows the pin designations inside the Neutrik  
NL8FC connector. This information is for reference only.  
Diagram is of the connector as viewed from the wire-  
insertion end.  
Figure22: NL8FC pin designations- Plug viewed from the wiring side.  
12  
 
WL2082-i Specifications  
Frequency Response:  
80 - 20,000 Hz (+/- 3 dB)  
68 - 22,000 Hz (-10 dB)  
HF: 126/132 dB  
Frequency Range:  
Maximum SPL (continuous/peak):  
Nominal Coverage (-6 dB included):  
Transducers:  
LF: 122/128 dB  
Horizontal: 140 degrees (500 Hz to 3.2 kHz)Vertical: dependant on cumulative splay angle  
High Frequency:  
Dual 50W, 8 Ohm 1 inch exit, 1.75 inch titanium diaphragm, neodymium magnet assembly  
Dual 200W, 16 Ohm 8 inch cone transducer, 2 inch voice coil, neodymium magnet assembly,  
weather resistant cone  
Low Frequency:  
Acoustic Crossover Frequency:  
Input Sensitivity:  
High to Mid: 2000 Hz  
HF: 106 dB  
Mid to Low: 230 Hz  
LF: 96 dB  
Weight:  
Net: 37 lb (16.8 kg)  
Shipping: 45 lb (20.5 kg)  
Enclosure:  
High-impact Polystyrene with ultraviolet (UV) protectant, paint finish.  
Perforated aluminum  
Grille:  
Connectors:  
Two (2) Neutrik NL8 in parallel (wired as shown in Table 2)  
Working Load Limit Information:  
Component  
Weight  
37 lb (16.8 kg)  
5:1 Design Factor 7:1 Design Factor  
889 lb (403.2 kg) 634 lb (288.3 kg)  
10:1 Design Factor  
445 lb (201.8 kg)  
WL2082-i Loudspeaker  
13  
 
WL115-sw Specifications  
Frequency Response:  
Frequency Range:  
37 - 107 Hz (+/- 3 dB)  
35 - 112 Hz (-10 dB)  
Maximum SPL (continuous/peak):  
Transducer:  
124 dB/130 dB  
650W, 8 Ohm 15 inch woofer, 4 inch voice coil, ceramic magnet assembly  
Recommended Crossover Frequency:  
Input Sensitivity:  
35 - 85 Hz  
96 dB  
Weight:  
Net: 111 lb (50.4 kg)  
Shipping: 121 lb (55.0 kg)  
Enclosure:  
0.708 inch (18 mm) Baltic birch plywood, paint finish.  
Connectors:  
Two (2) Neutrik NL8 in parallel (wired as shown in Table 3)  
Working Load Limit Information:  
Component  
Weight  
111 lb (50.5 kg)  
5:1 Design Factor 7:1 Design Factor  
1036 lb (470.9 kg) 740 lb (336.4 kg)  
10:1 Design Factor  
WL115-sw Loudspeaker  
518 lb (235.5 kg)  
14  
 
EB2082-i Specifications  
Material:  
Aluminum 6061-T6  
Finish:  
Black powder coat (White optional)  
Working Load Limit Information:  
Component  
Weight  
38 lb (17.3 kg)  
5:1 Design Factor 7:1 Design Factor  
2400 lb (1090.0 kg) 1714 lb (779.2 kg)  
10:1 Design Factor  
EB2082-i Extension Bar  
1200 lb (545.5 kg)  
FB2082-i Specifications  
Material:  
Aluminum 6061-T6  
Black powder coat (White optional)  
Finish:  
Working Load Limit Information:  
Component  
Weight  
5:1 Design Factor 7:1 Design Factor  
1036 lb (470.9 kg) 740 lb (336.4 kg)  
10:1 Design Factor  
FB2082-i Array Frame  
17 lb (7.7 kg)  
518 lb (235.5 kg)  
15  
 
PB2082-i Specifications  
Material  
Aluminum 6061-T6  
Finish  
Black powder coat (White optional)  
Working Load Limit Information:  
Component  
Weight  
6 lb (2.7 kg)  
5:1 Design Factor 7:1 Design Factor  
296 lb (134.5 kg) 211 lb (96.1 kg)  
10:1 Design Factor  
PB2082-i Pull Back Bar  
148 lb (67.3 kg)  
GS115-sw Specifications  
Material  
Aluminum 6061-T6  
Finish  
Black powder coat (White optional)  
5 lb (2.3 kg) per set  
Weight  
16  
 
17  
 
18  
 
19  
 
How to Contact QSC Audio Products  
Mailing address:  
QSC Audio Products, Inc.  
1675 MacArthur Boulevard  
Costa Mesa, CA 92626-1468 USA  
Telephone Numbers:  
Main Number  
(714) 754-6175  
Sales & Marketing  
Customer Service  
(714) 957-7100 or toll free (USA only) (800) 854-4079  
(714) 957-7150 or toll free (USA only) (800) 772-2834  
Facsimile Numbers:  
Sales & Marketing FAX  
Customer Service FAX  
(714) 754-6174  
(714) 754-6173  
World Wide Web:  
E-mail:  
QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA  
©2006 “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office.  
 

Radio Shack Video Game Controller 26 447 User Guide
RCA CRT Television F27338 User Guide
RIDGID Saw R4516 User Guide
Rival Toaster 16042 User Guide
RocketFish Digital Camera RF WEB2C User Guide
Roland Drums SPD 20 User Guide
Roper Range SEP340X User Guide
Schwinn Motor Scooters Mobility Aid 50GR06BL User Guide
Sears Garage Door Opener 13953716 User Guide
Sennheiser Headphones HD 448 User Guide