QT17D324SC
User’s Manual
Contact Us:
Q-See Products
8015 E. Crystal Dr
Anaheim, CA 92807
Website:
Customer Service:
Phone: 877-998-3440 x 538
Email: [email protected]
Tech Support:
Phone: 877-998-3440 x 539
Email: [email protected]
Fax:
714-998-3509
Rev 061609
QT19D328SC User’s Manual
IMPORTANT SAFEGUARDS
CAUT ION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK,DO NOT REMOVE THE BACK.
NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
Graphic Symbol Explanation
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of un-insulated dangerous voltage within the Product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to people.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance
Warning - To Prevent Fire Or Shock Hazard, Do Not Expose This Monitor To Rain Or Moisture.
This Product Must Be Grounded.
Product Specifications Are Subject To Change Without Notice.
CAUTION: This equipment is to be opened by ONLY by a qualified service person. There are no user serviceable parts
inside. Opening this equipment may expose you to dangerous voltage and other risks. Incorrect re-assembly of this
equipment may result in electric shock.
1．Read lnstructions: All the safety and operating instructions should be read before the appliance is operated.
2．Follow lnstructions: All operating and use instructions should be followed.
3．Cleaning: Unplug this monitor from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or
aerosol cleaners.
4．Water and Moisture: Do not use this monitor near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in
a wet basement, swimming pool, or any other wet surface.
5．Accessories: Do not place this monitor on an uneven surface. The monitor may fall, causing serious injury and serious damage
to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the supplier, or sold with the monitor.
6．Ventilation: Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the monitor, and to
protect it from overheating. These openings should never be blocked by placing the monitor on a bed, sofa, rug, or other
similar surfaces. This monitor should never be placed near or over a radiator or heat register. This monitor should not be
placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or supplier instructions have
been adhered to.
7．Object and Liquid Entry: Never push objects of any kind into this monitor through the openings as they may touch
dangerous voltage points or short-out parts that would result in a fire or electric shock. Never spill liquid of any kind on the
monitor.
8．Repair (Servicing): Do not attempt to repair this monitor yourself as opening or removing the cover may expose you to
dangerous voltage or other hazards. Refer to qualified service personnel.
9．Replacement Parts: Please contact Q-See for replacement parts.
3
QT19D328SC User’s Manual
10．Safety Check: Upon completion of any service or repair to this monitor, ask the service technician to perform safety checks
to determine that the monitor is in proper operating condition.
11．Retain Instructions: The safety and operating instructions should be retained for future reference.
Chapter 1 Product Information
1.1 Product Description
This product is a four channel digital monitoring product that is specially designed for the security industry. It has
an embedded processor and operating system, and also uses the most advanced technologies in the IT field, such
as MPEG-4 video and audio compressing & decompressing, recording to large volume hard drive, TCP/IP network
and other technologies. The firmware encoded in FLASH memory has changed the traditional mode of Monitor with
DVR. It integrates the Monitor with the DVR instead，which not only is more convenient for users to operate but also
makes the system more stable and easier to maintain.
1.2 Product Features
This product uses a high-speed embedded processor and a real time operating system, it offers high stability,
high durability, is crash free and also easy to maintain.
Easy to install and use.
Two levels of password protection, administrator and user guarantee the security of the system.
The system uses an OSD (On Screen Display) graphical interface, which is more
convenient for
operators to use.
The system uses pure hardware MPEG-4 Changeable stream or fixed stream video compression，and
supports HD1 and CIF resolution recording on each channel, the frame rate for recording is adjustable, from
high sharpness to super-low hard drive space usage.
Uses FAT32 format for storage, and can use one IDE hard drive up to 300GB.
Four channels video input, two channels video output，one channel VGA output；Two channels audio input,
two channels audio output, and one USB Port.
Three channel alarm input, one channel linkage alarm output and one channel trouble alarm output.
Real time monitoring and playback in single picture mode, dual channel mode or quad mode .
The system supports turning the machine on and off automatically. In case of power outage, it resumes
recording automatically once the power is restored. Alarm will go off automatically when no video signal is
being received. This eliminates the need to frequently monitor the system.
Manual recording, scheduled time recording, alarm recording, and motion detection recording. Alarm and
motion detection recording saves hard drive space allowing you to record for longer periods of time.
Using the motion detection recording function, you can setup the areas of the camera view that you want to
be sensitive to motion.
The system supports pre-alarm recording and post alarm recording periods.
Equipped with 2x, 4x times fast forward/ fast reverse play functions and 1/2x, 1/4x, 1/8x speed slow motion
reverse play, pause, frame by frame play and other playback control functions.
The system supports PAL and NTSC systems, so the system can be used universally.
Brightness, contrast, Color and Tint can be setup independently for each channel.
Alarm log and operating log facilitates convenient analysis and searching.
RJ-45 universal network telecom interface，network transmitting ways include ADSL, ISDN, LAN and CAN.
The included client software allows long-distance monitoring and playback over the internet, and supports
TCP/IP, UDP/IP and many other net transport protocols.
4
QT19D328SC User’s Manual
RS-485 interface on the system can be used to control P.T.Z cameras with various communication protocols.
VGA output supports 720×480, 1280×720 and 1920×1080 Resolution modes，better quality picture can be
attained by using progressive scanning.
Supports file backup to IDE hard drive.
Equipped with USB2.0 port which can be used for backup to your PC or laptop directly from the DVR hard
drive.
Chapter 2 System Installation
2.1 Installing the Hard Drive
Note: please set the hard drive to “Master” mode when connecting to the DVR.
2.2 Rear Panel Layout
VIDE
O1
1
3
2
4
VIDEO OUT
1
2
USB
NET
AUDIO IN
R
L
L
AUDIO OUT
R
VGA
ALARM
VIDEO IN：1～4 Video Input
VIDEO OUT：1～2 Video Output
USB：One Channel USB terminal input
NET：One Channel NETWORK terminal Input
5
QT19D328SC User’s Manual
AUDIO IN：One Channel left/ One Channel right audio input
AUDIO OUT：One Channel left/ one Channel right audio output
VGA：One Channel VGA terminal input
6
QT19D328SC User’s Manual
Chapter 3 System Operation
3.1 Layout of Front Panel and Remote Control
3.1.1 Front Panel
POWE R
H.D.
ALARM
NET
IR
Buttons on front panel and their functions:
① Indicating light area
NET：indicating light for network activity
ALARM：indicating light for alarm activity
The alarm light will be on once the alarm is started（no matter what kind of alarm it is for）
H.D. ：Indicating light for Hard Drive activity
The light turns on when Hard Drive reads and writes data.
POWER ：Indicating light for power
The light turns red when the power is on；
② Buttons area
Menu operating buttons
：UP Directional button；
：Down Directional button；
：Left Directional button；
7
QT19D328SC User’s Manual
：Right Directional button
【
】button：for confirmation，choose the menu items, and press this button to enter into the selected
sub-menu；Pressing this button can display the real time of the system when playing back
recordings.
Functional Buttons Area
【
【
【
】Button：Main Menu, used for setting each function of the system.
】Button：Play the existing recordings on the hard drive.
】Button：Search button，used for checking recorded information on the hard drive.
【
】Button：Exit button，exit from the current operating menu to last selected menu.
【
】Button：Recording button, manual recording on all four channels can be started at the same time when the
screen is in quad mode, dual views manual recording can be started when the screen is under two
channel surveillance mode；Single channel Manual recording can be started when the monitor is
under single channel surveillance mode.
【
【
【
【
】Button：For stopping the recording button and the manual recording.
】Button：Fast Rewind button, at speed of X2 and X4 times.
】Button：fast forward button，Play the recorded picture fast forward at speed of X2 and X4 times.
】Button：Press this button continuously to see the picture frame by frame.
【
】Button：Used for switching between quad, dual and single picture mode；in the following order:
Channel 1→ Channel 2→ Channel 3→ Channel 4→Dual Views (Channel 1- Channel 2) → Dual Views (Channel 3-
Channel 4) → quad→Channel1
8
QT19D328SC User’s Manual
3.1.2 Remote Control
9
QT19D328SC User’s Manual
L OGI N/ L OCK
P O WE R ON
PLAYBACK
3
6
9
2
5
1
4
7
QUAD
PARAMETER
ANALOG
8
0
+
Z OOM+
Z OOM-
FOCUS-
FOCUS+
EXI T
AUTO
PLAY
F WD
RECALL
S WI T C H
PRESET
SL OW
REV
CF
NET
SET UP
RECORD ST OP
F2
F3
F4
F1
Buttons on Remote Control and Their Functions:
10
QT19D328SC User’s Manual
① Digital ButtonArea
【0-9】Button：Digital buttons，used for digital input or video switch，when in quad mode, press 1,2, 3, 4 digit
buttons to switch the picture output between the first, second, third and forth video channels.
【+】【 -】Button：Adjusting various parameters；
Menu Operating Buttons Area
：UP Directional button；
DOWN Directional button；
LEFT Directional button；
RIGHT Directional button；
【ENTER】button：for confirmation，choose the menu items, and press this button to enter into the selected
sub-menu；Pressing this button can display the real time of the system when playing back the
recordings；
③ PTZ control function buttons
【ZOOM+】,【ZOOM-】Button：Adjust the distance of the picture；
【APERTURE+】,【APERTURE-】Button：Adjust the brightness of the picture；
【FOCUS+】,【FOCUS-】Button：Adjust the sharpness of the picture；
【AUTO】Button：Control automatically；
【RECALL】Button：Standby button in control of PTZ；
【PRESET】Button：Preset control on PTZ, standby button；
【SWITCH】Button：Control on some assistant switch；
④ Play function buttons
【PLAY】Button：Play the recordings on the hard drive；
【SLOW】Button：Play the images slowly，at speed of 1/2x, 1/4x, 1/8x times，or press【play】button to return
to normal playing speed；
【PAUSE/SETP】Button：Press one time to Pause the video，when pressing continuously， picture will be
11
QT19D328SC User’s Manual
displayed frame by frame，press【Play】button to return to normal speed；
【FWD】Button：Play fast forward through the playback video，at the speed of 2x, 4x times，press【Play】
Button to return to normal speed；
【REV】Button：Play fast backward through the playback video，at speed of 2x, 4x times，press【Play】Button
to return to normal speed；
⑤ Other function buttons
【POWER/ON】Button：for turning the machine on and off（Standby and start）；
【LOG IN/LOCK】Button：get the operating rights，to type in the password and lock operation；
【PLAYBACK】Button：for reviewing the recordings, log, state of hard drive, information of software edition
and so on；
【QUAD】Button：For switching display between quad, dual views and single picture；Order of Display:
Channel1→Channel 2→Channel 3→Channel 4→Dual views (Channel 1-Channel 2)→Dual
views (Channel3-Channel 4) →Built-in quad→ Channel 1
【ANALOG】Button：display the brightness, contrast, color and tint, adjusting its parameters using the【+】,
【-】 buttons（This operation can only be performed when you are in single picture mode
and the channel can not be recording at the time）；
【EXIT】Button：Exit button， Exit from the operating menu, return to the last selected menu.
【CF】Button：Enter into the standby menu for recording material, copy the files on the hard drive to the
backup port.
【LANGUAGE】Button：Enter into “language selection” menu to setup the language.
【NET】Button：Standby button；
【RECORD】Button：Start manual recording in single, dual or quad mode.
【STOP】 Button：Stop manual recording in single, dual or quad mode.
【SETUP】Button：When logged into the system, press this function button to enter into the menu setting of
12
QT19D328SC User’s Manual
the system；
【F1】Button：For pick time play on the recorded pictures；
【F2】Button：Press this button to enter into the control menu for PTZ cameras when under the single
channel mode.
Press left, right, up and down buttons to change the position of the PTZ camera；
Press【Zoom+】,【Zoom-】Button：Adjust the distance of the picture；
Press【Aperture+】,【Aperture-】Button：Adjust the brightness of the picture；
Press【Focus+】,【Focus-】Button：Adjust the sharpness of the picture；
Press【Assistant】Button：Control on some assistant switch；
Press【Auto】Button：Control automatically；
Press【Event】Button：standby button in control of PTZ；
Press【Preset】Button：Preset control on PTZ, standby button；
Press the 【F2】button again or 【Exit】 button to exit the setting for the PTZ control menu；
【F3】Button：Standby Button.
【F4】Button：Switch between the monitor and VGA output；
Operating function：Press 【F4】button in remote control unit to switch between output of monitor
and output of display while monitoring cameras. Its order is: output of monito→r VGA 1→VGA
2→VGA 3；There are three modes for VGA output, to adjust to different VGA resolutions.
3.2 Accessing the System
3.2.1 System Start
After supplying power to DVR, the system enters into stand-by state（the power indicating light is on solid red).
After pressing the 【on/off】button on the remote control unit，the system starts，video is displayed on the
screen in quad mode，the number showing in each frame is its video input channel No.， the time will be displayed on
the top center of the screen.
13
QT19D328SC User’s Manual
Note: If time recording has been setup on this machine，and power is connected during this period, then
the machine will start and enter into quad mode directly without needing to press【on/off】button again to start
the machine.
If the channel numbers and time are not being displayed, please press【ENTER】 button on the remote control
unit or panel, and the channel numbers and time will be displayed on the screen.
NOTE: If the hard drive has not been installed before turning on the system，or the hard drive is not
detected by the system after turning it on，the monitor with hard drive will set off the alarm，Please log into
the system to turn off the alarm.
3.2.2 System Login
Note: Pre-delivery code for this system is：000，the default password for administrator is 88888888，and it is
00000000 for user. Administrator has all operating rights. In order to insure secure running of the system,
administrators should change its code and default password of the machine as soon as possible.
When the host machine is started，user can only operate the system when logged in (if the
password is effective). If there is no activity within 100 seconds after logging in, the system will enter into lock
up state！
When the machine is just started or under lock up state, press the 【Login/Lock】Button on Remote Control
Unit，the login interface will appear on the screen, type in the code of the system（Pre-delivery setup：“000”）， and then
type in the password（password for administrator or user of this machine）.
⑴ If correct user’s password is typed in，the monitor will show “Password Correct” message on the screen，and
then after [Return] for confirmation，users can operate each of the items within the permitted fields (the default
password for user is：00000000).
⑵ If correct administrator’s password is typed in，the monitor will show “Password Correct” message on the
screen，and then after [Return] for confirmation，administrator can do all of the operations on the system（The
default password for administrator is：88888888).
3.2.3 System On and Off
When the system is monitoring video, please press the 【on/off】button in the remote control unit twice if you
14
QT19D328SC User’s Manual
want to turn off the system， the system will change into standby mode from running mode when it is off；If you want
to restart the system, please press the 【on/off】button on the remote control.
3.3 Using the System
When the system is running, press 【setup】 button to enter into the OSD main menu. Use the “
,
,
,
” directional buttons on the remote control unit to go to the desired menu，Press【ENTER】 to enter into each
menu, the menu options will be explained one by one in the next section.
3.3.1 System Set
Move the cursor to the position of 【System setup】, (the color of the characters turns blue with white bottom)，
Press【ENTER】button to enter into its settings or sub menu，after entering into the sub-menu，highlight the items
with cursor keys to change the settings.
System Setup
Time：2006.03.30. 09:23:08 Friday
Machine No：001
Machine Address：
HDD overwrite：Yes
System： PAL
NTSC
Password Enable： Yes
No
Admin Pwd Modify Operate Pwd Modify
H.D format
Default Setup
Return
Move the direction key to each sub-menu and press enter for setting.
a). Time: When you have adjusted the year, month and day, the time will appear automatically. Move the cursor where you want
to make the changes and press enter for adjusting or type in the numbers using the remote control.
15
QT19D328SC User’s Manual
b). Machine’s device number: Use can use numbers from “000” to “999”. Machine’s device number has been preset to “000” at
the factory. You need to input this number when the system is running.
c). Machine’s address: Manually enter the machine’s address here (optional). Machine address could be the address of the place
being monitored thru this system. Move the cursor to the “address” line and press enter to enter the address and press enter
again when finished. Use the remote control to enter the numbers and letters. The number keys can be used for letters similar
to the keys on a standard telephone. For example “2” represents 2abc etc.
Note: The length limit is 8 characters or 4 words.
d). HDD overwrite: You have two options – “Yes” & “No”. When “Yes” is selected, it will allow recording continuously even
after the hard drive is full and video will be recorded in FIFO (First-in-first-Out) format; When “No” is selected, it will stop the
recording function once the hard drive is full.
e). Video System: The video system can be changed from NTSC to PAL and vice versa using the left and right arrow keys on the
remote.
f). Modify the administrator Password: Press enter to access the option to reset the administrator password. You can press the
number keys on the remote control to enter the new password .
Please note that only the administrator has the authority to do change this password.
g). Operator Password: Press enter to access the option to reset the operator password. You can press the number keys on the
remote control to change the password. Press the Enter key to save this setting.
Note: Please memorize your password and save it in a secure place to avoid others from accessing it.
h). HDD format: Use this function to format the hard drive.
Warning: All the data on the hard drive will be lost.
i). Default Setup: This function will reset the system to factory settings
j). Return: This function takes you back to the Main Menu.
3.3.2 Channel Set
The channel setting includes channel name, screen display, clock insert, TV screen cover, etc.
Channel Setup
CH
1
2
3
4
Title
Whse
CH name Time InSert
Mask
Off
On
Off
Off
CH View
Allow
Allow
Allow
Blind
On
Off
Off
Off
Off
Top
Bottom
Off
a). Channel: Indicates the channel number. If it has a “X” symbol in front of the channel number it indicates an invalid channel.
Note: For each channel it means the channel can not record video. However you can still see the camera image under monitoring
status if the channel has an image signal but, the system will not prompt the alarm message if the image signal of this TV screen
has lost.
b). Title: Name of the channel. Enter the title of the camera location. Move the cursor to this topic and press enter and enter the
channel title. Use the remote control to enter the numbers and letters. The number keys can be used for letters similar to the keys
on a standard telephone. For example “2” represents 2abc etc. When you have finished press enter.
c). Screen display: Two choices are switch on or switch off. If you choose switch on, it will show the channel title while
monitoring. If you choose off, it will not show a channel title while monitoring.
d). Time Insert: There are three choices for users Off, Bottom, or Top. If you choose Top, the system will insert the time at the
top of the TV screen. If you choose bottom, the system will insert the time at the bottom of the TV screen. If you choose off, the
system will not display the time on the screen.
e). Mask: Two choices for users are switch on or switch off. You can press enter to change the setting. TV mask is used to
hide an area of the camera view that you do not want to appear on the TV screen. When you select Yes the screen will appear with
a white square. You can use the direction keys on the remote and the enter button to select the area you want to mask, and then
use the exit button on the remote to return to the previous screen.
f). Channel View: Two choices for users are allow or blind. You can press enter to change the setting. Choose Allow to display
the video from the camera on the TV and Blind if you do not want the video from the camera to appear on the TV. If you select
16
QT19D328SC User’s Manual
Blink the video from the camera will still be recorded.
3.3.3 Alarm Set
Alarm/Timing Setup
Port Alarm Mode Timing Setup
1
2
3
4
On
On
Off
Off
Close Record Delay: 030
Open Output Delay: 010
Close Buzzer Duration: 000
Close I/O Alarm Out: On
Motion Alarm Out: On
a). Terminal Port: 1,2, 3, 4 represent the 4 outer I/O alarm input ports.
b). Alarm：Two choices are On or Off. Users have the option to turn on /off alarm for each channel
c). Input Mode: Two choices are Close/Open, closed circuit and open circuit. Users have the option to Normally Closed or
Normally Open alarms.
d). Record Delay: Record delay is the length of time the DVR keeps the file open once the alarm has stopped before starting a
new file with the next detected alarm event. The options are from 10 to 300 sec.
e). Output Delay: Under the alarm recording mode, the system is communicating the alarm output signal with the alarm output
end point automatically after moving the testing signal has received the alarm signal from the I/O. Delay the alarm output
means delaying the continuous time of the alarm’s output signal.
f). I/O alarm output: Two choices are On or Off. This option opens or closes the option to send a signal from the DVR to
another alarm device.
g).Motion alarm output the same as the above except for built-in motion detection instead of an external alarm sensor.
3.3.4 Work Set
Record Setup
Channel
Schedule
Setup
Setup
Setup
Setup
Area Set
Setup
Setup
Setup
Setup
1
2
3
4
Return
The Work Set Menu includes scheduling recording for each channel and the option to set up the senitive area for each channel for
motion detection.
The specific operation of each function is given below:
17
QT19D328SC User’s Manual
I. Setting the recording time: Press Setup for each channel under “Schedule” to setup the day (Mon-Sun), Time of First Segment,
recording mode (Time, Alarm or motion) Time of Second Segment, and type of recording mode. There are 2 segments of
recording to accommodate recording overnite. For example, if you start recording at 11:30pm on Monday and stop at 11:00am
on Tuesday, the first set will be 11:30pm to 11:59pm and the second set will be 12:00am to 11:00am.
II. Setting Recording Area:
The sensitivity area of the screen is made up of 192 small areas. The light green represents the area that has not be selected; the
purple area represents the area that has been selected; the small purple square represents the present position of the cursor. To
setup the area you want to be sensitive after you go into the setting interface; the purple small square will be flickering between
two colors alternatively which are purple and green. Use the direction keys and enter button to switch the squares of the area you
want to be sensitive to purple.
3.3.5 PTZ Set
PTZ Setup
Channel Protocol Baud Rate ID
1
2
3
4
Pelco-D
Pelco-D
Pelco-D
Pelco-D
9600
9600
9600
9600
01
63
63
63
Return
By moving the cursor to PTZ Set and pressing [ENTER] key you can enter into quad channel Pan/Tilt/Zoom port setting interface
1.Channel: Denotes systems channel number.
2.Protocol: Denotes the communication protocol between the DVR and camera. By moving the cursor to this column and
pressing the [ENTER] key you can choose the protocol you want to use from the following options:
（Pe1co-D/P/09-15/Dscp/FastDome/PIH1016-1017/JECFastD/RM110/Neocam），
The protocol you select must match a protocol that is available on the camera or the DVR will not be able to communicate with
the camera.
3.Baud Rate: Denotes communication speed between the DVR and camera. By moving the cursor to this column and pressing the
[ENTER] key you can choose the baud rate you want to use from the following options: (1200/2400/4800/9600), the baud rate
you select must match the camera’s baud rate or the DVR will not be able to communicate with the camera.
4.Camera ID: By moving the cursor to this column and pressing the [ENTER] button you can select the ID number you want to
use to communicate with the camera. The options are: (01-63). You must set the same ID number on the DVR and the camera. All
PTZ cameras attached to the DVR must have a different ID number. They can have the same protocol and baud rate, but they
have to have different ID numbers so the DVR can determine which camera it is communicating with. The ID number can match
the channel number, but it does not have to as long as the ID number in the DVR settings and the camera are the same.
5.After completing all of the settings move the cursor to [RETURN] and press the [ENTER] key to return to the previous menu,
and save the Pan/Tilt/Zoom camera settings.
Attention: Pan/Tilt/Zoom protocol, baud rate, and ID number in the DVR must match the settings on the camera
or the DVR will not be able to communicate with the camera.
Pan/Tilt/Zoom operation: After setting Pan/Tilt/Zoom parameters correctly, press [F2] key on the remote control under
single monitoring mode, the top left corner of screen will display “Pan/Tilt control” message temporarily, then you can operate
the channels Pan/Tilt/Zoom camera by pressing the keys on the remote control and front panel.
Pressing [F2] once more will exit Pan/Tilt/Zoom operation, and return to single image monitoring mode; Switch monitoring
image and pressing [F2] key can enter into another channels Pan/Tilt/Zoom operation.
Warning 1: When operating Pan/Tilt/Zoom function, system can not startup manual video recording function.
Warning 2: When operating Pan/Tilt/Zoom function, once system starts up video recording (timing or alarm startup), you
temporarily can not use Pan/Tilt operation.
18
QT19D328SC User’s Manual
Troubleshooting: When Pan/Tilt/Zoom does not operate normally, Please check RS-485 connection and Pan/Tilt/Zoom setup.
3.3.6 Network Set
Move the cursor to Network Set and press Enter to get into the system’s network setup menu.
See picture below:
Network Setup
IP Address:
Subnet Mask:
192.168.001.200
255.255.255.000
Default Gateway: 192.168.001.001
Bandwidth:
Video Port:
Web Port:
Setup
08080
08100
Return
a). IP address: Enter an IP address that will work with the settings on the router you attach the DVR to.
b). Subnet Mask: Enter the Subnet Mask from the router the DVR is attached to.
c). Default Gateway: Enter the Default Gateway from the router the DVR is attached to.
d). Bandwidth: This feature can be used to set the speed of transfer of data over the network or internet. The options are 384kt,
512kt, 1Mt, 2Mt. The lower the setting the lower the bandwidth needed to transfer the video but the video quality will be less, the
higher the setting the more bandwidth needed but the quality of the video will be higher.
e). Video Port: If you are connecting through an Internet Explorer browser set to 06101, if connecting through the client software
program set to 08080
f). Web Port: Set to 08100 for Internet Explorer or client program.
NOTICE: Refer to the Internet Quick Start Guide for information on setting up the DVR for remote access.
3.3.7 System Info
Moving the cursor over [System Info] and pressing the [ENTER] key will enter into system information interface shown
below:
NOTICE: You can also get to this screen by pressing the CHECK button on the remote control while the DVR is in
preview mode.
19
QT19D328SC User’s Manual
Search Menu
Playback All Record
Log
Record Status
HDD Status
Machine Info
Exit
a). Playback All Record: Use this option to search for recordings by record type (All, Timing, Alarm) and Date/Time.
Date Time: Move cursor to this selection, and directly input the date and time, based on the recording date and time you want to
playback;
Now press [START] to see the available recording for that duration. If there is no record found, it will say “No Record”
When selected date has video record, it will display the screen below:
2009-06-17 All Record
01 02 03 04 05 06 07 08 09 10 11
12 13 14 15 16 17 18 19 20 21 22
UP DN 23 24 25 26 27 28 29 30 31
1 00000000 08：00 - 09：00 A 25
1 00000000 09：00 - 10：00 R 25
You can also scroll through other dates during the month to view the recording. If the date is in yellow color it means that there
is a recording for that particular day. Press [ENTER] to view the available recording for that day.
b). Log: Use this option to search the system log by type of event (All, Alarm, Motion Detection, Operation) and Date
Moving cursor to [LOG] item, and pressing [ENTER] key will enter into inquiry log interface
Input Date and Type of the Log
Type: All Events
Date: 2009-06
Start
Return
QT19D328SC User’s Manual
Type: includes all events recording mode, alarm mode, motion detection and operation mode; select the type of event you want,
or select All Events and click start, the screen below will be displayed:
Log Search: All Events
06-17 12:20
06-17 01:00
06-17 02:15
Motion Detect 1
Parameter Set 5-01
Video Loss 2
Return PageUp
PageDown
c). Record Status: Current Recording Settings on the system.
By moving cursor to [Record Status] option, and pressing [ENTER] key you will enter into record status interface, this
screen will display video recording status, including video record mode, status, image quality, and frame rate.
Channel Status
Mode
Quad
Status
Q Frame Alarm Motion
30 Disar Off
Return
Record
5
1) Mode: Displays current recording mode, Single mode, dual mode, quad image
21
QT19D328SC User’s Manual
2）Status: video status: Record/Idle
3）Image Quality: displays video record quality
4）Frame rate: displays video recording frame rate
5）Alarm: setting status alarm/disarm alarm two
6）Motion detection: turn on/ turn off.
d). HDD Status: By moving cursor to [HDD Status] option, and pressing the [ENTER] key you will enter into the hard drive
status information, this window will display current hard drive status, including total capacity and remaining space.
HDD Status
HDD
1
Status
Record
Capacity
249G
Free_Space
169,069MB
2
3
4
None
None
None
000G
000G
000,000MB
000,000MB
000,000MB
000G
Return
e). Machine Info: By moving cursor to [Machine Info] option, and pressing the [ENTER] key you will enter into the machine
information screen. This screen will display the current software version (firmware) and MAC address information (network).
Version: 6214C-P-01.010
MAC Address: 000.111.111.111.110
Return
You can change the MAC address by pressing [ENTER] key and entering numbers.
Note: only super user can hold changing MAC address authority
f). Exit: Moving cursor to this selection item, and pressing the [ENTER] key to confirm will exit to inquiry menu, and exit to
monitoring screen.
22
QT19D328SC User’s Manual
3.3.8 Basic Set
By moving the cursor to [Basic Set] option and pressing the [ENTER] key will take you to the basic setup screen:
Basic Setup
Record Settings:
Buzz Settings:
Setup
Off
Language Settings:
Fastigium Settings:
English
On
Record Bag Settings: 30 minute
USB Settings: Setup
Video Spot Settings: 05 Second
Return
A). Record Settings: Selecting Setup and pressing the enter key display the screen below:
Record Setup
Quality:
Frames: 30 (Global)
Mode: VBR
Return
5
1) Quality: You can select from 1 to 8, The smaller the number the higher the image quality.
2) Frames: The number of frames per second recorded from the cameras, the options are 8, 15, and 30. The more frames
per second, the smoother the video, the lower the frames per second the more video files you can save on the hard drive.
3) Mode: The bit rate format, there are 2 options, VBR (Variable Bit Rate), or CBR (Constant Bit Rate). With VBR the bit
rate decreases when there is less motion and increases when there is more motion, so the quality of the image is less
when there is less motion, and the quality is better when there is more motion. This can save hard drive space since
smaller files are sent to the hard drive when there is no motion. With CBR the bit rate is always the same.
4) Buzz Settings: The options are On or Off. If the setting is on the buzzer will sound if there is a hard drive error or
password error.
5) Language Settings: There are 2 choices, English and Chinese.
6) Fastigium Settings: This setting prevents the monitor from going into sleep mode. By default the setting is On and
the schedule is set for all day everyday. If you switch it to Off then the monitor can go into sleep mode and you will need
to power the system off and back on to display the screen. To see the schedule, go to the On setting of the Fastigium line
and press the enter button 3 times to display the following screen:
Fastigium Time Setup
Week
First_Period Second_Period
00:00-00:00
Everyday 00:00-23:59
******** 00:00-00:00 00:00-00:00
******** 00:00-00:00 00:00-00:00
******** 00:00-00:00 00:00-00:00
******** 00:00-00:00 00:00-00:00
******** 00:00-00:00 00:00-00:00
******** 00:00-00:00 00:00-00:00
******** 00:00-00:00 00:00-00:00
Return
B) Record Bag Settings: This option determines the length of the recorded files when you are recording manually. The
options are 30, 45, and 60 minutes. As an example, if you select 30 minutes after recording for 30 minutes the system
23
QT19D328SC User’s Manual
will start a new file.
C) USB Settings: Select Setup and press the Enter button. You will have two options, Disable and Enable. Select Enable
to active the USB port. After you select this option on press Enter the DVR will restart. After enabling the port you can
connect the USB 2.0 port on the DVR to a USB 2.0 port on a PC you will be able to back up the files from the hard
drive on the DVR to the hard drive on the PC.
Playback: You will have an icon for the DVR in My Computer on the PC. The PC will find the new hardware and will
put a new drive letter in "My Computer". Open the new drive letter by clicking on the icon to see the files. You can play
the files back using the client program that comes with this DVR through the record info option and local playback.
NOTICE: You will need to backup the entire hard drive from the DVR to the hard drive on the PC before you
will be able to select individual files for playback.
G) Video Spot Settings: When you attach a monitor to the second video out port it will display each of the cameras in
sequence. You can use this option to select the length of time that each camera appears before switching to the next camera.
The options are 5, 10, and 15 seconds.
3.4 Screen Settings
When the system is in the single screen mode you can adjust the picture quality
Brightness: press the analog key on the remote control, the screen will show “Brightness” on the top right hand corner.
Press “–” or “+” to adjust the brightness as desired.
Saturation: Press the “Analog” key for second time and “Saturation” appears on the top right hand corner. Press “–” or “+”
to adjust the saturation as desired.
Contrast: Press the “Analog” key for third time and “Contrast” appears on the top right hand corner. Press “–” or “+” to
adjust the contrast as desired.
Hue: Press the “Analog” key for the fourth time and “Hue” appears on the top right hand corner. Press “–” or “+” to adjust
the color as desired.
Appendix A System Specifications
Monitor
17'' 4:3 TFT/LCD
Video Input
Four Channels Independent Input 1.0Vp-p, 75Ω BNC
Video
Two Channels PAL/NTSC output，1.0Vp-p, 75Ω BNC, Multiple Video Signal
Video Output
One Channel VGA display output
24
QT19D328SC User’s Manual
Video Display
Single picture, built-in quad display
PAL system: 25 frames/second CCIR625 lines 50 fields
NTSC system: 30 frames/second CCIR625 lines 50 fields
Video Standard
Real time recording resources, one or four channels can play backward at the same
System Resources
time；one or four channel monitoring, network real time monitoring
Audio Input
Two channels independent input 600Ω RCA
Audio Output
Two channels independent output
1.0-2.2V
600Ω RCA
Basic Output Gain
Distortion Plus Noise
Recording Solutions
Audio Compression
Operating Language
Operating Interface
Password control
Image Compression
Audio
≤-30dB
Volume and Image are Synchronized
MPEG-1 LAYER2
English
System
OSD (On Screen Display) menu
Password for users and administrators
MPEG-4 Variable bit streams/ Constant bit streams
Built-in quad ：CIF format（352×288 Single picture ： HD1 format （ 704×576
Image format
pixels ）
pixels）
Video code rate
6.25-350Kbyte/s
22.5M-1260Mbyte/hour
6.25-250Kbyte/s
22.5M-900Mbyte/hour
Video volume taken in H.D.
Play backward 352×288 Pixels，real time monitoring 704×576 pixels，VGA output
Resolution
704×576 pixels
Digital
Processing
and Storage
Video current standard
Audio current standard
Audio code rate
ISO14496
ISO11172
24Kbyte/s
Audio volume taken in H.D.
Internal Storage
86.4Mbyte/hour
One IDE hard drive，up to 300GB
8 adjustable levels：1-8 with 1 highest quality
Full duplex
Image quality
Data read and write method
Motion Detection
Alarms
192 detecting areas can be set, and 16 levels adjustable sensitivity
25
QT19D328SC User’s Manual
Four channels alarm in（On/off value）input independently
Open/ close circuit
Alarm input
Alarm Input options
One channel linkage alarm output，one channel power trouble alarm output，one
channel other trouble alarm output
Alarm Output
Relay on/off value：1A 120VAC/24VDC，longtime on/off optional
PTZ Port
RS485
Other Ports
Serial Port
RS232 universal serial interface
RJ-45 10M/100M Ethernet interface
Support TCP/IP
Network Port
Network Transport protocols
Network Transport
Browsing Solutions
Clock
Network
interface
ADSL, ISDN, LAN, CAN
Software included, Internet Explorer
Built-in hard clock and permanent calendar
AC90 ～ 250
Power
Power Consumption
Video System
Max Brightness
Max Contrast
Response Time Tr/Tf
Visual Angle
Max：55W
Universal video system
300cd/m2
Others
450:1
Tr+Tf=（16ms）
170°/150°
Weight
13 lbs (6.0Kg)（Not Including H.D.）
Dimensions
15.25 in x16 in x 121 in (387mm×406mm×121mm)
( W×H×D)
Appendix B Camera Specifications
Model
Image Sensor
Lens
QD28414 & QD28414W
1/4" Sony Super HAD Color CCD
4-QD28414 with 6mm and 4-QD28414W with 3.6mm
420TVL
Horizontal Resolution
26
QT19D328SC User’s Manual
Effective Pixels
Field of View
510x492 NTSC
42° for 6mm, 74° for 3.6mm
BNC (F), 12VDC 2.1mm (F)
0 Lux
Connectors
Minimum Luminance
Infrared LEDs/Distance 12/30ft
IR LED Wavelength
Video Output
850nm
1 Vp-p75 ohm
Electronic Shutter Speed 1/50 (1/60)-1/100,000sec
Audio Output
None
S/N Ratio
>48dB
Gamma Characteristic
Power Supply
0.45
12V DC
Power Consumption
Operating Temperature
Dimensions
120mA (300mA Max with LEDs on) per camera
-4°F to 122°F
2.5(W) x 3.5 (D) x 2.5 (H) in
12 oz (340 g)
Weight
Appendix C Product Service & Warranty
Thank you for choosing our products.
All of our products have a conditional free warranty repair service for hardware within 12 months starting
from purchase date, and a free exchange service within one month (valid for manufacturing defects). Permanent
upgrading service is provided for the software.
Liability Exclusions:
Any product malfunction, abnormalities in operation or damage caused by following reasons are not within
the free service scope of our company. Please select payable service.
27
QT19D328SC User’s Manual
(1) Equipment damage caused by improper operation
(2) Improper environment and conditions in/on which the equipment operates, e.g., improper power, environment
temperature, humidity and lightening strike etc. that cause equipment damage.
(3) Damage caused by acts of nature: earthquake and fire etc.
(4) Equipment damage caused by the maintenance of personnel not authorized by our company.
(5) Product sold over 12 months ago.
In order to provide various services to, please complete registration procedure after you purchase the
product. Cut off or copy Your Information Card and fax or mail it to us after the card is filled in. You can also
If you have questions:
Contact Us:
Mailing Address:
DPS Inc.
8015 E. Crystal Dr
Anaheim, CA 92807
Customer Service:
Phone: 877-998-3440 x 538
Email: [email protected]
Website:
Tech Support:
Fax: 714-998-3509
Phone: 877-998-3440 x 539
Email: [email protected]
28
Customer Information Card
You’s Name
Company Name
Postal Address
Postal code
Phone Number
E-mail
Mr./Mrs.
Model Number
of Product
Serial Number of
Product
Purchase Date
Distributor
The material in this document is the intellectual property of our company.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by
any means without our company’s prior written permission.
1. Our products are under continual improvement and we reserve the right to make changes without notice.
But no guarantee is given as to the correctness of its contents.
2. We do not accept any responsibility for any harm caused by using our product.
3. The product picture may differ from the actual product, which is only for r reference. The accessories will
probably be different according to the different selling areas. For details of accessories, please refer to r local
distributor.
Copyright reserved
|