PYLE Audio VCR PLTVCP85 User Guide

VIDEO CASSETTE RECORDER  
WITH BUILT-IN TV TUNER  
PLTVCP85  
 
SAFETY INSTRUCTIONS  
1. Read Instructions-All the safety and operating instructions should be read before the Video  
Cassette Recorder is operated.  
2. Retain Instructions- The safety and operating instructions should be retained for future reference.  
3. Heed Cautions and Warnings-All cautions and warnings regarding the Video Cassette Recorder  
should be adhered to.  
4. Follow Instructions-All operating instructions should be followed.  
5. Cleaning-Unplug or turn off vehicle power to the Video Cassette Recorder before cleaning.  
Do not use liquid cleaners or aerosol cleaners. Use only a damp cloth for cleaning.  
6. Attachments-Do not use attachments not recommended as they may cause hazards.  
7. Water and Moisture-Do not use this video product near water, for example, near a bath tub,  
kitchen sink, near a swimming pool or other wet locations.  
8. Accessories-Do not place the Video Cassette Recorder on an unstable cart, stand, tripod, bracket,  
or table. The Video Cassette Recorder may fall, causing serious injury to a child or adult,  
and serious damage to the Video Cassette Recorder. Use only with a cart,stand, tripod, bracket,  
or table recommended . When used in vehicles, the Video Cassette Recorder must be securely fastened.  
9. Ventilation-Slots and openings in the cabinet are provided for ventilation to ensure reliable operation  
of the Video Cassette Recorder and to protect it from overheating. These openings must not be  
blocked or covered. The openings should never be blocked by placing the Video Cassette Recorder  
on a bed, sofa, rug, or other similar surface. The Video Cassette Recorder should never be placed  
near or over a radiator or heat register. This video product should not be placed in a built-in installation  
such as a book case or rack unless proper ventilation is provided.  
10. Power Sources-The Video Cassette Recorder should be operated only from the type of power  
source indicated on the marking label. If you are not sure of the type of power supply ,  
consult your appliance dealer or local power company. For video products intended to operate from  
battery power or other sources, refer to the operating instructions.  
11. Do not attempt to service the set yourself as opening or removing covers may expose you to  
dangerous voltage or other hazards.  
Refer all servicing to qualified service personnel.  
2
 
INFORMATION TO THE USER  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates,  
uses and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interfere nice to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by  
one more of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
WARNING  
Changes or modifications not expressly approved by the manufacturer could void the user’s  
authority to operate the equipment.  
TABLE OF CONTENTS  
CAUTIONS AND WARNINGS  
SAFETY INSTRUCTIONS  
TABLE OF CONTENTS  
1
2
3
FEATURES  
4
ACCESSORIES  
4
INSTALLATION WITH MOUNTING BRACKETS  
FRONT PANEL-CONTROLS AND INDICATORS  
REAR PANEL-CONNECTIONS AND POWER  
REMOTE CONTROLLER  
SETTING THE MENU  
5
6
8
10  
11  
13  
14  
14  
15  
17  
OPERATING TV TUNER  
VIDEO HEAD CLEANING  
ERASURE PROTECTION  
TROUBLE SHOOTING  
SPECIFICATIONS  
3
 
FEATURES  
BUILT-IN TV TUNER (TV/CATV)  
HI-FI STEREO SYSTEM  
BACK LIGHTING OF FUNCTION BUTTONS  
ON SCREEN DISPLAY (English)  
EXTERNAL IR REMOTE CONTROLLER WITH RECEIVER  
DEW & HEAT SENSORS FOR TAPE PROTECTION  
NTSC COLOR SYSTEM  
TWO AUDIO/VIDEO INPUTS  
ENCORE FUNCTION  
- Press ENCORE key on the remote controller to watch the desired picture once during playback.  
AUTO REPEAT PLAY  
- This function can be turned on/off from "menu".  
DIGITAL AUTO TRACKING  
- This VCR plays clear pictures without special operations.  
AUTO START FUNCTION  
- This VCR will automatically power on and into PLAYBACK mode when a cassette is inserted.  
DC POWER SUPPLY (2 KINDS OF DC 12V INPUTS)  
ACCESSORIES  
VCR UNIT  
INSTRUCTION MANUAL  
POWER CABLE  
REMOTE CONTROLLER AND BATTERY  
REMOTE IR SENSOR CABLE (5M)  
CONVERT-ADAPTER  
MOUNTING BRACKET AND SCREW  
4
 
INSTALLATION WITH MOUNTING BRACKETS  
Use the short screw for the joint of the VCR and bracket.  
Use the long screw for installation of this VCR to your vehicle or any  
other place.  
The VCR can be mounted vertically , horizontally or at any angle in between with the  
supplied mounting brackets. The VCR cannot be mounted upside down or on its side.  
VCR is sensitive to dirt and other contaminants. Do not mount the unit in direct sunlight  
or where fluids are likely to spill on or in the unit.  
The VCR is for 12Volt negative ground vehicles only.  
5
 
FRONT PANEL-CONTROLS AND INDICATORS  
1
DEW  
/HEAT  
REC  
Hi-Fi  
13  
2
3
4
5
10  
7
6
8
11  
12  
9
1. Cassette Compartment  
The power is on automatically when the cassette is inserted even if the power was  
off. When the cassette is inserted, Auto Tracking Adjustment operates automatically.  
2. Power Key  
When power is supplied to the set, the power indicator lamp will always light up in red.  
The Power ON and Power OFF mode will be toggled by pressing this key.  
When the POWER is switched on, the power lamp will light up in red the other keys will  
light up in green.  
3. Cassette-In Lamp  
When the cassette is inserted, the CST-IN lamp will light up in green.  
4. Eject Key  
Press this button to eject tape.  
5. Stop Key  
Press this button to stop tape.  
6. Rewind / Review Key  
If this key is pressed in the PLAYBACK mode, the VCR enters the reverse picture  
search mode, and "REW" indicator lamp will be blinked.  
If pressed in STOP mode, then the tape will rewind at high speed,  
the indicator lamp will up in red.  
6
 
7. Play / Re-AutoTracking  
Press this key to playback a recorded tape, or to release special operation such as the  
search mode.  
In the playback mode the playback indicator lamp will be light in red, and Auto  
Tracking mode, this indicator lamp will blink.  
When the playback picture is noisy, press this key to operates Re-Auto Tracking.  
8. Fast Forward / Cue Key  
If this key is pressed in the PLAYBACK mode, the VCR enters the forward picture search  
mode, and "FF" indicator lamp will be blinked.  
If pressed in STOP mode, then the tape will fast forward at high speed,  
the indicator lamp will up in red.  
9. REC Key  
Press the REC key for at least one second to start recording.  
10. DEW/HEAT Lamp  
When power is on, this indicator flashes red to indicate excessive moisture buildup inside  
the VCR.  
The unit will not operate unit it dries out sufficiently ( the tape can be ejected from the unit).  
When DEW mode has been activated, leave the unit on the allow it to dry out completely.  
11. Hi-Fi Lamp  
In the Hi-Fi out mode, the lamp will light up in red.  
12. Auto Repeat Lamp  
During Auto repeat operation, Auto Repeat lamp will light up in red.  
13. Audio/Video In Jacks (AV2)  
Connect these jacks to the audio/video out jacks terminal of your game machine or  
camcorder using the RCA cord.  
For displaying this Front A/V lnput connected, Input Signal should be set to " AV2" in  
Menu setting mode.  
7
 
REAR PANEL-CONNECTIONS AND POWER  
6
7
2
3 4  
5
1
1. AUDIO/VIDEO IN (AV1)  
Connector this terminal to VIDEO/AUDIO OUT terminal of your Game machine,  
Camcorder, Portable DVD Player, using the RCA cord  
For displaying this Rear A/V input connected, Input Signal should be set to "AV1"  
in Menu setting mode.  
2. AUDIO/VIDEO OUT  
Connect this terminal to VIDEO/ AUDIO IN terminal of your TV (or Amplifier/Monitor),  
using the RCA cord provided.  
3. IR INPUT  
Connect this terminal to Remote IR Sensor cable provided.  
8
 
4. DC 12V IN JACK (Locking type)  
For car using, we recommend to use this connecter with 3-wire system.  
* Connector description for 4  
ACC 12V  
VEHICLE BATTERY 12V  
GND  
5. DC 12V IN JACK ( Round type)  
To use this connector, below Convert-Adapter accessory should be locked into  
above connector 4.  
( Convert-Adapter)  
* Please note : We highly recommend to connect the unit corresponding to the 3-wire  
system of 4.  
Thus, to make sure a proper working of power-off tape guide. Beyond it,  
the unit will automatically change to standby mode after turning off the  
vehicle in order to save the car battery.  
6. ANT IN (TV/CATV)  
Connect the TV antenna (or cable if available- home use) to this connector.  
7. RF OUT  
This connectors provides an interface to the antenna input connectors terminal of your  
television using a coaxial cable.  
Set TV to channel 3 or 4 to watch video tapes.  
9
 
REMOTE CONTROLLER  
1. To watch the desired picture once more during playback, press "ENCORE" key .  
The VCR unit rewinds the tape for 5 seconds and will play the picture watch again.  
2. POWER ON/OFF  
3. To watch the picture from start position of tape, press "REPLAY" key .  
The VCR unit rewinds the start position of tape.  
4. TRACKING -,+ (Manually Tracking in playback mode) / CHANNEL -,+ ( in TV or CATV mode)  
5. PLAY  
6. FAST FORWARD  
7. SELECT  
8. Tape speed in recording (SP,EP)  
9. SHIFT (Cursor Move)  
10. During the Hi-Fi STEREO tape playback mode, you can select the audio out channel.  
"Hi-Fi  
Hi-Fi "L"  
Hi-Fi "R"  
Mono  
Hi-Fi  
"
11. RECORDING  
12. MENU (setting OSD, System and TV Tuner)  
13. STOP  
14. REWIND  
15. PAUSE/STILL  
16. When the playback picture is noisy, this "RE - TRACKING" key will control the playback picture quality  
automatically.  
17. EJECT  
18. Press to switch between TV and VCR source.  
This switch is functioned only when RF OUT connects to TV antenna Input with setting of the TV channel 3 or 4.  
10  
 
SETTING THE MENU  
Setting the OSD (On Screen Display)  
MENU  
1. Press MENU key on the remote control.  
OSD  
ON  
ON  
ON  
EP  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
2. Press select  
key until the appropriate system is  
VCR OUTPUT CH CH3  
selected. ( "on" or "off" )  
INPUT SIGNAL  
TV  
SHIFT: SEL:  
END:MENU  
3. On completion, press MENU key to exit the menu.  
Setting the Auto PLAY  
1. Press MENU key on the remote control.  
2. Press shift key, until the cursor is placed in front of the  
"AUTO PLAY " option.  
MENU  
OSD  
ON  
ON  
ON  
EP  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
VCR OUTPUT CH CH3  
INPUT SIGNAL CATV  
SHIFT: SEL: END:MENU  
3. Press select  
key until the appropriate system is selected.  
( "on" or "off" )  
4. On completion, press MENU key to exit the menu.  
Setting the Auto Repeat  
1. Press MENU key on the remote control.  
2. Press shift key, until the cursor is placed in front of the  
"AUTO REPEAT " option.  
MENU  
OSD  
ON  
ON  
ON  
EP  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
VCR OUTPUT CH CH3  
INPUT SIGNAL CATV  
SHIFT: SEL: END:MENU  
3. Press select  
key until the appropriate system is selected.  
("on" or "off ")  
4. On completion, press MENU key to exit the menu.  
11  
 
Setting the Record Speed  
MENU  
1. Press MENU key on the remote control.  
OSD  
ON  
ON  
ON  
EP  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
2. Press shift  
key, until the cursor is placed in front of the  
VCR OUTPUT CH CH3  
"RECORD SPEED" option.  
INPUT SIGNAL  
TV  
SHIFT: SEL:  
END:MENU  
3. Press select  
key until the appropriate system is selected.  
("EP" or "SP")  
3. On completion, press MENU key to exit the menu.  
Setting the VCR Output CH  
MENU  
1. Press MENU key on the remote control.  
OSD  
ON  
ON  
ON  
EP  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
2. Press shift  
key, until the cursor is placed in front of the  
VCR OUTPUT CH CH3  
"VCR OUTPUT CH" option.  
INPUT SIGNAL  
TV  
SHIFT: SEL:  
END:MENU  
3. Press select  
key until the appropriate system is selected.  
("CH3" or "CH4")  
3. On completion, press MENU key to exit the menu.  
Setting the Input Signal (Entrance to TV Tuner Operation)  
MENU  
1. Press MENU key on the remote control.  
OSD  
ON  
ON  
ON  
EP  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
2. Press shift  
key, until the cursor is placed in front of the  
VCR OUTPUT CH CH3  
"INPUT SIGNAL" option.  
INPUT SIGNAL  
TV  
SHIFT: SEL:  
END:MENU  
3. Press select  
4. Press shift  
key, then the current input signal mode will be blinked.  
key until the appropriate system is selected.  
"AV1" "AV2" )  
key, to keep selected input signal.  
("TV"  
"CATV"  
5. Press select  
Note :  
AV1 - Rear A/V Input  
AV2 - Front A/V Input  
If " TV" or "CATV" is selected, channels will be found and stored automatically.  
12  
 
OPERATING TV TUNER  
TV CHANNEL SET  
If RF-Signal is not input searching channel will be displayed blue-back picture.  
MENU  
OSD  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
ON  
ON  
ON  
EP  
CH***  
AUTO  
SEARCHING..........  
VCR OUTPUT CH CH3  
INPUT SIGNAL  
SHIFT: SEL:  
TV  
END:MENU  
1. Press MENU key on the remote control.  
2. Press shift  
3. Press select  
4. Press shift  
key, until the cursor is placed in front of the "INPUT SIGNAL" option.  
key, then the current input signal mode will be blinked.  
key, until "TV" is selected.("TV"  
"CATV"  
"AV1"  
"AV2)  
5. Press select key, then channels will be found and stored automatically.  
While the "AUTO SEARCHING " is progressing, channels will be changed up to 69.  
6. When searching and storing is completed, the TV mode will be displayed.  
NOTE :  
While searching and storing channels, no button will be operated.  
When "AUTO REPAT" function is "OFF" and VCR is "STOP" mode, this function will be operated.  
CATV CHANNEL SET  
If RF-Signal is not input searching channel will be displayed blue-back picture.  
MENU  
OSD  
ON  
ON  
ON  
EP  
CH***  
AUTO PLAY  
AUTO REPEAT  
RECORD SPEED  
AUTO  
SEARCHING..........  
VCR OUTPUT CH CH3  
INPUT SIGNAL CATV  
SHIFT: SEL: END:MENU  
1. Press MENU key on the remote control.  
2. Press shift key, until the cursor is placed in front of the "INPUT SIGNAL" option.  
3. Press select key, then the current input signal mode will be blinked.  
4. Press shift key, until "CATV" is selected.("TV" "CATV" "AV1"  
5. Press select key, then channels will be found and stored automatically.  
"AV2)  
While the "AUTO SEARCHING " is progressing, channels will be changed up to 125.  
6. When searching and storing is completed, the CATV mode will be displayed.  
NOTE :  
While searching and storing channels, no button will be operated.  
When "AUTO REPAT" function is "OFF" and VCR is "STOP" mode, this function will be operated.  
13  
 
VIDEO HEAD CLEANING  
The video heads enable the VCR to read video information pictures from the tape during playback.  
In the unlikely event that the heads become clogged with dirt video playback will be impossible.  
This can easily be determined during playback of a known good tape, there is good sound, but the  
picture is extremely snowy.  
If this is the case, have the video cassette recorder checked by qualified service personnel.  
NOTES  
During normal operation of the VCR, the video and audio heads can accumulate dirt over a period  
of time, especially when using an old or poor quality tape. When the heads are dirty, the picture  
can get snowy and the tracking control will have little or no effect.  
If this condition occurs, head cleaning cartridges may take care of the problem and restore normal  
picture.  
We recommend that head cleaning cartridges be used sparingly since they are very abrasive and  
can damage the video heads during prolonged use.  
If the problem is not resolved with the head cleaning cartridge then the unit needs to be checked  
by a qualified service personnel.  
ERASURE PROTECTION  
Video cassettes are equipped with a safety tab to prevent accidental erasure. When the tab is  
removed, recording can not be performed.  
TO PREVENT ACCIDENTAL ERASURE  
- After recording, break off the safety tab with a screwdriver  
if you don't want to record over the tape.  
TO RECORD AGAIN  
- Cover the hold with cellophane tape.  
14  
 
TROUBLE SHOOTING  
Before calling service personnel, check the following points for a possible cause of the trouble.  
A minor adjustment on your part may eliminate the trouble.  
SYMPTOMS  
POSSIBLE SOLUTIONS  
CAUSE  
Check the power cord.  
There is no power  
to the VCR?  
The power cord is not  
connected.  
The polarity of power cord  
is not correct.  
Change the polarity of  
power cord.  
Noise bars on  
screen.  
Tracking is not adjusted.  
Adjust the picture to be clear  
by pressing the Re-tracking.  
Turn off the power and turn on  
the power again by pressing  
the POWER cord. Unplug and  
replug the power cord.  
If the cassette or the VCR  
is not in normal condition,  
every indicator LED/LAMP  
lights up and the VCR does  
not work.  
Operation key does  
not work.  
Cassette is ejected  
upon inserting  
Safety device works to  
protect the cassette when  
it is inserted incorrectly.  
Pull the cassette out (unloading)  
and insert it firmly into the  
cassette compartment.  
The cassette can not be  
playback in Hi-Fi mode.  
Wait for a second.  
The cassette is recorded  
in mono VCR.  
The first auto tracking is  
executing unit now.  
Audio output does  
not change to  
Hi-Fi mode.  
No backlighting at  
power button.  
No 12V DC.  
Check circuit fuse at source of  
power  
(see vehicle/converter manual).  
In-line fuse of power cord  
(in light plug).  
Power cord unplugged from  
12V outlet or at rear of unit.  
15  
 
SYMPTOMS  
POSSIBLE SOLUTIONS  
CAUSE  
(Unit in dew mode) Dew  
feature activated  
(see instruction manual)  
Retain power to recorder and  
allow unit for a time to get rid  
of moisture.  
Power indicated with  
backlighting-unit will  
not operate.  
(After 30 minutes if dew  
indicator is still on, completely  
switch power off from unit and  
resupply after a minute. This  
can reset dew indicator if  
moisture eliminated.)  
No tape in unit.  
Low voltage.  
Insert the tape.  
Start the vehicle, if not running.  
Poor video/snow  
picture or line on  
screen.  
Clean head using tape cartride  
cleaner.  
Dirty heads.  
VCR connected to A/V Input  
jack, RCA patch cables  
set in TV mode.  
Switch TV to video mode with  
remote control or switch behind  
control door of TV.  
PLAY mode indicated  
no audio or video  
to TV.  
VCR connected to A/V  
output jacks.  
Change connections from A/V  
out to A/V input.  
Poor connection between  
VCR output and TV input.  
Check connection.  
Reversed A/V inputs to TV.  
Check connection.  
16  
 
SPECIFICATIONS  
MODEL  
PLTVCP85  
POWER SUPPLY  
POWER CONSUMPTION  
DIMENSION  
DC 12V  
13W  
265 X 91 X 275 (W xH x D)mm  
WEIGHT APPROX  
VIDEO SIGNAL SYSTEM  
TAPE TYPE  
2.9Kg  
NTSC color  
VHS Type  
TAPE SPEED  
SP: 33.35 mm/sec,  
LP: 22.23mm/sec, SLP: 11.12 mm/sec  
Antenna In/Output terminnals  
FF/REW TIME(T-120)  
UHF/VHF 75 F type connector.  
Approx. 5min  
VIDEO SIGNAL INPUT  
AUDIO SIGNAL INTPUT  
Video In terminal (RCA) 1.0 Vp - p  
Audio In terminal (RCA),47K ohm  
VIDEO SIGNAL OUTPUT (LINE)  
AUDIO SIGNAL OUTPUT(LINE)  
OPERATING CONDITION HUMIDITY  
1.0Vp-p, 75 ohm unbalanced, NEGATIVE SYNC  
-6dBm  
80 RH (MAX).  
Temperature : 5  
~ 35  
(41 ~ 95  
)
OPERATING POWER VOLTAGE  
12 ~ 14V  
Desing and specifications are subjected to change without notice.  
17  
 

Radio Shack Automobile Battery Charger 12 493 User Guide
RBH Sound Speaker WM 24 User Guide
RedMax Blower HB280 User Guide
RF Link Technology Baby Monitor ABM 4161 User Guide
Ruckus Wireless Network Card MF2501 User Guide
Ryobi Blower RY42110 User Guide
Samsung Computer Monitor 20080310201909625 User Guide
Sanyo Digital Camera VPC X1200 User Guide
SBC comm Conference Phone LI900SBC User Guide
Sears Air Conditioner 66162392 User Guide