Limited Warranty
P T - 2 4 0 0
A m p l i f i e r
All PYLE PRO products are carefully constructed and tested before
shipment. Units purchased in the USA are warranted to be free of
defects in material and workmanship for two (2) years from the date
of purchase. This warranty is limited to the original retail purchaser
of the amplifier.
Should the unit fail due to factory defects in material or workmanship,
your unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return
Hotline at (718) 236-6948 to obtain a Return Authorization Number.
This R.A. # must appear on the outside of your package and on all
paperwork relating to your return.
When returning the unit to us for warranty service, it must be carefully
packed and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
P T - 2 8 0 0
A m p l i f i e r
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing
with the product
• Include in your letter your return address, daytime phone
number and R.A. number
• Also include a check or money order for $15.00 for return
shipping, handling and insurance, or provide your Visa/MC
number with expiration date.
Our obligation under this warranty is limited to the repair or replacement
of the defective unit when it is returned to us prepaid. This warranty
will be considered void if the unit was tampered with, improperly
serviced or subject to misuse, neglect or accidental damage.
Owner’s Manual
INSTALLATION GUIDELINES
Stereo or Mono Inputs
Bridge Mode Operation
Using the power meter
Your Pyle Pro amplifier can be operated in Stereo or Mono
mode, depending on the input source. If the input signal
is mono, connect the source via the LEFT input only (also
marked "MONO" on the back of amplifier). Then slide the
STEREO/MONO selector switch to MONO and the signal will
be routed through both channels.
This amplifier can be operated in mono bridged output
mode, if your speakers can handle the following power
output levels:
The meter LED dispaly position indicate the amplifier output
power.
Connecting the GND (GROUND) screw terminal Connecting
a mixer or preamplifier may cause excessive noise or hum
in the amplifier output. To prevent this, connect one end
of a low-capacitance shield wire to the amplifier's ground
screw (on the rear panel). Then connect the other end of
this wire to the ground terminal on the mixer or preamplifier
enclosure.
Using the left and right Output Level controls
Rotate output level gain clockwise to increase, or
counterclockwise to decrease the output power. To get the
best performance with the leaset sound distortion, always
adjust the output level gain so the meter's level indication
does not continuously exceed to the extreme right.
PT2800: 370 watts
PT2400: 230 watts
As shown in the diagram below, connect the speaker's
positive (+) to the amplifier's red speakers left (A/B) terminals
and negative (-) to red speakers right (A/B) terminals.
CAUTION:It is possible to overdrive the amplifier by
setting output level gain too high, which may cause
damage or failure.
The speaker righr (+) on the amplifier is used a negative
(-) terminal for a bridged connection.
NOTE: IT IS SUGGESTED TO USE A 8-OHM SPEAKER FOR
THE ONE CHANNEL BRIDGE HOOKUP. IF YOU CONNECT
TWO CHANNELS' BRIDGE HOOKUP, PLEASE MAKE SURE
THE SPEAKER IMPEDANCE MUST BE 8-OHM MINIMUM.
MONO SIGNAL SOURCE
About the internal clip circuitry
EQ OR MIXER
Special clip circuitry incorporated into your amplifier's
design protects the amplifier and speaker system from being
damaged from overdriving power.
LOW CAPACITANCE SHIELD WIRE
STEREO/MONO SWITCH IN
"MONO" POSITION
GROUND SCREW
BRIDGED SPEAKER
HOOKUP
Under normal conditions, the amplifier's clip indicator will
flicker as the output power momentarily exceeds the level
as set by the output level gain selector.
STEREO/MONO SWITCH IN
"MONO" POSITION
Input connections
Speaker connections
These amplifiers accept a board range of input sources,
including Compact Disc (CD) players; Cassette, Reel-to-Reel
or other tape players; Radio Tuners; Equalizers; Signal
Processors.
You can connect 4 Ohm, 8 Ohm, or 16 Ohm speakers to
Channel A and/or Channel B of the amplifier. If you connect
two pairs of speakers, be sure to follow these guidelines:
However, under excessive output conditions, the clip
indicator lights remain on continuously, altering you that
the special clip circuitry has become active. When this
occurs, you should simply reduce the output power level
by rotating the Master Volume control counterclockwise.
• Speakers which are connected to the same channel are
part of a pair, and must be of the same impedance.
Connecting a CD or tape player, or tuner
In a normal installation, one would use the RCA JACKS for
connecting a CD player, tape player or tuner.
Using the A/B Speaker Selector Switch
You can listen to speakers on set A or set B individually or
• Speakers connected to different channels are NOT part
of a pair, and can be of different impedances.
simultaneously. Simply push in or out the desired speaker
set to make your selection.
1. Prepare the speaker wire by removing about 1 inch of
insulation from the end of speaker wire you intend to
connect to the amplifier. Then twist the exposed wire to
secure all the wire strands.
Using headphones
To listen privately, or to monitor sound sources, connect
a pair of low impedance stereo headphones (not supplied)
with 6.35mm plug into the PHONES jack on the amplifier
front panel.
CAUTION:If the impedance of your speakers is 4 OHMS, do
not use both
the speaker A and speaker B terminal at the same time as
the net
use RCA jacks
NOTE: Use 18-gauge speaker wire for lengths up to 25
feet; 16-gauge wire for lengths over 25 feet. It is
recommended that you use the shortest length of wire
possible.
CD PLAYER, TAPE PLAYER
OR TUNER
impedance may be low enough to damage your amplifier.
Please listen safely. Follow these recommendations:
Caring for your Pyle Pro Amplifier
Do not listen at extremely high volume levels. Extended,
high-volume listening can lead to permanent hearing loss.
Your Pyle Pro Amplifier is an example of superior design
and craftsmanship. The following suggestions will help you
care for your amplifier so you can enjoy years of use:
• Keep the amplifier dry. If it gets wet, wipe immediately.
• Use the amplifier only in well-ventilated installations.
• Handle the amplifier away from dust and dirt.
• Wipe occasionally with a damp cloth to keep it looking
new.
2. Connect the speaker wire to the speaker's positive and
negative terminals.
Always start with the volume control set to a LOW level
BEFORE you put the headphones on. Then gradually increase
the voulume as necessary.
NOTE: Most speaker terminals are either color-coded
or have a mark that indicates the terminal's polarity.
Usually positive terminals are red or have a plus symbol
(+), and negative terminals are black or have a minus
symbol (-).
Connecting an equalizer or external signal processor
Connect the processor's OUT to the amplifier's IN connector.
Connecting to standard AC power
Do not use harsh chemical, solvents or detergents!
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
EQ OR MIXER
3. Connect the speaker wires to the amplifier's left and
right speaker terminals according to the terminal color
polarity.
Replacing a fuse
This amplifier requires a fuse with the proper rating for
protection from power surges and short circuits. If the
amplifier suddenly turns off or will not turn on, the fuse
is properly blown.
Mounting the amplifier
This amplifier is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
use XLR/6.35mm combo jacks
R
L
4 OHMS
MIN. IMPEDANCE
Remove the old fuse and replace it with an identical,
serviceable fuse:
PT-2800 = 7A (110-120V) OR 3.5A (220-240V)
PT-2400 = 5A (110-120V) OR 2.5A (220-240V)
SPEAKER MUST BE OF
SAME IMPEDANCE.
Tightly secure four mounting screws (not supplied) through
these four slots and into your standard electronics equipment
rack.
use RCA jacks
EQ OR MIXER
CAUTION:Never use a fuse with a higher rating.
Turning the amplifier on
1.Turn on the audio input source equipment which is
connected to the amplifier INPUT jack.
CONNECTIONS USING SPEAKER TERMINALS
2.Set the amplifier's left and right output level gain controls
to the minimum level settings.
3.Press the power switch to turn the amplifier on.
2 – PYLE PRO PT-2400/2800 Amplifier Owner’s Manual
PYLE PRO PT-2400/2800 Amplifier Owner’s Manual - 3
Amplifier Specifications
PT-2800
PT-2400
Input Impedance
20 k-Ohms
20 k-Ohms
Continuous Output Power
Stereo Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
125W x 2
190W x 2
500W x 2
1000W x 2
80W x 2
120W x 2
300W x 2
600W x 2
Maximum Power, 8 Ohms
Maximum Power, 4 Ohms
Bridged Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
320W x 1
370W x 1
1000W x 1
2000W x 1
180W x 1
230W x 1
600W x 1
1200W x 1
Maximum Power, 8 Ohms
Maximum Power, 4 Ohms
THD at rated output power
0.1%
10 Hz to 50 kHz
0.775V
0.1%
10 Hz to 50 kHz
0.775V
Frequency Response +/– 3 dB
Input Sensitivity for rated output power
Signal-to-Noise Ratio A-Weighted
90 dB
90 dB
Speaker Impedance
A or B only
A plus B
4-16 Ohms
8-16 Ohms
8-16 Ohms
4-16 Ohms
8-16 Ohms
8-16 Ohms
Bridged Mode
Power Requirement
120 VAC, 60 Hz/240 VAC, 50 Hz
120 VAC, 60 Hz/240 VAC, 50 Hz
Power Fuse
110-120V AC
220-240V AC
7A
3.5A
5A
2.5A
Dimensions H x W x D, inches
(mm)
3 15/32 x 19 x 10 5/8
(88 x 482 x 269)
3 15/32 x 19 x 10 5/8
(88 x 482 x 269)
Weight, lbs (kg)
9.3 Kg
(20.46 lb)
8.5 Kg
(18.7 lb)
4 – PYLE PRO PT-2400/2800 Amplifier Owner’s Manual
PYLE PRO PT-2400/2800 Amplifier Owner’s Manual - 5
|