,
INSTALLATION INSTRUCTIONS / OWNER S MANUAL
PCD970R
AM/FM HIGH POWER FLIP DOWN DETACHABLE FACE
CD PLAYER
SAFETY PRECAUTIONS
.
Secure the CD player
When installing your CD player in the vehicle, make sure it is mounted properly in the dash,
using an after market installation kit if needed. When using the supplied mounting sleeve,
it is a must that you also use the supplied back brace to support the back of the CD
player.
Use caution when mounting the CD player.
Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment
wires. Make sure you know where they are when mounting the CD player to avoid puncturing
lines, and shorting wires.
Use high grade wire connectors.
To ensure maximum power transfer and secure safe connections, it is recommended to use
high grade barrel or crimp cap connectors.
Do not run any wires underneath the vehicle.
Exposed wires can be cut or damaged. It is best to run all wires through the vehicle under the
carpet and/or side panels. This enables to a cleaner installation and less risk of damage.
Run signal wires away from electrical wires
To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or
engine noise), run signal wires away from the car's electrical wiring.
Make all ground wires as short as possible and terminated at the same point.
In order to reduce the chance of ground loops (i.e. engine noise), make the grounded wire as
short as possible to reduce the wire's resistance. Also, when using multiple components, make
sure all units are grounded at the same point.
Avoid sharp edges when running the wires.
To avoid the possibility of power, signal or speaker shorts, be careful not to allow the amplifier
wires to come in contact with sharp edges. Use a grommet to protect the wire when running
through the fire wall .
2
PCD970R
CARE AND MAINTENANCE
Cleaning the CD player
When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only
the exterior surface of the unit with a dry, clean soft towel using no chemical solvents.
Operating in extreme temperatures
Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case,
wait until the temperature in the vehicle is normal, then resume operation.
Protect your CDs.
When not using the disc player, it is recommended that you remove the CD.
Do not leave an ejected disc sitting on the edge of the disc player for long periods of time.
The disc will warp under direct sunlight. Always put each disc in its case to protect them
during times of non-use.
CD operation.
Never attempt to force anything other than a compact disc in the disc slot. This disc player
is a precision instrument that could be damaged by a foreign object.
Disc skip
When driving down a very rough road, the disc may skip. This will not scratch or damage the disc.
Removing and protecting detachable face plate.
The face plate of the unit may be removed as a theft deterrent. After removing the face
plate, use the case provided to keep the face plate from getting damaged.
PROTECTIVE CASE
FACE PLATE
OPEN BUTTON
( FIG.1)
FACE PLATE
( FIG.2)
Press the OPEN button to flip down the face plate (Fig 1). Then slightly push the face plate
towards the left side before pulling it out from the unit (Fig.2)
Store the face plate in the protective case provided for safe keeping (Fig.3).
3
DISC CARE AND PLAY:
Before playing, clean the disc with a clean, lint-free cloth.
Wipe the disc in the direction of the arrow.
Do not use solvents such as benzine or thinners. Commercially available
cleaners or anti static spray will damage the unit.
Insert a disc with the labeled surface up.
Label
surface up
Do not try to insert another disc when one has already been inserted.
Doing so may damage the unit.
Handle the disc by its edge to keep the disc clean and do not touch
the surface.
Do not stick paper or tape on the disc.
Do not expose the disc to direct sunlight which can cause the disc to warp.
Always store the disc in its case for protection. Scratched up discs will
produce poor sound performance and cause CD player to skip.
4
PCD970R
ELECTRICAL AND SIGNAL CONNECTIONS
Before making the following connections, take time to look over the vehicle's wiring and
determine the location and wires you will be connecting to. If you do not wish to cut or tap
into the vehicles existing factory wiring, there are wiring kits available at your car audio
retailer that will allow you to plug directly into the factory wiring harness. Make sure to
test all wires before connecting to the CD Player.
!
Connect Black wire to chassis ground.
!
!
Connect the Yellow memory backup wire to a Constant +12 Volt power source wire.
Connect the Red ignition wire to a switched +12 Volt power source wire. (The power
wire that is energized when the key is in the accessory position).
!
The blue wire is connected only if a power antenna or an amplifier is used in the
system. This wire supplies +12 Volt output when the CD Player is turned on,
which activates most power antenna relays or amplifier turn on circuits.
FOUR SPEAKER SYSTEM
ANTENNA CONNECTOR
Low level signal output for
AUX RCA INPUT
R
R CH RED
connection to amplifier or
BROWN
L
L CH WHITE
signal processors.
MEMORY +12V
YELLOW
15A Fuse
+
-
FRONT RCA OUTPUT
BLACK(GND)
BATTERY
+12V
FILTER
BOX
R
L
R CH RED
BLACK
REAR RCA OUTPUT
GRAY
L CH WHITE
RED (B+)
R
L
0.5A Fuse
R CH RED
SWITCHED +12V
(ON WITH IGNITION)
BLUE AUTO ANTENNA
+
0.5 A
L CH WHITE
FUSE
+
GRAY
WHITE
FRONT RIGHT
SPEAKER
FRONT LEFT
SPEAKER
GRAY/BLACK
VIOLET
WHITE/BLACK
GREEN
+
+
REAR LEFT
REAR RIGHT
SPEAKER
SPEAKER
VIOLET/BLACK
GREEN/BLACK
5
TWO SPEAKER SYSTEM
ANTENNA CONNECTOR
AUX RCA INPUT
R
Low level signal output for
connection to amplifier or
signal processors.
R CH RED
BROWN
YELLOW
L
L CH WHITE
MEMORY +12V
15A Fuse
BLACK(GND)
+
-
FRONT RCA OUTPUT
FILTER
BOX
BATTERY
+12V
R
L
R CH RED
BLACK
REAR RCA OUTPUT
GRAY
L CH WHITE
R CH RED
RED (B+)
R
L
0.5A Fuse
0.5 A
SWITCHED +12V
L CH WHITE
(ON WITH IGNITION)
BLUE AUTO ANTENNA
FUSE
+
+
GRAY
WHITE
FRONT LEFT
FRONT RIGHT
SPEAKER
SPEAKER
GRAY/BLACK
NOT USED
NOT USED
WHITE/BLACK
NOT USED
NOT USED
CAUTION! Tape unused wires so they do not short against other wires or
chassis ground.
6
PCD970R
MOUNTING THE CD PLAYER
There are two different ways to mount the CD Player. In most Japanese vehicles you can
use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle
does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve
and rear support bracket. When considering your mounting location, make sure the unit will
be leveled. If you cannot mount the CD Player level, due to your vehicles design, make sure
there is no more than a 30 degree tilt. Keeping this in mind will assure proper CD play and
overall reliability.
DIN SLEEVE MOUNTING
Insert the mounting sleeve into a
standard DIN cutout in the dash
kit, dashboard or Console.
Bend the mounting tabs of the sleeve
with a screwdriver to secure the bracke
firmly in place.
Insert the CD Player in the
mounting sleeve until it locks.
7
Attach the back brace to the CD
player using the supplied hardware.
Then attach the other end of the
brace to a firm mounting surface
(i.e. Dash brace, fire wall, e.t.c.)
This will brace the back of the CD
player to ensure solid mounting to
prevent theft and provide optimal
CD play.
Once the CD player is secured, fit the trim
ring over outside edge of the radio until it
snaps into place.
To Attach the Face Plate:
Basically, the face plate should be attached
to the unit in the reverse order of removal.
1 Hold the right side of the plate with the
plate facing down.
First attach the left side of the plate to the
unit by inserting the hole into the left holder.
2 Then slightly push the plate to the left
before attaching the right side hole into the
right holder.
3 Finally push up the face plate until click sound is heard.
8
PCD970R
ISO/DIN MOUNTING
If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on
the side of the CD player to attach to the existing factory mounting bracket, without using
the provided DIN sleeve.
!
!
Remove the factory ISO/DIN mounting bracket from the car along with the factory radio.
Remove the factory radio from the bracket by unscrewing the two Phillips screws on each
side of the radio paying close attention to their screw positions and saving the screws to
mount the CD player.
!
!
Remove the two spring clips from each side of the CD player by removing the screws.
These clips are not used in ISO/DIN mounting method and must be removed to expose the
ISO/DIN mounting holes.
Also remove the detachable face and rectangular trim ring from the CD player and mount
the CD player to the factory ISO/DIN bracket using the screws that you removed from
the factory radio.
! Connect the wire harness and antenna plug to the back of the CD player. Then mount the
factory ISO-DIN bracket to the car.
Note: It is not necessary to attach the outer rectangular trim ring for ISO/DIN mounting
method.
REMOVING THE CD PLAYER
!
!
To remove the CD player from an ISO/DIN mount, follow the above mounting procedure
in reverse order.
To remove the CD player from a sleeve mount, use the pair of keys provided.
Remove the rectangular trim ring by
applying pressure with your finger
tips, then gently pull out away from
the dash.
PLACE FINGER TIPS HERE
Insert the provided removal key into the opening on each side of the CD player.
Push the keys inward until they snap in place. Firmly grab the keys and slowly
pull the CD player out away from the dash.
9
LOCATION AND FUNCTION OF CONTROLS
10
PCD970R
1 POWER
To turn ON the unit, press any button except the OPEN button.
To turn OFF the unit, press the PWR button for more than 2 seconds.
2 FLIP DOWN PANEL
Press the OPEN button to flip down the face plate. This will allow you to insert
or eject a CD and also remove the face plate.
3 CD PLAY
To play a CD, press the OPEN button to flip down the face plate exposing the CD
inserting slot. Gently insert the CD into the slot with the label side facing up. The
disc will automatically be loaded into the unit and start playing the first track of
the disc. The digital display will indicate the track number.
4 EJECT CD
To remove a CD once inserted, press the OPEN button to flip down the face plate
and press the ( ) button located on the left hand side of the CD inserting slot.
Once the CD is ejected, the unit switches to radio mode.
5 VOLUME UP/DOWN
,
Rotate the VOL knob in clockwise direction to raise the system svolume
,
and in counterclockwise direction to lower the systems volume.
Note: For remotecontrol, press the button to raise the volume and press
+
the button to lower the volume.
-
6 MODE
Press the MODbutton to changeamong tuner (radio), CD (if disc is loaded),
and auxiliary input playing mode.
Radio
CD
AUX.
7 BAND
Under radio mode press the BND button to change between three FM bands and
two AM bands.
FM 1
FM 2
F M 3
AM 1
AM 2
11
8
9 RADIO TUNE & CD TRACK UP/DOWN, CD FAST FORWARD/REWIND
I
I
change the frequencynumber up ordown one step. Under SEEK 1mode, press and
Under radio mode, press the
8 or
9 button momentarily and repeatedlyto
I
hold the
8 or I 9 button for more than2 seconds to seek to the next or previous
8 or 9 button to speedily
clear station. UnderSEEK 2 mode, press and holdthe
I
I
change stations upor down. Changingstations will stop once the buttonis released.
(Please refer to SEEK on page 13 on how to set the seek mode between SEEK 1
and SEEK 2.)
In CD playmode, press the
I
8 or I 9 button to move to the nextor previous track.
In CD playmode, press andhold the
I
8 or I 9 buttonto fast forwardor fast
reverse through thesong. The CDresumes playing whenthe button is released.
10 PRESET STATIONS
There are 6 numbered buttons to store into memory and recall stations for each
band. Select a band (if needed) as explained in 7 . Tune to a radio station that
you wish to store. Select, press, and hold a preset numbered button for 2 seconds
until you hear a beep indicating that the station has been stored in memory. To
recall a preset station, simply push the numbered preset button.
11 FUNCTION SELECT
SEL button allows you to display different functions for adjustments. Press the
SEL button momentarily and repeatedly to move the display from Volume, Bass,
Treble, Balance, and Fader functions. Use the VOL knob 5 to adjust the selected
mode. When the mode has not been adjusted for several seconds, display and mode
returns to normal radio or CD operation.
VOL
BAS
TRE
BAL
FAD
(Volume) (Bass)
(Treble) (Balance) (Fader)
VOLUME - Press the SEL button once. Adjust the volume level using the VOL knob
5 .
BASS - Pressthe SEL button twice. Adjust the bass level using the VOL knob 5 .
TREBLE - Pressthe SEL button three times. Adjust the treble level using the VOL
knob 5 .
BALANCE - Pressthe SEL button four times. Adjust the sound balancebetween
left and right speakers using theVOL knob 5 .
FADER - Pressthe SEL button five times. Adjust the sound balancebetween front
and rear speakersusing the VOL knob 5 .
12
PCD970R
Press the SELbutton for more than 2 secondsto display additional set of functions
for adjustments, such as DSP, BeepOn/Off, Seek 1 or 2 , Clock 12 or24, and
Volume Last/Adjust.
DSP - Theunit is equipped with 4 preset equalization modes. Press the SEL button
for more than2 seconds to display DSP OFF. Then turn the VOL knob 5 in
,
the clockwise direction to choose oneof 4 following preset EQ s in the
following order.
When using presetEQ modes youwill not have access to Bassand Treble
settings.
DSP OFF
FLAT
CLASSIC
ROCK
POP
BEEP - Thebeep sound whenyou press abutton on the unit can beturned on or
off. Press theSEL button for more than 2seconds to display the DSP
function. Press theSEL button again momentarily to displayBEEP ON/OFF.
Then use the VOL knob 5 to turn on/offthe beep sound.
SEEK- The unitis equipped with two types of seeks, SEEK 1and SEEK 2, for radio
stations. Press theSEL button for more than 2seconds to displaythe DSP
function. Press theSEL button twice momentarily to displaySEEK 1 or2.
Then use theVOL knob 5 to switch between SEEK 1 andSEEK 2. (This
adjustment is only available during radio operation)
SEEK 1 mode:Pressing
9 button for more than 2seconds will seek
I 8 or
I
up or downto the next strong station duringradio operation.
SEEK 2 mode:Pressing 9 button continuously will speedily change
I 8 or
I
station up ordown until the button is released.
CLOCK- The unitis equipped with two types of clock formats, 12 hour and 24 hour.
Press the SELbutton for more than 2 secondsto display the DSP function.
Press the SELbutton three times momentarily to displayCLOCK 12 or24.
Then use theVOL knob 5 to choose between12 and 24 .
SET VOL -A certain volumelevel can be set to comeon when theunit is turned
on or canbe set to come on atthe same lastlevel before the unit was
turned off. Pressthe SEL button for more than2 seconds to display
the DSP function. Press the SELbutton four times momentarily to
display VOL LAST/ADJ. Use the VOL knob
5
to choose between
VOL LAST andVOL ADJ. Toset the volume to a certainlevel, press the
SEL button momentarilywhen VOL ADJis displayed. Then use the VOL
knob
5
to adjust to certain volume level when A-VOL is displayed.
13
12 CD TOP/PAUSE
In CD playmode, press the TOP
resume normal play.
12 button to pause CD play. Press again to
12 button for more than 2 seconds to go back
In CD playmode, press the TOP
to the top of the disc and play the first track.
13 CD SCAN
In CD play mode, press the INT 13 button to turn on intro playing first 10 seconds
of each track. When wish to listen to the whole track during intro mode,
press the button again to turn off intro.
14 REPEAT PLAY
In CD play mode, press the RPT 14 button to continuously playing the current
track. Press it again to cancel the repeat feature.
15 RANDOM PLAY
In CD playmode, press theRDM 15 button to play alltracks of the disc in random
sequence. Press itagain to cancelrandom play.
16 AUTOMATIC STORING & PRESET SCANNING
In radio mode, press and holdthe APS 16 button for morethan 2 secondsto
activate the automaticstoring function. Onceactivated, the radiostarts search-
ing for first6 strong signaledstations and storesthem into thepreset memory.
After completion, theradio will tuneback to thefirst preset memorystation.
In radio mode, press the APS 16 button formomentarily to activatethe preset
scanning function. Onceactivated, the radiostarts scanning allpreset memory
stations for fewseconds at atime while thepreset memory numberflashes on
the LCD. Pressingthe button againwill stop thescan.
17 MUTE
Press the MUbutton to silence the system. Pressa second time to resume
listening.
18 LOUDNESS
Press the LOUD button once to enhance the bass effect.
Press again to cancel the loudness effect.
19 MONO/STEREO
,
Monaural (Mono) orStereo mode canbe selected for FM tuner sreception. For
best quality sound, stereo mode should be selected. However, Mono mode canbe
selected to help the reception of distant radio stations. Press the STbutton to
select between Mono and Stereo modes.
14
PCD970R
20 CLOCK
Press the CLK button to display the time on the LCD for 5 seconds. To adjust the
time, press and hold the CLK button until the hour flashes and use the VOL 5
knob to adjust the hour. Press and hold the CLK button again until the minute
flashes and use the VOL 5 knob to adjust the minute.
21 RADIO SCAN (Only from Remote)
Pressing the SCN button from the remote control, the unit will scan and search
for the next strong station while playing each station for 5 seconds with station
number flashing. Pressing the SCN button again will stop the radio scan.
22 LOCAL/DX
This button is used to control the sensitivity of the FM radio tuner while searching
for a station. When the radio is powered on, the local mode is off by default. Press
the LOC button to turn on the local mode only to receive the strongest stations.
23 INFRARED REMOTE CONTROL SENSOR
24 SECURITY LED
Designed as atheft deterrent, the red LED will flash when theunit is turned off
and face plateremoved.
25 RESET
The reset buttonshould be pressed when installation is complete and alsowhen
all buttons do not operate.
15
MAINTENANCE OF REMOTE CONTROL
Before using the remote control, the insulating patch must be removed. This
patch was installed to insulate the battery from draining until ready to use.
BATTERY INFORMATION:
Lithium Battery: CR2025 3V
Battery Life: Approximately 6 months.
Replacing the Battery from the Remote Control:
1) Turn over the remote control so the rear side of the remote is facing up.
2) Remove the battery holder by pressing the locking tab with your thumb
and pulling it out.
3) Replace the battery with the same type and the
+
4) Gently push in the holder until securely locked into place.
side facing up.
WARNING:
Do not recharge, disassemble or dispose of in fire.
Battery leakage may cause damage to the unit.
To avoid the risk of accident, keep batteries out of reach of children.
PCD970R
16
TROUBLE SHOOTING THE SYSTEM
The following chart will help in solving most problems that may occur. Should any problem
persist after you have made these checks, please consult your nearest Profile retailer.
Before going through this check list, refer back to the wiring and operating procedures.
ERROR CODES
E 1~ E 10
The unit cannot be operated because of trouble. Press the "RESET"
button
button
. If theindicator still appears afterpressing the"RESET"
, your unit needs repair. Please refer to the warranty section
25
25
of this manual for details on getting the unit serviced.
.
SYMPTOM
No Power
CAUSE
SOLUTION
25
New installation.
Press the RESET
button.
The vehicle's ignition switch Turn the ignition switch to the accessory
is not on.
position. If there is still no power, check the
fuses at the vehicle's fuse block or the
radio's fuse leads.
The fuse is blown.
Replace the fuse with another fuse of the
same recommended value
Remove the disc in the player, then put in
the new one.
Disc cannot There is a disc already in
be loaded or the player.
ejected.
You are trying to put the
Insert the compact disc with the label facing
compact disc in upside down. up.
The compact disc is
extremely dirty or
defective.
Clean the compact disc with a compact disc
cleaning solution or replace the defective
compact disc.
The temperature in the car Cool the inside of the vehicle, then try again.
is too hot.
Condensation build-up on the Leave the disc player off and turn the
inside of the unit.
vehicle's air conditioner on to remove the
condensation build-up inside the unit.
No sound.
The volume control is all the Adjust the volume control.
way down.
The speakers are bad.
Test the speakers to determine if they need
replacing.
The function The built-in microprocessor Remove the disc, then re-insert it. Press the
25
buttons do
not work.
is operating incorrectly.
reset button
.
17
SYMPTOM
CAUSE
SOLUTION
Adjust the angle of the unit to less than 30
degrees
The compact The installation angle is
disc skips.
greater than 30 degrees
The disc player is installed Check to see if the unit is fastened securely
incorrectly
with the back brace supporting the rear of
the unit.
The compact disc is
Clean the compact disc with a compact disc
extremely dirty or defective cleaning solution or replace the defective
disc. compact disc.
Condensation build-up on the Leave the disc player off and turn the
inside of the unit.
vehicle's air conditioner on to remove the
condensation build-up inside the unit.
Check the antenna and connection to insure
The radio
does not
work. The
Radio station
automatic
selection
does not
work.
The antenna is not
connected or the antenna is proper performance.
bad.
The signals in your listening Select stations manually and make sure the
area are weak.
tuner is in the distant stereo mode.
PCD970R
18
SPECIFICATIONS
GENERAL
Power Supply Requirements...........................................DC 12 Volts, Negative Ground
Chassis Dimensions ...............................................................7|| (W) x 6 1/2|| (D) x 2|| (H)
Tone Controls...........................................................................................................................
Bass @ 100Hz..........................................................................................+10dB / -10 dB
Treble @ 10Khz.......................................................................................+10dB / -10 dB
Equalizer..................................................................................................................4 Presets
Maximum Output Power.........................................................................................50W x 4
RMS Output Power..................................................................................................30W x 4
Maximum Current Consumption........................................................................15 Ampere
Fuses
Memory (Constant)........................................................................................15 Ampere
Accessory (Switched).................................................................................0.5 Ampere
RCA line out voltage.....................................................................................................3.7 V
CD PLAYER
Signal to Noise Ratio...................................................................................................>85dB
Channel Separation......................................................................................................>80dB
Frequency Response........................................................................................5Hz ~ 20Khz
Usable Disc....................................................................................CD/CD-R/CD-RW Discs
RADIO
FM
Frequency Coverage.....................................................................87.5 to 107.9MHz(US)
IF................................................................................................................................10.7MHz
Station Presets...................................................................................................................18
AM
Frequency Coverage........................................................................530 to 1710KHz(US)
IF.................................................................................................................................450KHz
Station Presets...................................................................................................................12
Due to continuing product improvement, specifications subject to change without notice.
19
LIMITED WARRANTY
Profile Consumer Electronics, Inc. warrants this product to be free from defects in
material and workmanship for a period of One (1) Year from the date of sale to the
original consumer purchaser. If this product is proven to be defective within this one
year period, Profile will repair it when said product is returned, with a copy of the
dated sales receipt, freight prepaid to Profile.
This warranty is valid only in the United States. This warranty does not cover any
expense incurred in the removal and/or re-installation of this product. This warranty
does not cover any Profile product damaged by accident, misuse, abuse, improper line
voltage, fire, water, lightning, or other acts of God. This warranty is void if any parts
and/or service is/are furnished by anyone other than Profile. This warranty is void if
the factory applied serial number is altered or removed from the product.
This warranty does not cover cartons, cases, batteries, broken or marred cabinets,
magnetic tapes, or any other accessories used in connection with this product or
consequential damages due to a defect in the product.
Any implied warranties, including fitness for use and merchantability, are limited in
duration to the period of the express warranty set forth above. No person is
authorized to assume for Profile any other liability in connection with the sale of the
product. Profile expressly disclaims liability for incidental and consequential
damages that might be caused by this product. The remedies provided under this
warranty are exclusive and lieu of all others.
This warranty gives you specific legal rights. You may have other rights which vary
from state to state or province to province. Some states or provinces do not allow
limitation on how long warranties last, so the above may not apply to you. Additionally,
some states/provinces do not allow the exclusion to limitation of consequential or
incidental damages, so the above limitation or exclusion may not apply to you.
* In the space below, record the serial number that is located on the back of the unit
along with the purchase date and location.
Model Number __________________
Purchase Date __________________
____________________
Serial Number
Where Purchased _________________
RETAIN YOUR SALES RECEIPT ALONG WITH THIS CARD. IT IS YOUR ONLY
VALID DOCUMENT TO RECEIVE WARRANTY SERVICE.
WARRANTY REPAIR POLICY
In the unlikely event of product failure, the following procedures
should be followed
1) The unit must be under the 1-year warranty period.
2) The unit must have no physical damage.
3) A copy of the original proof of purchase must be sent with the unit.
4) Include a brief description of the problem or failure with the unit.
5) Include the return street address and daytime telephone number.
6) Allow 2~3 weeks for repair (this period includes shipping time).
Send unit to:
PROFILE CONSUMER ELECTRONICS, INC.
15060 SHOEMAKER AVE
SANTA FE SPRINGS, CA 90670
TEL: (562) 404-9393
Note:
All units failing to meet the above requirements will be
subject to a charge and or may not be repaired.
PROFILE CONSUMER ELECTRONICS, INC.
15060 SHOEMAKER AVE
SANTA FE SPRINGS, CA 90670
TEL: (562)404-9393 FAX: (562)404-9433
WWW.PROFILEUSA.COM
|