Pro Ject Stereo System PRO JECT RPM 5 User Manual

INSTRUCTIONS FOR USE  
Pro-Ject RPM 5  
 
PRO-JECT RPM 5  
Controls, features and connections  
1
2
3
4
5
6
7
Motor transportation screw (marked red)  
Stepped drive pulley  
Drive belt *  
3a Hook *  
Hub  
Platter *  
Tonearm counterweight *  
Tonearm lift lever  
6a Downforce scale  
8/18 Tonearm rest and removable transport lock  
9
Tonearm tube  
9a Tonearm base  
13  
14  
15  
16  
17  
20  
21  
22  
23  
Power supply socket  
Phono output sockets and earth connection  
Anti-skating weight adjustment scale  
Anti-skating weight *  
Anti-skating weight support hoop  
Power switch  
Headshell with finger lift *  
Motor  
Adjustable tip-toe feet with anti-scratch cups *  
Screw-down record clamp (not shown) *  
Connection cable (not shown) *  
Power supply (not shown)  
Dear music lover,  
thank you for purchasing a PRO-JECT AUDIO record player.  
In order to achieve maximum performance and reliability with this record player you should study these instructions  
for use carefully.  
!
Warning of a hazard for the user, the unit or possible misuse.  
Important notice.  
During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable  
receptacle.  
Before starting assembly make yourself acquainted with the parts listed above and correspondingly numbered  
in the technical drawings above. Separately packed items are marked with an asterisk *.  
© Audio Trade GmbH · Pro-Ject RPM 5 · Revision 20.2.06/1.5.06  
3
 
Set-up  
Screw the three feet (23) onto the threaded bolts located on the underside of the plinth. Make sure the  
surface you wish to use the turntable on is level (use a spirit level) before placing the turntable on it.  
Fit the drive belt (3) around the hub (4) and the smaller diameter part of the motor pulley (2). Avoid getting  
sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use  
absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt. Fit the platter  
and mat (cork or felt mat) over the spindle of the hub (4).  
Level the plinth using a spirit level and the adjustable feet (23). Remove the two red transport screws (1)  
which secure the motor (22) during transportation.  
Remove the transport lock (18) from the tonearm. Store it together with the two red motor transport screws  
(1) in the original packaging so they are available for any future transportation.  
Fitting and connecting the cartridge  
All cartridges with half inch mounting holes can be fitted. Leaving the needle's protection cover on, fit the  
cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each  
slot in the headshell (21). Do not tighten the nuts yet.  
Connect the tonearm wires to the cartridge pins as follows:  
white  
red  
green  
blue  
left channel positive (L+)  
right channel pos. (R+)  
right channel return (R -)  
left channel return (L -)  
The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted. Particular  
tools like the PRO-JECT alignment tool are required to accomplish this job properly.  
If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of  
your PRO-JECT dealer to accomplish this task for you.  
The finger lift (21) must be fitted on top of the headshell under the cartridge fixing bolts or nuts - not  
between headshell and cartridge body.  
Please note: adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging  
the cartridge or tonearm bearings. Leave this work to your dealer if you are in any way unsure of the  
necessary steps and precautions to be taken.  
Cartridge downforce adjustment  
The counterweight (6) supplied is suitable for cartridges weighing between 6 - 10g. Alternative counterweights  
for cartridges weighing between 10 - 15g and 4 - 6g are available as an accessory part. Adjust the downforce  
prior to installing the anti-skating weight.  
Gently push and turn the counterweight (6) onto the armtube stub. Lower the armlift and position the cartridge  
in the space between arm rest and platter. Carefully rotate the counterweight (6) until the armtube balances  
out. The arm should return to the balanced position if it is moved up or down. This adjustment must be done  
carefully. Do not forget to remove the cartridge protection cap if fitted.  
Once the arm is correctly balanced return it to the rest. Hold the counterweight (6) without moving it, and gently  
revolve the downforce scale ring (6a) until the zero is in line with the anti-skating prong (15). Check whether the  
arm still balances out.  
Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the  
cartridge manufacturer's recommendations. One mark on the scale represents 1 mN (= 0,1g / 0,1 Pond) of  
downforce.  
© Audio Trade GmbH · Pro-Ject RPM 5 · Revision 20.2.06/1.5.06  
4
 
Adjusting the vertical tracking angle (vta)  
Put a record and the record weight on the platter. When the needle is lowered into the record groove and the  
tonearm is not resting on the lift arm, the tube of the tonearm should be parallel to the surface of the record.  
If it is not loosen both allen screws in the tonearm base just enough to allow vertical movement of the arm  
pillar without force and slide the arm up or down until it is parallel.  
Carefully retighten the allen screws without applying excessive force (which would deform the arm pillar) –  
finger tight is quite sufficient.  
Adjusting the azimut  
The cartridge needle must be vertical in the record groove in order to trace the  
groove wall modulations correctly.  
A small screw at the bearing end of the arm allows incorrect azimuth to be  
corrected if your needle is not mounted exactly perpendicular to the cartridge  
Screw  
body (which is often the case).  
Slacken off the screw just enough to be able to revolve the arm tube without  
applying force. Please note: do not remove the screw completely!  
With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i.e. perpendicular  
to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel  
to the record surface.  
When you are satisfied that the needle is vertical retighten the screw carefully.  
Under no circumstances should the arm tube be adjusted with the needle still in the record groove!  
Irreparable damage may be caused to the cantilever suspension! The arm must be lifted to make  
each adjustment and lowered afterwards to check it.  
Anti-skating force adjustment  
The anti-skating force must be adjusted according to the mass of the cartridge as  
follows:  
Downforce  
Groove in the stub (15)  
1st from bearing rings  
10 - 15mN  
15 - 20mN  
2nd  
3rd  
"
"
"
20mN and bigger  
"
"
"
Hang the loop of the thread of the anti-skating weight in the groove of the anti-skating stub (15) corresponding  
to the downforce applied to your cartridge and feed the thread through the loop of the wire support (17).  
Connection to the amplifier  
The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables  
supplied with those of your choice for connection to the amplifier if you wish. Your dealer can advise you on  
alternative cables. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure  
that the phono input offers correct matching and amplification for the type of cartridge used. Line inputs  
(such as CD, Tuner, Tape or Video) are not suitable.  
Take care to connect the left and right channels correctly. The right channel is usually marked red, the left  
channel black or white. Check the manual supplied with your amplifier for relevant information. An earthing  
wire may be connected to the screw terminal between the sockets if you encounter hum problems when using  
the record player.  
If your amplifier does not have an input suitable for phono cartridges you will require a separate phono  
amplifier stage for MM or MC cartridges such as the PRO-JECT PHONO BOX or the PRO-JECT TUBE BOX  
which is then connected between the record player and a free line level input of the amplifier.  
For detailed product information please refer to the Pro-Ject web site www.project-audio.com.  
© Audio Trade GmbH · Pro-Ject RPM 5 · Revision 20.2.06/1.5.06  
5
 
Mains power connection  
The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before  
connecting to ensure compliance with the mains rating in your house.  
Connect the low voltage plug from the power supply to the socket (13) on the rear of the record player  
before connecting the power supply to the mains.  
Switching on and off  
Pressing the power switch (20) alternately starts or stops the motor.  
Changing replay speed  
Using the accessory tool provided (3a), hook the belt (3) over the larger diameter part of the motor pulley (2).  
To revert to 33 1/3 r.p.m. repeat the proceedings using the smaller step on the pulley.  
When the Pro-Ject Speed Box ore the Speed Box SE are used speed change between 33 and 45 r.p.m.  
is electronic. There is no need to move the belt manually.  
*** In addition, 78 r.p.m. is available after fitting a special pulley, which may be purchased as an  
optional extra.  
For detailed product information please refer to the Pro-Ject web site www.project-audio.com.  
Maintenance and cleaning  
Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic  
cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic  
cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber  
parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.  
If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.  
!
Always disconnect the record player from the mains power supply as a precaution before maintenance!  
Useful tips  
The record player should be positioned on a low-resonance surface such as wood or multiple layer ply board  
to avoid structural vibrations disturbing replay.  
Technical specifications PRO-JECT RPM 5  
Nominal speeds  
Speed variance  
33,33/45,11 r.p.m.. *** 78 r.p.m. optional  
±0,5 %  
Wow and flutter  
Signal to noise  
±0,08 %  
-70dB  
Downforce range  
Effective tonearm length  
Overhang  
10 - 30mN  
9 " (230mm)  
18mm  
Power consumption  
Outboard power supply  
Dimensions (W x H x D)  
Weight  
2W  
16V/500mA AC, suitable for your country's mains supply  
371 x 145 x 300mm  
6,5kg  
© Audio Trade GmbH · Pro-Ject RPM 5 · Revision 20.2.06/1.5.06  
6
 
Potential incorrect use and fault conditions  
PRO-JECT turntables are manufactured to the highest standards and undergo strict quality controls before  
leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but  
can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common  
fault symptoms is included.  
The platter doesn't turn although the unit is switched on:  
The unit is not connected to the mains power supply.  
No mains at the socket.  
Drive belt is not fitted or has slipped off.  
No signal through one or other channel or both channels:  
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or  
from that to the phono box or between that and the amplifier. This could be due to a faulty plug,  
broken wire or solder joint or simply loose plug/socket connection.  
Phono input not selected at amplifier.  
Amplifier not switched on.  
Amplifier or speakers defective or muted.  
No connection to the loudspeakers.  
Strong hum on phono input:  
No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.  
Distorted or inconsistent sound from one or both channels:  
Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.  
Needle or cantilever damaged.  
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.  
Service  
Should you encounter a problem which you are not able to alleviate or identify despite the above information,  
please contact your dealer for further advice. Only when the problem cannot be resolved there should the  
unit be sent to the responsible distributor in your country.  
Never return a record player without making sure that is it safely disassembled and correctly packaged in the  
original packaging according to the diagrams on page 8 of this booklet. Guarantee repairs will only be effected  
if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.  
Please remove these parts and pack them separately: counterweight (6), anti-skating weight (16) platter (5),  
cartridge, belt (3). Insert the transport lock for the tonearm (18) and the tonearm bearing prior to carefully  
packaging the record player.  
Warranty  
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions  
for use and/or by transportation without the original packaging. Modification or change to any part  
of the product by unauthorized persons release the manufacturer from any liability over and above  
the lawful rights of the customer.  
The information was correct at the time of going to  
press. The manufacturer reserves the right to make  
changes to the technical specification without prior  
notice as deemed necessary to uphold the ongoing  
process of technical development.  
PRO-JECT is a Registered Trademark of H. Lichtenegger.  
This guide was produced by: Audio Trade GmbH  
Copyright © 2005. All rights reserved.  
© Audio Trade GmbH · Pro-Ject RPM 5 · Revision 20.2.06/1.5.06  
7
 
Accessories  
Please  
remove feet  
bevore repacking  
!
Tonearm  
transport lock  
Platter  
Tonearm counterweight  
Power supply  
© Audio Trade GmbH · Pro-Ject RPM 5 · Revision 20.2.06/1.5.06  
8
 

Philips Bluetooth Headset SHB7103 User Manual
Philips Laptop Docking Station DC291 User Manual
Phoenix Gold Speaker 65 2 Way in Ceiling Speakers User Manual
Pioneer Portable CD Player DEH 1750 User Manual
Pioneer Stereo System PD F1039 User Manual
Planar Car Video System PLL2410W User Manual
Polycom Cordless Telephone 1725 36024 001 User Manual
Porter Cable Sander 7313 User Manual
Poulan Chainsaw 530403514 User Manual
Power Acoustik Musical Instrument Amplifier MID 65 User Manual