INSTALLATION INSTRUCTIONS
PBM-070L
AUSTRALIA, NEW ZEALAND, OCEANIA
NORTH AMERICA
3130 East Miraloma Avenue
EUROPE
Swallow House,
(DISTRIBUTOR)
P.O. Box 295
Anaheim, CA 92806 USA
USA and Canada –
Phone: 800-368-9700
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Mordialloc Victoria 3195
Australia
Phone: 039586 6330
Fax: 800-832-4888
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2008
9530-007-003-00
PBM-070L
Parts List
This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are
missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Premier Mounts 800-368-9700.
Base Box (Qty 1)
Projector Bracket(Qty 1)
Jam Nut (Qty 1)
M6 x 6mm Set Screw (Qty 1)
Nylon Spacers (Qty 2)
¼” Flat Washers (Qty 2)
M6 x 12mm Phillips Head Screws (Qty 6)
Projector Bracket Hardware
M8 x 12mm Phillips Head Screws (Qty 8)
Installation Tools
Soft Material/Blanket
Pencil
Portable Drill
Finder (Commercially Available)
Phillips Head Screw Driver
M3 Allen Wrench (Supplied)
Level
Ladder
Tape Measure
Installation Manual
Page - 3 -
PBM-070L
Projector Bracket Installation
M8 x12mm Phillips
Head Screws
Projector Bracket
M8 x12mm Phillips
Head Screws
Screwdriver
Projector
Step 1. Invert the projector and place it on a soft and flat surface. Step 1. Using a screwdriver, secure the mounting bracket using
Remove any foot levelers that might possibly prevent the
correct installation of the bracket.
Step 2. Locate the eight mounting points located on the bottom of
the projector.
Step 3. Line up the mounting points on the projector with the
mounting holes on the mounting bracket.
eight (8) M8 x 12mm Phillips Head screws.
Do not over-tighten these screws. Over-tightening
the screws may result in damaging the threaded
inserts on the projector.
Installation Manual
Page - 4 -
PBM-070L
Ceiling Installation
Step 1. Separate the top bridge from the base box by removing the six (6) M6 x 12 mm screws that are located on the base box, three
on each side (A).
Step 2. Secure the top bridge to the ceiling structure at this time (see warning label) using commercially available hardware (B).
Step 3. Use the two (2) middle slot openings for single wood stud mounting. All other mounting points on the top bridge may be
used depending on your installation application (B).
Step 4. Replace the base box to the secured top bridge and secure with the six M6 x 12 mm screws (C).
A
B
Ceiling Structure
Wood Stud
Top Bridge
Lag Bolts
(Commercially Available)
C
Base Box
Installation Manual
Page - 5 -
PBM-070L
Step 5. Loosely install the hinge pin screws, flat washer and nylon spacer to each side of the base box.
Step 6. Slide the nylon spacer and the flat washer to the back of the screws.
Step 7. Raise the mounting bracket and attached projector to the base box and insert the hinge-pins through the hinge-pin openings.
Step 8. Tighten the hinge pin screws.
Step 9. Determine the viewing angle. Once the viewing angle has been determined, insert and tighten the four (4) tilt locking
screws.
Do not over-tighten the screws.
Ceiling Structure
Wood Stud
Top Bridge
Tilt Locking
Screws
Hinge Pin Bolt
Flat Washer
Page - 6 -
Installation Manual
PBM-070L
If installing a PBM-070L from the ceiling structure, please refer to the installation instructions that are included with
those mounts.
Step 10. Install the jam screw all the way up to the end of the threads of the threaded PBM-070L.
Step 11. Screw in the 1½" bridge opening to the PBM-070L all the way up to the jam screw.
Step 12. Tighten the jam screw and the base box together.
Step 13. Loosely install the hinge pin screws, flat washer and conical spacer to each side of the base box.
Step 14. Slide the conical spacer and the flat washer to the back of the screws.
Step 15. Raise the projector mount, attached to the projector’s chassis, and insert the hinge-pins through the hinge-pin openings.
Step 16. Raise the rear of the projector and install the four (4) M6 x 12 mm tilt locking screws to the rear of the base box; adjust the
tilt and lock it.
Step 17. Tighten the two (2) M6 x 12 mm hinge pin screws.
Step 18. At this time, use the M3 Allen wrench to tighten the M6 x 6mm set screw.
Projector Adjustment
Step 1. You can adjust the roll of the projector by loosening the three (3) front and rear M6 x 12mm screws.
Do not over-tighten the screws.
Step 2. Set the desired roll and then tighten the screws. First tighten the center screws and work your way to the outside screws,
making any final adjustments prior to tightening the last two screws.
Step 3. You can adjust the tilt of the projector by loosening the four (4) M6 x 12mm screws (two on each side of the base box).
Step 4. Set the desired tilt and then tighten the screws, making any final adjustments prior to tightening the last two screws.
Step 5. Once all adjustments have been made, tighten all hardware.
AST-2446,
AST-1321 or
1
2" Pipe
M6 Set Screw
Tilt
Locking Screws
Roll Adjustment
Screws
Hinge Pin Screw
Flat Washer
Nylon Spacer
Page - 7 -
Installation Manual
PBM-070L
Technical Specifications
All measurements are inches (mm).
All base boxes feature the following adjustments to facilitate ease of installation:
A.
B.
C.
D.
Tilt of ±6° from center
Roll of ±3° from center
Yaw of ±360° when used with 1 ½" or 1" mount threaded pipe
Direct mating with standard 1 ½" and 1" mount threaded pipe
Page - 8 -
Installation Manual
PBM-070L
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original installation of this product. The limited warranty is valid only for the original purchaser of the
product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS,
DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN
WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE
OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS
PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS
OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original
consumer purchaser must accompany all warranty claims. Warranty claims must also include a description of
the problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to
Premier Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or
by fax.
Premier Mounts
Attn: Warranty Claim
3130 E. Miraloma Avenue
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Installation Manual
Page - 9 -
|