Poulan Blower 530086577 User Manual

R
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
BVM200  
IMPORTANT MANUAL -- Do not throw away  
MANUAL IMPORTANTE -- No lo descarte  
MANUEL IMPORTANT -- À Conserver  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en lesiones  
graves.  
AVERTISSEMENT:  
Veuillez lire le manuel d’instructions et bien respecter tous les  
avertissements et toutes les instructions de sécurité. Tout défaut  
de le faire pourrait entraîner des blessures graves.  
Electrolux Home Products  
North America  
Div. of WCI Outdoor Products, Inc.  
Augusta, GA 30907  
Copyright E2001 WCI Outdoor Products, Inc.  
530086577  
10/1/01  
 
disconnected. Keep vents and discharge  
tubes free of debris which can accumulate  
and restrict proper air flow.  
MAINTENANCE section for information on  
maintenance of the muffler and spark arrest-  
ing screen.  
D Never place any object in the air intake open-  
ing as this could restrict proper air flow and  
cause damage to the unit.  
ASSEMBLY  
D Never use for spreading chemicals, fertiliz-  
ers, or other substances which may contain  
toxic materials.  
WARNING: Stop engine and be sure  
the impeller blades have stopped turning be-  
fore opening the vacuum inlet door or at-  
tempting to insert or remove the vacuum or  
blower tubes. The rotating blades can cause  
serious injury. Always disconnect the spark  
plug before performing maintenance or ac-  
cessing movable parts.  
D To avoid spreading fire, do not use near leaf  
or brush fires, fireplaces, barbecue pits,  
ashtrays, etc.  
D Use only for jobs explained in this manual.  
MAINTAIN YOUR UNIT PROPERLY  
D Have all maintenance other than the rec-  
ommended procedures described in the in-  
struction manual performed by an autho-  
rized service dealer.  
D Disconnect spark plug before performing  
maintenance except for carburetor adjust-  
ments.  
D Use only recommended Poulan PRO! re-  
placement parts; use of any other parts  
may void your warranty and cause damage  
to your unit.  
D Empty fuel tank before storing the unit. Use  
up fuel left in carburetor by starting engine and  
letting it run until it stops.  
D Do not use any accessory or attachment  
other than those recommended by manufac-  
turer for use with your unit.  
D Do not store the unit or fuel in a closed area  
where fuel vapors can reach sparks or an  
open flame from hot water heaters, electric  
motors or switches, furnaces, etc.  
D Store in a dry area out of reach of children.  
WARNING: If you receive your unit  
assembled, check each step to insure your  
unit is properly assembled and all fasteners  
are secure. Follow all safety information in  
the manual and on the unit.  
D A standard screwdriver is required for as-  
sembly.  
BLOWER TUBE ASSEMBLY  
D Align the rib on the blower tube with the  
groove in the blower outlet; slide the tube  
into place.  
NOTE: Tube clamp must be loose enough to  
allow blower tube to be inserted in blower out-  
let. Loosen tube clamp by turning knob coun-  
terclockwise.  
Blower  
Blower  
Outlet  
Tube  
SPECIAL NOTICE: Exposure to vibra-  
tions through prolonged use of gasoline pow-  
ered hand tools could cause blood vessel or  
nerve damage in the fingers, hands, and  
joints of people prone to circulation disorders  
or abnormal swelling. Prolonged use in cold  
weather has been linked to blood vessel dam-  
age in otherwise healthy people. If symptoms  
occur such as numbness, pain, loss of  
strength, change in skin color or texture, or  
loss of feeling in the fingers, hands, or joints,  
discontinue the use of this tool and seek  
medical attention. An antivibration system  
does not guarantee the avoidance of these  
problems. Users who operate power tools on  
a continual and regular basis must monitor  
closely their physical condition and the condi-  
tion of this tool.  
Groove  
Rib  
D Tighten the tube clamp by turning the knob  
clockwise.  
D To remove the tube, turn the knob counter-  
clockwise to loosen clamp; remove tube.  
VACUUM BAG ASSEMBLY  
D Open the zipper on the vacuum bag and in-  
sert the elbow tube.  
D Push the small end of the elbow tube  
through the small opening in the bag.  
Elbow  
Tube  
Small  
Opening  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442 and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equipped with a spark arresting screen. If you  
operate in a locale where such regulations ex-  
ist, you are legally responsible for maintaining  
the operating condition of these parts. Failure  
Zipper  
Opening  
Rib  
NOTE: Make sure edge of the small opening  
is flush against the flared area of the elbow  
tube, and the rib on the elbow tube is on the  
bottom.  
D Close the zipper on the bag. Make sure the  
zipper is closed completely.  
to do so is a violation of the law. Refer to the D Remove blower tube from engine.  
-- 3 --  
 
Vacuum Inlet  
Retaining Post  
Rib  
Vacuum  
Inlet  
Cover  
Groove  
D Place the hooks on the vacuum tube on the  
retaining posts; pivot tube into position. Se-  
cure vacuum tube by turning the knob  
clockwise until tight.  
Knob  
D Insert the elbow tube into the blower outlet.  
Make sure elbow tube rib is aligned with the  
blower outlet groove.  
D Turn clamp knob clockwise to tighten.  
D Secure the ends of the shoulder strap by  
routing the strap through the buckle as  
shown.  
Hooks  
D When converting back to the blower fea-  
ture, make sure latch on the vacuum inlet  
cover is securely fastened.  
USING YOUR UNIT  
VACUUM TUBE ASSEMBLY  
WARNING: You MUST make sure  
the tubes are secure before using the unit.  
WARNING: Stop engine and be sure  
the impeller blades have stopped turning be- OPERATING POSITION  
fore opening the vacuum inlet door or at-  
tempting to insert or remove the vacuum or  
blower tubes. The rotating blades can cause  
serious injury.  
ye  
otec
D Align the lower vacuum tube as shown.  
Push lower vacuum tube into upper vacu-  
um tube.  
Upper Vacuum  
Tube  
Blower  
OPERATING TIPS  
Vacuum  
Lower Vacuum Tube  
D Insert a screwdriver into the latch area on  
the vacuum inlet cover.  
S While vacuuming or blowing debris, hold  
the unit with the muffler side facing away  
from your body and clothes (see illustration  
above).  
Blower  
Latch  
Outlet  
Latch Area  
Vacuum  
Inlet Cover  
Ar
S To reduce the risk of hearing loss  
associated with sound level(s), hearing  
protection is required.  
S To reduce the risk of injury associated with  
contacting rotating parts, stop the engine be-  
fore installing or removing attachments. Do  
not operate without guard(s) in place.  
D Gently tilt the handle of the screwdriver to- S Operate power equipment only at reasonable  
ward the back of the unit while pulling up on  
the vacuum inlet cover with your other  
hand.  
D Hold the vacuum inlet cover open until up-  
per vacuum tube is installed.  
hours--not early in the morning or late at night  
when people might be disturbed. Comply with  
times listed in local ordinances. Usual recom-  
mendations are 9:00 a.m. to 5:00 p.m.,  
Monday though Saturday.  
-- 4 --  
 
S To reduce noise levels, limit the number of  
pieces of equipment used at any one time.  
S To reduce noise levels, operate power  
blowers at the lowest possible throttle  
speed to do the job.  
STARTING POSITION  
S Use rakes and brooms to loosen debris be-  
fore blowing.  
S In dusty conditions, slightly dampen sur-  
faces or use a mister attachment when wa-  
ter is available.  
Blower  
S Conserve water by using power blowers  
instead of hoses for many lawn and garden  
applications, including areas such as gutters,  
screens, patios, grills, porches, and gardens.  
S Watch out for children, pets, open windows,  
or freshly washed cars. Blow debris away  
safely.  
S Use the full blower nozzle extension so the  
air stream can work close to the ground.  
S After using blowers and other equipment,  
CLEAN UP! Dispose of debris in trash re-  
ceptacles.  
WARNING: When starting engine,  
hold the unit as illustrated. Do not set unit on any  
surface except a clean, hard area when starting  
engine or while engine is running. Debris such  
as gravel, sand, dust, grass, etc. could be  
picked up by the air intake and thrown out  
through the discharge opening, damaging the  
unit or property, or causing serious injury to by-  
standers or the operator.  
FUELING  
STARTING A COLD ENGINE (or a  
warm engine after running out of  
fuel)  
WARNING: Remove fuel cap slowly  
S Move throttle lever to the  
position.  
when refueling.  
This engine is certified to operate on S Move choke lever to the FULL CHOKE  
unleaded gasoline. Gasoline must be mixed  
with a good quality 2--cycle air--cooled engine  
oil designed to be mixed at a ratio of 40:1.  
Poulan PRO! brand oil is recommended. (A  
40:1 ratio is obtained by mixing 3.2 ounces of  
oil with 1 gallon of unleaded gasoline). When  
mixing fuel follow the instructions printed on  
the container. Always read and follow the  
safety rules under HANDLE FUEL WITH  
CAUTION.  
position.  
S Slowly press the primer button 8 times.  
T
IMPORTANT  
Experience indicates that alcohol blended  
fuels (called gasohol or using ethanol or  
methanol) can attract moisture which leads to  
separation and formation of acids during  
storage. Acidic gas can damage the fuel  
system of an engine while in storage. To avoid  
engine problems, empty the fuel system  
before storage for 30 days or longer. Drain the  
gas tank, start the engine and let it run until the  
fuel lines and carburetor are empty. Use fresh  
Choke Lever  
S Pull starter rope sharply until engine at-  
tempts to run, but no more than 5 pulls (be-  
low 30_ F, 8 pulls).  
NOTE: If engine attempts to start before the  
th  
5
pull, go to next step immediately.  
fuel next season.  
Never use engine or  
S Move the choke lever to the HALF CHOKE  
position.  
carburetor cleaner products in the fuel tank or  
permanent damage may occur.  
S Pull the starter rope sharply until the engine  
runs, but no more than 5 pulls (below 30_ F,  
10 pulls). Run engine for 5 seconds, then  
move choke lever to the RUN position.  
S Allow the unit to run for 30 more seconds at  
the RUN position before moving the throttle  
STARTING  
TO STOP THE ENGINE  
lever to  
position.  
D To stop the engine, move the throttle lever  
to the STOP position.  
If engine has not started after 5 pulls (at HALF  
CHOKE), repeat STARTING A COLD ENGINE  
procedure. If engine still does not start, proceed  
to STARTING A FLOODED ENGINE.  
BEFORE STARTING THE ENGINE  
D Fuel engine. Move at least 10 feet (3 me-  
ters) away from the fueling site.  
D Hold the unit in the starting position as  
shown. Make sure the blower end is di-  
rected away from people, animals, glass,  
and solid objects.  
STARTING A WARM ENGINE  
S Move throttle lever to the  
position.  
S Pull starter rope sharply until engine runs,  
but no more than 5 pulls.  
-- 5 --  
 
NOTE: If engine has not started, pull starter CLEAN AIR FILTER  
rope 5 more pulls. If engine still does not run,  
it is probably flooded.  
STARTING A FLOODED ENGINE  
S Move the choke lever to the RUN position.  
Air Filter  
Cover  
S Move throttle lever to the  
position.  
S Pull rope to clear engine of excess fuel.  
This could require pulling the starter rope  
many times.  
If unit still doesn’t start refer to the TROUBLE  
SHOOTING TABLE or call 1-800-554-6723.  
MAINTENANCE  
WARNING: Avoid touching muffler  
unless engine and muffler are cold. A hot  
muffler can cause serious burns.  
Screws  
Air Filter  
Cleaning the air filter:  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean or replace  
air filter after every 5 hours of operation or  
yearly, whichever comes first.  
WARNING: Stop engine and be sure  
the impeller blades have stopped turning be-  
fore opening the vacuum inlet door or at-  
tempting to insert or remove the vacuum or  
blower tubes. The rotating blades can cause  
serious injury. Always disconnect the spark  
plug before performing maintenance or ac-  
cessing movable parts.  
GENERAL RECOMMENDATIONS  
The warranty on this unit does not cover items  
that have been subjected to operator abuse  
or negligence. To receive full value from the  
warranty, the operator must maintain unit as  
instructed in this manual. Various adjust-  
ments will need to be made periodically to  
properly maintain your unit.  
S Clean the cover and the area around it to  
keep debris from falling into the carburetor  
chamber when the cover is removed.  
S Remove parts as illustrated.  
NOTE: Do not clean filter in gasoline or other  
flammable solvent. Doing so can create a fire  
hazard or produce harmful evaporative emis-  
sions.  
S Wash the filter in soap and water.  
S Allow filter to dry.  
S Apply a few drops of oil to the filter; squeeze  
filter to distribute oil.  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
S Muffler  
S Replace parts.  
REPLACE SPARK PLUG  
Replace spark plug each year to ensure the  
engine starts easier and runs better. Set  
spark plug gap at 0.025 inch. Ignition timing is  
fixed, nonadjustable.  
S Twist, then pull off spark plug boot.  
S Remove spark plug from cylinder and dis-  
card.  
CHECK FOR DAMAGED OR WORN  
PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S Fuel Tank -- Do not use unit if fuel tank shows  
signs of damage or leaks.  
S Replace with Champion RCJ-6Y spark  
plug and tighten with a 3/4 in. socket  
wrench (15 - 20 ft/lbs).  
S Reinstall the spark plug boot.  
REPLACE FUEL FILTER  
S Vacuum Bag -- Do not use vacuum bag if it  
is torn or damaged.  
To replace fuel filter, drain unit by running it dry  
of fuel, then remove fuel cap/retainer assem-  
bly from tank. Pull filter from tank and remove  
it from the fuel line. Install new fuel filter on fuel  
line; reinstall parts.  
INSPECT AND CLEAN UNIT AND  
DECALS  
S After each use, inspect complete unit for  
loose or damaged parts. Clean the unit and  
decals using a damp cloth with a mild deter-  
gent.  
S Wipe off unit with a clean dry cloth.  
Fuel Line  
Fuel Filter  
-- 6 --  
 
CHECK MUFFLER MOUNTING  
SCREWS  
SERVICE  
We recommend all service and adjustments  
not listed in this manual be performed by an  
authorized service dealer.  
CARBURETOR ADJUSTMENTS  
Your carburetor is equipped with limiter caps.  
Adjusting the carburetor is a complicated  
task. We recommend that you take your unit  
to an an authorized service dealer. Damage  
will occur if you turn the needles beyond the  
limiter stops.  
Once each year, ensure muffler mounting  
screws are secure and tightened properly to  
prevent damage.  
Mounting  
Screw  
Holes  
Muffler Cover  
Screws  
STORAGE  
S Loosen and remove the 2 screws from the  
muffler cover.  
WARNING: Perform the following  
steps after each use:  
S Remove the muffler cover.  
S Tighten the 2 muffler mounting screws (100  
in/lbs).  
S Allow engine to cool, and secure the unit  
before storing or transporting.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
S Reinstall muffler cover and 2 screws.  
INSPECT MUFFLER AND SPARK  
ARRESTING SCREEN  
As the unit is used, carbon deposits build up  
on the muffler and spark arresting screen,  
and must be removed to avoid creating a fire  
hazard or affecting engine performance.  
S Store unit and fuel well out of the reach of  
children.  
TOP VIEW OF MUFFLER  
Exhaust  
Diverter  
NEED ASSISTANCE?  
NEED ASSISTANCE?  
Call: 1-800-554-6723.  
NEED A SERVICE PART?  
Contact your dealer.  
Screws  
Replace the spark arresting screen every 25  
hours of operation or if any damage or breaks  
in the screen are noted.  
NOTE: Do not attempt to clean the spark ar-  
resting screen.  
S Loosen and remove the 2 screws from the  
muffler cover.  
S Remove the muffler cover.  
S Loosen and remove both screws from the  
exhaust diverter.  
S Remove the exhaust diverter and spark ar-  
resting screen.  
S Install new spark arresting screen.  
S Reinstall exhaust diverter and both screws.  
Tighten screws securely.  
S Reinstall muffler cover and 2 screws.  
NOTE: If any part of the muffler is cracked,  
broken or damaged, we recommend that the  
muffler be replaced.  
-- 7 --  
 
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing any of the  
recommended remedies below other than remedies that require operation of the unit.  
TROUBLE  
Engine will not  
start.  
CAUSE  
REMEDY  
S Engine flooded.  
S See “Starting Instructions.”  
S Fill tank with correct fuel mixture.  
S Install new spark plug.  
S Fuel tank empty.  
S Spark plug not firing.  
S Fuel not reaching carburetor.  
S Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
S Compression low.  
S Contact an authorized service dealer.  
S Fuel not reaching carburetor.  
S Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
S See “Carburetor Adjustments.”  
S Contact an authorized service dealer.  
S Contact an authorized service dealer.  
Engine will not  
idle properly.  
S Carburetor requires adjustment.  
S Crankshaft seals worn.  
S Compression low.  
S Air filter dirty.  
S Clean or replace air filter.  
Engine will not  
accelerate,  
lacks power, or  
dies under a  
load.  
S Fuel not reaching carburetor.  
S Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
S Spark plug fouled.  
S Clean or replace spark plug; re-gap.  
S Replace screen.  
S See “Carburetor Adjustments.”  
S Contact an authorized service dealer.  
S Contact an authorized service dealer.  
S Spark arresting screen clogged.  
S Carburetor requires adjustment.  
S Carbon build up.  
S Compression low.  
S Adjust choke.  
S Choke partially on.  
Engine  
S Empty fuel tank and refill with  
correct fuel mixture.  
S Fuel mixture incorrect.  
smokes  
excessively.  
S Clean or replace air filter.  
S See “Carburetor Adjustments.”  
S Air filter dirty.  
S Carburetor requires adjustment.  
S See “Fueling Your Unit.”  
S Fuel mixture incorrect.  
S Spark plug incorrect.  
S Carburetor requires adjustment.  
S Carbon build up.  
Engine  
runs hot.  
S Replace with correct spark plug.  
S See “Carburetor Adjustments.”  
S Contact an authorized service dealer.  
will wear and require replacement with reason-  
able use during the warranty period. This war-  
ranty does not cover predelivery setup or nor-  
mal adjustments explained in the instruction  
manual.  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE  
LIMITATIONS OR EXCLUSION MAY NOT  
APPLY TO YOU.  
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS NORTH  
AMERICA, Division of WCI Outdoor Prod-  
ucts, Inc., warrants to the original purchaser  
that each new Poulan PRO! brand gasoline  
tool or attachment is free from defects in materi-  
al and workmanship and agrees to repair or re-  
place under this warranty any defective gaso-  
line product or attachment as follows from the  
original date of purchase  
2 YEARS-- Parts and Labor, when used for  
household purposes.  
90 DAYS -- Parts and Labor, when used for  
commercial, professional, or income producing  
purposes.  
30 DAYS -- Parts and Labor, if used for rental  
purposes.  
This warranty is not transferable and does not  
cover damage or liability caused by improper ELECTROLUX HOME PRODUCTS NORTH  
handling, improper maintenance, or the use of AMERICA’S policy is to continuously improve  
accessories and/or attachments not specifically its products. Therefore, ELECTROLUX HOME  
recommended by ELECTROLUX HOME  
PRODUCTS NORTH AMERICA for this tool.  
PRODUCTS NORTH AMERICA reserves the  
right to change, modify, or discontinue models,  
Additionally, this warranty does not cover tune- designs, specifications, and accessories of all  
ups, spark plugs, filters, starter ropes, starter products at any time without notice or obligation  
springs, cutting line, or rotating head parts that to any purchaser.  
-- 8 --  
 
MENCEMENT DATE: The warranty period  
begins on the date the lawn and garden equip-  
ment engine is purchased. LENGTH OF  
COVERAGE: This warranty shall be for a pe-  
riod of two years from the initial date of pur-  
chase. WHAT IS COVERED: REPAIR OR  
REPLACEMENT OF PARTS. Repair or re-  
placement of any warranted part will be per-  
formed at no charge to the owner at an ap-  
proved POULAN/WEED EATER servicing  
center. If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized ser-  
vice dealer center or call POULAN/WEED  
EATER at 1--800--554--6723 WARRANTY  
PERIOD: Any warranted part which is not  
scheduled for replacement as required main-  
tenance, or which is scheduled only for regu-  
lar inspection to the effect of “repair or replace  
as necessary” shall be warranted for 2 years.  
Any warranted part which is scheduled for re-  
placement as required maintenance shall be  
warranted for the period of time up to the first  
scheduled replacement point for that part.  
DIAGNOSIS: The owner shall not be  
charged for diagnostic labor which leads to  
the determination that a warranted part is de-  
fective if the diagnostic work is performed at  
an approved POULAN/WEED EATER serv-  
icing center. CONSEQUENTIAL DAM-  
AGES: POULAN/WEED EATER may be li-  
able for damages to other engine compo-  
nents caused by the failure of a warranted  
part still under warranty. WHAT IS NOT COV-  
ERED: All failures caused by abuse, neglect,  
or improper maintenance are not covered.  
ADD--ON OR MODIFIED PARTS: The use  
of add--on or modified parts can be grounds  
for disallowing a warranty claim. POULAN/  
WEED EATER is not liable to cover failures of  
warranted parts caused by the use of add--on  
or modified parts. HOW TO FILE A CLAIM: If  
you have any questions regarding your war-  
ranty rights and responsibilities, you should  
contact your nearest authorized service cen-  
ter or call POULAN/WEED EATER at  
1--800--554--6723. WHERE TO GET WAR-  
RANTY SERVICE: Warranty services or re-  
pairs shall be provided at all POULAN/WEED  
U.S. EPA  
EMISSION CONTROL  
WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OB-  
LIGATIONS: The U. S. Environmental  
Protection Agency and POULAN/WEED  
EATER, DIVISION OF WCI OUTDOOR  
PRODUCTS are pleased to explain the emis-  
sions control system warranty on your lawn  
and garden equipment engine. All new utility  
and lawn and garden equipment engines  
must be designed, built, and equipped to meet  
the stringent anti--smog standards. POU-  
LAN/WEED EATER must warrant the emis-  
sion control system on your lawn and garden  
equipment engine for the periods of time listed  
below provided there has been no abuse, ne-  
glect, or improper maintenance of your lawn  
and garden equipment engine. Your emission  
control system includes parts such as the  
carburetor and the ignition system. Where a  
warrantable condition exits, POULAN/WEED  
EATER will repair your lawn and garden  
equipment engine at no cost to you. Ex-  
penses covered under warranty include diag-  
nosis, parts and labor. MANUFACTURER’S  
WARRANTY COVERAGE: If any emissions  
related part on your engine (as listed under  
Emissions Control Warranty Parts List) is de-  
fective or a defect in the materials or work-  
manship of the engine causes the failure of  
such an emission related part, the part will be  
repaired or replaced by POULAN/WEED  
EATER. OWNER’S WARRANTY RESPON-  
SIBILITIES: As the lawn and garden equip-  
ment engine owner, you are responsible for  
the performance of the required maintenance  
listed in your instruction manual. POULAN/  
WEED EATER recommends that you retain  
all receipts covering maintenance on your  
lawn and garden equipment engine, but POU-  
LAN/WEED EATER cannot deny warranty  
solely for the lack of receipts or for your failure  
to ensure the performance of all scheduled  
maintenance. As the lawn and garden equip-  
ment engine owner, you should be aware that  
POULAN/WEED EATER may deny you war-  
ranty coverage if your lawn and garden equip-  
ment engine or a part of it has failed due to  
abuse, neglect, improper maintenance, un-  
approved modifications, or the use of parts  
not made or approved by the original equip-  
ment manufacturer. You are responsible for  
presenting your lawn and garden equipment  
engine to a POULAN/WEED EATER autho-  
rized repair center as soon as a problem ex-  
ists. Warranty repairs should be completed in  
a reasonable amount of time, not to exceed  
30 days. If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized ser-  
vice dealer or call POULAN/WEED EATER at  
EATER  
service  
centers.  
call:  
1--800--554--6723. MAINTENANCE, RE-  
PLACEMENT AND REPAIR OF EMISSION  
RELATED PARTS: Any POULAN/WEED  
EATER approved replacement part used in  
the performance of any warranty mainte-  
nance or repair on emission related parts will  
be provided without charge to the owner if the  
part is under warranty. EMISSION CON-  
TROL WARRANTY PARTS LIST: Carbure-  
tor, Ignition System: Spark Plug (covered up  
to maintenance schedule), Ignition Module.  
MAINTENANCE STATEMENT: The owner is  
responsible for the performance of all re-  
quired maintenance as defined in the instruc-  
tion manual.  
1--800--554--6723.  
WARRANTY COM-  
-- 9 --  
 

Peavey Guitar Passive User Manual
Peavey Musical Instrument Amplifier Ecoustic 110 User Manual
Pelco Security Camera C401M C User Manual
Philips VCR VR 520 User Manual
Philips Work Light P 5794 B User Manual
Pioneer DVD Player DV 2750 User Manual
Planet Technology Switch POE 151 User Manual
Powermate Portable Generator PM0435252 User Manual
Printronix Printer ThermaLine Series User Manual
Profile Indoor Furnishings 60 AMP BUSWAY User Manual