Porter Cable Drill 7556 User Manual

ESPAÑOL: PÁGINA 17  
FRANÇAISE : PAGE 31  
Instruction  
manual  
Double Insulated  
1
/
2" Right Angle Drill  
MODEL 7556  
IMPORTANT  
Please make certain that the person who is  
to use this equipment carefully reads and  
understands these instructions before  
starting operations.  
To learn more about Porter-Cable  
visit our website at:  
The Model and Serial No. plate is located on the main  
housing of the tool. Record these numbers in the  
spaces below and retain for future reference.  
Model No. ______________________________________  
Type ___________________________________________  
Serial No._______________________________________  
Part No. A08430 - 09-30-04  
Copyright © 2002 Porter-Cable Corporation  
 
SAFETY GUIDELINES - DEFINITIONS  
It is important for you to read and understand this manual. The information it  
contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS.  
The symbols below are used to help you recognize this information.  
indicates an imminently hazardous situation which, if not  
avoided, will result in death or serious injury.  
indicates a potentially hazardous situation which, if not  
avoided,could result in death or serious injury.  
indicates a potentially hazardous situation which, if not  
avoided,may result in minor or moderate injury.  
used without the safety alert symbol indicates potentially  
hazardous situation which, if not avoided, may result in  
property damage.  
CALIFORNIA PROPOSITION 65  
Some dust created by power sanding, sawing, grinding, drilling, and  
other construction activities contains chemicals known (to the State  
of California) to cause cancer, birth defects or other reproductive harm. Some  
examples of these chemicals are:  
lead from lead-based paints  
crystalline silica from bricks and cement and other masonry products  
arsenic and chromium from chemically-treated lumber  
Your risk from these exposures varies, depending on how often you do this type  
of work. To reduce your exposure to these chemicals: work in a well ventilated  
area, and work with approved safety equipment, always wear MSHA/NIOSH  
approved, properly fitting face mask or respirator when using such tools.  
3
 
GENERAL SAFETY RULES*  
Read all instructions Failure to follow all  
instructions listed below may result in electric shock, fire and/or  
serious injury. The term "power tool" in all of the warnings listed  
below refers to your mains-operated (corded) power tool or  
battery-operated (cordless) power tool.  
SAVE THESE INSTRUCTIONS  
1) Work area safety  
a) Keep work area clean and well lit. Cluttered or dark areas invite  
accidents.  
b) Do not operate power tools in explosive atmospheres, such as in the  
presence of flammable liquids, gases or dust. Power tools create  
sparks which may ignite the dust or fumes.  
c) Keep children and bystanders away while operating a power tool.  
Distractions can cause you to lose control  
2) Electrical safety  
a) Power tool plugs must match the outlet. Never modify the plug in any  
way. Do not use any adapter plugs with earthed (grounded) power  
tools. Unmodified plugs and matching outlets will reduce risk of electric  
shock  
b) Avoid body contact with earthed or grounded surfaces such as  
pipes, radiators, ranges and refrigerators. There is an increased risk of  
electric shock if your body is earthed or grounded.  
c) Do not expose power tools to rain or wet conditions. Water entering a  
power tool will increase the risk of electric shock  
d) Do not abuse the cord. Never use the cord for carrying, pulling or  
unplugging the power tool. Keep cord away from heat, oil, sharp  
edges or moving parts. Damaged or entangled cords increase the risk  
of electric shock.  
e) When operating a power tool outdoors, use an extension cord  
suitable for outdoor use. Use of a cord suitable for outdoor use reduces  
the risk of electric shock.  
3) Personal safety  
a) Stay alert, watch what you are doing and use common sense when  
operating a power tool. Do not use a power tool while you are tired  
or under the influence of drugs, alcohol or medication. A moment of  
inattention while operating power tools may result in serious personal  
injury.  
b) Use safety equipment. Always wear eye protection. Safety equipment  
such as dust mask, non-skid safety shoes, hard hat, or hearing  
protection used for appropriate conditions will reduce personal injuries.  
c) Avoid accidental starting. Ensure the switch is in the off-position  
before plugging in. Carrying power tools with your finger on the switch  
or plugging in power tools that have the switch on invites accidents.  
4
*The text used in the General Safety Rule section of this manual is  
verbatim, as required, from the applicable UL60745 3rd edition standard.  
 
continued  
GENERAL SAFETY RULES*  
d) Remove any adjusting key or wrench before turning the power tool  
on. A wrench or a key left attached to a rotating part of the power tool  
may result in personal injury.  
e) Do not overreach. Keep proper footing and balance at all times. This  
enables better control of the power tool in unexpected situations.  
f) Dress properly. Do not wear loose clothing or jewellery. Keep your  
hair, clothing and gloves away from moving parts. Loose clothes,  
jewellery or long hair can be caught in moving parts.  
g) If devices are provided for the connection of dust extraction and  
collection facilities, ensure these are connected and properly used.  
Use of these devices can reduce dust-related hazards.  
4) Power tool use and care  
a) Do not force the power tool. Use the correct power tool for your  
application. The correct power tool will do the job better and safer at the  
rate for which it was designed.  
b) Do not use the power tool if the switch does not turn it on and off.  
Any power tool that cannot be controlled with the switch is dangerous  
and must be repaired.  
c) Disconnect the plug from the power source before making any  
adjustments, changing accessories, or storing power tools. Such  
preventive safety measures reduce the risk of starting the power tool  
accidentally.  
d) Store idle power tools out of the reach of children and do not allow  
persons unfamiliar with the power tool or these instructions to  
operate the power tool. Power tools are dangerous in the hands of  
untrained users.  
e) Maintain power tools. Check for misalignment or binding of moving  
parts, breakage of parts and any other condition that may affect the  
power tools operation. If damaged, have the power tool repaired  
before use. Many accidents are caused by poorly maintained power  
tools.  
f) Keep cutting tools sharp and clean. Properly maintained cutting tools  
with sharp cutting edges are less likely to bind and are easier to control.  
g) Use the power tool, accessories and tool bits etc., in accordance  
with these instructions and in the manner intended for the  
particular type of power tool, taking into account the working  
conditions and the work to be performed. Use of the power tool for  
operations different from those intended could result in a hazardous  
situation.  
5) Service  
a) Have your power tool serviced by a qualified repair person using only  
identical replacement parts. This will ensure that the safety of the  
power tool is maintained.  
5
*The text used in the General Safety Rule section of this manual is  
verbatim, as required, from the applicable UL60745 3rd edition standard.  
 
ADDITIONAL SPECIFIC SAFETY RULES  
1. USE AUXILIARY HANDLES SUPPLIED WITH THE TOOL. Loss of  
control can cause personal injury.  
2. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHEN  
PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY  
CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live"  
wire will make exposed metal parts of the tool "live" and shock the  
operator.  
3. VERIFY the direction of rotation before starting the tool.  
4. NEVER ATTEMPT TO CHANGE DIRECTION of rotation while switch is  
“ON”. To do so, may damage the drill. Be sure switch is “OFF” and  
motor has completely stopped before changing direction of rotation.  
5. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC.  
Take extra care to prevent inhalation and skin contact when working with  
these materials. Request, and follow, any safety information available  
from your material supplier.  
6. DO NOT use bits larger than those recommended in Fig. A. They  
increase the chance of jamming. Large bits may also overload the drill  
and damage the motor and gears.  
7. USE ONLY the proper chuck key to tighten or loosen the chuck. Do not  
use chuck if jaws or other parts are cracked or worn.  
8. NEVER hold work in your hand, lap, or against other parts of your body  
when drilling.  
9. DO NOT use drill as a router or try to elongate or enlarge holes by  
twisting the drill. Drill bits may break and cause injury.  
10.  
There are certain applications for which this tool was  
designed. Porter-Cable strongly recommends that this tool NOT be  
modified and/or used for any application other than for which it was  
designed. If you have any questions relative to its application DO NOT  
use the tool until you have written Porter-Cable and we have advised  
you.  
Technical Service Manager  
Porter-Cable Corporation  
4825 Highway 45 North  
Jackson, TN 38305  
6
 
SYMBOL  
DEFINITION  
........................ volts  
V
A
........................ amperes  
........................ hertz  
........................ watts  
........................ kilowatts  
........................ farads  
........................ microfarads  
........................ litres  
Hz  
W
kW  
F
µF  
l
g
........................ grams  
........................ kilograms  
........................ bars  
........................ pascals  
........................ hours  
........................ minutes  
........................ seconds  
........................ no-load speed  
kg  
bar  
Pa  
h
min  
s
n0  
…/min or …min 1 ......... Revolutions or reciprocations per minute  
-
or d.c. ................ direct current  
or a.c. ................ alternating current  
2
........................ two-phase alternating current  
2N  
3
........................ two-phase alternating current with neutral  
........................ three-phase alternating current  
3N  
........................ three-phase alternating current with neutral  
........................ rated current of the appropriate fuse-link in amperes  
........................ time-lag miniature fuse-link where X is the symbol  
for the time/current characteristic, as given in IEC 60127  
........................ protective earth  
........................ class II tool  
........................ IP symbol  
IPXX  
7
 
MOTOR  
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60  
cycle A.C. current and voltage within plus or minus 5 percent of that shown on  
the specification plate on the tool. Several models, however, are designed for  
A.C. current only. Refer to the specification plate on your tool for proper voltage  
and current rating.  
Do not operate your tool on a current on which the voltage is not  
within correct limits. Do not operate tools rated A.C. only on D.C.  
current. To do so may seriously damage the tool.  
EXTENSION CORD SELECTION  
If an extension cord is used, make sure the conductor size is large enough to  
prevent excessive voltage drop which will cause loss of power and possible  
motor damage. A table of recommended extension cord sizes will be found in  
this section. This table is based on limiting line voltage drop to 5 volts (10 volts  
for 230 volts) at 150% of rated amperes.  
If an extension cord is to be used outdoors it must be marked with the suffix W-A  
or W following the cord type designation. For example – SJTW-A to indicate it is  
acceptable for outdoor use.  
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS  
Length of Cord in Feet  
115V  
230V  
25 Ft.  
50 Ft.  
50 Ft.  
100 Ft. 150 Ft. 200 Ft.  
250 Ft. 300 Ft.  
500 Ft. 600 Ft.  
400 Ft. 500 Ft.  
800 Ft. 1000 Ft.  
100 Ft. 200 Ft. 300 Ft. 400 Ft.  
0-2  
2-3  
18  
18  
18  
18  
18  
18  
18  
16  
16  
16  
14  
14  
18  
18  
18  
18  
16  
16  
14  
14  
12  
12  
12  
12  
18  
16  
16  
14  
14  
12  
12  
10  
10  
10  
8
16  
14  
14  
12  
12  
10  
10  
8
16  
14  
12  
12  
10  
10  
8
14  
12  
12  
10  
10  
8
14  
12  
10  
10  
8
12  
10  
10  
8
12  
10  
8
3-4  
4-5  
8
5-6  
8
6
6-8  
6
6
6
8-10  
10-12  
12-14  
14-16  
16-18  
18-20  
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
FUNCTIONAL DESCRIPTION  
FOREWORD  
Porter-Cable drills are designed to drill holes of various sizes in wood and  
metal as indicated in the following chart:  
Model No. of Drill Type of Bit  
Max. Dia. Hole Material  
Low  
Twist Drill  
Auger Bit  
1/2"  
13/4"  
45/8"  
1/2"  
Steel  
Wood  
Wood  
Steel  
Speed  
7556  
Self Feed Bit  
Twist Drill  
High  
Speed  
Auger Bit  
11/2"  
29/16"  
Wood  
Wood  
Self Feed Bit  
Fig. A  
8
 
CARTON CONTENTS  
* Right angle drill  
* Side handle  
* Chuck key  
* Open end wrench  
* Pin wrench  
ASSEMBLY  
INSTALLING AND REMOVING DRILL BIT  
1.  
DISCONNECT TOOL FROM POWER SOURCE.  
2. The three-jaw chuck is designed for self-centering of the drill bit. Open  
chuck jaws by turning outer sleeve counterclockwise, when viewing the  
chuck from the bit end. Open large enough so that bit shank can be inserted.  
3. Clean and insert smooth end of drill bit as far as it will go into the chuck,  
then withdraw bit approximately 1/16", or up to the flutes for small bits.  
4. While holding the bit with one hand, turn outer sleeve clockwise until bit  
is gripped in the chuck.  
5. Tighten chuck – insert chuck key into each of 3 keyholes in chuck body  
(Fig. 1) in succession and tighten securely by turning key clockwise.  
6.  
Be sure chuck key is removed before starting tool.  
7. To remove bit, reverse this procedure.  
TIGHTEN  
LOOSEN  
Fig. 1  
TO INSTALL AUXILIARY HANDLE  
An auxiliary handle (C) Fig. 2, is  
supplied and can be installed on  
either side of the tool. This handle  
screws directly into the drill housing  
providing complete control of the  
drill.  
G
A
E
C
B
F
It is strongly recommended that the  
auxiliary handle be used and tool  
held as illustrated in Fig. 3A during  
all drilling operations.  
Model 7556  
Fig. 2  
9
 
OPERATION  
TO START AND STOP DRILL  
1. Make sure drill switch is “OFF”. Make sure power circuit voltage is the  
same as that shown on the specification plate of the drill. Connect drill to  
power circuit.  
2. Squeeze TRIGGER SWITCH (A) Fig. 2, to start motor. As trigger is  
squeezed, the drill speed increases. Release trigger to stop motor.  
3. A REVERSING SWITCH (B) Fig. 2 – is provided with either model. These  
models will operate in either the forward direction (clockwise rotation) for  
drilling holes, or the reverse direction (counterclock-wise rotation) for  
releasing jammed drill bits. For counterclockwise rotation, stop the motor by  
releasing the trigger switch and move the reversing switch to the position  
labeled “R”, or in the opposite direction for clockwise rotation.  
NOTE: Never attempt to change direction of rotation while switch is  
“ON”. To do so, may damage the drill. Be sure switch is “OFF” and  
motor has completely stopped before changing direction of rotation.  
TO INCREASE RPMs  
The 7556 is factory assembled with the chuck on drive end marked “LOW” and  
will run at the lower RPM shown on the specification plate. To change to the  
higher RPM marked on the nameplate proceed as follows:  
1.  
DISCONNECT TOOL FROM POWER SOURCE.  
2. Open chuck jaws as wide as possible to gain access to chuck retaining  
screw.  
3. Place spindle wrench (furnished with drill) on flats of spindle shaft and hold.  
With a 3/16" hex wrench, turn the retaining screw clockwise (left hand threads) and  
remove screw from chuck.  
4. While supporting chuck on a solid surface, place wrench on flats of spindle  
and allow the opposite end of wrench to rest on the workbench to your left as  
shown in Fig. 3. Place chuck pin wrench into chuck key hole so that pin wrench  
extends to your left as shown in Fig. 3. Strike the pin wrench a sharp blow with a  
hammer to loosen chuck.  
5. Turn chuck counterclockwise to unscrew. Remove chuck and two washers  
from spindle.  
6. Loosen the outer sleeve screw (F) Fig. 2 with a 1/2” wrench, and remove the  
right angle drive (E) Fig. 2, from the sleeve (G) Fig. 2.  
7. Place end of right angle drive marked “LOW” into sleeve (G) Fig. 2. Make  
sure the flats on the driveshaft engage slot in coupling. Tighten sleeve screw (F)  
Fig. 2.  
8. Place steel washer and then brass washer (washers removed in Step 5) onto  
spindle at end of right angle drive marked “HIGH.”  
NOTE: Failure to use these washers may cause chuck to seize on  
spindle.  
9. Thread chuck onto spindle and seat firmly by reversing procedure in Step 4.  
10. Replace and tighten chuck retaining screw securely.  
10  
 
INSTALL CHUCK  
REMOVE CHUCK  
Fig. 3  
The 7556 may be converted to a conventional straight drive drill by loosening  
the back sleeve screw and removing the sleeve and right angle drive from  
the drill. Remove the coupling retaining screw (hold spindle with spindle  
wrench, turn screw clockwise with a 5/32" hex wrench) and coupling. Remove  
the chuck and washers from the right angle drive and assemble to drill  
spindle.  
NOTE: Chuck must be firmly seated on spindle before installing  
chuck retaining screw.  
HOW TO HOLD THE DRILL  
The front end of drill may be made live if the tool drills into live  
wiring in a wall. TO PREVENT ACCIDENTAL ELECTRICAL SHOCK, DRILL  
MUST BE HELD AS SHOWN IN FIG. 3A.  
An auxiliary handle (C) Fig. 2, is supplied with each drill.  
GENERAL DRILLING  
1. Be sure drill bit is securely gripped in chuck. (See INSTALLING AND  
REMOVING DRILL BIT).  
2. Set REVERSING SWITCH (B) Fig. 2 for clockwise rotation.  
3. Make sure work is held securely in vise or clamped in place prior to  
starting drilling operation.  
Loose work may spin and cause bodily injury.  
4. Locate exact center for hole to be drilled and using a center punch,  
make a small dent in work.  
5. Place tip of drill bit in dent made by center punch, hold drill square with  
work, and start the motor.  
6. Apply steady, even pressure to keep drill bit cutting. Too little pressure  
will keep the bit from cutting and dull the edges due to excessive friction  
created by sliding over the surface.  
Too much pressure may cause the bit to break or overheat  
resulting in bodily injury or damaged drill bits.  
11  
 
RIGHT ANGLE DRILL Model 7556  
Fig. 3A  
BE ALERT and brace yourself against the twisting action of  
the drill, should bit jam in the work.  
7. If drill stalls or becomes jammed in the hole, release trigger immediately,  
remove drill bit from work and determine cause of stalling or jamming. DO  
NOT SQUEEZE TRIGGER ON AND OFF IN AN ATTEMPT TO FREE A  
STALLED OR JAMMED DRILL – THIS WILL DAMAGE THE MOTOR. The  
direction of rotation may be reversed to help free a jammed bit. Be sure  
direction of rotation is RESET before attempting to continue drilling.  
8. Reduce the pressure on the drill just before the bit cuts through the work  
to avoid splintering wood or stalling in metal.  
9. When bit has completely penetrated work and is spinning freely,  
withdraw it from the work while the motor is still running, then turn off drill.  
DRILLING WOOD  
SOME WOOD CONTAINS PRESERVATIVES WHICH  
CAN BE TOXIC. Take extra care to prevent inhalation and skin contact  
when working with these materials. Request, and follow, any safety  
information available from your material supplier.  
In addition to the instructions listed under GENERAL DRlLLlNG, the following  
also apply:  
1. When using twist drills in wood, they should be withdrawn from the hole  
frequently to clear chips built up in flutes to avoid overheating and burning  
work.  
2. If a backing block is used to keep back of work from splintering, it  
should be clamped securely in place. If a backing block is not used with  
spade bits or auger bits, ease up pressure as soon as bit point breaks  
through work, and complete the hole from the opposite side.  
DRILLING METAL  
In addition to the instructions listed under GENERAL DRlLLlNG, the following  
also apply:  
When drilling metal, jamming of bit is more likely than  
when drilling other materials.  
1. Use only good quality sharp high speed steel twist bits when drilling  
metal.  
12  
 
2. Start drilling with slow speed and gradually increase speed as drill cuts.  
The harder the material, the slower the speed required. The softer the  
material, the faster the speed.  
3. When drilling a large hole, it is easier to first drill a smaller hole and then  
enlarge it to the required size.  
4. The use of a lubricant, such as oil, on the drill point helps keep the bit  
cool, increases drilling action and prolongs drill bit life.  
TROUBLESHOOTING GUIDE  
For assistance with your tool, visit our website at www.porter-cable.com for a  
list of service centers or call the Porter-Cable help line at 1-800-487-8665.  
13  
 
MAINTENANCE  
KEEP TOOL CLEAN  
Periodically blow out all air passages with dry compressed air. All plastic parts  
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic  
parts. They could possibly dissolve or otherwise damage the material.  
Wear ANSI Z87.1 safety glasses while using compressed air.  
FAILURE TO START  
Should your tool fail to start, check to make sure the prongs on the cord plug are  
making good contact in the outlet. Also, check for blown fuses or open circuit  
breakers in the line.  
LUBRICATION  
This tool has been lubricated with a sufficient amount of high grade lubricant for  
the life of the unit under normal operating conditions. No further lubrication is  
necessary.  
BRUSH INSPECTION (If applicable)  
For your continued safety and electrical protection, brush inspection and  
replacement on this tool should ONLY be performed by an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLEDELTA FACTORY  
SERVICE CENTER.  
At approximately 100 hours of use, take or send your tool to your nearest  
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.  
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes  
installed, and test the tool for performance.  
Any loss of power before the above maintenance check may indicate the need  
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL  
UNDER THIS CONDITION. If proper operating voltage is present, return your tool  
to the service station for immediate service.  
14  
 
SERVICE  
REPLACEMENT PARTS  
When servicing use only identical replacement parts.  
SERVICE AND REPAIRS  
All quality tools will eventually require servicing or replacement of parts due to  
wear from normal use. These operations, including brush inspection and  
replacement, should ONLY be performed by either an AUTHORIZED PORTER-  
CABLE SERVICE STATION or a PORTER-CABLEDELTA FACTORY SERVICE  
CENTER. All repairs made by these agencies are fully guaranteed against  
defective material and workmanship. We cannot guarantee repairs made or  
attempted by anyone other than these agencies.  
Should you have any questions about your tool, feel free to write us at any time.  
In any communications, please give all information shown on the nameplate of  
your tool (model number, type, serial number, etc.).  
ACCESSORIES  
A complete line of accessories is available from your Porter-CableDelta  
Supplier, Porter-CableDelta Factory Service Centers, and Porter-Cable  
Authorized Service Stations. Please visit our Web Site www.porter-cable.com  
for a catalog or for the name of your nearest supplier.  
Since accessories other than those offered by Porter-  
CableDelta have not been tested with this product, use of  
such accessories could be hazardous. For safest operation,  
only Porter-CableDelta recommended accessories should  
be used with this product.  
15  
 
WARRANTY  
PORTER-CABLE LIMITED  
ONE YEAR WARRANTY  
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original  
purchase. We will repair or replace at our option, any part or parts of the product and accessories  
covered under this warranty which, after examination, proves to be defective in workmanship or  
material during the warranty period. For repair or replacement return the complete tool or accessory,  
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.  
Proof of purchase may be required. This warranty does not apply to repair or replacement required  
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service  
Centers or Authorized Service Stations.  
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE  
OF PURCHASE.  
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,  
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING  
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY  
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL  
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other legal rights which vary  
from state to state.  
16  
 
PORTER-CABLE • DELTA SERVICE CENTERS  
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)  
(CENTRE DE SERVICE PORTER-CABLE • DELTA)  
Parts and Repair Service for Porter-Cable  
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable  
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)  
Delta Power Tools are Available at These Locations  
Delta)  
Cleveland 44125  
8001 Sweet Valley Drive  
Unit #19  
Phone: (216) 447-9030  
Fax: (216) 447-3097  
ARIZONA  
MINNESOTA  
Minneapolis 55429  
5522 Lakeland Avenue North  
Phone: (763) 561-9080  
Fax: (763) 561-0653  
GEORGIA  
Tempe 85282 (Phoenix)  
2400 West Southern Avenue  
Suite 105  
Phone: (602) 437-1200  
Fax: (602) 437-2200  
Forest Park 30297 (Atlanta)  
5442 Frontage Road,  
Suite 112  
Phone: (404) 608-0006  
Fax: (404) 608-1123  
OREGON  
MISSOURI  
Portland 97230  
CALIFORNIA  
North Kansas City 64116  
1141 Swift Avenue  
Phone: (816) 221-2070  
Fax: (816) 221-2897  
ILLINOIS  
4916 NE 122 nd Ave.  
Phone: (503) 252-0107  
Fax: (503) 252-2123  
Ontario 91761 (Los Angeles)  
3949A East Guasti Road  
Phone: (909) 390-5555  
Fax: (909) 390-5554  
Addison 60101 (Chicago)  
400 South Rohlwing Rd.  
Phone: (630) 424-8805  
Fax: (630) 424-8895  
PENNSYLVANIA  
St. Louis 63119  
Willow Grove 19090 (Philadelphia)  
520 North York Road  
Phone: (215) 658-1430  
Fax: (215) 658-1433  
7574 Watson Road  
Phone: (314) 968-8950  
Fax: (314) 968-2790  
Woodridge 60517 (Chicago)  
2033 West 75th Street  
Phone: (630) 910-9200  
Fax: (630) 910-0360  
San Diego 92111  
7638 Clairemnot Blvd.  
Phone: (858) 277-9595  
Fax: (858) 277-9696  
NEW YORK  
TEXAS  
Flushing 11365-1595 (N.Y.C.)  
175-25 Horace Harding Expwy.  
Phone: (718) 225-2040  
Fax: (718) 423-9619  
MARYLAND  
San Leandro 94577 (Oakland)  
3039 Teagarden Street  
Phone: (510) 357-9762  
Fax: (510) 357-7939  
Carrollton 75006 (Dallas)  
1300 Interstate 35 N, Suite 112  
Phone: (972) 446-2996  
Fax: (972) 446-8157  
Elkridge 21075 (Baltimore)  
7397-102 Washington Blvd.  
Phone: (410) 799-9394  
Fax: (410) 799-9398  
NORTH CAROLINA  
Charlotte 28270  
9129 Monroe Road, Suite 115  
Phone: (704) 841-1176  
Fax: (704) 708-4625  
COLORADO  
Houston 77043  
4321 Sam Houston Parkway, West  
Suite 180  
Phone: (713) 983-9910  
Fax: (713) 983-6645  
MASSACHUSETTS  
Arvada 80003 (Denver)  
8175 Sheridan Blvd., Unit S  
Phone: (303) 487-1809  
Fax: (303) 487-1868  
Franklin 02038 (Boston)  
Franklin Industrial Park  
101E Constitution Blvd.  
Phone: (508) 520-8802  
Fax: (508) 528-8089  
OHIO  
FLORIDA  
WASHINGTON  
Columbus 43214  
4560 Indianola Avenue  
Phone: (614) 263-0929  
Fax: (614) 263-1238  
Davie 33314 (Miami)  
4343 South State Rd. 7 (441)  
Unit #107  
Phone: (954) 321-6635  
Fax: (954) 321-6638  
Auburn 98001(Seattle)  
3320 West Valley HWY, North  
Building D, Suite 111  
Phone: (253) 333-8353  
Fax: (253) 333-9613  
MICHIGAN  
Madison Heights 48071 (Detroit)  
30475 Stephenson Highway  
Phone: (248) 597-5000  
Fax: (248) 597-5004  
Tampa 33609  
4538 W. Kennedy Boulevard  
Phone: (813) 877-9585  
Fax: (813) 289-7948  
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and  
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service  
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to  
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.  
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-  
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro  
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de  
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au  
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-  
Cable  
Delta, s’adresser à tout distributeur Porter-Cable  
Delta, centre de service agréé ou centre de service d’usine Porter-Cable  
Delta. Si  
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable  
Delta le  
plus proche.  
CANADIAN PORTER-CABLE DELTA SERVICE CENTERS  
QUÉBEC  
ALBERTA  
MANITOBA  
1515 Ave.  
Bay 6, 2520-23rd St. N.E.  
Calgary, Alberta  
T2E 8L2  
1699 Dublin Avenue  
Winnipeg, Manitoba  
R3H 0H2  
St-Jean Baptiste, Suite 160  
Québec, P.Q.  
G2E 5E2  
Phone: (418) 877-7112  
Fax: (418) 877-7123  
Phone: (403) 735-6166  
Fax: (403) 735-6144  
Phone: (204) 633-9259  
Fax: (204) 632-1976  
BRITISH COLUMBIA  
8520 Baxter Place  
Burnaby, B.C.  
V5A 4T8  
Phone: (604) 420-0102  
Fax: (604) 420-3522  
ONTARIO  
1447, Begin  
St-Laurent, (Mtl), P.Q.  
H4R 1V8  
Phone: (514) 336-8772  
Fax: (514) 336-3505  
505 Southgate Drive  
Guelph, Ontario  
N1H 6M7  
Phone: (519) 767-4132  
Fax: (519) 767-4131  
The following are trademarks of PORTER-CABLE  
DELTA (Las siguientes son marcas registradas de PORTER-CABLE  
DELTA S.A.) (Les  
marques suivantes sont des marques de fabriquant de la PORTER-CABLE  
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,  
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying  
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-  
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-  
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-  
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,  
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,  
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-  
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,  
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,  
WOODWORKER’S CHOICE™.  
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.  
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden  
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et  
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.  
 
7.2-PTG-F-1  

Pelco Power Supply DAS5200 User Manual
Philips Automobile Parts 50PF9966 User Manual
Philips Car Stereo System CQ DFX972N User Manual
Philips Car Video System 298P4 User Manual
Philips Hair Clippers HQC688 User Manual
Philips Portable DVD Player PD7042 12 User Manual
Philips Stereo System C555 User Manual
Pioneer DVD Player DV 353 User Manual
Plantronics Stereo Amplifier CA12CD User Manual
PYLE Audio Car Stereo System AT 3040 User Manual