50-DISC MAGAZINE
DRM-AF751
Operating instructions
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.
[For Canadian model]
This Class A digital apparatus complies with Canadian ICES-003.
[Pour le modèle Canadien]
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the
user’s right to operate the equipment.
Handling the discs
÷
Avoid touching the signal surface when you
use a disc.
÷
÷
DO NOT use non-standard discs, as these
may adversely influence this unit and other
equipment.
DO NOT play a CD having other shape than
a circular disc, such as heart shaped disc, or
malfunction may occur.
÷
To hold it, place your fingers on the edge of
the disc or the edge of the center hole and
the disc edge.
÷
÷
Do not attach paper or stickers to the label
side of the disc. Handle discs carefully and
avoid damaging the label.
Do not use the following types of discs for they
may cause malfunction of the unit or damage
to the discs:
÷
Disc which has a molding flash (projected
fin) left on the periphery as shown in the
illustration.
÷
Disc with its edges are rounded or tapered
as shown in the figure.
Discs rotate at high speed in the changer.
Do not use defective discs (e.g., cracked or
considerably warped). Such discs may
damage the changer.
3
<DRC1107>
En
FEATURES
¶ Able to accommodate 50 discs
¶ Disc holder lock/release mechanism
Discs may be locked into position or released by turning the release knob.
¶ Memory
Disc magazines are equipped with memory which makes it possible to read IDs to
identify individual magazines and make the management of offline media easier.
A HARDWARE TOUR
Lock pin
Electrode
Release
knob
Handle
NOTES:
¶ Electrodes are highly susceptible to damage from static electricity, and for this reason
you should always be careful not to allow your hands to come into contact with the
electrodes.
¶ Always be sure to place disc magazines into the provided dust covers when storing
magazines.
4
<DRC1107>
En
TO INSTALL THE DISC MAGAZINE
For instructions on how to open the
access doors, see the operating
instructions for the DRM-7000 disc
changer.
2. Insert magazine into changer.
Holding the handle of the disc magazine,
insert the disc magazine into the changer
following the changer guide rails until it
runs against the stopper.
1. Insert discs into a disc magazine.
1 Turn the release knob to the vertical direction
to unlock.
2 Insert discs.
3 Turn the release knob to the horizontal
direction to lock the discs into place.
And turn the handle to the left with
pushing the magazine in so that the lock
pin on the left of the magazine slides into
the corresponding hole along the side of
the changer.
Hole
Lock pin
Guide
rails
Release knob
Lock release
Lock
≠
Label
NOTES:
¶ Insert with label facing upward.
¶ Insert discs horizontally. Otherwise it may
result in damage to the discs.
¶ Take care not to scratch or do other damage
Handle
to the recording faces of discs.
¶ Do not turn a disc magazine upside down
while the lock is disengaged. Otherwise it
may result in discs falling out of the
magazine.
¶ Discs may not be inserted or removed when
the magazine is locked, and the use of
excessive force when trying to do so may
result in damage to discs or to the disc
magazine.
Shown above is the insertion to the front
magazine bay. Though the insertion to the
rear magazine bay is almost same but note
that the proper installation position is in
the place where it is very secluded.
To remove a disc magazine from the
changer, pull the handle towards you and
pull the magazine from the changer.
5
<DRC1107>
En
SPECIFICATIONS
Maximum number of discs
Operating temperature
Operating humidity
Storage temperature
Weight
50 discs
+5°C +35°C
5 - 85% (no condensation)
–40°C + 60°C
1,5 kg
External dimensions
184.8 (W) x 156.3 (H) x 173 (D)
NOTE:
Specifications and design subject to possible modifications without notice, due to improvements.
6
<DRC1107>
En
AFTER-SALES SERVICE FOR PIONEER PRODUCTS
Please contact the dealer or distributor from where you purchased the product for its after-
sales service (including warranty conditions) or any other information. In case the necessary
information is not available, please contact the Pioneer’s subsidiaries (regional service
headquarters) listed below:
PLEASE DO NOT SHIP YOUR PRODUCT TO THE COMPANIES
at the addresses listed below for repair without advance contact, for these companies are
not repair locations.
AMERICA
PIONEER ELECTRONICS SERVICE, INC.
CUSTOMER SUPPORT DIVISION
P.O. BOX 1760, LONG BEACH, CA 90801-1760, U.S.A.
EUROPE
PIONEER ELECTRONIC (EUROPE) N.V.
EUROPEAN SERVICE DIVISION
HAVEN 1087, KEETBERGLAAN 1, 9120 MELSELE, BELGIUM
ASEAN
PIONEER ELECTRONICS ASIACENTRE PET. LTD.
SERVICE DEPARTMENT
501 ORCHARD ROAD, #10-00
WHEELOCK PLACE, SINGAPORE 238880
JAPAN AND OTHERS
PIONEER ELECTRONIC CORPORATION (HEAD OFFICE)
CUSTOMER SUPPORT CENTER
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654 JAPAN
France : tapez 36 15 PIONEER
この取扱説明書はエコマーク認定
の再生紙を使用しています。
を
Published by Pioneer Electronic Corporation.
Copyright © 1999 Pioneer Electronic Corporation.
All rights reserved.
C 1999 パイオニア株式会社 禁無断転載
153-8654 東京都目黒区目黒１丁目４番１号
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
Business System Company: 15-5, Ohmorinishi 4-Chome, Ohta-ku, Tokyo 143-8564 Japan TEL: 81-3-3763-2369
PIONEER NEW MEDIA TECHNOLOGIES, INC.
Laser Optical Systems Division: 2265 East 220th Street, Long Beach, CA 90810, U.S.A. TEL: 1-310-952-2111
PIONEER ELECTRONIC [EUROPE] N.V.
PIONEER House, Hollybush Hill, STOKE POGES, SLOUCH SL2 4QP U.K. TEL: 44-1753-789-789
PIONEER ELECTRONICS OF CANADA, INC.
Industrial Products Department: 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 905-479-4411
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: 61-3-9586-6300
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
501 Orchard Road, #10-00, Wheelock Place, Singapore 238880 TEL: 65-735-9011
<99E00SF0M00>
Printed in Japan/Imprimé au Japon <DRC1107-A>
|