Subwoofer Manual
Manuel de subwoofer
Models: SL10d4, SL10d2, SL12d4, SL12d2
Features
Caractéristiques
• Reinforced Injection Molded Cone
• Die Cast Aluminum Heatsink Spider Spacer
• Vented Cone Neck Stabilizer
• Renforcé moulé par injection cone
• Aluminium moulé dissipateur thermique spider spacer
• Stabilisateur d’évent cou cone
• Non-Linear Roll Spider
• High Temperature OFC Voice Coils
• Rigid Stamped Steel Frame
• Anneau de centrage plat à excursion non-linéaire
• Bobines acoustiques en cuivre exempt d’oxygène à haute température
• Panier rigide en acier
• Nickel Plated 12 Gauge Speaker Terminals
• High Excursion Motor Design
• Bornes d’enceinte nickelées de calibre 12
• Modèle de moteur à grand battement
Subwoofer Owner’s Manual
system diagrams
Dual 4 ohm Subwoofer
(wired in parallel)
SL12d4 SINGLE SUBWOOFER
SYSTEM
R250.1/R500.1 + (1) SL12d4
+
-
+
-
All voice coils are wired in parallel for 2 ohm load.
R250.1 and R500.1 make maximum power into 2 ohm load.
Toutes les bobines mobiles sont câblées en parallèle de 2
Ohms. R250.1 et R500.1 faire puissance maximale en 2 Ohms.
Dual 4 ohm Subwoofers
(wired in parallel)
SL12d4 DUAL SUBWOOFER
SYSTEM
R1000.1/SD600.1/S1000.1 + (2) SL12d4
+
-
+ +
+
-
All voice coils are wired in parallel for 1 ohm load.
Amplifier makes maximum power into 1 ohm load.
-
-
Toutes les bobines mobiles sont câblées en
parallèle pour 1 Ohms. R1000.1/SD600.1/S1000.1
rend la puissance maximale de charge en 1 ohm.
Dual 2 ohm Subwoofer
(wired in series)
SL12d2 FOUR CHANNEL
SYSTEM
R500.4 + R65CX 4 ohm stereo front
and SL12d2 4 ohm bridged rear
+
-
+
-
R500.4 makes maximum power into a 4 ohm
bridged load. Subwoofer is dual 2 ohm and wired in
series for a final load of 4 ohm.
R500.4 faire puissance maximale en 4 ohm charge
comblé.
-
-
Note: S400.4, Ti600.4, SD500.4 can be substituted
for R500.4 in this system. System wiring is similiar.
+
+
Specifications
T/S Parameters: SL10d2
SL10d4
1.55
SL12d2
.8
SL12d4
1.55
Re (Dcr)
FS (Hz)
Sd (SqM)
BL TM
.83
34.1
35.9
33.9
32.9
.035
.035
.053
.053
6.43
8.08
6.62
8.41
Qms
5.18
4.94
5.61
4.4
Qes
.61
.69
.75
.79
Qts
.54
.6
.66
.67
Vas (liters)
Cms (uM/N)
Mms (gms)
SPL
26.33
154.55
140.94
90dB
Dual 2
26.16
153.58
128.29
90dB
Dual 4
45.92
114.72
192.54
90dB
Dual 2
53.29
133.13
175.39
90dB
Dual 4
Impedance
Specifications:
SL10d4/2
300 watts
600 watts
25mm
SL12d4/2
RMS Power Handling
PEAK Power Handling
Xmax (Peak to Peak)
Mounting Diameter
300 watts
600 watts
25mm
9in - 230mm
3.6in - 93mm
11in - 280mm
4in - 103mm
Mounting Depth
*Specifications subject to change
Phoenix Gold
A Division of AAMP of America™
13190 56th Court
Clearwater, Florida 33760
P: 866-788-4237
© 2011 AAMP of Florida, Inc
Designed and Engineered in the USA
LIMITED WARRANTY
Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This
warranty is not transferable and applies only to the original purchaser from an authorized Phoenix Gold dealer in the United States of America only. Should
service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Phoenix Gold will (at its discretion), repair or replace the
defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse,
product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not
cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear
and tear is not covered under warranty.
INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by that country’s Authorized Phoenix Gold reseller and not by Phoenix Gold.
Consumers needing service or warranty information for these products must contact that country’s reseller for information.
|