INTEGRATED CIRCUITS
DATA SHEET
TDA8543
2 W BTL audio amplifier
1997 Jun 12
Product specification
File under Integrated Circuits, IC01
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
BLOCK DIAGRAM
handbook, halfpage
TDA8543
−
11
6
OUT−
IN−
−
+
5
IN+
R
12
V
R
CC
−
−
+
14
20 kΩ
OUT+
4
3
SVR
20 kΩ
MODE
STANDBY/MUTE LOGIC
13
GND
MGK402
Fig.1 Block diagram.
PINNING
SYMBOL
PIN
DESCRIPTION
not connected
n.c.
1
2
3
n.c.
not connected
handbook, halfpage
MODE
operating mode select
n.c.
n.c.
1
2
3
4
5
6
7
8
16
n.c.
(standby, mute, operating)
15
14
13
12
11
10
9
n.c
SVR
4
half supply voltage, decoupling
ripple rejection
MODE
SVR
IN+
OUT+
GND
IN+
5
6
positive input
TDA8543
IN−
n.c.
negative input
V
CC
7
not connected
IN−
OUT−
n.c.
n.c.
8
not connected
n.c.
n.c.
9
not connected
n.c
n.c.
n.c.
10
11
12
13
14
15
16
not connected
MGK401
OUT−
VCC
GND
OUT+
n.c.
negative loudspeaker terminal
supply voltage
ground
positive loudspeaker terminal
not connected
Fig.2 Pin configuration.
n.c.
not connected
1997 Jun 12
3
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
The voltage loss on the positive supply line is
FUNCTIONAL DESCRIPTION
the saturation voltage of a PNP power transistor,
on the negative side the saturation voltage of an
NPN power transistor.
The TDA8543(T) is a BTL audio power amplifier capable
of delivering an output power between 1 and 2 W,
depending on supply voltage, load resistance
and package. Using the MODE pin the device can
be switched to standby and mute condition. The device
is protected by an internal thermal shutdown protection
mechanism.
Mode select pin
The device is in standby mode (with a very low current
consumption) if the voltage at the MODE
pin is >(VCC − 0.5 V), or if this pin is floating. At a MODE
voltage level of less than 0.5 V the amplifier is fully
operational.
The gain can be set within a range from 6 dB to 30 dB
by external feedback resistors.
In the range between 1.5 V and VCC − 1.5 V the amplifier
is in mute condition. The mute condition is useful to
suppress plop noise at the output, caused by charging of
the input capacitor.
Power amplifier
The power amplifier is a Bridge Tied Load (BTL) amplifier
with a complementary PNP-NPN output stage.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
VCC
PARAMETER
supply voltage
CONDITIONS
MIN.
−0.3
MAX.
+18
UNIT
operating
V
VI
input voltage
−0.3
−
−55
−40
−
VCC + 0.3
1
V
IORM
Tstg
Tamb
Vpsc
Ptot
repetitive peak output current
storage temperature
A
non-operating
+150
+85
10
°C
°C
V
operating ambient temperature
AC and DC short-circuit safe voltage
total power dissipation
SO16
DIP16
−
−
1.2
W
W
2.2
QUALITY SPECIFICATION
In accordance with “SNW-FQ-611-E”. The number of the quality specification can be found in the “Quality Reference
Handbook”. The handbook can be ordered using the code 9397 750 00192.
THERMAL CHARACTERISTICS
SYMBOL
Rth j-a
PARAMETER
CONDITIONS
in free air
VALUE
UNIT
thermal resistance from junction to ambient
TDA8543T (SO16)
100
55
K/W
K/W
TDA8543 (DIP16)
1997 Jun 12
4
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
MGK410
2.5
handbook, halfpage
P
(W)
2.0
1.5
1
(1)
(2)
0.5
0
0
40
80
120
T
160
(°C)
amb
(1) DIP16.
(2) SO16.
Fig.3 Power derating curve.
Table 1
CONTINUOUS SINE WAVE DRIVEN
V
CC (V)
RL (Ω)
Po (W)(1)
Tamb(max) (°C)
Pmax (W)
SO16
DIP16
5
7.5
7.5
9
8
1.2
2.2
1.4
2.0
1.3
0.7
1.6
0.9
1.3
0.9
80
−
60
−
112
62
8
16
16
25
100
78
9
60
100
Note
1. At THD = 10%; BTL.
1997 Jun 12
5
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
DC CHARACTERISTICS
VCC = 5 V; Tamb = 25 °C; RL = 8 Ω; VMODE = 0 V; G = 20 dB; measured in test circuit Fig.4; unless otherwise specified.
SYMBOL
VCC
PARAMETER
supply voltage
CONDITIONS
MIN.
2.2
TYP.
MAX.
18
UNIT
operating
5
8
−
V
Iq
quiescent current
standby current
DC output voltage
RL = ∞; note 1
VMODE = VCC
note 2
−
−
−
−
−
0
12
10
−
50
500
0.5
mA
µA
V
Istb
VO
2.2
−
VOUT+ − VOUT− differential output voltage offset
mV
nA
V
I
IN+, IIN−
input bias current
−
−
−
VMODE
input voltage mode select
operating
mute
1.5
VCC − 1.5 V
standby
VCC − 0.5
−
−
−
VCC
20
V
IMODE
input current mode select
0 < VMODE < VCC
µA
Notes
1. With a load connected at the outputs the quiescent current will increase, the maximum of this increase being equal
to the DC output offset voltage divided by RL.
2. The DC output voltage with respect to ground is approximately 0.5 × VCC
.
AC CHARACTERISTICS
VCC = 5 V; Tamb = 25 °C; RL = 8 Ω; f = 1 kHz; VMODE = 0 V; G = 20 dB; measured in test circuit Fig.4; unless otherwise
specified.
SYMBOL
PARAMETER
output power
CONDITIONS
THD = 10%;
VCC = 5 V; RL = 8 Ω
MIN.
TYP.
MAX.
UNIT
Po
1
1.2
−
W
V
CC = 7.5 V; RL = 8 Ω
−
−
2.2
2.0
−
−
W
W
VCC = 9 V; RL = 16 Ω
THD = 0.5%;
VCC = 5 V; RL = 8 Ω
0.6
−
−
−
6
0.9
1.7
1.4
0.15
−
100
−
−
−
−
−
0.3
30
−
100
−
W
VCC = 7.5 V; RL = 8 Ω
W
VCC = 9 V; RL = 16 Ω
W
THD
Gv
total harmonic distortion
closed loop voltage gain
differential input impedance
noise output voltage
Po = 0.5 W
note 1
%
dB
kΩ
µV
dB
dB
µV
Zi
−
−
50
40
−
Vno
note 2
note 3
note 4
SVRR
supply voltage ripple rejection
−
−
−
200
Vo
output voltage in mute condition note 5
1997 Jun 12
6
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
Notes to the AC characteristics
R2
R1
1. Gain of the amplifier is 2 ×
in test circuit of Fig.4.
-------
2. The noise output voltage is measured at the output in a frequency range from 20 Hz to 20 kHz (unweighted), with
a source impedance of RS = 0 Ω at the input.
3. Supply voltage ripple rejection is measured at the output, with a source impedance of RS = 0 Ω at the input.
The ripple voltage is a sine wave with a frequency of 1 kHz and an amplitude of 100 mV (RMS), which is applied
to the positive supply rail.
4. Supply voltage ripple rejection is measured at the output, with a source impedance of RS = 0 Ω at the input.
The ripple voltage is a sine wave with a frequency between 100 Hz and 20 kHz and an amplitude of 100 mV (RMS),
which is applied to the positive supply rail.
5. Output voltage in mute position is measured with an input voltage of 1 V (RMS) in a bandwidth of 20 kHz, so including
noise.
TEST AND APPLICATION INFORMATION
Test conditions
SE application
Tamb = 25 °C if not specially mentioned, VCC = 7.5 V,
f = 1 kHz, RL = 4 Ω, Gv = 20 dB, audio band-pass
22 Hz to 22 kHz.
Because the application can be either Bridge Tied Load
(BTL) or Single-Ended (SE), the curves of each application
are shown separately.
The SE application diagram is shown in Fig.14.
The capacitor value of C3 in combination with the load
impedance determines the low frequency behaviour.
The total harmonic distortion as a function of frequency
was measured with low-pass filter of 80 kHz. The value
of capacitor C2 influences the behaviour of the SVRR
at low frequencies, increasing the value of C2 increases
the performance of the SVRR.
The thermal resistance = 55 K/W for the DIP16 envelope;
the maximum sine wave power dissipation
for Tamb = 25 °C is:
150 – 25
= 2.27 W
----------------------
55
For Tamb = 60 °C the maximum total power dissipation is:
150 – 60
= 1.63 W
----------------------
General remark
55
The frequency characteristic can be adapted
by connecting a small capacitor across the feedback
resistor. To improve the immunity of HF radiation in radio
circuit applications, a small capacitor can be connected
in parallel with the feedback resistor; this creates a
low-pass filter.
See the power derating curve illustrated in Fig.3.
BTL application
T
amb = 25 °C if not specially mentioned, VCC = 5 V,
f = 1 kHz, RL = 8 Ω, Gv = 20 dB, audio band-pass
22 Hz to 22 kHz.
The BTL application diagram is shown in Fig.4.
The quiescent current has been measured without
any load impedance. The total harmonic distortion
as a function of frequency was measured with a low-pass
filter of 80 kHz. The value of capacitor C2 influences
the behaviour of the SVRR at low frequencies, increasing
the value of C2 increases the performance of the SVRR.
The figure of the mode select voltage (Vms) as a function
of the supply voltage shows three areas; operating, mute
and standby. It shows, that the DC-switching levels
of the mute and standby respectively depends
on the supply voltage level.
1997 Jun 12
7
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
BTL APPLICATION
V
CC
100 µF
R2
R1
56 kΩ
100 nF
12
C1
−
+
IN
6
5
4
3
−
+
OUT
OUT
11
14
11 kΩ
1 µF
IN
R
V
TDA8543
L
SVR
in
MODE
C2
47 µF
13
GND
MGK403
R2
Gain = 2 × -------
R1
Fig.4 BTL application.
MGD876
MGK404
10
15
handbook, halfpage
handbook, halfpage
I
q
THD
(%)
(mA)
(1)
(3) (2)
10
1
−1
5
10
−2
0
0
10
−2
−1
4
8
12
16
20
(V)
10
10
1
10
P
o
(W)
V
CC
f = 1 kHz, Gv = 20 dB.
(1) VCC = 5 V, RL = 8 Ω.
(2) VCC = 7.5 V, RL = 8 Ω.
(3) VCC = 9 V, RL = 16 Ω.
RL = ∞.
Fig.5 Iq as a function of VCC
.
Fig.6 THD as a function of Po.
1997 Jun 12
8
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
MGD879
MGK409
10
−20
handbook, halfpage
handbook, halfpage
SVRR
(dB)
THD
(%)
−40
1
(1)
(1)
(3)
(2)
(3)
(2)
−1
10
−60
−2
−80
10
2
3
4
5
2
3
5
4
10
10
10
10
10
10
10
10
10
10
f (Hz)
f (Hz)
Po = 0.5 W, Gv = 20 dB.
(1) VCC = 5 V, RL = 8 Ω.
(2) VCC = 7.5 V, RL = 8 Ω.
(3) VCC = 9 V, RL = 16 Ω.
VCC = 5 V, 8 Ω, Rs = 0 Ω, Vr = 100 mV.
(1) Gv = 30 dB.
(2) Gv = 20 dB.
(3) Gv = 6 dB.
Fig.7 THD as a function of frequency.
Fig.8 SVRR as a function of frequency.
MGK406
MGK405
2
2.5
handbook, halfpage
handbook, halfpage
P
o
P
(W)
2
(W)
1.5
1
(1)
(2)
1.5
1
(1)
(2)
(3)
(3)
0.5
0.5
0
0
0
0
4
8
12
4
8
12
V
(V)
V
(V)
CC
CC
THD = 10%.
(1) RL = 8 Ω.
(2) RL = 16 Ω.
(3) RL = 25 Ω.
(1) RL = 8 Ω.
(2) RL = 16 Ω.
(3) RL = 25 Ω.
Fig.10 Worst case power dissipation as a function
of VCC
Fig.9 Po as a function of VCC
.
.
1997 Jun 12
9
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
MGK407
MGD883
2
10
o
handbook, halfpage
handbook, halfpage
V
P
(W)
(V)
1
(3)
(1)
1.6
−1
10
1.2
0.8
0.4
0
−2
10
(1)
(2) (3)
−3
10
(2)
−4
10
−5
10
−6
10
−1
2
10
1
10
10
0
0.5
1
1.5
2
2.5
V
(V)
P
(W)
ms
o
Sine wave of 1 kHz.
Band-pass = 22 Hz to 22 kHz.
(1) VCC = 3 V.
(1) VCC = 9 V, RL = 16 Ω.
(2) VCC = 5 V, RL = 8 Ω.
(3) VCC = 7.5 V, RL = 8 Ω.
(2) VCC = 5 V.
(3) VCC = 12 V.
Fig.11 P as a function of Po.
Fig.12 Vo as a function of Vms.
MGL070
16
handbook, halfpage
V
ms
(V)
12
standby
8
4
mute
operating
12 16
0
0
4
8
V
(V)
P
Fig.13 Vms as a function of VP.
1997 Jun 12
10
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
SE APPLICATION
V
CC
100 µF
R2 110 kΩ
100 nF
C3
12
C1
R1
−
+
IN
6
5
4
3
11 kΩ
1 µF
−
+
OUT
OUT
IN
11
14
V
TDA8543
SVR
470 µF
in
R
L
MODE
C2
47 µF
13
GND
MGK408
R2
-------
R1
Gain =
Fig.14 SE application.
MGD885
MGD884
10
10
handbook, halfpage
handbook, halfpage
THD
(%)
THD
(%)
1
1
(1)
(1)
(2)
(3)
−1
−1
10
10
(2)
(3)
−2
−2
10
10
−2
−1
2
3
4
5
10
10
1
10
10
10
10
10
10
f (Hz)
P
(W)
o
f = 1 kHz, Gv = 20 dB.
Po = 0.5 W, Gv = 20 dB.
(1) VCC = 7.5 V, RL = 4 Ω.
(2) VCC = 9 V, RL = 8 Ω.
(3) VCC = 12 V, RL = 16 Ω.
(1) VCC = 7.5 V, RL = 4 Ω.
(2) VCC = 9 V, RL = 8 Ω.
(3) VCC = 12 V, RL = 16 Ω.
Fig.15 THD as a function of Po.
Fig.16 THD as a function of frequency.
1997 Jun 12
11
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
MGD886
MGD887
−20
2
handbook, halfpage
handbook, halfpage
P
o
(W)
1.6
SVRR
(dB)
−40
(3)
(1)
(2)
1.2
0.8
(1)
(2)
−60
(3)
0.4
−80
0
0
2
3
4
5
10
10
10
10
10
4
8
12
16
f (Hz)
V
(V)
CC
VCC = 7.5 V, RL = 4 Ω, Rs = 0 Ω, Vi = 100mV.
(1) Gv = 24 dB.
(1) THD = 10%, RL = 4 Ω.
(2) THD = 10%, RL = 8 Ω.
(3) THD = 10%, RL = 16 Ω.
(2) Gv = 20 dB.
(3) Gv = 0 dB.
Fig.17 SVRR as a function of frequency.
Fig.18 Po as a function of VCC.
MGD889
MGD888
1.2
1.6
handbook, halfpage
handbook, halfpage
P
(1)
(2)
P
(W)
(W)
1.2
0.8
0.4
0.8
0.4
(3)
(1)
(2)
(3)
0
0
0
0
0.4
0.8
1.2
1.6
4
8
12
16
P
(W)
V
(V)
o
CC
(1) RL = 4 Ω.
(2) RL = 8 Ω.
(3) RL = 16 Ω.
(1) VCC = 7.5 V, RL = 4 Ω.
(2) VCC = 12 V, RL = 16 Ω.
(3) VCC = 9 V, RL = 8 Ω.
Fig.19 Worst case power dissipation as a function
of VCC
Fig.20 P as a function of Po.
.
1997 Jun 12
12
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
a. Top view.
10 kΩ
10 kΩ
MS
16
1
TDA8543
IN
1 µF
11 kΩ
+
OUT
8
9
56 kΩ
−
OUT
47 µF
100 nF
100 µF
+
V
P
MGK411
b. Component side.
Fig.21 Printed-circuit board layout (BTL and SE).
13
1997 Jun 12
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
PACKAGE OUTLINES
DIP16: plastic dual in-line package; 16 leads (300 mil); long body
SOT38-1
D
M
E
A
2
A
A
1
L
c
e
w M
Z
b
1
(e )
1
b
16
9
M
H
pin 1 index
E
1
8
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
(1)
Z
A
A
A
(1)
(1)
1
2
w
UNIT
mm
b
b
c
D
E
e
e
L
M
M
H
1
1
E
max.
max.
min.
max.
1.40
1.14
0.53
0.38
0.32
0.23
21.8
21.4
6.48
6.20
3.9
3.4
8.25
7.80
9.5
8.3
4.7
0.51
3.7
2.54
0.10
7.62
0.30
0.254
0.01
2.2
0.021
0.015
0.013
0.009
0.86
0.84
0.32
0.31
0.055
0.045
0.26
0.24
0.15
0.13
0.37
0.33
inches
0.19
0.020
0.15
0.087
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
92-10-02
95-01-19
SOT38-1
050G09
MO-001AE
1997 Jun 12
14
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1
D
E
A
X
c
y
H
v
M
A
E
Z
16
9
Q
A
2
A
(A )
3
A
1
pin 1 index
θ
L
p
L
1
8
e
w
M
detail X
b
p
0
2.5
scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
(1)
(1)
(1)
UNIT
A
A
A
b
c
D
E
e
H
L
L
p
Q
v
w
y
Z
θ
1
2
3
p
E
max.
0.25
0.10
1.45
1.25
0.49
0.36
0.25
0.19
10.0
9.8
4.0
3.8
6.2
5.8
1.0
0.4
0.7
0.6
0.7
0.3
mm
1.27
0.050
1.05
0.041
1.75
0.25
0.01
0.25
0.01
0.25
0.1
8o
0o
0.010 0.057
0.004 0.049
0.019 0.0100 0.39
0.014 0.0075 0.38
0.16
0.15
0.244
0.228
0.039 0.028
0.016 0.020
0.028
0.012
inches
0.069
0.01 0.004
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
EIAJ
95-01-23
97-05-22
SOT109-1
076E07S
MS-012AC
1997 Jun 12
15
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
SOLDERING
Introduction
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
WAVE SOLDERING
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
DIP
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
SOLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
• The package footprint must incorporate solder thieves at
the downstream end.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
REPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
1997 Jun 12
16
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
DEFINITIONS
Data sheet status
Objective specification
Preliminary specification
Product specification
This data sheet contains target or goal specifications for product development.
This data sheet contains preliminary data; supplementary data may be published later.
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1997 Jun 12
17
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
NOTES
1997 Jun 12
18
Philips Semiconductors
Product specification
2 W BTL audio amplifier
TDA8543
NOTES
1997 Jun 12
19
Philips Semiconductors – a worldwide company
Argentina: see South America
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Belgium: see The Netherlands
Brazil: see South America
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Portugal: see Spain
Romania: see Italy
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Colombia: see South America
Slovakia: see Austria
Czech Republic: see Austria
Slovenia: see Italy
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 1949
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580/xxx
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2870, Fax. +886 2 2134 2874
Indonesia: see Singapore
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,
Tel. +972 3 645 0444, Fax. +972 3 649 1007
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Uruguay: see South America
Vietnam: see Singapore
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
Middle East: see Italy
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Internet: http://www.semiconductors.philips.com
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
© Philips Electronics N.V. 1997
SCA53
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
547027/50/01/pp20
Date of release: 1997 Jun 12
Document order number: 9397 750 02232
|