Philips Headphones SHB9150 User Manual

Always there to help you  
Register your product and get support at  
SHB9150  
Question?  
Contact  
Philips  
User manual  
 
Caution  
1 Important safety  
instructions  
Do not expose the headset to excessive heat.  
Do not drop your headset.  
Headset shall not be exposed to dripping or splashing.  
Do not allow your headset to be submerged in water.  
Do not use any cleaning agents containing alcohol,  
ammonia, benzene, or abrasives.  
If cleaning is required use a soft cloth, if necessary  
dampened with a minimum amount of water or diluted  
mild soap, to clean the product.  
The integrated battery shall not be exposed to  
excessive heat such as sunshine, fire or the like.  
Hearing Safety  
About operating and storage temperatures  
and humidity  
Operate or store in a place where  
temperature is between -15ºC (5ºF) and  
55ºC (131ºF) (up to 90% relative humidity.  
Battery life may be shorter in high or low  
temperature conditions.  
Danger  
To avoid hearing damage, limit the time you use the  
headset at high volume and set the volume to a safe  
level.The louder the volume, the shorter the safe  
listening time is.  
Be sure to observe the following guidelines  
when using your headset.  
Compliance with EMF  
Listen at reasonable volumes for  
reasonable periods of time.  
This product complies with all applicable  
standards and regulations regarding exposure to  
electromagnetic fields.  
Be careful not to adjust the volume  
continuously upwards as your hearing  
adapts.  
Do not turn up the volume so high that  
you can’t hear what’s around you.  
You should use caution or temporarily  
discontinue use in potentially hazardous  
situations.  
Excessive sound pressure from earphones  
and headset can cause hearing loss.  
Using the headset with both ears covered  
while driving is not recommended and may  
be illegal in some areas while driving.  
For your safety, avoid distractions from  
music or phone calls while in traffic or  
other potentially dangerous environments.  
General information  
To avoid damage or malfunction:  
2
EN  
 
       
2 Your Bluetooth  
stereo headset  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from the  
support that Philips offers, register your product  
With this Philips wireless on-ear headset, you  
can:  
Quick start guide  
Other devices  
A mobile phone or device (e.g. notebook, PDA,  
Bluetooth adapters, MP3 players etc) which  
supports Bluetooth and is compatible to the  
headset.  
enjoy convenient wireless handsfree calls;  
enjoy and control wireless music;  
switch between calls and music;  
enjoy music on non-Bluetooth devices with  
an audio cable.  
Overview of your Bluetooth  
stereo headset  
What's in the box  
a
Philips Bluetooth stereo headset SHB9150  
e
d
b
c
a
Call/Music button  
USB charging cable  
b Microphone  
c Audio input jack  
d Charging slot  
e Volume/Track control  
Audio cable  
EN  
3
 
       
Manual pairing  
NFC pairing  
3 Get started  
Manual pairing  
1 Make sure that the mobile phone is turned  
Charge your headset  
on and its Bluetooth feature is activated.  
2 Make sure that the headset is fully charged  
Note  
and turned off.  
Before you use your headset for the first time, charge  
the battery for 5 hours for optimum battery capacity  
and lifetime.  
Use only the original USB charging cable to avoid any  
damage.  
3 Press and hold until the blue and white  
LED flashes alternately.  
» The headset remains in pairing mode  
for 5 minutes.  
Finish your call before charging the headset, as  
connecting the headset for charging will power the  
headset off.  
4 Pair the headset with the mobile phone.  
For detailed information, refer to the user  
manual of your mobile phone.  
Connect the supplied USB charging cable to:  
the USB connector of the headset and;  
USB power source.  
NFC pairing  
» LED turns white during charging and  
turns off when the headset is fully  
charged.  
1 Make sure that the mobile phone is turned  
on.  
2 Make sure that the headset is fully charged  
and turned off.  
3 Press and hold until the blue and white  
Tip  
LED flashes alternately..  
Normally, a full charge takes 3 hours.  
When your battery is empty, you can carry on listening  
music with an audio cable. Make sure the headset is off  
(and not in idle mode) before using this audio cable.  
4 Make sure you turn on the NFC function  
on your phone and your phone’s screen  
remains active.  
5 Place your phone over the headset so that  
the NFC detection area of each device can  
touch each other.  
Pair the headset with your  
mobile phone  
Note  
Make sure your mobile phone has the NFC feature  
available and switched on.  
Make sure your mobile phone is not in standby mode.  
Pairing with NFC is only suitable for Android mobile  
operating system 4.2 or above.  
Before you use the headset with your mobile  
phone for the first time, pair it with a mobile  
phone.A successful pairing establishes a unique  
encrypted link between the headset and mobile  
phone.The headset stores the last 8 devices  
in the memory. If you try to pair more than 8  
devices, the earliest paired device is replaced by  
the new one.  
Refer to the user manual of your mobile phone to  
identify its NFC detection area.  
There are two ways to pair your headset with  
your mobile phone:  
4
EN  
 
     
The following example shows you how to pair  
the headset with your mobile phone.  
1 Activate the Bluetooth feature of your  
mobile phone, select Philips SHB9150.  
2 Enter the headset password "0000" (4  
zeros) if prompted. For those mobile  
phones featuring Bluetooth 3.0 or higher,  
no need to enter a password.  
10:35  
10:36  
10:37  
Settings  
Connectivity  
Settings  
Settings  
Connectivity  
Bluetooth  
Devices Found  
Enter Password  
****  
Add  
Bluetooth  
device  
Philips SHB9150  
0000  
Select  
Back  
Select  
Back  
Select  
Back  
EN  
5
 
4 Use your  
headset  
Manage your calls and music  
Call/Music button  
Task  
Operation Sound or LED  
indicator  
Connect the headset to a  
Bluetooth device  
Turn the  
headset on. hold for 1  
second.  
Press and  
1 short beep  
• 3 white flashes:  
battery low <  
25%  
1 Turn on your mobile phone/Bluetooth  
device.  
• 2 white flashes:  
battery level <  
50%  
2 Press and hold to turn the headset on.  
» The blue LED flashes.  
• 1 blue flash:  
battery level >  
50%  
1 long beep  
1 long white  
flash  
» The headset is reconnected to  
the last connected mobile phone/  
Bluetooth device automatically. If the  
last one is not available, the headset  
tries to reconnect to the second last  
connected device.  
Turn the  
headset off. hold for 4  
seconds.  
Press and  
Play or  
Press once. 1 short beep  
pause  
music.  
Tip  
Pick up/  
hang up a  
call.  
Press once. 1 short beep  
If you turn on the mobile phone/Bluetooth device or  
activate the Bluetooth feature after turning on the  
headset, you have to reconnect the headset and mobile  
phone/Bluetooth device manually.  
Reject an  
incoming  
call.  
Press and  
hold for 1  
second.  
1 short beep  
Note  
Redial the  
last number.  
Switch  
Press twice. 1 short beep  
If the headset fails to connect to any Bluetooth device  
within range in 5 minutes, it will switch off automatically  
to save the battery life.  
Press 1 long beep  
caller during twice.  
a call.  
Volume/Track control button  
Automatic power saving  
Adjust volume.  
Skip forward.  
Skip backward.  
Slide up/  
down  
Press once 1 short  
beep  
Press twice 1 short  
beep  
N/A  
If the headset fails to connect any  
Bluetoothdevice within range in 5 minutes, it  
powers down automatically to save the battery  
life.  
Mute/unmute the  
microphone in a call.  
Press  
once  
2 short  
beeps  
6
EN  
 
       
Other headset indicator status  
Use with the audio cable  
Headset status  
Indicator  
Blue LED flashes  
The headset is connected  
Note  
to a Bluetooth device, while for every 8  
Make sure that you turn off the Bluetooth headset  
the headset in standby  
mode or while you are  
listening to music.  
The headset is ready for  
pairing.  
seconds.  
before connecting the audio cable.  
With the supplied audio cable, you can use  
the headset with non-Bluetooth devices or on  
airplane. No battery power is required for the  
headset when you use it with the audio cable.  
Connect the supplied audio cable to  
LED flashes  
blue and white  
alternately.  
The headset is on but not  
connected to a Bluetooth  
device.  
Blue LED flashes  
quickly.  
the headset and;  
an external audio device.  
There is an incoming call.  
Blue LED flashes  
once per second.  
White LED  
Low battery.  
flashes.  
Battery is fully charged.  
White LED is off.  
Wear your headset  
Adjust the headband for the best fit.  
Tip  
After use, twist both earshells, fold the headset flat for  
storage.  
EN  
7
 
   
5 Technical data  
Up to 9 hours of music time or talk time  
Up to 200 hours of standby time  
Normal time for a full charge: 3 hours  
Rechargeable Lithium-Polymer battery  
(230 mAh)  
3.5 mm audio jack for corded headset  
mode  
Bluetooth 2.1 EDR, Bluetooth mono  
support (Headset Profile - HSP, Hands-  
Free Profile - HFP), Bluetooth stereo  
supported (Advanced Audio Distribution  
Profile - A2DP;AudioVideo Remote  
Control Profile - AVRCP)  
Operating range: Up to 15 meters (50  
feet)  
Digital echo & noise reduction  
Auto power off  
Note  
Specifications are subject to change without notice.  
8
EN  
 
 
6 Notice  
Your product contains batteries covered by the  
European Directive 2006/66/EC, which cannot  
be disposed with normal household waste.  
Please inform yourself about the local rules  
on separate collection of batteries because  
correct disposal helps to prevent negative  
consequences for the environmental and  
human health.  
Declaration of conformity  
Hereby,WOOX Innovations declares that this  
product is in compliance with the essential  
requirements and other relevant provisions  
of Directive 1999/5/EC.You can find the  
com.  
This product has been designed, tested and  
manufactured according the European R&TTE  
directive 1999/5/EC.  
Remove the integrated battery  
Note  
Make sure the headset is disconnected from the USB  
charging cable before removing the battery.  
Disposal of your old product  
and batteries  
If there is no collection/recycling system for  
electronic products in your country, you can  
protect the environment by removing and  
recycling the battery before disposing the  
headset.  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused.  
1
2
3
4
Environmental information  
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/  
EC. Please inform yourself about the local  
separate collection system for electrical and  
electronic products.  
All unnecessary packaging has been omitted.  
We have tried to make the packaging easy to  
separate into three materials: cardboard (box),  
polystyrene foam (buffer) and polyethylene  
(bags, protective foam sheet.)  
Your system consists of materials which can  
be recycled and reused if disassembled by  
a specialized company. Please observe the  
local regulations regarding the disposal of  
packaging materials, exhausted batteries and old  
equipment.  
Please act according to your local rules and  
do not dispose of your old products with your  
normal household waste.  
Correct disposal of your old product helps to  
prevent potential negative consequences for the  
environment and human health.  
EN  
9
 
     
Notice for the European  
Union  
0168  
Hereby,WOOX Innovations declares that this  
product is in compliance with the essential  
requirements and other relevant provisions of  
Directive 1999/5/EC.  
Trademarks  
2013 © WOOX Innovations Limited.All rights  
reserved.  
Philips and the Philips’ Shield Emblem are  
registered trademarks of Koninklijke Philips N.V.  
and are used by WOOX Innovations Limited  
under license from Koninklijke Philips N.V.  
Bluetooth  
The Bluetooth word mark and logos are owned  
by the Bluetooth SIG, Inc. and any use of such  
marks by WOOX Innovations Limited is under  
license.  
10 EN  
 
   
My Bluetooth headset is connected to a  
7 Frequently  
Bluetooth stereo enabled mobile phone, but  
music only plays on the mobile phone speaker.  
Refer to the user manual of your mobile phone.  
Select to listen to music through the headset.  
asked questions  
My Bluetooth headset does not switch on.  
The battery level is low. Charge the headset.  
The audio quality is poor and crackling noise  
can be heard.  
The Bluetooth device is out of range. Reduce  
the distance between your headset and  
Bluetooth device, or remove obstacles between  
them.  
I cannot pair my Bluetooth headset with a  
mobile phone.  
The Bluetooth is disabled. Enable the Bluetooth  
feature on your mobile phone and turn on the  
mobile phone before you turn on the headset.  
The audio quality is poor when streaming  
from the mobile phone is very slow, or audio  
streaming does not work at all.  
Make sure your mobile phone not only  
supports (mono) HSP/HFP but also supports  
A2DP.  
Pairing does not work.  
Make sure the headset is in pairing mode.  
manual (see 'Pair the headset with your  
mobile phone' on page 4).  
Make sure that the LED light flashes blue  
and white alternately before you release  
the call/music button. Do not stop holding  
the button if you see the blue LED only.  
I hear but cannot control music on my  
Bluetooth device (e.g. play/pause/skip forward/  
backward).  
Make sure the Bluetooth audio source supports  
AVRCP.  
The mobile phone cannot find the headset.  
The headset may be connected to a  
previously paired device.Turn off the  
connected device or move it out of range.  
Pairing may have been reset or the headset  
has been previously paired with another  
device. Pair the headset with the mobile  
phone again as described in the user  
manual (see 'Pair the headset with your  
mobile phone' on page 4).  
My headset does not work when the audio  
cable is connected.  
Microphone function will be deactivated if a  
3.5mm audio cable is connected to the headset.  
In such case, your headset is only for music  
enjoyment.  
How can I restore all original headset settings?  
Press volume/track control button and call  
music button until the LED flashing white for 5  
times sequentially.  
Voice dialing or redialing does not work on  
my mobile phone.  
Your mobile phone may not support this  
feature.  
support.  
The other side cannot hear me on the mobile  
phone.  
The microphone is muted. Press volume/track  
control button once to enable the microphone.  
EN 11  
 
 
2013 ©WOOX Innovations Limited.  
All rights reserved.  
Philips and the Philips’ Shield Emblem are registered  
trademarks of Koninklijke Philips N.V. and are used  
byWOOX Innovations Limited under license from  
Koninklijke Philips N.V.  
SHB9150_UM_V1.0  
wk1429  
 

Phase Technology Portable Speaker XT610 User Manual
Philips CD Player 190B6CS User Manual
Philips Clock Radio PDCC JW 0703 User Manual
Philips Home Theater System HES4900 User Manual
Philips Thermometer SBCSC550 User Manual
Polaroid Digital Camera Instant Digital Camera with Zero Ink Printing Technology User Manual
Polaroid DVD Player PDV 1002A User Manual
Praktica Digital Camera D00478 User Manual
Printek Network Card Mt3 II Series User Manual
PYLE Audio Fitness Equipment PFTL314041 User Manual