Philips DVD Player DVD622 051 User Manual

DVD  
DVD-622  
DVD-612  
Video Player  
 
General Information  
The region code for this set is 2.  
Laser safety  
2
Since it is usual for DVD movies to be released at  
different times in different regions of the world,  
all players have region codes and discs can have an optional  
region code. If you load a disc of a different region code to  
your player, you will see the region code notice on the  
screen.The disc will not playback, and should be unloaded.  
This unit employs a laser. Due to possible eye injury, only a  
qualified service person should remove the cover or  
attempt to service this device.  
USE OF CONTROLS OR ADJUSTMENTS OR  
PERFORMANCE OF PROCEDURES OTHER  
THANTHOSE SPECIFIED HEREIN MAY  
RESULT IN HAZARDOUS RADIATION  
EXPOSURE.  
NOTE:  
PICTURES SHOWN MAYBE DIFFERENT  
BETWEEN COUNTRIES.  
LASER  
Type  
Wave length  
Semiconductor laser GaAlAs  
650 nm (DVD)  
NEVER MAKE OR CHANGE CONNECTIONS  
WITHTHE POWER SWITCHED ON.  
780 nm (VCD/CD)  
7 mW (DVD)  
Output Power  
10 mW (VCD/CD)  
60 degree  
Beam divergence  
CAUTION  
(WARNING LOCATION: ONTHE BACKPLATE  
OF SET)  
Manufactured under license from Digital Theater Systems,  
Inc. US Pat. No. 5,451,942 and other world-wide patents  
issued and pending. “DTS” and “DTS DIGITAL SURROUND”  
are trademarks of Digital Theater Systems, Inc. © 1996  
Digital Theater Systems, Inc. All rights reserved.  
CAUTION  
VISIBLE AND INVISIBLE LASER RADIATION WHEN  
OPEN AVOID EXPOSURETO BEAM  
ADVARSEL  
SYNLIG OG USYNLIG LASERSTRÅLINGVED ÅBNING  
UNDGÅ UDSÆTTELSE FOR STRÅLING  
VARNING  
SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR  
DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN  
VARO!  
The DVD-VIDEO player is in conformity  
with the EMC directive and low-voltage  
directive.  
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA  
NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO  
SÄTEESEEN  
VORSICHT  
TruSurround and the SRS symbol are trademarks of SRS  
Labs., Inc.TruSurround technology is manufactured under  
license from SRS Labs., Inc.  
SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG  
WENN ABDECKUNG GEÖFFNET NICHT DEM  
STRAHL AUSSETSEN  
ATTENTION  
RAYONNEMENT LASERVISIBLE ET INVISIBLE EN CAS  
D’OUVERTURE EXPOSITION DANGEREUSE AU  
FAISCEAU  
For Customer Use:  
Read carefully the information located at the bottom of  
your DVD-VIDEO player and enter below the Serial  
No.Retain this information for future reference.  
Model No. DVD-VIDEO  
Serial No. __________________________  
3
GENERAL INFORMATION  
 
Contents  
Introduction  
Philips DVDVideo Introduction ------------------------- 5  
Unpacking ---------------------------------------------------- 5  
Remote Control Battery Installation ------------------- 5  
Environmental Information ------------------------------- 5  
Safety Information ------------------------------------------ 5  
Cleaning Discs ---------------------------------------------- 5  
Functional Overview  
Front and Rear Panels ------------------------------------- 6  
Remote Control -------------------------------------------- 7  
Preparation  
General Notes ---------------------------------------------- 8  
Connecting to aTV ---------------------------------------- 8  
Connecting to Optional Equipment-------------------8-9  
NTSC/PAL Settings----------------------------------------- 9  
NTSC/PAL Conversion------------------------------------ 9  
General Explanation --------------------------------------- 9  
Initial Setup -------------------------------------------------10  
Menu Bar/StatusWindow --------------------------------10  
Temporary Feedback Field Icons -----------------------11  
Personal Preferences----------------------------------11-12  
Operation  
Loading Discs-----------------------------------------------13  
Playing a DVDVideo andVideo CD Disc--------------13  
General Features --------------------------------------13-15  
Special DVD Features-------------------------------------15  
SpecialVCD & SVCD Features--------------------------16  
Playing an Audio CD --------------------------------------16  
FTS Programme----------------------------------------16-17  
MP3 Disc Features ----------------------------------------17  
Access Control  
Access Control: Child Lock -----------------------------18  
Access Control: Parental Control ------------------18-19  
Before Requesting Service  
Before Requesting Service -------------------------------20  
Specifications  
Specifications -----------------------------------------------21  
4
CONTENTS  
 
Introduction  
Philips DVD-Video  
Introduction  
Remote Control Battery  
Installation  
Your Philips DVD-Video player will playback digital video  
discs conforming to the universal DVD-Video standard.The  
unique features of DVD-Video, such as selection of sound  
track, subtitle languages and different camera angles (disc  
dependent), are all supported.  
Insert batteries as indicated inside the battery  
compartment.  
Caution: Do not mix old and new batteries. Never  
mix different types of batteries (standard, alkaline,  
etc.)  
In addition to DVD-Video discs, you will be able to playback  
allVideo CDs, SVCDs and Audio CDs.  
-
+
DVD-Video  
You will recognise DVD-Video discs by the logo shown.  
Depending on the material on the disc (a movie, video clips,  
a drama series, etc.) the disc may have one or moreTitles.  
+
-
DVD-VIDEO DISC  
TITLE 1  
TITLE 2  
CHAPTER 1 CHAPTER 2 CHAPTER 1 CHAPTER 2  
CHAPTER 3  
Environmental Information  
Your system consists of materials which can be recycled  
and reused if disassembled by a specialized company. Please  
observe the local regulations regarding the disposal of  
packaging materials, exhausted batteries and old equipment.  
Video CD  
You will recogniseVideo CDs by the logo  
shown.  
SuperVideo CD (SVCD)  
Safety Information  
Do not expose the system to excessive moisture, rain, sand  
or heat sources.  
Place the player on a firm, flat surface.  
Keep the player away from domestic heating equipment  
and direct sunlight.  
SVCD discs based on the SuperVCD IO Standard refering  
to Standard of Electronics Industry of the People’s Republic  
of China.  
Audio CD  
Audio CDs contain music tracks only.  
You will recognise Audio CDs by their logo  
shown.  
In a cabinet, allow about 2.5 cm (1 inch) of free space all  
around the player for adequate ventilation.  
If the DVD-Video player cannot read CDs/DVDs correctly,  
use a commonly available cleaning CD/DVD to clean the  
lens before taking the DVD-Video player to be repaired.  
Other cleaning methods may destroy the lens.Always keep  
the tray closed to avoid dust on the lens.  
MP3 (MPEG Audio Layer-3) (DVD622 only)  
This player supports MP3 which contains compressed  
music tracks.  
The lens may cloud over when the DVD-Video player is  
suddenly moved from cold to warm surroundings. Playing a  
CD/DVD is not possible then. Leave the power on for  
about one hour with no disc in the unit until normal  
playback is possible.  
Note:  
– Only the first session of multisession discs is supported  
Unpacking  
First check and identify the contents of your DVD-Video  
player package.  
You should have the following items.  
– DVD-Video player  
– Remote Control with batteries  
– Audio/Video cable  
– SCART cable  
Cleaning Discs  
When a disc becomes dirty, clean it with a cleaning cloth.  
Wipe the disc from the centre out, in a straight line.  
Do not use solvents such as benzine, thinner, commercially  
available cleaners, or anti-static spray intended for analog  
discs.  
– Instructions for use  
If any item is damaged or missing, contact your retailer or  
Philips.  
Keep the packaging materials for future transportation.  
5
INTRODUCTION  
 
Functional Overview  
Front and Rear Panels  
STANDBY-ON  
; PAUSE  
– switches the player to Standby mode or ON  
– to interrupt playback  
DISPLAY  
B PLAY  
– shows the current status of the player  
– to start playback  
9 STOP  
– to stop playback  
DVD622  
S PREV  
– go to previous chapter or track  
/ OPEN/CLOSE  
– opens/closes the disc tray  
SOUND  
– selects Stereo, Dolby Surround or  
3D Sound (TruSurround)  
Disc Tray  
T NEXT  
– go to next chapter or track  
TV OUT (TV)  
MAINS (AC Power)  
– connect to TV with SCART  
– connect to power source  
VIDEO OUT (CVBS)  
COAXIAL (Digital audio out jack)  
– connect to TV with CVBS video inputs  
– connect to digital (coaxial) equipment  
AUDIO OUT (Left/Right)  
– connect to amplifier, receiver or stereo  
system  
DIGITAL AUDIO OUT  
PCM-MPEG2-Dolby Digital-DTS  
TV OUT  
R
L
(CVBS)  
COAXIAL  
AUDIO OUT  
VIDEO OUT  
Caution: Do not touch the inner pins of the jacks on the rear panel connectors. Electrostatic discharge may  
cause permanent damage to the unit.  
6
FUNCTIONAL OVERVIEW  
 
Remote Control  
POWER B  
– switches DVD ON or to standby/  
on mode  
RETURN / RESUME  
– go back to previous menu / to  
continue playback after play  
was stop  
0-9 numerical key pad  
– to select numbered items in a  
menu  
DISC MENU  
– access menu of a DVD disc  
DISPLAY  
– displays bit rate indicator during  
playback  
1 2 3 4  
– (left/right/up/down) to select  
an item in the menu  
OK  
SYSTEM MENU  
– access or remove player’s system  
menu  
– acknowledge menu selection  
S
– search backward* / go to a  
previous chapter or track  
T
– search forward* / next chapter  
or track  
STOP ( 9 )  
– to stop playback  
SUBTITLE  
– subtitle language selector  
PLAY ( B )  
– to start playback  
ANGLE  
– select DVD camera angle  
PAUSE ( ; )  
– pause playback temporarily /  
frame-by-frame playback  
ZOOM  
– enlarge video image  
AUDIO  
– audio language selector  
REPEAT  
– repeat chapter, track, title, disc  
REPEAT (A-B)  
– repeat a specific segment  
SHUFFLE  
– playback tracks in random  
order  
SCAN  
– playback of the first 10 seconds  
of each track/chapter within a  
disc  
* Press key for about 2 seconds  
7
FUNCTIONAL OVERVIEW  
 
Preparation  
General Notes  
Connecting to Optional  
Equipment  
Depending on yourTV and other equipment you wish to  
connect, there are various ways you could connect the  
player. Use only one of the connections described below.  
Please refer to the manuals of yourTV,VCR, Stereo System  
or other devices as necessary to make the best  
connections.  
Connecting to an amplifier equipped with  
two channel analog stereo or Dolby  
Surround  
1 Connect the Left and Right AUDIO OUT jacks of the DVD  
player to the audio left and right in jacks on your amplifier,  
receiver or stereo system, using the supplied audio cable  
(A).  
For better sound reproduction, connect the player’s audio  
out jacks to the audio in jacks of your amplifier, receiver,  
stereo or A/V equipment. See ‘Connecting to optional  
equipment’.  
Note:  
Caution:  
– You cannot use the MP3 function with the digital out  
connectors.  
Make sure the DVD player is connected directly  
to theTV. Set theTV to the correct video input  
channel.  
Connecting to an amplifier equipped with  
two channel digital stereo (PCM) or to an  
A/V receiver equipped with a multi-channel  
decoder (Dolby Digital, MPEG 2 and  
DTS)  
Do not connect the players audio out jack to  
the phono in jack of your audio system.  
Do not connect your DVD-player via yourVCR.  
The DVD image could be distorted by the copy  
protection system.  
1 Connect the player’s digital audio out jack (coaxial F) to the  
corresponding in jack on your amplifier. Use an optional  
digital (coaxial F) audio cable.  
Connecting to a TV  
Make one of the following connections, depending on the  
capabilities of your existing equipment.  
2 You will need to activate the player’s digital output (see  
‘Personal Preferences’).  
1 Connect the SCART to the corresponding connector on  
theTV using the SCART cable supplied (Z).  
Digital Multi-channel sound  
If yourTV is not equipped with a SCART you can select  
one of the following alterative connections:  
Digital multi-channel connection provides the best sound  
quality. For this you need a multi-channel A/V receiver that  
supports one or more of the audio formats supported by  
your DVD player (MPEG 2, Dolby Digital™ and DTS).  
Check the receiver manual and the logos on the front of  
the receiver.  
Video CVBS connection  
1 Connect the (CVBS) VIDEO OUT jack on the DVD player  
to the video in jack on theTV using an optional video cable  
(X).  
AMPLIFIER  
2 Connect the Left and Right AUDIO OUT jacks of the DVD  
player to the audio left/right in jacks on theTV (A).  
TV  
TV  
A
F
X
Z
DIGITAL AUDIO OUT  
PCM-MPEG2-Dolby Digital-DTS  
TV OUT  
A
X
Z
R
L
(CVBS)  
COAXIAL  
AUDIO OUT  
VIDEO OUT  
DIGITAL AUDIO OUT  
PCM-MPEG2-Dolby Digital-DTS  
TV OUT  
R
L
(CVBS)  
COAXIAL  
AUDIO OUT  
VIDEO OUT  
8
PREPARATION  
 
Note:  
General Explanation  
– If the audio format of the digital output does not match the  
capabilities of your receiver, the receiver will produce a strong,  
distorted sound or no sound at all.  
About this manual  
– Six Channel Digital Surround Sound via digital connection  
can only be obtained if your receiver is equipped with a Digital  
Multi-channel decoder.  
To see the selected audio format of the current DVD in the  
StatusWindow, press SYSTEM MENU or Audio.  
This manual gives the basic instructions for operating the  
DVD player. Some DVDs require specific operation or  
allow only limited operation during playback which may not  
respond to all operating commands.When this occurs, the  
symbol Ä appears on theTV screen, indicating that the  
operation is not permitted by the player or the disc.  
NTSC/PAL Settings  
Remote control operation  
You can switch the NTSC/PAL setting of the DVD player to  
match the video signal of yourTV.This setting only affects  
the television’s on-screen display that shows the stop and  
setup modes.You may select either NTSC or PAL.To  
change the DVD player setting to PAL or NTSC, follow the  
steps below.  
Unless stated, all operations can be carried out with the  
remote control.Always point the remote control directly at  
the player, making sure there are no obstructions in the  
path of the infrared beam.  
Corresponding keys on the front panel of the player can  
also be used.  
1 Unplug the DVD player from the mains.  
Menu bar operation  
2 Press and hold 9and T, on the front of the DVD player.  
While holding 9and T, plug in the mains.  
A number of operations can be carried out via the menu  
bar on the screen.The menu bar can be accessed by  
pressing the cursor keys on the remote control.  
Pressing SYSTEM MENU while the menu bar is displayed  
will clear the menu bar from the screen.  
The selected item will be highlighted and the appropriate  
cursor keys to operate will be displayed below the icon.  
< or > indicates that more items are available at the left/  
right of the menu bar. Press 1or 2to select these items.  
3 After PAL or NTSC appears on the display panel of the  
DVD player, release 9and T, at the same time.The PAL  
or NTSC that appears on the display panel indicates the  
current setting.  
4 To change the setting, press T, within three seconds.The  
new setting (PAL or NTSC) will appear on the display  
panel.  
NTSC/PAL Conversion (DVD622  
only)  
This player is equipt. with NTSC/PAL conversion feature to  
convert the video output of the disc to match with yourTV  
system.The conversion supported are as per below.  
Disc  
Output format  
Selected mode  
Type  
Format  
NTSC  
PAL  
AUTO  
NTSC  
PAL  
NTSC  
PAL  
NTSC  
DVD  
VCD  
Not  
Supported  
PAL  
PAL  
PAL  
PAL  
NTSC  
NTSC  
NTSC  
PAL  
NTSC  
PAL  
1 In the Preference Menu, select TV System.  
2 Press 3or 4to select PAL, NTSC or AUTO.  
Notes:  
– AUTO can only be selected when using aTV that has both  
the NTSC and PAL systems.  
– This is applicable for CVBS output on cinch and SCART only  
– Slight picture distortions may occur due to this conversion.  
This is normal.Thus, the AUTO format is most suitable for the  
best picture quality.  
9
PREPARATION  
 
TV Shape  
Initial Setup (Virgin Mode)  
If you have a wide screen (16:9)TV, select 16:9.  
If you have a regular (4:3)TV, select 4:3.  
General  
If you have a 4:3TV, you can also select between:  
Letterbox for a ‘wide-screen’ picture with black bars top  
and bottom, or Pan Scan, for a full-height picture with the  
sides trimmed. If a disc supports the format, the picture will  
be shown accordingly.  
In ‘Initial Setup’ you may have to set your preferences for  
some of the player’s features. (not applicable for all models)  
Operation  
After switching on the player for the very first time, the  
‘Initial Setup Screen’ will appear.  
The menu for the first item to be set is displayed and the  
first option is highlighted.  
Country  
Select your country.This is used as input for the ‘Parental  
Control’ feature (see ‘Access Control’).  
Note:  
Use the 43keys to go through the options in the menu.  
The icon of the selected option will be highlighted.  
Use OK to confirm your selection and to go to the next  
menu.  
– All these items may have to be set during ‘Initial Setup’.  
After that, they can always be changed in the Personal  
Preferences Menu.  
Note:  
– Preferences have to be set in the order of which the item  
menus will appear on the screen.  
– The ‘Initial Setup’ screen will only disappear after the  
settings for the last item have been confirmed.  
– If any keys other than 43or OK are pressed, Ä will  
appear on the screen.  
– If the player is switched off while setting personal  
preferences, all preferences have to be set again after  
switching the player on again.  
Menu Bar/Status Window  
As there are multiple menu-bars, the items on the menu-  
bar are arranged according to usage, availability of direct  
access keys. Pressing the SYSTEM MENU keys once will  
toggle through menu-bar-1, menu-bar-2, menu-bar-3 and  
OFF.  
Menu-bar-1  
Personal Preferences  
Subtitle Language  
Audio Language  
Colour  
The following items may have to be set in Initial  
Setup:  
Menu language  
You can choose from different languages.The On Screen  
Menus will be displayed in the language available on the  
player.  
Sound  
Menu-bar-2  
Step  
Audio language  
Slow motion  
Fast motion  
Angle  
You can choose from different languages. If available on the  
disc, the player will play the audio in the selected language.  
If the selected language is not available, speech will revert  
to the first spoken language on the disc.  
Zoom  
Subtitle language  
Menu-bar-3  
You can choose from different subtitle languages. If available  
on the disc, subtitles will be in the language choosen. If the  
selected language is not available, subtitles will revert to the  
first subtitle language on the disc.  
Title  
Chapter  
Time Search  
FavouriteTrack Selection (FTS)  
10  
PREPARATION  
 
Picture  
TV Shape  
Temporary Feedback Field  
Icons  
See ‘Initial Setup’  
Scan  
Black level shift (NTSC only)  
Repeat All  
Select ON for adapting the colour dynamics to obtain  
richer contrasts.  
RepeatTitle  
RepeatTrack  
Repeat Chapter  
Shuffle  
Shuffle Repeat  
Repeat A to end  
Repeat A-B  
Angle  
Video shift  
The factory centres the video on your screen. Use this  
setting to personalize the position of the picture on your  
TV by scrolling it to the left or right.  
Child Lock On  
Child Safe  
Resume  
Action prohibited  
Colour settings (DVD622 only)  
You can select one of five predefined sets of colour settings  
and one set (Personal) which you can define yourself.  
Personal Preferences  
You can set your own personal preferences on the player.  
General operation:  
Press SYSTEM MENU on the remote control.  
Select in the menu bar.  
The Personal Preferences menu appears.  
Use the 1 2 3 4keys to toggle through the menus,  
submenus and submenu options.  
When a menu item is selected, the cursor keys (on the  
remote control) to operate the item are displayed next to  
the item.  
Press OK to confirm and return to the main menu.  
The following items can be adapted:  
Personal colour (DVD622 only)  
Allows you to fine-tune the selected colour settings  
saturation, brightness and contrast.  
TV System  
Allows you to select between PAL, NTSC and AUTO  
mode depending on yourTV.  
11  
PREPARATION  
 
Sound  
Features  
Digital output  
Access Control  
Factory setting:ALL.This means coaxial output is on. If you  
are not connecting equipment with a digital input, change  
the setting to OFF.  
If your equipment doesn't include a digital multi-channel  
decoder, set the digital output to PCM (Pulse Code  
Modulation).  
Access Control contains the following features:  
Child Lock - When Child Lock is set to ON, a 4-digit code  
needs to be entered in order to playback discs.  
Parental control - Allows the conditional presentation of  
DVDs containing Parental Control information (see ‘Access  
Control’).  
StatusWindow  
Displays the current status of the player and is displayed  
with the menu bar. When disc playback is stopped, it is  
displayed with the ‘Temporary Feedback Field’ in the default  
screen. See ‘On-Screen Display’ information;  
Factory setting is ON. Select OFF to suppress display of the  
Status Window.  
Analog output  
Select Stereo, Dolby Surround or 3D sound (TruSurround)  
to match your system’s playback capability.  
Bit Rate Indicator  
When activated, the bit rate for video, audio as well as total  
bit rate is displayed.This is only applicable during playback  
of DVD and SVCD discs.  
Night Mode  
Optimizes the dynamics of the sound for low volume  
playback.  
Karaoke vocal  
Help text  
Put this setting to ON only when a multi-channel karaoke  
DVD is being played.The karaoke channels on the disc will  
then be mixed into a normal stereo sound.  
When set to ON, help text describes the icons selected.  
Select OFF if you no longer require the help text.  
Language  
Low Power Standby  
Select the required Menu,Audio and Subtitle language. See  
‘Initial Setup’.  
Audio language and Subtitle language can also be adapted  
via the Menu bar on the screen.  
If this is set to ON, the player will go in low-power standby  
when the standby button is pressed (front panel or remote  
control).  
PBC (Playback Control)  
The Playback Control can be set to ON or OFF.  
12  
PREPARATION  
 
Operation  
Loading Discs  
General features  
Note:  
1 Press OPEN/CLOSE on the front of the player to open disc  
– Unless stated, all operations described are based on remote  
control operation. A number of operations can also be carried  
out via the menu bar on the screen.  
tray.  
2 Load your chosen disc in the tray, label side up.  
3 Press OPEN/CLOSE again, to close the tray.  
READ appears in the status window and on the player  
display, and playback starts automatically.  
Moving to another title/chapter  
When a disc has more than one title or  
chapter, you can move to another title/  
chapter as follows:  
Press SYSTEM MENU, then select or  
in the menu bar.  
Note:  
– If ‘Child Lock’ is set to ON and the disc inserted is not  
authorised, the 4-digit code must be entered and/or the disc  
must be authorised (see ‘Access Control’).  
Press 3or 4to select a title/chapter.  
Note:  
Playing a DVD-video and Video  
CD disc  
– If the number has more than one digit, press the keys in  
rapid succession.  
Playing a disc  
Slow Motion  
After inserting the disc  
and closing the tray, playback starts  
Select (SLOW MOTION) in the menu bar.  
Use the 4keys to enter the SLOW MOTION menu.  
The player will now go into PAUSE mode.  
Use the cursor keys 12to select the required speed: -1, -  
1/2, -1/4 or -1/8 (backward), or +1/8, +1/4, +1/2 or +1  
(forward).  
Select 1 to play the disc at normal speed again.  
If ;is pressed, the speed will be set to zero (PAUSE).  
To exit slow motion mode, press Band 3.  
automatically and the status window of the player display  
shows the type of disc loaded, as well as disc’s information  
and playing time.  
The disc may invite you to select an item from a menu. If  
the selections are numbered, press the appropriate  
numerical key; if not, use the 3/4, 1/2keys to highlight  
your selection, then press OK.  
The currently playing title and chapter number are  
displayed.  
Playback may stop at the end of theTitle, and then may  
return to the DVD menu.To go on to the next title, press  
B.  
Still Picture and Frame-by-frame playback  
Select (STEP) in the menu bar.  
Use the 4key to enter the picture by  
picture menu.  
The player will now go into PAUSE  
mode.  
Use the cursor keys 12to select the previous or next  
picture frame.  
To exit STEP mode, press Bor 3.  
To stop playback, press 9.  
The default screen will appear, giving information about  
the current status.  
You can resume playback from the point at which you  
stopped playback. Press B; when you see the Resume icon  
.on the screen, press Bagain.  
The RESUME feature applies not only to the disc in the  
player, but also to the last four discs you have played. Simply  
reload the disc and press RESUME on the remote control  
or, press Bwhen you see the Resume icon .on the  
screen, then press Bagain.  
You can also step forward by pressing ;repeatedly on the  
remote control.  
Scan  
Note:  
Scanning plays the first 10 seconds of each  
chapter/index on the disc.  
Press SCAN.  
To continue playback at your chosen track, press SCAN  
again or press B.  
– DVDs may have a region code.Your player will not play  
discs that have a region code different from the region code of  
your player.  
13  
OPERATION  
 
Search  
Time search  
TheTime Search function allows you to start playing at any  
chosen time on the disc.  
Select (TIME SEARCH) in the menu bar.  
Press 4.  
The player will now go into PAUSE mode.  
A time edit box appears on the screen, showing the  
elapsed playing time of the current disc.  
Use the digit keys to enter the required start time. Enter  
hours, minutes and seconds from left to right in the box.  
Each time an item has been entered, the next item will  
be highlighted.  
Select (FAST MOTION) in the menu  
bar.  
Use the 4keys to enter the FAST  
MOTION menu.  
Use the 12keys to select the required speed: -32, -8 or -4  
(backward), or +4, +8, +32 (forward).  
Select 1 to play the disc at normal speed again.  
To exit FAST MOTION mode, press Bor 3.  
To search forward or backward through different speeds,  
you can also hold down Sor T.  
Press OK to confirm the start time.  
The time edit box will disappear and playback starts  
from the selected time position on the disc.  
Repeat  
DVD-Video Discs - Repeat chapter/  
title/disc  
To repeat the currently playing chapter,  
press REPEAT.  
REPEAT CHPT appears on the player display.  
To repeat the title currently playing , press REPEAT a  
second time  
Zoom  
REPEAT TITL appears on the display.  
To repeat the entire disc, press REPEAT a third time  
REPEAT appears on the display.  
To exit Repeat mode, press REPEAT a fourth time.  
The Zoom function allows you to enlarge the video image  
and to pan through the enlarged image.  
Select (ZOOM).  
Press 3/4to activate the ZOOM function and select the  
required zoom factor: 1.33 or 2 or 4.  
The player will go into Pause mode.  
The selected zoom factor appears below the Zoom icon  
in the menu bar and ‘Press OK to pan’ appears below the  
menu bar.  
The picture will change accordingly.  
Press OK to confirm the selection.  
The panning icons appear on the screen.  
Use the 1234keys to pan across the screen.  
When OK is pressed only the zoomed picture will be  
shown on the screen.  
Video CDs - Repeat track/disc  
To repeat the track currently playing , press REPEAT.  
REPEAT TRK appears on the player display.  
To repeat the entire disc, press REPEAT a second time.  
REPEAT appears on display and screen.  
To exit Repeat mode, press REPEAT a third time.  
Repeat A-B  
To repeat a sequence in a title:  
Press REPEAT A-B at your chosen starting  
point;  
A- appears briefly on the screen.  
Press REPEAT A-B again at your chosen end point;  
REPEAT A-B appears briefly on the display, and the repeat  
sequence begins.(REPEAT A-B is displayed on the front panel  
of the player)  
To exit ZOOM mode:  
– Press B to resume playback.  
To exit the sequence, press REPEAT A-B.  
Shuffle  
DVD-Video discs  
This shuffles the playing order of chapters  
within a title, if the title has more than one  
chapter.  
Press SHUFFLE during playback.  
SHUFFLE appears on the screen for about 2 seconds.  
To return to normal playback, press SHUFFLE again.  
Video CDs  
Press SHUFFLE during playback.  
SHUFFLE appears on the screen for about 2 seconds.  
To return to normal playback, press SHUFFLE again.  
14  
OPERATION  
 
FTS-Video  
Special DVD features  
The FTS-Video function allows you to store your favourite  
titles and chapters (DVD) and favourite tracks and indexes  
(VCD) for a particular disc in the player memory.  
Checking the contents of DVD-Video discs:  
Menus  
FTS programme can contain 20 items (titles, chapters).  
An programmed FTS will be placed on top of the list when  
playback is activated.When the list is full, a new programme  
will replace the last programme on the list.  
DVDs may contain menus to navigate the disc and access  
special features.To use the menu, press the appropriate  
numerical key; or use the 4, 3, 2, 1keys to highlight your  
selection, then press OK..  
The programme can be selected and played at any time.  
Title/Disc menu  
Storing a FTS-Video Programme  
In STOP mode, select VIDEO FTS c in the menu bar.  
Press 4to open the menu.  
The VIDEO FTS menu appears.  
Press DISC MENU.  
If the current title has a menu, the menu will appear on  
the screen otherwise, the disc menu will be displayed.  
The menu can list camera angles, spoken language and  
subtitle options, and chapters for the title.  
Press 2or 1or FTS to select ON or OFF.  
Storing titles/tracks  
To remove the title menu, press DISC MENU again.  
Press 4to select TITLES.  
Use 2and 1to select the required title.  
Press OK if you wish to store the entire title.  
The title number will be added to the list of selections.  
Camera Angle  
If the disc contains sequences recorded from different  
camera angles, the angle icon appears, showing the number  
of available angles and the angle being shown currently.You  
can then change the camera angle if you wish.  
Use the 3/4keys to select the required angle icon.  
After a while, playback changes to the selected angle.The  
angle icon remains displayed until multiple angles are no  
longer available.  
Storing chapters/indexes  
Press 4on the selected title number.  
The title number will be marked and the highlight moves  
to the first available chapter number for this title.  
Use 2and 1to select the required chapter number.  
Press OK to confirm the selection.  
The title/chapter selection will be added to the list of  
selections.  
Changing the audio language  
Select Y (AUDIO) in the menu bar.  
Press Y or 3/4repeatedly to see the different languages.  
Press SYSTEM MENU to exit the VIDEO FTS c menu.  
Erasing a FTS-Video Programme  
In STOP mode, select VIDEO FTS c in the menu bar.  
Use 4to select PROGRAM.  
Use 2and 1to select the required selection number.  
Press OK to erase the selection.  
Subtitles  
Select Z (SUBTITLE) in the menu bar.  
Press Z or 3/4repeatedly to see the different subtitles.  
Press SYSTEM MENU to exit.  
If you wish to erase all selections:  
In STOP mode, select VIDEO FTS c in the menu bar.  
Use 4to select CLEAR ALL.  
Press OK.  
All selections will now be erased.  
Press SYSTEM MENU to exit.  
15  
OPERATION  
 
Moving to another track  
Special VCD & SVCD features  
Press Sor Tbriefly during playback to go to the  
next or to return to the beginning of the current track.  
Press Stwice briefly to step back to the previous track.  
To go directly to any track, enter the track number using  
the numerical keys (0-9).  
Playback Control (PBC)  
Load aVideo CD with PBC and press B.  
Go through the menu with the keys indicated on theTV  
screen until your chosen passage starts to playback. If a  
PBC menu consists of a list of titles, you can select a title  
directly.  
Shuffle  
Enter your choice with the numerical keys (0-9).  
Press RETURN to go back to the previous menu.  
You may also set to PBC OFF under Personal  
Preferences.  
Press SHUFFLE during playback.  
The order of the tracks is changed.  
To return to normal playback, press  
SHUFFLE again.  
Repeat track/disc  
Playing an audio CD  
To repeat the track currently playing ,  
press REPEAT.  
REPEAT TRK appears on the display.  
To repeat the entire disc, press REPEAT a second time.  
REPEAT appears on the display.  
After loading the disc, playback starts automatically.  
If theTV is on, the Audio CD screen appears.  
The number of tracks and the total playing time will be  
shown on the screen.  
During playback, the current track number and its elapsed  
playing time will be shown on the screen and on the player  
display.  
To exit Repeat mode, press REPEAT a third time.  
Repeat A-B  
Playback will stop at the end of the disc.  
To stop playback at any other time, press 9.  
To repeat a sequence:  
Press REPEAT A-B at your chosen starting  
point;  
A- appears on the player display.  
Press REPEAT A-B again at your chosen end point;  
A-B appears on the display, and the sequence begins to  
playback repeatedly.  
To exit the sequence, press REPEAT A-B again.  
Scan  
Scanning plays the first 10 seconds of each  
track on the disc.  
Press SCAN.  
Pause  
To continue playback at your chosen track, press SCAN  
again or press B.  
Press ;during playback.  
To return to playback, press B.  
Search  
FTS Programme  
To search forward or backward through  
the disc at four times normal speed, hold  
down Sor Tfor about one second  
during playback.  
FTS Programme allows you to store your favourite tracks  
for a particular disc in the player memory.  
Each FTS Programme can contain 20 tracks.  
Search begins, and sound is partially muted.  
To step up to eight times the normal speed, press Sor  
Tagain.  
Search goes to eight times the speed, and the sound is  
muted.  
To return to four times the normal speed, press Sor  
Tagain.  
If theTV is on, search speed and direction are indicated on  
the screen each time Sor Tis pressed.  
To end the search, press Bto resume playback or 9to  
stop.  
16  
OPERATION  
 
Downloading MP3 files from the Internet or ripping songs  
from your own legal discs, is a delicate process.  
Storing an FTS Programme  
1 Load a disc and stop playback.  
2 Use 4to go to the list of available tracks.  
Approximate total  
MP3-CD time  
Approximate  
Reduction Ratio  
Sound  
Quality  
Comment  
Bit Rate  
Sound quality significantly affected  
not recommended.  
AM radio  
32 kbps  
64 kbps  
40 : 1  
20 : 1  
15 : 1  
10 : 1  
5 : 1  
40 hrs  
20 hrs  
15 hrs  
10 hrs  
5 hrs  
3 Use 2or 1to select tracks from the list.  
To go directly to any track, enter the track number using  
the numerical keys (0-9).  
4 Store each track by pressing OK.  
The track numbers will be added to the list.  
The number of tracks and the playing time of the  
programme will be shown on the screen and the player  
display.  
FM radio  
Near-CD  
CD-like  
CD*  
Balanced sound quality  
compression rate  
96 kbps  
128 kbps  
256 kbps  
320 kbps  
Compression rate low  
suggest to play CDs instead  
CD*  
3 : 1  
3 hrs  
You may experience an occasional skipwhile  
listening to your MP3 files.This is normal.  
Additional note for MP3 disc Playback:  
– In compliance with the SDMI, digital-out is muted  
while playing MP3 discs.  
– Due to the recording nature of Digital Audio MP3  
(DAM),only Digital Audio music will play.  
– The disc reading time may exceed 10 seconds due  
to the large number of songs compiled into one  
disc.  
When your FTS Programme is complete, press Bto start  
playback, or 3to go back to Stop mode. In either case, the  
FTS Programme will be automatically memorized.  
Switching FTS ON/OFF  
1 Use 34to move to select desired tracks.  
2 Use 2or 1to select either ON or OFF.  
– Only the first session of multisession discs is  
supported.  
Erasing a track from an FTS Programme  
Album/Title  
1 Use 4to go to the list of selected tracks.  
This feature allows you to view and select the next or  
previous MP3 disc Album/Title.  
2 Use 2and 1to select the track number you wish to erase.  
3 Press OK.  
The track number will be erased from the list of selected  
1 Press 3/4to scroll through the previous or next Album.  
2 Press 1/2to scroll through the previous or nextTrack.  
tracks.  
Album  
Track  
Time  
Erasing the complete programme  
1 Use 4to select CLEAR ALL, then press OK.  
The complete FTS Programme for the disc will be  
erased.  
will be displayed.  
3 You can also select the desired album/track number directly  
from the numerical key pad on the remote control.  
MP3 Disc Features (DVD622 only)  
Support following MP3-CD formats (ISO9660  
format):  
Note:  
In STOP mode: numbers are used for ALBUM selection.  
In PLAY mode:numbers are used for TRACK selection.  
Max. 30 characters  
Only the following modes are possible for MP3 discs;  
– STOP / PLAY / PAUSE  
– SKIP NEXT / PREVIOUS  
Max. nested directory is 8 levels  
The max.ALB number is 32  
SupportedVBR bit-rate  
Supported sampling frequencies for MP3 disc are: 32 kHz,  
44.1 kHz, 48 kHz  
– REPEAT (ALBUM /TRACK / DISC)  
MP3 Discs - Album/Track/Disc  
Supported Bit-rates of MP3 disc are: 32, 64, 96, 128, 192,  
256 (kbps)  
To repeat track, press REPEAT.  
REPEAT TRK appears on the display.  
To repeat album, press REPEAT a second time.  
REPEAT ALBM appears on the player display.  
To repeat disc, press REPEAT a third time.  
REPEAT DISC appears on the player display.  
Following formats cant be supported  
The files like *.WMA, *AAC, *.DLF, *.M3U, *.PLS  
Chinese filename  
The non-session closed discs  
The discs recorded under UDF format  
17  
OPERATION  
 
Access Control  
Access Control; Child Lock  
(DVD-Video and Video CD)  
Activating/deactivating the child lock  
1 When disc playback is stopped, select ACCESS  
CONTROL in the features menu using the 3/4keys.  
2 Enter a 4-digit code of your own choice.  
3 Enter the code a second time.  
4 Move to “CHILD LOCK” using the 3/4keys.  
5 Move to LOCK/UNLOCK using the 2key.  
6 Select LOCK using the 3/4keys.  
7 Press OK or 1to confirm, then press 1again to exit the  
Deauthorizing discs  
menu.  
Now unauthorized discs will not be played unless the  
4-digit code is entered.  
8 Select UNLOCK to deactivate the CHILD LOCK.  
Insert the disc. See ‘Loading disc’.  
Playback starts automatically.  
Press 9while { is visible.  
The | will appear and the disc is now deauthorized.  
Note: Confirmation of the 4-digit code is necessary when:  
– The code is entered for the very first time (see above),  
– The code is changed (see ‘Changing the 4-digit code’),  
– The code is cancelled (see ‘Changing the 4-digit code’).  
Access control; Parental  
Control (DVD-Video only)  
Movies on DVDs may contain scenes not suitable for  
children.Therefore, disc may contain ‘Parental Control’  
information which applies to the complete disc or to  
certain scenes on the disc.These scenes are rated from 1  
to 8, and alternative, more suitable scenes are available on  
the disc. Ratings are country dependent.The ‘Parental  
Control’ feature allows you to prevent discs from being  
played by your children or to have certain discs played with  
alternative scenes.  
Authorizing discs  
Insert the disc. See ‘Loading disc’.  
The ‘child protect’ dialog will appear.  
You will be asked to enter your secret code for ‘Playback  
Once ‘or ‘Playback Always.’ If you select ‘Playback Once’, the  
disc can be played as long as it is in the player and the  
player is ON. If you select ‘Playback Always’, the disc will  
become child safe (authorized) and can always be played,  
even if the Child Lock is set to ON.  
Notes:  
– The player memory maintains a list of 120 authorized  
(‘Child safe’) disc titles.A disc will be placed in the list when  
‘Playback Alwaysis selected in thechild protect’ dialog.  
– Each time a ‘child safe’ disc is played, it will be placed on  
top of the list.When the list is full and a new disc is added, the  
last disc in the list will be removed from the list.  
– Double sided DVDs may have a different ID for each side.  
In order to make the disc ‘child safe’, each side has to be  
authorized.  
– Multi-volumeVCDs may have a different ID for each  
volume. In order to make the complete set ‘child safe’, each  
volume has to be authorized.  
18  
ACCESS CONTROL  
 
Activating/Deactivating Parental Control  
Changing the 4-digit code  
1 When disc playback is stopped, select ACCESS  
CONTROL in the features menu using the 3/4keys.  
2 Enter your 4-digit code. If necessary, enter the code a  
second time.  
3 Move to Parental Control using the 3/4keys.  
4 Move to VALUE ADJUSTMENT (1-8) using the 2key.  
5 Then use the 3/4keys or the numerical keys on the  
remote control to select a rating from 1 to 8 for the disc  
inserted.  
1 When disc playback is stopped, select ACCESS  
CONTROL in the features menu using the 3/4keys.  
2 Enter the old code.  
3 Move to CHANGE CODE using the 4key.  
4 Press the 2key.  
5 Enter the new 4-digit code.  
6 Enter the code a second time and reconfirm by pressing  
OK.  
7 Press 1to exit the menu.  
Rating 0 (displayed as ‘– –’):  
Parental Control is not activated.The Disc will be played in  
full.  
If you forget your 4 digit code  
1 Press 9to exit ‘Child Protect’ screen.  
Ratings 1 to 8:  
2 Select ACCESS CONTROL in the features menu using  
The disc contains scenes not suitable for children. If you set  
a rating for the player, all scenes with the same rating or  
lower will be played. Higher rated scenes will not be played  
unless an alternative is available on the disc.The alternative  
must have the same rating or a lower one. If no suitable  
alternative is found, playback will stop and the 4-digit code  
has to be entered.  
the 3/4keys.  
3 The 4-digit code can be cancelled by pressing 9four times  
in the ‘Access Control’ dialog.  
4 You can then enter a new code (twice!) as described above  
(Changing the 4 digit code).  
Parental Control Disclaimer  
6 Press OK or 1to confirm, then press 1again to exit the  
menu.  
This DVD player features the PARENTAL CONTROL  
system which is intended to activate when playing DVD  
discs furnished with certain software coding.This is  
according to technical standards adopted by the set maker  
and disc content industries.  
Please note that the PARENTAL CONTROL system  
will not operate a DVD disc which is not furnished with the  
appropriate software coding.Also note that at the time of  
release of this DVD player, certain aspects of the technical  
standards had not been settled between set makers and  
the disc industries.  
Country  
On this basis Philips cannot guarantee the functioning of  
PARENTAL CONTROL system and denies any liability  
associated with unintended watching of disc content.  
If in doubt, please make sure the disc plays according to  
your PARENTAL CONTROL settings before you allow  
children access to the player.  
1 When disc playback is stopped, select ACCESS  
CONTROL in the features menu using the 3/4keys.  
2 Enter the 4-digit code.  
3 Move to CHANGE COUNTRY using the 4key.  
4 Press the 2key.  
5 Select a country using 3/4.  
6 Press OK or 1to confirm, then press 1again to exit the  
menu.  
19  
ACCESS CONTROL  
 
Before Requesting Service  
If it appears that the DVD-Video player is faulty, first consult this checklist. It may be that something has been overlooked. Under  
no circumstances attempt to repair the system yourself; this will invalidate the warranty.  
Look for the specific symptom(s).Then perform only the actions listed to remedy the specific symptom(s).  
Symptom  
Remedy  
No power  
– Make sure the mains cord (AC Power) is properly connected.  
– Check if there is power at the AC outlet by plugging in another appliance.  
No picture  
– Check if theTV is switched on.  
– Check the video connection.  
Distorted picture  
– Check the disc for fingerprints and clean the disc with a soft cloth, wiping  
from the centre to the edge in a straight line.  
– Sometimes a small amount of picture distortion may appear .This is not a  
malfunction.  
Completely distorted picture  
or no colour with player menu.  
– If the picture is distorted completely or if the picture rolls vertically,  
make sure the NTSC/PAL setting at the DVD player matches the video  
signal of your television.  
– If yourTV video signal is NTSC, select the NTSC setting at the DVD player.  
– If your video signal is PAL, select the PAL setting - see NTSC/PAL SETTINGS.  
Distorted or Black/White picture  
with DVD orVideo CD.  
– The disc format does not match yourTV’s video signal (PAL/NTSC) - see  
NTSC/PAL Conversion.  
No sound  
– Check audio connections.  
– If you are using a HiFi amplifier, try another sound source.  
Distorted sound from HiFi  
amplifier.  
– Check to make sure that no audio connections are made to the amplifier  
phono input.  
No audio at digital output.  
– Check the digital connections.  
– Check the settings menu to make sure the digital output is set to ALL or  
PCM.  
– Check if the audio format of the selected audio language matches your  
receiver capabilities.  
– Not applicable for MP3  
Disc cant be played.  
– Ensure the disc label is facing up.  
– Clean the disc.  
– Check if the disc is defective by trying another disc.  
– Check to see if the disc is defective, badly scratched or warped (not flat)  
No return to start-up screen when  
disc is removed.  
– Reset by switching the player off, then on again.  
– Check to see if the programme requires another disc to be loaded.  
The player does not respond to  
the remote control.  
– Aim the remote control directly at the sensor on the front of the player.  
– Remove any obstacles between the player and the remote control.  
– Inspect or replace the batteries in the remote control.  
Buttons do not work.  
– In order to completely reset the player, unplug the AC cord from the AC  
outlet. (Please ensure that the set is not in Initial Setup mode)  
Player does not respond to some  
operating commands during  
playback.  
– Operations may not be permitted by the disc. Refer to the instructions of  
the disc.  
DVD-Video player cannot read  
CDs/DVDs  
– Use a commonly available cleaning CD/DVD to clean the lens before  
sending the DVD-Video player for repair.  
20  
BEFORE REQUESTING SERVICE  
 
Specification  
PLAYBACK SYSTEM  
DVD-Video  
CONNECTIONS  
SCART  
Euroconnector  
Video CD & SVCD  
CD (CD-R and CD-RW)  
DVD+RW  
Video Output  
Audio L+R output  
Digital Output  
Cinch (yellow)  
Cinch (white/red)  
1 coaxial  
MP3 (DVD622 only)  
IEC958 for CDDA / LPCM  
IEC1937 for MPEG1/2, Dolby Digital and DTS  
OPTICAL READOUT SYSTEM  
Lasertype  
Semiconductor AlGaAs  
CABINET  
Numerical Aperture  
0.60 (DVD)  
Dimensions (w x h x d)  
Weight  
435 x 81 x 295 mm  
Approx. 3.5 Kg  
0.45 (VCD/CD)  
650 nm (DVD)  
780 nm (VCD/CD)  
Wavelength  
GENERAL FUNCTIONALITY  
Stop / Play / Pause  
DVD DISC FORMAT  
Medium  
Diameter  
Playing time  
(12cm)  
Fast Forward / Backward  
Time Search  
Step Forward / Backward  
Slow Motion  
Title / Chapter /Track Select  
Skip Next / Previous  
Optical Disc  
12cm (8cm)  
One layer  
Dual layer  
Two side  
2.15 h*  
4 h*  
4.30 h*  
Single layer  
Two side  
Repeat (Chapter /Title / All) or (Track / All)  
A-B Repeat  
8 h*  
Dual layer  
Shuffle  
Scan  
VIDEO FORMAT  
DA Converter  
Signal handling  
New enhanced user graphical interface  
Perfect Still with digital multi-tap filter  
Zoom (xl.33, x2. x4) with picture enhancement  
Smart Picture for convenient personal colour setting (DVD622 only)  
PAL/NTSC Conversion (DVD622 only)  
Screen Saver (Dim 75% after 15 min.)  
3D Sound (TruSurround)  
10 bits  
Components  
MPEG2 for DVD,  
MPEG1 forVCD  
Digital Compression  
TV STANDARD  
Number of lines  
Playback  
(PAL/50Hz)  
625  
Multistandard  
(NTSC/60Hz)  
525  
(PAL/NTSC)  
Virtual Jog Shuttle  
Audio and video bit rate indicator  
DVD  
DVD FUNCTIONALITY  
Horiz. Resolution  
Vertical Resolution  
720 pixels  
576 lines  
720 pixels  
480 lines  
Multi-angle Selection  
Audio Selection (1 out of max. 8 languages)  
Subtitles Selection (1 out of max. 32 languages)  
Aspect Ratio conversion (16:9, 4:3 Letterbox, 4:3 Pan Scan)  
Parental Control and Disk Lock  
Disc Menu support (Title Menu and Root Menu)  
Resume (5 discs) after stop / standby  
VCD  
Horiz. Resolution  
Vertical Resolution  
352 pixels  
288 lines  
352 pixels  
240 lines  
VIDEO PERFORMANCE  
Video output  
RGB (SCART) output  
Black Level Shift  
ProgrammingTitles/chapters with Favourite Selection  
1Vpp into 75 ohm  
0.7Vpp into 75 ohm  
On/Off  
VIDEO CD FUNCTIONALITY  
Playback Control forVCD 2.0 discs  
Disc Lock  
Video Shift  
Left/Right  
Resume (5 discs) after stop / standby  
ProgrammingTracks with Favourite Selection  
AUDIO FORMAT  
Digital  
MPEG  
DTS/Dolby Digital  
PCM  
Compressed Digital  
16, 20, 24 bits  
fs, 44.1, 48, 96 kHz  
AUDIO CD FUNCTIONALITY  
Time Display (Total /Track / RemainingTrackTime)  
Full audio functionality with remote control  
Programming with FavouriteTrack Selection  
Analog Sound Stereo  
Dolby Pro Logic downmix from Dolby Digital multi-channel sound  
3D Sound (TruSurround) for virtual 5.1 channel sound on 2 speakers  
MP3 FUNCTIONALITY (DVD622 only)  
Time Display (Track)  
AUDIO PERFORMANCE  
DA Converter  
DVD  
24 bits  
Album andTrack Selection  
Repeat (Disc / Album /Track)  
fs 96 kHz  
fs 48 kHz  
fs 44.1 kHz  
fs 44.1 kHz  
4 Hz - 44 kHz  
4 Hz - 22 kHz  
4 Hz - 20 kHz  
4 Hz - 20 kHz  
100 dB  
97 dB  
110 dB  
88 dB  
MPEG Audio L3  
Video CD  
CD  
*
typical playing time for movie with 2 spoken languages and 3 subtitle languages.  
Signal-Noise (1kHz)  
Dynamic Range (1kHz)  
Crosstalk (1kHz)  
Distortion and Noise (1kHz)  
MPEG MP3  
Specifications subject to change without prior notice  
21  
SPECIFICATION  
 

Peg Perego Riding Toy ES 3030 User Manual
Pelco Marine Instruments C521M User Manual
Pentax Camera Flash 60 R User Manual
Philips Speaker System DGX220 User Manual
Polaris Offroad Vehicle RZR 4 800 User Manual
Poulan Lawn Mower PZ4822 User Manual
Powermate Portable Generator PM0606750 User Manual
Powerware Power Supply 8 10 kVA User Manual
Premier Mounts TV Mount RTM C User Manual
ProScan Flat Panel Television PLCD2401A User Manual