Philips Bluetooth Headset SHB6000 00 User Manual

Register your product and get support at  
Bluetooth stereo headset  
SHB6000/00  
SHB6000/28  
EN  
User manual  
 
The integrated battery shall not be exposed to excessive heat  
such as sunshine, fire or the like.  
Ensure that there is no foreign objects inside the USB cover  
and close the cover tightly.  
1 Important  
Hearing Safety  
Disposal of your old product  
Your product is designed and manufactured with high quality  
materials and components, which can be recycled and reused.  
Danger  
To avoid hearing damage, limit the time you use the headphones at high volume  
and set the volume to a safe level.The louder the volume, the shorter is the safe  
listening time.  
When this crossed-out wheeled bin symbol is attached to a product  
it means that the product is covered by the European Directive  
2002/96/EC.  
Please inform yourself about the local separate collection system for  
electrical and electronic products.  
Please act according to your local rules and do not dispose of your  
old products with your normal household waste. Correct disposal of  
your old product helps to prevent potential negative consequences  
for the environment and human health.  
Be sure to observe the following guidelines when using your  
headphones.  
Listen at reasonable volumes for reasonable periods of time.  
Be careful not to adjust the volume continuously upwards as  
your hearing adapts.  
Do not turn up the volume so high that you can’t hear what’s  
around you.  
You should use caution or temporarily discontinue use in  
potentially hazardous situations.  
Excessive sound pressure from earphones and headphones  
can cause hearing loss.  
Using this headset with both ears covered while driving is not  
recommended and may be illegal in some areas while driving.  
For your safety, avoid distractions from music or phone calls  
while in traffic or other potentially dangerous environments.  
Battery disposal  
Your product contains batteries covered by the European Directive  
2006/66/EC, which cannot be disposed of with normal household  
waste.  
Electric-, Magnetic- and Electromagnetic  
Fields (EMF)  
Please inform yourself about the local rules on separate collection  
of batteries. The correct disposal of batteries helps prevent  
potentially negative consequences on the environment and human  
health.  
1. Royal Philips Electronics manufactures and sells many products  
targeted at consumers, which, like any electronic apparatus, in  
general have the ability to emit and receive electromagnetic signals.  
2. One of Philips’ leading Business Principles is to take all necessary  
health and safety measures for our products, to comply with all  
applicable legal requirements and to stay well within the EMF  
standards applicable at the time of producing products.  
3. Philips is committed to develop, produce and market products that  
cause no adverse health effects.  
4. Philips confirms that if its products are handled properly for their  
intended use, they are safe to use according to scientific evidence  
available today.  
5. Philips plays an active role in the development of international  
EMF and safety standards, enabling Philips to anticipate further  
developments in standardization for early integration in its products.  
Remove the integrated battery  
Warning  
Make sure the headset is disconnected from the USB charging cable  
before removing the battery.  
If there is no collection/recycling system for electronic products in  
your country, you can protect the environment by removing and  
recycling the battery before disposing the headset.  
General information  
To avoid damage or malfunction:  
Do not expose the headset to excessive heat.  
Do not drop your headset.  
The headset can be washable under running tape water  
while the charging socket shall not be exposed to dripping or  
splashing.  
Do not allow your headset to be submerged in water.  
Do not use any cleaning agents containing alcohol, ammonia,  
benzene, or abrasives.  
About operating and storage temperatures  
Do not operate or store in a place where temperature is  
below -15ºC (5ºF) or above 55ºC (131ºF) as this may shorten  
your battery life.  
2
EN  
 
 
Notice for the European Union  
Notice for Canada  
Operation is subject to the following two conditions:  
a This device may not cause interference3 and  
Hereby, Philips Consumer Lifestyle, BG Accessories, declares that this  
Philips Bluetooth headset SHB6000 is in compliance with the essential  
requirements and other relevant provisions of Directive 1999/5/EC.  
This product has been designed, tested and manufactured according  
to the European R&TTE Directive 1999/5/EC.  
b This device must accept any interference, including  
interference that may cause undesired operation of the  
device. The term “IC:” before the certification / registration  
number only signifies that registration was performed based  
on a Declaration of Conformity indicating that Industry  
Canada technical specifications were met. It does not imply  
that Industry Canada approved the equipment.  
Notice for USA (FCC)  
Trademarks  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) this device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
This equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation.This equipment  
generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may  
cause harmful interference to radio communications.  
Trademarks are the property of Koninklijke Philips Electronics N.V.  
or their respective owners.The Bluetooth word mark and logos  
are owned by the Bluetooth SIG, Inc. and any use of such marks by  
Koninklijke Philips Electronics N.V. is under license.  
However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the  
following measures:  
Relocate the receiving antenna.  
Increase the separation between equipment and receiver.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
Warning  
Changes or modifications made to this equipment not expressly  
approved by Philips may void the FCC authorization to operate this  
equipment.  
Note  
FCC/IC Radiation Exposure Statement: This equipment complies  
with FCC/IC radiation exposure limits set forth for an uncontrolled  
environment. End users must follow the specific operating instructions  
for satisfying RF exposure compliance.  
This transmitter must not be co-located or operating in conjunction  
with any other antenna or transmitter.  
Philips Consumer Lifestyle  
A division of Philips Electronics North America Corporation  
P.O.Box 10313  
Stamford, CT 06904  
Phone: 1-888-PHILIPS (744-5477)  
EN  
3
 
 
2 Your bluetooth stereo  
headset  
Congratulations on your purchase, and welcome to Philips!To fully  
benefit from the support that Philips offers, register your product at  
Introduction  
With the Philips Bluetooth stereo headset SHB6000, you can enjoy  
convenient wireless hands-free call. Ergonomically designed soft ear  
bud provides all-day wearing comfort.You can simply recharge your  
headset on your computer or with a USB charger.  
Pouch  
Compatibility  
Spend a few minutes to learn more about your headset to enjoy your  
Philips Bluetooth stereo headset to its fullest.  
Your headset is compatible with Bluetooth enabled mobile phones.  
It features Bluetooth version 2.1+EDR. It also works with devices  
featuring other Bluetooth versions that support the Headset profile  
(HSP), A2DP-Advanced Audio Distribution Profile, Hands-free  
profile (HFP) and Audio/Video remote control profile (AVRCP).  
What’s in the box  
Check and identify the contents of your package:  
Bluetooth headset  
USB charging cable  
Exchangeable rubber ear caps  
Quick Start Guide  
EN  
Philips Bluetooth stereo headset SHB6000  
Power on/off  
LED  
Adjustable ear hook  
Mic  
Exchangeable ear caps  
Charging socket  
Quick start guide  
4
EN  
 
 
Overview of your Bluetooth stereo  
headset  
Power on/off  
LED  
Adjustable ear hook  
Mic  
Exchangeable ear caps  
Charging socket  
EN  
5
 
 
Pair the headset with your mobile phone  
3 Get started  
Before you use the headset with a mobile phone for the first time,  
pair it with the mobile phone.A successful pairing establishes a  
unique encrypted link between the headset and the mobile phone.  
The headset stores the last eight links in the memory. If you try to  
pair more than eight devices, the link for the earliest paired device is  
overwritten.  
Charge the headset  
Warning  
Before you use your headset for the first time, charge the battery for  
four hours for optimum battery capacity and lifetime.  
1 Ensure that the mobile phone is turned on and its Bluetooth  
feature is activated.  
Use only the original USB charging cable to avoid any damage.  
Finish your call before charging the headset, as connecting the headset  
for charging will power off the unit.  
2 Ensure that the headset is charged and turned off.  
You can operate the headset normally during charge.  
3 Press until the LED starts flashing red and blue alternately.  
Do not stop pressing the button after seeing the blue LED  
only.  
1 Remove the USB cap.  
» The headset is in pairing mode, which lasts five minutes.  
4 Pair the headset with the mobile phone. For details, refer to  
the user manual of the mobile phone.  
A sample pairing is shown below.  
1 Under Bluetooth menu on the mobile phone, search for the  
headset.  
2 On mobile phones using Bluetooth 2.1+EDR or higher, you do  
not need to enter a pass code.  
3 From the found devices, select Philips SHB6000.  
Enter “0000” (4 zeros), if prompted to enter the pin code  
of the headset.  
10:35  
10:36  
10:37  
Settings  
Connectivity  
Settings  
Settings  
Connectivity  
Bluetooth  
Devices Found  
2 Plug the headset into a powered USB port with USB charging  
Enter Password  
****  
Add  
Bluetooth  
device  
Philips SHB6000  
cable.  
» LED turns red during charge and turns off when the headset  
is fully charged.  
0000  
Select  
Select  
Select  
Back  
Back  
Back  
Tip  
Typically, a full charge takes two hours.  
6
EN  
 
 
Operate the headset  
4 Use the headset  
Enter pairing mode  
Ensure the headset is off. Press until  
LED starts blinking red/blue alternately.  
Connect the headset to your mobile phone  
Check battery  
When first use: Hold for 2 seconds.  
During operation: Hold VOL + and VOL  
- simultaneously.  
1 With the mobile phone turned on, press until the LED lights  
>50%: 1 blue flash  
up, to turn on the headset.  
>25%: 2 red flash  
<25%: 3 red flash  
Hold until LED turns on/off.  
Tap  
» Once turned on, the headset reconnects automatically to  
the last device it was connected to.  
Turn headset on/off  
Play/Pause music  
Stop music  
Next / Previous track  
Adjust volume  
» If the last connected device is not available, the headset  
tries to reconnect to the second to last device that was  
connected to the headset. If it cannot find this device, it  
will look for all previously paired devices in the order of  
last usage, until it finds a device to connect to.The headset  
stores up to eight previously paired devices.  
Hold  
Tap  
/
Press VOL +/VOL -  
Tap  
Hold  
Pick up / End a call  
Reject a call  
Redial the last number Press twice quickly.  
Activate voice dialing* Hold until beep occurs.  
Mute/Unmute the Mic Double tap during a call.  
Tip  
If you turn on the mobile phone or its Bluetooth feature after turning  
on the headset, connect the headset from the Bluetooth menu of  
your mobile phone.  
Transfer a call to a  
mobile phone  
Hold during a call.  
* Available if supported by your mobile phone.  
Automatic power saving  
Manage 3-way calls  
If the headset cannot find any Bluetooth device to connect to in  
range within five minutes, it automatically powers down to save  
battery life.  
If your mobile phone and network operator support 3-way-calls, you  
can manage 3-way-calls via the headset.  
To hold the active call and  
accept a waiting call  
To drop the active call and  
accept a waiting call  
Press while the 2nd call is  
coming in.  
Hold while the 2nd call is  
coming in.  
Get the best fit  
1 Choose the earbuds that best fit for your ear canal.  
To swap a call  
Press during a call.  
2 Gently blend the ear hook to fit into your ears.  
3 Adjust the rubber part of the ear hook to the height that you  
feel fit.  
4 Twist the earbuds to the right position for best fit and noise  
LED and sound indication  
isolation.  
The red/blue LED flashes alternately. The headset is ready for  
pairing.  
The blue LED flashes once every 6  
seconds.  
The headset is connected  
to the device.  
The blue LED flashes twice every 3 The headset is not  
seconds. connected.  
The blue LED flashes once every half There is an incoming/  
a second.  
outgoing call.  
The blue LED flashes once every  
second.  
The headset is active on  
a call.  
The red LED flashes three times and The battery is low in  
beeps twice every minute.  
Solid red LED.  
power.  
The headset is charging.  
The LED is off.  
The headset is off./Charging  
is finished.  
The headset beeps every 5 seconds. The Mic is muted.  
Clean the headset  
A few ways to clean the headset:  
Wipe with clean cloth.  
Wash it under running tape water.  
Caution  
Do not dive with this product or immerse it into water.  
EN  
7
 
 
5 Technical data  
Up to 4.5 hours of playtime or 5 hours of talk time  
Up to 120 hours of standby time  
Typical time for a full charge: 2 hours  
Rechargeable Lithium-Polymer battery (105 mAh)  
Bluetooth 2.1+EDR, Bluetooth stereo support (A2DP-  
Advanced Audio Distribution Profile, AVRCP-Audio/Video  
Remote Control Proflie), Bluetooth mono support (HSP-  
Headset Profile, HFP-Hands-Free Profile)  
Acoustic echo cancelation  
Dual mic noise suppression  
Adjustable ear hook  
Noise isolating in-ear design  
Operating range up to 10 meters (33 feet)  
3 sizes of ear caps included  
Quick-dry pouch included  
Sweat proof and fully washable  
Specifications are subject to change without notice.  
8
EN  
 
 
6 Frequently asked  
questions  
Bluetooth headset does not switch on.  
Battery is low.  
» Charge the headset.  
No connection to a mobile phone.  
Bluetooth disabled.  
» Enable the Bluetooth feature on your mobile phone and  
turn on the mobile phone before you turn on the headset.  
Pairing does not work.  
The headset is not in pairing mode.  
» Follow the steps described in this user manual.  
» Ensure that you see the LED light flashes red and blue  
alternately before you release the button. Do not stop  
pressing the button after seeing the blue LED only.  
The mobile phone cannot find the headset.  
The headset may be connected to another previously paired  
device.  
» Turn the currently connected device off or move it out of  
range.  
Pairings may have been reset or headset has been previously  
paired with other device.  
» Pair the headset with the mobile phone again as described in  
the user manual.  
Voice dialing or redialing does not work.  
Your mobile phone may not support this feature.  
The other side cannot hear me, and I hear a beep noise every  
couple of seconds.  
The microphone is muted.  
» Quickly press twice to enable the microphone.  
Audio quality is poor and crackling noises can be heard.  
Bluetooth audio source is out of range.  
» Reduce the distance between the headset and the Bluetooth  
audio source, or remove obstacles between them.  
The earbud is not positioned correctly.  
» Ensure that you position the earbud as described in this user  
manual and adjust the ear hook to the best fit of your ears.  
I hear but cannot control the music on my device (e.g. skip  
forward/backward).  
Bluetooth audio source does not support AVRCP.  
» Check the user manual of your audio source.  
EN  
9
 
 
Philips Consumer Lifestyle  
HK-1036-SHB6000  
........................................................  
(Report No. / Numéro du Rapport)  
2010  
...........................................................................  
(Year in which the CE mark is affixed / Année au cours  
de laquelle le marquage CE a été apposé)  
EC DECLARATION OF CONFORMITY  
(DECLARATION DE CONFORMITE CE)  
We / Nous, PHILIPS CONSUMER LIFESTYLE B.V.  
(Name / Nom de l’entreprise)  
TUSSENDIEPEN 4, 9206 AD DRACHTEN, THE NETHERLANDS  
(address / adresse)  
Declare under our responsibility that the electrical product(s):  
(Déclarons sous notre propre responsabilité que le(s) produit(s) électrique(s):)  
PHILIPS  
SHB6000; SHB6000/00/10/28  
.......................................................................  
(brand name, nom de la marque)  
...........................................................  
(Type version or model, référence ou modèle)  
Bluetooth Stereo Headset  
..............................................................................................  
(product description, description du produit)  
To which this declaration relates is in conformity with the following harmonized standards:  
(Auquel cette déclaration se rapporte, est conforme aux normes harmonisées suivantes)  
(title, number and date of issue of the standard / titre, numéro et date de parution de la norme)  
EN 300 328 V1.7.1:2006  
EN 301 489-1 V1.8.1:2008; EN 301 489-17 V1.3.2:2008  
EN50371:2002  
EN 60950-1:2006/A11:2009  
Following the provisions of :  
(Conformément aux exigences essentielles et autres dispositions pertinentes de:)  
1999/5/EC (R&TTE Directive) (Directive R&TTE 1999/5/CE)  
And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC  
Permanent Documents  
(Et sont fabriqués conformément à une qualité au moins conforme à la norme ISO 9001 ou aux Documents Permanents CENELEC)  
The Notified Body ...............S..G..S...2..1.5..0............................ performed ......N..o.t.i.fi.e..d..B..o..d.y..O...p.i.n.i.o..n...............  
(L’Organisme Notifié)  
(Name and number/ nom et numéro)  
(a effectué)  
(description of intervention /  
description de l’intervention)  
ZD02H0001  
And issued the certificate, .................................................................  
(et a délivré le certificat)  
(certificate number / numéro du certificat)  
Remarks:  
(Remarques:)  
Drachten, The Netherlands, 08.09.2010  
...........................................................  
(place,date / lieu, date)  
A.Speelman, CL Compliance Manager  
............................................................................................  
(signature, name and function / signature, nom et fonction)  
Philips Consumer Lifystyle  
AMB 544-9056  
 
© 2010 Koninklijke Philips Electronics N.V.  
All rights reserved.  
SHB6000_UM_00_V1.1  
 

Patton electronic Welding System 000CU2 User Manual
Peavey Electronic Keyboard DPM 4 User Manual
Philips Automobile Accessories 12258ECO User Manual
Philips MP3 Player WAC7505 User Manual
Philips Portable Radio AE6565 User Manual
Philips Universal Remote SRU4105WM 17 User Manual
Pioneer Computer Drive DVR 107 User Manual
Pioneer DJ Equipment The Pioneer DJ User Manual
Polycom Telephone DOC2548A User Manual
Prozone Pool Products Air Cleaner Air Purification System User Manual