Perlick Refrigerator R24S User Manual

INSTALLATION AND OPERATION INSTRUCTIONS  
SINGLE DOOR REFRIGERATOR  
MODEL NOS.  
R24N  
R24S  
R24S  
R24N  
IMPORTANT INFORMATION  
Table of Contents  
Cabinet Specifications ..........................................2  
Installing  
This manual has been prepared to assist you in the  
installation of your Single Door Refrigerator and to  
acquaint you with its operation and maintenance.  
Uncrating and Inspection ................................3  
Plumbing .........................................................3  
Electrical..........................................................3  
Installing Shelves ............................................3  
Installing Casters or Legs ...............................3  
Placing The Cabinet........................................3  
Sealing the Floor.............................................4  
Temperature Control .............................................4  
Cleaning................................................................4  
Cleaning Stainless Steel/Avoiding Corrosion .......4  
Replacement Parts ............................................5/6  
Wiring Diagram .....................................................7  
Reversing the Doors .............................................8  
We dedicate considerable time to ensure that our  
products provide the highest level of customer  
satisfaction. If, however service is required, call  
Perlick at 1-800-777-7267 or your dealer who can  
provide you with a list of qualified service agents. For  
your own protection, never return merchandise for  
credit without our approval.  
We thank you for selecting a Perlick product  
and assure you of our continuing interest in  
your satisfaction.  
IMPORTANT WARRANTY INFORMATION  
A Warranty card is enclosed that must be completed  
and mailed to the Perlick Corporation in order to  
register the warranty. If the card is not returned to  
Perlick, the warranty period will begin from the date  
the equipment is shipped from the factory.  
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Form No. Z2288  
Rev. 8.22.06  
 
Preparing the Cabinet – Single Door Refrigerator  
Uncrating and Inspection  
Anti-tip (without Legs or casters)  
Remove all crating material before operating.  
Carefully inspect cabinet for hidden damage.  
If damage is discovered, file your claim immediately  
with the transport company. Perlick is not  
responsible for damage in transit.  
To prevent the cabinet from tipping forward and to  
provide a stable installation, the cabinet must be  
secured in place with an anti-tip device.  
A set of metal anti-tip brackets and installation  
screws (#10-34” wood screws) are supplied. These  
brackets should be attached to the floor, at the  
back of the cabinet; each bracket located to catch  
each rear leveling leg when the cabinet is pushed  
backward into position.  
Plumbing  
No plumbing connections are required. Condensate  
from the cooling coil is automatically evaporated  
through a condensate pan located in the  
condensing unit section.  
THE ANTI-TIP BRACKETS MUST CATCH EACH  
OF THE LEVELING LEGS TO HAVE A STABLE  
AND SAFE INSTALLATION.  
Electrical  
The cabinet must be connected to a separately  
fused power source (see Electrical Specification  
Plate) and grounded in accordance with National  
and Local Electrical Codes.  
CAUTION: Do not attempt to operate the equipment  
on any other power source than that listed on the  
Electrical Specification Plate.  
Some installation sites might need to be modified to  
provide a secure surface for attaching the bracket.  
Refer to the illustration below for anti-tip mounting  
bracket locations.  
Surface  
mounts  
to floor.  
NOTE: Do not extend leveler leg  
more than 3/4out of base. Do not  
shim or pad to obtain levelness.  
Ø 3/8”  
1 1/2”  
Placing the Cabinet  
20 7/8”  
To assure maximum performance, fresh air must  
be allowed to circulate through the machinery  
compartment. Do not place anything in front of the  
cabinet that would obstruct air flow at these grilles.  
Do not place the unit in an unventilated small room.  
Cabinet must  
have at least  
5/16clearance  
from floor to  
accomodate  
brackets.  
7/16”  
Shown with leg  
Cabinet should be leveled front to back and side  
to side.  
leveler engaged  
in anti-tip bracket.  
Installing Casters or Legs (optional)  
Attach casters or legs to the mounting bracket with  
lockwashers and 14”–20 hex head nuts provided.  
Attach bracket and leg/caster assembly to the side  
1
of the cabinet base using the 4”–20 hex head self-  
tapping machine screws provided.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2288  
Rev. 8.22.06  
3
 
Operation Instructions – Single Door Refrigerator  
Sealing the Cabinet  
Temperature Control  
For sanitation purposes, it may be necessary to  
seal the base of the cabinet to the floor. This can be  
accomplished by laying a bead of silicone sealant  
between the base of the cabinet and the floor as  
shown by the figure below.  
An adjustable temperature control is located inside  
the refrigerator on the evaporator fan panel  
assembly. Approximate temperature operating  
range: 32° F. minimum and 42° F.  
maximum. Make adjustments as shown to attain  
the desired  
When sealing the cabinet to the floor, make sure  
that the louvered front grille plate can still be  
removed for condenser maintenance and cleaning.  
temperature.  
Colder Temperatures: Turn the adjusting  
screw clockwise (to the right).  
Warmer Temperatures: Turn the adjusting  
screw counterclockwise (to the left).  
Temperature Control “OFF”: Turn the  
adjusting screw completely counterclock-  
wise to the “O” position until a click is noted.  
CABINET  
The condenser fan and the evaporator fan  
motor turns off and on with the compressor.  
BEAD SILICON  
SEALER (RTV)  
NORMAL  
FLOOR  
Cleaning the Cabinet:  
CONDENSING UNIT  
Use a mild detergent and water to clean the  
inside and outside of the cabinet. Dry  
thoroughly. Never use a scouring pad or  
abrasive cleanser.  
Avoiding Stainless Steel Corrosion  
Corrosion can be prevented by following product  
cautions, cleaning instructions and avoiding use  
of certain chemicals or objects which will cause  
stainless steel corrosion.  
NOTE: An industrial strength, commercial  
cleaner can be used to clean the outside of  
painted cabinets  
STAINLESS STEEL ENEMY  
Steel wool or steel scouring pads  
Cherry/Orange/Olive juice  
Chlorine Bleach  
Cleaning the Condenser:  
Use a long handled, stiff brush to clean dirt  
from the front surface of the condenser.  
Keeping the condenser free from dust and  
dirt will ensure efficient operation.  
Sharp Objects  
CAUTION: Do not bend the fins while  
brushing the front of the condenser..  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2288  
Rev. 8.22.06  
4
 
Replacement Parts – Single Door Refrigerator  
21  
13  
10 11  
19  
14  
17  
16  
15  
12  
6
1
22  
20  
22  
2
3
4
18  
5
23  
9
7
24  
8
CAUTION  
Service should be done by a qualified  
refrigeration technician.  
Disconnect all power before servicing  
the cabinet.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2288  
Rev. 8.22.06  
5
 
Replacement Parts – Single Door Refrigerator  
MODEL NOS.  
ALL MODELS  
Item Description  
Part Numbers  
63778  
1
2
3
Compressor for R134A  
Condenser fan motor  
Condenser fan motor bracket  
Condenser fan blade  
C15239A  
60988-1  
C22370  
65206-2  
65159-1  
65158-1  
65252  
4
5
6
Condenser fan shroud  
Rear panel  
7
Front grille  
8
Condenser coil  
9
Condenser pan  
65473  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
29  
30  
31  
Evaporator fan guard  
Evaporator fan motor  
Evaporator assembly, complete  
Top overlay  
Temperature control with dial plate  
Door assembly  
Magnetic door gasket  
Shelf  
Shelf, bottom  
Pilaster  
Shelf clip  
Evaporator grille  
Tip over bracket  
65254  
65253  
H66136R  
65429-1SS  
61271  
66223  
66237-1  
66236-1  
64809-1  
C19271  
C15875  
66139-2  
63740  
C31409-1  
65423  
65426  
66246L  
66246R  
65531  
65532  
65271  
Door handle  
Leg kit set of 4 includes brackets  
Caster kit set of 4 including brackets (not shown)  
Complete hinge set-left (not shown)  
Complete hinge set-right (not shown)  
Power cord wiring harness (not shown)  
Evaporator assembly wiring harness (not shown)  
Evaporator fan motor wire harness (not shown)  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2288  
Rev. 8.22.06  
6
 
Wiring Diagram – Single Door Refrigerator  
EVAPORATOR FAN  
BLUE  
JUNCTION  
POINTS  
WHITE  
THERMOSTAT  
BLACK  
JUNCTION  
POINTS  
JUNCTION  
POINTS  
BLUE  
WHITE  
RED  
CONDENSER FAN  
COMPRESSOR  
BLACK  
WHITE  
GREEN  
POWER CONNECTION  
NEMA-15P CORD  
RED  
OVERLOAD  
RELAY  
WHITE  
END VIEW  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2288  
Rev. 8.22.06  
7
 
Door Switching Instructions – Single Door Refrigerator  
Tools Required  
STEP 4:  
Remove bottom hinge bracket to  
allow you to remove the door closing  
insert. Immediately replace hinge  
bracket.  
Large Flathead Screwdriver.  
Regular Philips-head screwdriver.  
Small Philips-head screwdriver  
HINGE  
BRACKET  
Left Hinged Door  
Units are available from  
factory mounted left or right.  
Workboard units are avail-  
able with left mounting only.  
All doors may be changed by  
customer.  
CLOSING  
INSERT  
HINGE  
BRACKET  
STEP 5:  
Remove top hinge bracket to allow  
assembly of door closing insert  
removed in step 4. reassemble hinge  
to door after installing the closing  
insert.  
Operations to Perform  
Operation Notes  
NOTE 1:  
NOTE: Changing  
the door mount is  
not advised if you  
have a custom  
wood overlay.  
STEP 1  
NOTE 1  
STEP 2  
STEP 5  
NOTE 4  
This may result in  
having a handle  
in an undesirable  
location.  
Lower left hinge  
bracket rotates  
180° and  
becomes upper  
right hinge  
STEP 4  
STEP 3  
bracket.  
STEP 1:  
NOTE 2 & 3:  
NOTE 2  
NOTE 3  
HINGE PIN  
Remove top hinge pin from assembly.  
Carefully lift and tilt out door assembly  
from the unit and set aside.  
NOTE 5  
STEP 2:  
Top left hinge bracket rotates 180°  
and becomes bottom right hinge  
bracket.  
Bottom hinge pin and door closing  
insert assemble to bottom right hinge  
bracket.  
Carefully remove hole plugs on right  
side of unit. be careful not to  
scratch unit. Top and bottom plugs  
HOLE  
PLUGS  
must be removed. Do not discard.  
DOOR  
HINGE  
HINGE  
NOTE 4: The hole plugs removed  
earlier are to be inserted into the  
vacant left door mounting holes. Do  
not hit with hammer or damage may  
occur. Use hammer handle or wood  
block to push plugs into holes.  
BRACKET  
BRACKET  
CLOSING  
INSERT  
UNIT  
HINGE  
BRACKET  
DOOR  
CLOSING  
INSERT  
BOTTOM  
HINGE PIN  
HINGE  
PIN  
NOTE 5:  
Door bottom on right mounted version was door top on  
left mounted version. Before attempting to re-mount door  
verify that: (1) The door handle will be on the outside of  
door. (2) The door closing inserts are on the bottom. (3)  
All screws are hand tightened, over tightening will dam-  
age the unit.  
STEP 3:  
Remove top and bottom hinge brackets from unit. Then  
remove door closing insert and hinge pin from bottom  
hinge bracket. See door bottom hinge assembly detail.  
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2288  
Rev. 8.22.06  
 

Pelco Home Security System PT1250 EX AMS User Manual
Pelco Switch 100BASE FX User Manual
Philips Coffeemaker HD7850 User Manual
Philips Flat Panel Television Digital TV User Manual
Philips MP3 Docking Station AJ301D 12 User Manual
Planar Computer Monitor PL2010M User Manual
Poulan Chainsaw 1950 1975 2055 2050 2075 2150 2155 2175 2350 2375 2150PR LE Series User Manual
Poulan Snow Blower 430352 User Manual
ProForm Exercise Bike PFEX20020 User Manual
PYLE Audio Music Pedal PPDLUW2 User Manual