Pelco TV Mount PMCL RM15 User Manual

I N S T A L L A T I O N  
PMCL-R Series  
Monitor Mount  
C2220M-A (1/06)  
 
Installation  
The following parts are supplied:  
Qty  
2
Description  
Preassembled rack mounts  
8
Screws, 10-32 x 0.750-inch, Phillips, pan head, black  
Nylon washers  
8
4
Screws, M4 x 0.70 x 6 mm, Phillips, pan head, stainless steel  
Lock washers  
4
1. Tighten the lock nuts (refer to Figure 1) so they are loose enough to allow the brackets to move but tight enough to hold them in place.  
2. Attach the rack mounts to the monitor using the four stainless steel, pan head screws and lock washers. Refer to Figure 1.  
(4) LOCK WASHERS  
(4) SCREWS,  
M4 X 0.70 X 6MM,  
PHILLIPS, PAN HEAD  
(2) LOCK NUTS  
Figure 1. Attaching Rack Mounts to Monitor  
3. Attach the rack mounts to the equipment rack using the eight black, pan head screws and nylon washers. Align the top slots of the mounts  
with mounting holes on the equipment rack that have 0.5-inch spacing below them. All eight mounting slots will align with the holes in the  
rack only if the mounts are in the correct position.  
4. Swivel the monitor forward or backward to position it to the proper viewing angle.  
C2220M-A (1/06)  
3
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted  
pair transmission products.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on Spectra® IV products.  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product when  
returned.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed  
dome products.  
Two years on Spectra III, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair).  
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed  
to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product lia-  
bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such  
Products. In no event will Pelco be liable for any special, incidental or consequential damages  
(including loss of use, loss of profit and claims of third parties) however caused, whether by  
the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
REVISION HISTORY  
Manual #  
C2220M  
C2220M-A  
Date  
11/05  
1/06  
Comments  
Original version.  
Added information about aligning mounting holes properly.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura, ExSite, and Spectra III are trademarks of Pelco.  
© Copyright 2006, Pelco. All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc  
Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com  
USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150  
International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120  
 

Pelco VCR C554M 2 98 User Manual
Pentax Film Camera 928M User Manual
Philips Cassette Player AQ4010 05 User Manual
Philips Digital Photo Frame SPF2307 05 User Manual
Philips Headphones SHS4848 28 User Manual
Philips Music Mixer 67A User Manual
Philips Projection Television 55PP9717 User Manual
Philips Recording Equipment AJ3050 User Manual
Pitco Frialator Cooktop RTE14 User Manual
ProForm Treadmill PFTL71230 User Manual