Pelco Security Camera MCC1370H 2 User Manual

INSTALLATION/OPERATION  
CCC1370H-2, CCC1370H-2X,  
and MCC1370H-2  
®
1/3-Inch CCD Camera  
C1961M-E (8/03)  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should be done only by qualified service and installation personnel.  
2. Installation shall be done in accordance with all local and national electrical and mechanical  
codes utilizing only approved materials.  
3. Use only installation methods and materials capable of supporting four times the maximum  
specified load.  
The product may bear the following marks:  
This symbol indicates that dangerous voltage  
C A U T I O N :  
constituting a risk of electric shock is present  
within this unit.  
R I S K O F E L E C T R I C S H O C K .  
D O N O T O P E N .  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation and  
operation.  
C1961M-E (8/03)  
3
 
REGULATORY NOTICES  
This equipment has been tested and found to comply with the limits of a Class B digital device,  
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However there is no guarantee that the  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try and correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Any changes or modifications not expressly approved by the party responsible for compliance could  
void the users authority to operate the equipment.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device many not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
4
C1961M-E (8/03)  
 
DESCRIPTION  
The CCC1370H-2, CCC1370H-2X, and MCC1370H-2 digital cameras are high resolution, compact  
video cameras that feature a 1/3-inch CCD imager. Each cameras high resolution and high-density  
image sensor ensure a sharp and clear picture over a wide range of conditions.  
MODELS  
CCC1370H-2  
CCC1370H-2X  
MCC1370H-2  
1/3-inch, high resolution, color CCD camera, 24 VAC, 60 Hz, NTSC  
1/3-inch, high resolution, color CCD camera, 24 VAC, 50Hz/12 VDC, PAL  
1/3-inch, high resolution, monochrome CCD camera, 24 VAC, 60 Hz, EIA  
C1961M-E (8/03)  
5
 
LOCATION AND FUNCTION OF PARTS  
Refer to Figure 1.  
Lens Mount  
The camera has a standard CS lens mount but can use a C-mount lens when a C/CS-mount  
adapter is installed between the lens and camera.  
Back Focus Lock Screw  
Loosen to adjust the back focus to match the lens attached to the CS mount. Refer to the  
section on Back Focus Adjustment in this manual.  
Camera Mounts  
Top or bottom mounting. Maximum thread length is 3/16-inch. Attach the camera mount  
adapter to extend thread depth to a standard 1/4-inch.  
Level Adjuster  
Controls the video output level when using a DC-controlled auto iris lens.  
Lens Connector  
Four-pin auto iris drive connector.  
Video Output Connector  
This coaxial connector (BNC type) outputs the video signals.  
Iris Mode Selector Switch  
Switch to VIDEO when an auto iris lens is controlled by a video signal. Switch to DC when  
using a DC voltage drive lens.  
LL ADJ Switches  
Use switches to adjust the vertical phase up or down to eliminate vertical roll when multiple  
cameras are connected to a switching device. Each cameras output is synchronized to the  
frequency of the power supply.  
AGC – Automatic Gain Control  
Automatically adjusts the image to compensate for changes in light levels. The AGC function  
switch can be turned ON/OFF by moving the AGC switch right or left. AGC is factory set to ON.  
ᕍᕠ ESC – Electronic Sensitivity Control  
This function changes the sensitivity of the camera by varying the electronic shutter speed  
according to the amount of incident light. The ESC range is 1:300. To reset the ESC function  
switch, move the ON/OFF switch right or left. The ESC is factory set to the ON position.  
ᕍᕗ BLC – Backlight Compensation  
The backlight compensation function allows fine picture correction to prevent the subject from  
being extremely dark due to strong backlight. The BLC function switch can be turned ON/OFF by  
moving the BLC switch right or left. The BLC is factory set to the OFF position. Set the AGC  
switch to ON when using the BLC function.  
6
C1961M-E (8/03)  
 
ᕍᕘ Eclipser Function (NTSC/EIA Models Only)  
The eclipser function is used with an auto iris lens. When using a CCD imager with an auto iris  
lens in an area with minimal lighting contrasts, the auto iris lens closes, resulting in poor  
picture quality. The eclipser function distorts the signal to the auto iris lens, causing the lens to  
open wider and create sufficient lighting contrasts to prevent the silhouetting of figures. The  
eclipser function switch can be turned ON/OFF by moving the ECLP switch right or left. The  
ECLP is factory set to the OFF position. When the auto iris lens used is equipped with a  
response selector (AVERAGE/PEAK), always set the selector to AVERAGE.  
ᕍᕙ Power Input Terminal  
Three-pin terminal strip, push-in type; 24 VAC for NTSC/EIA models; 24 VAC/12 VDC for PAL  
model.  
ᕍᕚ Eclipser Level Controls (NTSC/EIA Models Only)  
a. Threshold – Sets the level for the brightest part of the picture. Anything brighter than this  
adjustment will be eclipsed.  
b. Eclipse – Sets the brightness of the eclipsed area in the signal that controls the automatic  
iris lens.  
c. Gray – Sets the brightness of the eclipsed area as viewed on a monitor.  
3
10  
9
4
5
6
8
10  
9
4
5
6
8
CAMERA MOUNT  
ADAPTER  
LENS  
VIDEO  
LENS  
ON  
VIDEO  
LEVEL  
LEVEL  
OFF  
AGC  
ESC  
VIDEO DC  
LL  
AGC  
ESC  
BLC  
VIDEO DC  
LL  
BLC  
ECLP  
UP DOWN  
THRE ECLP GRAY  
UP DOWN  
DC 12V  
OFF ON  
24VAC  
GRND  
24VAC  
GND  
1
2
3
11  
12 13  
7
14  
11  
13  
7
TOP/FRONT VIEW  
BACK VIEW  
BACK VIEW  
(NTSC/EIA MODELS)  
(PAL MODEL)  
Figure 1. Location and Function of Parts  
C1961M-E (8/03)  
7
 
CONNECTIONS  
POWER  
To connect to the power supply:  
1. Strip at least .50 inch (13 mm) from the power cord to expose the wires.  
2. Insert the three wires into the holes in the terminal strip until they snap into place.  
3. Confirm that the cord is connected to terminal securely by lightly tugging on the cord.  
If you are wiring more than one camera to the same transformer, connect one side of the trans-  
former to the same terminal on all cameras, and connect the other side of the transformer to the  
remaining terminal on all cameras. Failure to connect all of the cameras the same way will cause  
the cameras to be out of phase with each other and may produce a vertical roll when switching  
between cameras.  
VIDEO  
Connect a video cable to the SIGNAL OUT connector (BNC) on the rear of the camera. Refer to  
Table A for the type of video coaxial cable to use.  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
RG11/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
*Minimum cable requirements:  
75 ohms  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
8
C1961M-E (8/03)  
 
LENS INSTALLATION  
The CCC1370H-2, CCC1370H-2X, and MCC1370H-2 can use fixed, manual, or passive (DC-  
controlled) auto iris lenses. The camera has a standard CS lens mount but can use a C-mount lens  
when a C/CS-mount adapter is installed between lens and camera.  
LENS MOUNTING  
1. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space  
between the lens and the CCD element. If necessary, use clean, compressed air to remove any  
foreign matter.  
2. Aim the camera and focus the lens to the object or area to be observed.  
3. If a manual iris lens is used, adjust the iris for the best picture quality. The largest aperture  
gives the best light sensitivity, the smallest aperture the greatest depth of field.  
AUTO IRIS LENSES  
Passive auto iris lenses are DC-controlled via the 4-pin iris drive connector (type D4-152N) located  
on the back of the camera. Pin connections for the iris drive connector are as follows:  
PIN VIDEO SIGNAL CONTROL  
DC VOLTAGE CONTROL  
Control coil (-)  
1
2
3
4
+9 VDC (40 mA max.)  
+9 VDC (40 mA max.)  
AI - Video  
2
4
1
3
Control coil (+)  
Drive coil (+)  
Drive coil (-)  
GND  
LENS CONNECTOR  
C1961M-E (8/03)  
9
 
BACK FOCUS ADJUSTMENT  
Do not release the back focus locking ring unnecessarily. Back focus adjustment has been set at the  
factory to the standard CS-mount back focus distance. However, once a lens is mounted it may be  
necessary to adjust back focal length to match the lens being used.  
FIXED FOCAL LENGTH LENSES  
1. Mount the lens firmly to the camera.  
2. With the camera operating, position the camera to view an object at least 30 feet (10 m) away.  
3. Set the focus ring to infinity ( ).  
4. Set the lens iris to its widest usable opening.  
5. Adjust the back focus.  
a. Use an Allen wrench to loosen the back focus lock screw at the side of the camera.  
b. Turn the lens mount to obtain the sharpest image on the monitor.  
c. Turn the back focus locking ring clockwise to tighten.  
NOTE: Do not over-tighen the back focus lock screw. Over-tightening the back focus lock screw can  
damage the threads on the mount of the lens.  
MOTORIZED ZOOM LENSES  
1. With the camera operating, position the camera to view an object at least 70 feet (25 m) away.  
2. Set the lens in the following manner:  
a. Set the lens iris to its widest usable opening.  
b. Set the lens focus to the FAR position.  
c. Adjust lens zoom to WIDE angle.  
3. Adjust back focus until the object is in sharpest focus.  
a. Use an Allen wrench to loosen the back focus lock screw at the side of the camera.  
b. Turn the lens mount to obtain the sharpest image on the monitor.  
c. Turn the back focus locking ring clockwise to tighten.  
4. Move lens zoom to TELEPHOTO.  
5. Zoom out all the way while observing the focus on the monitor (known as “tracking”). If the  
image stays in focus throughout the entire zoom range, the back focus is correct. Otherwise,  
repeat the process beginning with step 1.  
10  
C1961M-E (8/03)  
 
CAMERA SYNCHRONIZATION  
The power supply of each camera is set to the same synchronized phase at the factory and usually  
does not need to be readjusted.  
When using more than one camera power supply, a brief vertical roll may occur on the monitor  
each time a camera view is switched. To eliminate vertical roll, adjust the phase control by  
synchronizing, or line locking, the cameras to one another. Use the LL switches on the back of the  
camera to make adjustments.  
It may be necessary to have two people in communication when synchronizing the cameras–one  
person at the camera and another person at the monitor to observe the vertical roll and the effect  
of any adjustments made at the camera.  
To synchronize the cameras do the following:  
1. Choose a camera to which all of the other cameras will be synchronized.  
2. Select a second camera that is out of synchronization with the first camera.  
3. Adjust the camera phase by pressing the LL switches up or down.  
4. Switch the cameras back and forth, observing the roll between the cameras when they are  
switched.  
5. Press the LL switches up or down and observe the roll each time an adjustment is made.  
6. Repeat this process as many times as necessary for each camera in the system.  
C1961M-E (8/03)  
11  
 
ECLIPSER ADJUSTMENT (NTSC/EIA MODELS ONLY)  
The eclipser function is available only on NTSC and EIA models. It is set at the factory and usually  
does not need to be readjusted. However, if fine tuning is necessary, do the following:  
1. Set the DIP switches.  
a. AGC: OFF  
b. ESC: OFF  
c. BLC: OFF  
2. Set the IRIS MODE selector.  
a. Auto iris lens controlled by video signal - VIDEO  
b. Auto iris lens controlled by DC voltage - DC  
3. Set the variable resistors and Eclipse DIP switch.  
a. THRE:  
b. ECLP:  
c. GRAY:  
Counterclockwise  
Mechanical center  
Mechanical center  
d. ECLIPSER DIP: OFF  
4. Set the response selector of the auto iris lens (video type) to AVERAGE. While viewing an  
object, set the video output level of the camera to 0.75 Vp-p (100 IRE) by adjusting the LEVEL  
VR of the auto iris lens.  
5. While viewing a brightly lit object (Refer to Figure 2):  
a. Set ECLIPSER DIP switch to ON.  
b. Adjust THRESHOLD variable resistor by turning it clockwise. Set the video output level to  
clip at 0.8~0.85 Vp-p.  
c. Set gray level to 0.35 Vp-p by turning the GRAY variable resistor clockwise or  
counterclockwise.  
6. While viewing an object in front of a bright background (refer to Figure 3), adjust the ECLP  
variable resistor by turning it clockwise or counterclockwise until the foreground is clear (sharp)  
and the background appears gray.  
GRAY  
BACKGROUND  
GRAY LEVEL  
0.8~0.85 Vp-p  
0.35 VP-P  
v
Figure 2. Gray Level Setting  
Figure 3. Image on Monitor  
12  
C1961M-E (8/03)  
 
SPECIFICATIONS  
GENERAL  
PHYSICAL  
Dimensions:  
2.09 (W) x 2.17 (H) x  
2.21 (D) inches  
CCD Sensor:  
1/3-inch interline  
transfer  
(53 x 55 x 56 mm)  
Picture Elements  
CCC1370H-2,  
Weight (without lens): 0.40 lb (0.20 kg)  
MCC1370H-2:  
768H x 494V  
(approx. 380K)  
ENVIRONMENTAL  
CCC1370H-2X: 752H x 582V  
(approx. 440K)  
Operating  
Temperature:  
14°F to 122°F  
(-10°C to 50°C)  
Sensing Area:  
3/16 x 1/8 - inch  
Storage Temperature: -40°F to 140°F  
(-40°C to 60°C)  
(4.7 mm x 3.5 mm)  
Synchronization System  
Humidity:  
20 to 80%  
CCC1370H-2,  
MCC1370H-2:  
(non-condensing)  
AC line lock  
ELECTRICAL  
Power Requirements  
CCC1370H-2,  
MCC1370H-2:  
CCC1370H-2X: 24 VAC, 50 Hz/12 VDC  
Power Connector:  
CCC1370H-2X: AC line lock/DC  
internal  
Horizontal Resolution  
CCC1370H-2,  
24 VAC, 60 Hz  
CCC1370H-2X: 470 TV lines  
MCC1370H-2:  
Iris Control:  
560 TV lines  
Electronic/passive  
3-pin terminal strip,  
push-in type  
BNC  
4-pin connector  
(miniature square)  
Video Connector:  
Lens Jack:  
Minimum Illumination  
CCC1370H-2,  
CCC1370H-2X: 1.0 lux at f1.2, 75%  
highlight reflectance,  
at 2500°K  
Current Consumption  
CCC1370H-2:  
240 mA  
CCC1370H-2X: 270 mA (24 VAC)/  
390 mA (12 VDC)  
MCC1370H-2:  
MCC1370H-2:  
0.10 lux at f1.2, 75%  
highlight reflectance,  
at 2500°K  
220 mA  
ESC:  
300:1  
MECHANICAL  
Lens Mount:  
Signal-to-Noise Ratio: >48 dB (AGC off)  
C/CS mount (Pelco  
PCMA40 mount  
adapter is needed to  
attach C-mount lens)  
1/4 x 20, top and  
bottom of camera  
housing  
Gain Control:  
Vertical Phase:  
Automatic Gain  
Control:  
Automatic  
+66° +/-90°  
Selectable  
Selectable  
Camera Mount:  
Backlight  
Compensation:  
Scanning System  
CCC1370H-2,  
MCC1370H-2:  
POWER SUPPLIES  
TF2000:  
525 lines,  
2:1 interlace  
20 vA power supply,  
24 VAC  
CCC1370H-2X: 625 lines,  
2:1 interlace  
Signal Processing:  
MCS Series  
Power Supply:  
Power supply for up to  
16 cameras, 24 VAC  
DSP  
Auto Iris Lens Type: DC/video control  
Video Output:  
1Vp-p, 75 ohms  
(Design and product specifications subject to  
change without notice.)  
C1961M-E (8/03)  
13  
 
WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment. Exceptions to this warranty are as noted below:  
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras.  
Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series Camclosure® Camera System.  
Two years on 100/150, 200 and 300 Series Camclosure® Camera Systems.  
Two years on all standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.  
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous motion applications.  
Two years on Esprit and WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under  
this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to  
the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or  
consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or  
otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from  
state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:  
Puerto Rico:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Intermediate Consignee  
American Overseas Air Freight  
320 Beach Road  
Burlingame, CA 94010  
USA  
Ultimate Consignee  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
® Pelco, the Pelco logo, Spectra, Genex, Coaxitron, Intercept, Legacy, Esprit, and Camclosure are registered trademarks of Pelco.  
™ Spectra III and Spectra III SE are trademarks of Pelco.  
© Copyright 2002, Pelco. All rights reserved.  
PELCO  
CCC1370H-2,  
CCC1370H-2X, and  
MCC1370H-2  
Tested to Comply  
with FCC Standards  
FOR HOME OR OFFICE USE  
(CONTROL NO: 1303591011)  
14  
C1961M-E (8/03)  
 
REVISION HISTORY  
Manual #  
C1961M  
Date  
11/99  
3/01  
Comments  
Original version.  
C1961M-A  
C1961M-B  
C1961M-C  
C1961M-D  
C1961M-E  
Add information on model CCC1300H-2X.  
Revised eclipser adjustment instructions.  
Revised for enhanced imager; new model numbers.  
Revised information on model CCC1370H-2X.  
Corrected specification for minimum illumination.  
3/01  
12/01  
12/02  
8/03  
C1961M-E (8/03)  
15  
 
®
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada  
 

Paxar Printer TC6039OH User Manual
Pentair Swimming Pool Filter S8M600 User Manual
Philips DVR VR820 User Manual
Philips Portable DVD Player PET835 00 User Manual
Philips Portable Radio AE6775 01 User Manual
Philips Webcam 26MD357B 37 User Manual
Pioneer Car Stereo System DEH 1590UB User Manual
Pioneer Portable DVD Player AVIC 880DVD User Manual
Polycom Webcam CX5500 User Manual
ProForm Home Gym PFEL49050 User Manual