Pelco Pet Fence eh2400 User Manual

®
EH2400  
Indoor Enclosure  
Installation/  
Operation Manual  
C1468M (7/97)  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120  
 
LIST OF ILLUSTRATIONS  
Figure  
Page  
EH2400 Dimension Drawing ..............................................................7  
1
REVISION HISTORY  
Manual #  
Date  
Comments  
C1468M  
7/97  
Original version.  
Pelco Manual C1468M (7/97)  
iii  
 
(This page intentionally left blank.)  
iv  
Pelco Manual C1468M (7/97)  
 
1.0 GENERAL  
1.1 IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be  
observed.  
1. Installation and servicing should only be done by Qualified Service Personnel  
and conform to all Local codes.  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or  
6P enclosure, it is designed for indoor use only and it must not be installed  
where exposed to rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. After replacement/repair of this unit’s electrical components, conduct a resis-  
tance measurement between line and exposed parts to verify the exposed  
parts have not been connected to line circuitry.  
5. The installation method and materials should be capable of supporting four  
(4) times the weight of the enclosure, pan/tilt, camera and lens combination.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage constituting a  
risk of electric shock is present within this unit.  
This symbol indicates that there are important operating and  
maintenance instructions in the literature accompanying this  
unit.  
CAUTION:  
RISK OF  
ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TO REDUCE THE RISK OF ELECTRICAL SHOCK,  
DO NOT REMOVE COVER. NO USER-  
SERVICEABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information  
in this manual prior to installation and operation.  
Pelco Manual C1468M (7/97)  
1
 
2.0 DESCRIPTION  
The EH2400 medium security camera housing is designed to provide a low cost,  
tamper resistant corner mount for fixed camera applications. The EH2400 may be  
installed flush against a ceiling, or mid-wall, in high ceiling applications, without  
compromising enclosure integrity. The smaller frontal area and reduced overall size  
create an unobtrusive enclosure that is ideal for today’s smaller cameras. The  
EH2400 will accommodate Pelco box cameras with vari-focal lenses that do not  
exceed 8-inches (20.32 cm) in total length. Three conduit knockouts allow wires to  
be delivered from the wall (either side) or ceiling.  
Included in this package:  
1
1
5/32-inch tamper resistant L key (p/n ZTHEXKEY5/32)  
Camera mounting screw, 1/4-20 x .375 phillips pan head  
(p/n ZH1/4-20X.375SPP)  
2
Pelco Manual C1468M (7/97)  
 
3.0 INSTALLATION  
Before mounting the EH2400, make certain that the mounting surface is capable of  
supporting the weight of the enclosure plus camera and lens.  
NOTE: The fasteners required to se-  
cure the EH2400 (minimum 1/4-20  
recommended) are not supplied.  
Determine the location of the enclosure and means of delivering all necessary ca-  
bling before beginning the installation process. Knockouts that will accommodate  
1/2-inch or 3/4-inch conduit have been provided on both wall mounting surfaces  
and the ceiling surface.  
3.1 FLUSH CEILING OR MID-WALL CORNER MOUNT  
To install the EH2400 do the following:  
1. Remove the two (2) tamper resistant screws on the underside of the housing  
(using the hex key included in this package) and separate the cover from the  
mounting bracket. Remove the tilt table assembly.  
2. Remove the appropriate knockout according to your installation and/or con-  
duit connection.  
3. Using the mounting bracket, mark and drill holes in the mounting surface.  
4. If you are using conduit to route cabling to the enclosure, complete that por-  
tion of the installation at this time, including routing all cabling.  
5. Attach the enclosure with the required fasteners.  
6. Mount the camera/lens to the tilt table assembly. Install the completed assem-  
bly onto the mounting bracket.  
7. Make all camera/lens connections and adjust the tilt table assembly and cam-  
era lens as necessary.  
8. Replace the cover. Check that all components clear the cover and that cam-  
era angle and lens adjustments are satisfactory. When all adjustments are  
complete, secure the cover with the provided hex key.  
Pelco Manual C1468M (7/97)  
3
 
4.0 MAINTENANCE  
Clean the window regularly to help maintain picture clarity. Use a soft cloth and a  
mild nonabrasive detergent.  
4
Pelco Manual C1468M (7/97)  
 
5.0 MECHANICAL PARTS LIST  
Item No.  
Qty  
Description  
Part Number  
1
2
1
1
1
2
5
5
1
1
2
2
2
Mounting bracket weld assembly  
Cover weld assembly  
Window  
EH24001001WA  
EH24001000WA  
EH240010000  
3
4
Button head tamper proof screw  
4-40 hex nut, stainless steel  
Flat washer, stainless steel  
Tilt table support leg  
ZH1/4-20Z.50TSS  
ZH4-40NUTSH  
ZH125X312X32S  
DF54001COMP  
DF54002COMP  
ZH1/4-20NUTCH  
ZH1/4LWSSL  
5
6
7
8
Tilt table  
9
1/4-20 hex nut, stainless steel  
1/4" split lock washer, SS  
Fender washer  
10  
11  
ZH255X1.50X62  
Pelco Manual C1468M (7/97)  
5
 
6.0 SPECIFICATIONS  
MECHANICAL  
Camera Mounting: Adjustable tilt table  
Maximum Camera/  
Lens Size:  
Accommodates camera/lens combinations (including BNC  
connector) up to:  
8.0" L x 4.0" W x 4.0" H (20.32 cm x 10.16 cm x 10.16 cm)  
Viewing Window: 3/16" (4.76 mm) thick, optically clear, impact resistant Lexan™  
MR5 coated (UL 94HB rated).  
Window  
Viewing Area:  
4.25" x 2.56" (10.8 cm x 6.50 cm)  
Cable Entry:  
Ø.875-inch or Ø1.125-inch knockout access through rear walls  
and top  
Enclosure  
Mounting:  
Eight (8) Ø.250-inch on protected rear surfaces  
GENERAL  
Construction:  
Finish:  
1/8" aluminum  
Gray polyester powder coat  
See Figure 1  
Dimensions:  
Environment:  
Unit Weight:  
Indoor  
6.4 lbs (2.9 kg)  
Shipping Weight: 9 lbs (4.07 kg)  
6
Pelco Manual C1468M (7/97)  
 
3.75  
(9.53)  
1.50  
(3.81)  
4.00  
(10.16)  
13.00 (33.02)  
10.25 (26.04)  
8.63  
(21.92)  
6.50  
(16.51)  
4.25  
(10.80)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES  
Figure 1. EH2400 Dimension Drawing  
Pelco Manual C1468M (7/97)  
7
 
7.0 WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X,  
CC3751H-2,CC3651H-2X,MC3651H-2,andMC3651H-2Xcameramodels,whichhaveafive-  
year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed  
dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Sixmonthsonallpanandtilts,scannersorpresetlensesusedincontinuousmotionapplications  
(that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.  
AllgoodsrequiringwarrantyrepairshallbesentfreightprepaidtoPelco,Clovis,California.Repairs  
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under  
this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the  
specific use or application made of the Products. Pelco’s liability for any claim, whether based on  
breach of contract, negligence, infringement of any rights of any party or product liability, relating  
totheProductsshallnotexceedthepricepaidbytheDealertoPelcoforsuchProducts. Innoevent  
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss  
of profit and claims of third parties) however caused, whether by the negligence of Pelco or  
otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
Ifawarrantyrepairisrequired, theDealermustcontactPelcoat(800) 289-9100or(559)292-1981  
to obtain a Repair Authorization number (RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty  
conditions stated above, please include a written explanation with the product when returned.  
Methodofreturnshipmentshallbethesameorequaltothemethodbywhichtheitemwasreceived  
by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)  
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,  
and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number  
and freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed  
to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco, the Pelco logo, Camclosure, Esprit,  
Genex, Legacy, and Spectra are registered  
trademarks of Pelco.  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Endura and ExSite are trademarks of Pelco.  
© Copyright 1999, Pelco. All rights reserved.  
8
Pelco Manual C1468M (7/97)  
 

Pelco Stereo Receiver C2900M B User Manual
Philips Clock Radio SA3104 User Manual
Philips Microcassette Recorder 1600 User Manual
Philips MP3 Player WAS6050 05 User Manual
Philips Satellite Radio 32PW9544 User Manual
Philips Universal Remote PM601S User Manual
Plantronics Headphones W445 M User Manual
Plantronics Wireless Office Headset CS510A User Manual
Polaris Offroad Vehicle 340 Edge Touring User Manual
Powermate Portable Generator PM052400001 User Manual