Pelco Landscape Lighting C2433SM A 8 02 User Manual

®
00974  
DF8 Series  
Pendant Dome  
Maintenance/  
Service Manual  
C2433SM-A (8/02)  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s  
instructions.  
6. Do not install near any heat sources, such as radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce heat.  
7. Only use attachments/accessories specified by the manufacturer.  
8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or  
sold with the apparatus. When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
9. Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, the apparatus does not operate  
normally, or the apparatus has been dropped.  
10. To reduce the risk of shock, do not perform any servicing other than that contained in  
the operating instructions unless you are qualified to do so.  
11. The installation method and materials should be capable of supporting four times the  
weight of the unit and equipment.  
12. Only use replacement parts recommended by Pelco.  
13. After replacement/repair of this unit’s electrical components, conduct a resistance  
measurement between line and exposed parts to verify the exposed parts have not  
been connected to line circuitry.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous volt-  
age constituting a risk of electric shock is  
present within this unit.  
C A U T I O N :  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are impor-  
tant operating and maintenance instructions  
in the literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
Pelco Manual C2433SM-A (8/02)  
3
 
DESCRIPTION  
DF8 Series pendant domes are discreet surveillance domes that are designed for indoor or  
outdoor use.  
MODELS  
DF8-PB-0  
Indoor, black, fixed mount pendant dome, black opaque lower dome  
with smoked viewing window (1/2 f-stop of light loss)  
DF8-PB-1  
DF8-PB-2  
DF8-PB-3  
DF8-PG-0  
Same as DF8-PB-0, except clear viewing window (virtually no light loss)  
Same as DF8-PB-0, except chrome lower dome (2 f-stops of light loss)  
Same as DF8-PB-0, except gold lower dome (2 f-stops of light loss)  
Indoor, gray, fixed mount pendant dome, black opaque lower dome  
with smoked viewing window (1/2 f-stop of light loss)  
DF8-PG-1  
DF8-PG-2  
DF8-PG-3  
DF8-PG-E0  
Same as DF8-PG-0, except clear viewing window (virtually no light loss)  
Same as DF8-PG-0, except chrome lower dome (2 f-stops of light loss)  
Same as DF8-PG-0, except gold lower dome (2 f-stops of light loss)  
Outdoor, gray, fixed mount pendant dome, heater and blower, black  
opaque lower dome with smoked viewing window (1/2 f-stop of light loss)  
DF8-PG-E1  
Same as DF8-PG-E0, except clear viewing window (virtually no light loss)  
MAINTENANCE  
Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch  
the surfaces of the dome.  
Exterior Surface – Clean the dome’s exterior surface with a nonabrasive cleaning cloth  
and cleaning agent that is safe for acrylic plastic. Either liquid or spray cleaner/wax suitable  
for fine furniture is acceptable.  
Interior Surface (Except Chrome or Gold) – Clean the same as the exterior surface.  
Interior Surface (Chrome or Gold) – The inside surface of a chrome or gold dome is  
easily scratched. Use the following precautions to maintain the dome’s surface.  
1. Always handle the dome from the outside of its circular flange.  
2. Never touch the coated inside surface. The acid in your fingerprints will eventually  
etch the coating if the fingerprints are not carefully removed according to the recom-  
mended cleaning procedure in item 5.  
3. If dust or other contaminants accumulate on the dome’s interior, remove the debris  
with compressed air. Compressed air cans are available from photographic equipment  
or electronic supply dealers.  
4. If heavy residue accumulates and cannot be removed with air pressure, rinse with  
water and immediately dry with air pressure so that water spots will not remain. Avoid  
wiping the coated surface with direct hand pressure – it will easily abrade unless  
extreme care is taken. Once scratched, the dome cannot be recoated.  
5. If internal wiping is necessary, avoid hand rubbing. Instead, make a wick as follows:  
Use a very soft paper towel. Roll a section into a tightly wound tube. Tear the tube in  
half, and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with  
water. Hold the dome with its opening facing downward and wipe the interior of the  
dome with the wet end of the wick. Use a circular motion, starting from the outside and  
spiraling into the center. Use a new wick for each two passes over the dome.  
4
Pelco Manual C2433SM-A (8/02)  
 
EXPLODED ASSEMBLY DIAGRAMS  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
13  
15  
14  
15  
16  
17  
18  
14  
Figure 1. Exploded Assembly Diagram–DF8 Pendant Models  
Table A. Exploded Assembly Parts List–DF8 Pendant Models  
Item  
Qty  
Description  
Part Number  
1
3
Screw, 6-32 x 5/16", pan head, Phillips, gray, with plastic washer  
(outdoor models only)  
Internal tooth lock washer, #6 (outdoor models only)  
Sun shield (outdoor models only)  
Top mount, black  
Top mount, gray  
Gasket  
Internal tooth lock washer, #8  
Screw, 8-32 x 3/8", pan head, Phillips  
Back box, black  
Back box, gray  
Base plate  
Internal tooth lock washer, #8  
Nut, 8-32  
Tilt table support leg  
Fender washer, 1/4"  
Split lock washer, 1/4"  
Nut, 1/4-20  
Tilt table  
Flat washer, 3/16"  
ZH6-32X.312GRAY  
2
3
4
3
1
1
ZH6LWSIS  
MF02-3020-007  
MF03-7060-174  
MF02-7060-174  
70610012  
5
6
7
8
1
3
3
1
ZH8LWSIS  
ZH8-32X.375SPP  
MF03-3021-005  
MF02-3021-005  
PDF54000COMP  
ZH8LWSIS  
ZH8-32NUTSH  
MF03-3020-002  
ZH25X1.50X625  
ZH1/4LWSSL  
ZH1/420NUTCH  
MF03-3021-003  
ZH260X562X65C  
ZH1/420X.500CH  
9
1
3
3
1
2
3
2
1
1
1
1
10  
11  
12  
13  
14  
15  
16  
17  
18  
NS  
Screw, 1/4-20 x 1/2"  
Trim leash assembly attached to side of back box  
Leash  
7061005  
Internal tooth lock washer, #6  
Nut, 6-32  
Nylon cable clamp (outdoor models only)  
ZH6LWSIS  
ZH6-32NUTSH  
ZH8911  
NS = Not shown  
Pelco Manual C2433SM-A (8/02)  
5
 
2
3
4
5
7
1
6
7
6
01145  
Figure 2. Exploded Assembly Diagram–Heater and Fan Assembly (Outdoor Models Only)  
Table B. Exploded Assembly Parts List–Heater and Fan Assembly (Outdoor Models Only)  
Item  
Qty  
Description  
Part Number  
1
2
3
4
5
6
7
NS  
1
1
2
2
2
7
7
1
Circuit board, fan rectifier  
Spacer, 3/16" diameter x .125", #4  
Fan/heater shroud  
Heater pad, 24 VAC, 15W  
Fan, 12 VDC, .7W, 7 cfm  
Nut, 4-40  
Internal tooth lock washer, #4  
Power/heater circuit board on side of back box  
Includes thermostat  
PCB9000277BASSY  
SPA9015  
MF01-1041-013  
HT01-0321-0202  
ZH65-1240-1044  
ZH4-40NUTSH  
ZH4LWSIS  
PCB9000300ASSY  
On at 40°F (4°C)  
Off at 60°F (16°C)  
Spacer, .250" outside diameter x .125", #6  
Internal tooth lock washer, #6  
Nut, 6-32  
SPA8500  
ZH6LWSIS  
ZH6-32NUTSH  
NS = Not shown  
6
Pelco Manual C2433SM-A (8/02)  
 
1
3
2
4
5
6
7
9
8
10  
01146  
Figure 3. Exploded Assembly Diagram–Pendant Lower Dome  
Table C. Exploded Assembly Parts List–Pendant Lower Dome  
Item  
Qty  
Description  
Part Number  
1
5
5
6
1
Screw, 6-32 x 1/4", pan head, Phillips (indoor models only)  
Screw, 6-32 x 3/8", pan head, Phillips (outdoor models only)  
Internal tooth lock washer, #6  
DF8 Heater Ring Assembly (outdoor models only)  
24 VAC, 60W  
ZH6-32X.250SPP  
ZH6-32X.375SPP  
ZH6LWSIS  
2
3
3023-004A  
Includes thermostat  
On at 70°F (21°C)  
Off at 85°F (29°C)  
4
5
6
7
8
1
1
1
1
2
Screw, 6-32 x 1/4", pan head, Phillips  
Lower dome retainer  
O-ring  
ZH6-32X.250SPP  
MF00-3020-006  
ZH69-0105-2756  
GS01-0002-0430  
ZH6-32X.312GRAY  
Trim ring gasket  
Screw, 6-32 x 5/16", pan head,  
Phillips, gray, with plastic washer  
Trim ring, black  
9
1
1
MF03-3020-010  
MF02-3020-010  
80810015-00  
80810015-01  
80810011-2  
Trim ring, gray  
10  
Acrylic dome, black opaque with smoked viewing window  
Acrylic dome, black opaque with clear viewing window  
Acrylic dome (chrome)  
Acrylic dome (gold)  
80810011-3  
Pelco Manual C2433SM-A (8/02)  
7
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual # Date  
C2433SM 9/01  
C2433SM-A 8/02  
Comments  
Original version.  
Added certifications. Revised Important Safeguards and Warnings.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 2002, Pelco.  
All rights reserved.  
8
Pelco Manual C2433SM-A (8/02)  
 

Philips Hair Clippers QC5055 60 User Manual
Philips Headphones SBCHP430 User Manual
Philips Universal Remote SRU7040 User Manual
Philips VCR VR 617 07 User Manual
Phoenix Gold Car Amplifier SD3001 User Manual
Phoenix Gold Car Amplifier Z2502 User Manual
Pioneer Speaker System SP BS21 LR User Manual
Poulan Trimmer FX25 LE XT250 LE User Manual
Precisionaire Air Cleaner PB1209 User Manual
PVI Industries Universal Remote PV500 9 User Manual