®
EA2010 Post Equalizing
Video Amplifier
Installation/Operation
Manual C630M Rev A (8/90)
1.0 WARNINGS
2.0 SCOPE
Prior to installation and use of this product, the follow-
ing WARNINGS should be observed.
The information contained within this manual covers
the EA2010 Post Equalizing Video Amplifier.
1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.
3.0 DESCRIPTION
The Pelco EA2010 provides a low cost, highly effec-
tive means of maintaining CCTV picture quality in runs
of up to 3000 feet (914.4 m) of RG59 cable.
2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is de-
signed for indoor use only and it must not be in-
stalled where exposed to rain and moisture.
Through panel controls provided for adjustable overall
amplifier flat gain of 1 to +8 dB plus adjustable high
frequency boost of 0 dB to greater than 18 dB at 12
MHz, mainlining full video amplitude, contrast and
detail.
4. Only use replacement parts recommended by
Pelco.
5. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
between line and exposed parts to verify the ex-
posed parts have not been connected to line cir-
cuitry.
The EA2010 features all solid-state circuitry and is sup-
plied with a U.L. Listed wall transformer. Applications
should be for POST-EQUALIZATION only (located
near the monitoring equipment); use as a pre-equalizer
is discouraged.
Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827 • DataFAX (800) 289-9108 or (1-559) 292-0435
International customers call (1-559) 292-1981 or FAX (1-559) 348-1120
5.0 SPECIFICATIONS
MECHANICAL
Output Dynamic
Range:
Up to 2 volts p-p at 50% APL
Up to 1.5 volts p-p at 90% APL
Recessed Screwdriver
Cable Lengths:
Cable Type
RG59
Adjustments:
Gain, HF Boost, LF Boost
Maximum Effective Distance
3,000 feet (914.4 m)
ELECTRICAL
RG6
RG11
RG15
4,500 feet (1,371.6 m)
6,000 feet (1,828.8 m)
8,000 feet (2,438.4 m)
Input Voltage: 120VAC,50/60Hz(230VAC,50Hz
optional)
GENERAL
Power Requirements
for Transformer: 1.5 vA (.125 amp) at 12 ±15% volts
RMS 50/60 Hz from a dedicated,
isolated power supply
Environment:
32° to 120° F (0° to 48.89° C)
0-90% relative humidity
Construction:
Cover:
Chassis:
Panel:
Inputs:
Single BNC internally terminated in
75 ohms
Steel, black polyester powder coat
Steel, zinc plated
Aluminum, black polyester powder
coat with white silkscreen
Outputs:
Gain:
Single BNC source terminated
Adjustable from 1 to +8 dB
Dimensions:
Weight:
See Figure 2
Frequency
Response:
3 lbs (1.35 kg)
Adjustable from flat (±1 dB) at 12
MHz, to greater than 18 dB of boost
at 12 MHz
Shipping
Weight:
4 lbs (1.8 kg)
Figure 2. EA2010 Dimension Drawing
Pelco Manual C630M Rev A (8/90)
3
6.0 WARRANTY AND RETURN
INFORMATION
If a warranty repair is required, the Dealer must contact
Pelco at (800) 289-9100 or (559) 292-1981 to obtain a
Repair Authorization number (RA), and provide the
following information:
WARRANTY
Pelco will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one (1) year after the date
of shipment. Exceptions to this warranty are as noted
below:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order
number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.
•
•
Four (4) years on all standard motorized and fixed
focal length lenses.
Two (2) years on Legacy®, Intercept®, CM8500/
CM9500/CM9750 Matrix and DF8 Fixed Dome
products.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
•
Two (2) years on WW5700 series window wiper
(excluding wiper blades).
Method of return shipment shall be the same or equal
to the method by which the item was received by Pelco.
•
•
Two (2) years on cameras.
RETURNS
Six (6) months on all pan and tilts, scanners or
preset lenses used in continuous motion
applications (e.g., preset scan, tour and auto scan
modes).
In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100or (559)292-1981toobtainanauthorization
number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assignedCA/RAnumberandfreightshouldbeprepaid.
All merchandise returned for credit may be subject to
a 20% restocking and refurbishing charge.
Pelco will warranty all replacement parts and repairs
for 90 days from the date of Pelco shipment. All goods
requiring warranty repair shall be sent freight prepaid
to Pelco, Clovis, California. Repairs made necessary
byreasonofmisuse,alteration,normalwear,oraccident
are not covered under this warranty.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Pelcoassumesnoriskandshallbesubjecttonoliability
for damages or loss resulting from the specific use or
application made of the Products. Pelco’s liability for
any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or
product liability, relating to the Products shall not
exceed the price paid by the Dealer to Pelco for such
Products. In no event will Pelco be liable for any
special,incidentalorconsequentialdamages(including
loss of use, loss of profit and claims of third parties)
however caused, whether by the negligence of Pelco or
otherwise.
Clovis, CA 93612-5699
The above warranty provides the Dealer with specific
legal rights. The Dealer may also have additional
rights, which are subject to variation from state to state.
4
Pelco Manual C630M Rev A (8/90)
|