Pelco Home Security System C1992M A User Manual

®
Installation/Operation  
PMC10A  
High-Resolution Color Monitor  
C1992M-A (12/03)  
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120  
 
DESCRIPTION  
The PMC10A is high-resolution, 10-inch (25.4 cm) color monitor. The unit has a resolution of 350 TV lines  
producing an excellent-quality picture. The monitor's power input of 100-240 VAC, 50/60 Hz, is automati-  
cally detected upon power up. All image adjustment controls are conveniently located on the front panel  
of the monitor.  
[
]
Pelco Manual C1992M-A (12/03)  
3
 
INSTALLATION  
The monitor may be placed on any flat surface (desk or table) or rack-mounted. To rack-mount the moni-  
tor follow the instructions supplied with the rack-mount kit.  
1. Video Cable Connection (Refer to Table A for video coaxial cable requirements.)  
a. Connect the video cable to the BNC video input labeled V1 IN on the back panel of the monitor.  
b. Looping Operation Only - Connect a video cable to the BNC connector labeled V1 OUT.  
2. Impedance Switch Setting  
a. Terminating Operation Only - Set the termination switch to the 75W position.  
b. Looping Operation Only - Set the impedance switch to the Y/C-HI position (looping).  
3. Plug the power cord (provided) into the AC INLET connection on the back panel. Plug the other end  
of the cord into a power receptacle.  
FRONT  
VIDEO S-VIDEO  
VOLUME SHARP  
BRIGHT  
CONT.  
COLOR  
TINT  
BACK  
V1 IN  
AU1 IN  
S-VIDEO IN  
Y/C-HI  
75  
V1-HI  
75  
V1 OUT  
AU1 OUT  
S-VIDEO OUT  
AC INLET  
Figure 1. Model PMC10A, 10-inch Color Monitor, Front and Back Panels  
[
]
4
Pelco Manual C1992M-A (12/03)  
 
OPERATION  
1. Set the video format switch located on the front panel to one of the following settings:  
VIDEO - Composite Video (NTSC) mode  
S-VIDEO - Use if the S-VIDEO input jack on the rear of the monitor is used  
2. Turn the monitor ON. Wait 30 seconds for the picture tube to warm up and the power LED indicator to  
light.  
3. If required adjust the picture using the control knobs on the front panel.  
Front Panel Adjustments  
TINT  
Color phase adjustment. Turn clockwise to increase the greenish tones in the picture.  
Turn counterclockwise to increase the reddish tones in the picture.  
COLOR  
CONT  
Color saturation level. Turn the control knob clockwise to increase the saturation level  
and counterclockwise to decrease the saturation level.  
Contrast adjustment. Proper adjustment will allow maximum gradations between the  
darkest and lightest picture contrast. Turn the control clockwise to increase picture  
contrast and counterclockwise to decrease contrast.  
BRIGHT  
Brightness display adjustment. Turn the control clockwise to increase brightness and  
counterclockwise to decrease brightness.  
SHARP  
Sharpness adjustment. Adjust control knob to obtain the clearest picture.  
VOLUME  
Audio adjustment. Turn the control clockwise to increase volume and counterclockwise  
to decrease volume.  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
[
]
Pelco Manual C1992M-A (12/03)  
5
 
MAINTENANCE  
If the quality of the picture is poor and cannot be improved by making adjustments on the front control  
panel, inspect all system connections and cable runs.  
To reduce the risk of electrical shock, do not remove the cover or the back. No user-serviceable parts are  
inside. Refer servicing to qualified personnel, or contact the Pelco Customer Service Department for as-  
sistance. Refer to the Warranty and Return Information section.  
SPECIFICATIONS  
ELECTRICAL  
Input Voltage  
100-240 VAC, 50/60 Hz, automatic switching  
49 watts  
350 TV lines  
10-inch diagonal  
10%  
Power Consumption  
Horizontal Resolution  
Visual Picture Size  
Sweep Linearity  
Speaker Output  
1.0 watt (-3 dBV)  
GENERAL  
Input/Output  
Video  
1 BNC input, 75 ohms or Hi-Z  
1 looping output  
Audio  
1 RCA input, Hi-Z  
1 looping output  
1 DIN input  
S-Video  
1 looping output  
Steel cabinet  
Black  
10.25 (W) x 10.63 (H) x 11.62 (D) inches  
(26.03 x 27.00 x 29.51 cm)  
19 lb (8.6 kg)  
Construction  
Finish  
Dimensions  
Weight  
ENVIRONMENTAL  
Operating Temperature  
Humidity  
32° to 106°F (0° to 41°C)  
0% to 90%, (non-condensing)  
(Design and product specifications subject to change without notice.)  
[
]
6
Pelco Manual C1992M-A (12/03)  
 
REGULATORY NOTICES  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant  
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that the interference will not occur in a particu-  
lar installation. If this equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try and correct the in-  
terference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Any changes or modifications not expressly approved by the party responsible for compliance could void  
the user ’s authority to operate the equipment.  
[
]
Pelco Manual C1992M-A (12/03)  
7
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models, which have a five-year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and EnduraSeries distributed network-based video  
products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight  
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this  
warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s  
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products  
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state  
to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization  
number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate  
address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2000, Pelco. All rights reserved.  
REVISION HISTORY  
Manual #  
C1992M  
Date  
11/00  
1/01  
Comments  
Original version.  
Revised to include ETL, cETL, and CE certifications and warnings.  
Revised monitor dimensions for height to 10.63 inches (27.00 cm).  
C1992M-A  
12/03  
[
]
8
Pelco Manual C1992M-A (12/03)  
 

Pelco Blower HB6000 220 User Manual
Philips Cassette Player AQ5120 01 User Manual
Philips Stereo Amplifier BGM1012 User Manual
Philips Telephone Xalio 300 User Manual
Philips VCR VCR 462 User Manual
Pioneer Car Stereo System P7200HD User Manual
Pioneer DVD Recorder T502202 User Manual
Pioneer Stereo Receiver AVM P9000 User Manual
Planet Technology Switch GSW 2401 User Manual
Polk Audio Stereo System TL1600 User Manual