Pelco Electronic Keyboard KBD300A User Manual

®
Installation/Operation  
KBD300A  
Universal Keyboard  
C527M-L (3/04)  
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com  
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150  
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120  
 
CONTENTS  
Section  
Page  
IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................... 5  
REGULATORY NOTICES .................................................................................................................................. 6  
DESCRIPTION ................................................................................................................................................. 7  
INSTALLATION – CM6700 MODE .................................................................................................................. 9  
Connecting a Keyboard to the Local Keyboard Port............................................................................. 9  
Connecting Keyboards to the Remote Keyboard(s) Port ...................................................................... 9  
INSTALLATION – CM6800 MODE ................................................................................................................ 11  
Connecting KBD300A Direct-Powered Keyboards ............................................................................. 11  
Connecting KBD300A Remote Keyboards.......................................................................................... 13  
INSTALLATION – CM6700 ASCII MODE ...................................................................................................... 15  
RS-232 Interface (CM6700) ................................................................................................................ 15  
RS-422 Interface (CM6700) ................................................................................................................ 17  
INSTALLATION – CM6800 ASCII MODE ...................................................................................................... 19  
RS-232 Interface (CM6800) ................................................................................................................ 19  
RS-485 Interface (CM6800) ................................................................................................................ 21  
INSTALLATION – DIRECT MODE .................................................................................................................. 24  
Connecting the Keyboard ................................................................................................................... 24  
SWITCH SETTINGS ...................................................................................................................................... 26  
PROGRAMMING AND OPERATION .............................................................................................................. 27  
Scanning Functions ............................................................................................................................ 31  
Programming Limit Stops ................................................................................................................... 32  
Zones .................................................................................................................................................. 33  
SPECIFICATIONS ........................................................................................................................................... 34  
PRODUCT WARRANTY AND RETURN INFORMATION ................................................................................ 39  
Pelco Manual C527M-L (3/04)  
 
[ 3 ]  
List of Illustrations  
Figure  
Page  
1
2
3
4
5
6
7
8
9
Wiring Diagram for Local/Remote Keyboards ................................................................................... 10  
Keyboard Cabling Diagram................................................................................................................. 10  
Data Cables Plugged into COM 5 and 6 (CM6800-48X8 Shown) ...................................................... 12  
Connecting Remote Keyboards (CM6800-48X8 Shown).................................................................... 14  
RS-232 Interface Connections (CM6700) ........................................................................................... 16  
RS-422 Interface Connections (CM6700) ........................................................................................... 18  
RS-232 Interface Connections (CM6800-48X8 Shown) ..................................................................... 20  
RS-485 Interface Connections (CM6800-48X8 Shown) ..................................................................... 22  
COM Port Connections and RJ-45 Connector Pin-Outs ..................................................................... 23  
10 Direct Keyboard and Receiver Wiring ................................................................................................ 25  
11 Keyboard Rear Panel .......................................................................................................................... 27  
12 Keyboard Functions ............................................................................................................................ 30  
List of Tables  
Table  
Page  
A
B
C
D
E
F
G
H
KBD300A Operational Features ........................................................................................................... 8  
Keyboard Addresses........................................................................................................................... 26  
Keyboard Modes ................................................................................................................................ 26  
Keyboard Functions ............................................................................................................................ 27  
KBD300A Button Functions ................................................................................................................ 30  
Operating Scan Functions with Various Receivers ............................................................................ 31  
Limit Set Codes .................................................................................................................................. 32  
Zone Programming Procedure ............................................................................................................ 33  
[ 4 ] Pelco Manual C527M-L (3/04)  
 
IMPORTANT SAFETY INSTRUCTIONS  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
Only use attachments/accessories specified by the manufacturer.  
ᕫᕾ Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
ᕫᕵ Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such  
as vases shall be placed on the apparatus.  
ᕫᕶ WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or  
moisture.  
ᕫᕷ Installation should be done only by qualified personnel and conform to all local codes.  
ᕫᕸ Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is  
designed for indoor use only and it must not be installed where exposed to rain and moisture.  
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk  
of electric shock do not perform any servicing other that contained in the operating instructions unless  
you are qualified to do so.  
Only use replacement parts recommended by Pelco.  
Pelco Manual C527M-L (3/04)  
 
[ 5 ]  
REGULATORY NOTICES  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and (2) this device must accept any interference re-  
ceived, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant  
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However there is no guarantee that the interference will not occur in a particu-  
lar installation. If this equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-  
ference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: How to Identify and Resolve Radio-  
TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington  
D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment  
can void your authority to operate this equipment under Federal Communications Commissions rules.  
[ 6 ] Pelco Manual C527M-L (3/04)  
 
DESCRIPTION  
The KBD300A Universal Keyboard has many operational features (refer to Table A) and can be used in nu-  
merous operational modes:  
CM6700 Mode: Program and operate the CM6700 Matrix Switcher/Controller Unit (SCU). Also control a  
Genex® multiplexer from a CM6700. Multiple keyboards can be used in this mode.  
CM6800 Mode: Program and operate the CM6800 Matrix Switcher/Controller Unit (SCU). Also control a  
Genex multiplexer from a CM6800 SCU. Multiple keyboards can be used in this mode.  
Direct P Mode: Control up to 16 receivers connected directly to the keyboard. A separate system, such  
as an MS500 or VA6100 Switcher, is needed to route video to the monitor.  
NOTE: The KBD300A keyboard can also be used in Direct Mode to program a CM9760-MDA  
Master Distribution Amplifier. Refer to the CM9760-MDA manual for details.  
NOTE: The KBD300A keyboard has an auto-centering joystick. Be certain the joystick remains in  
the neutral (vertical) position as power is applied to the keyboard. Do not move or hold down the  
joystick until after the red digit LEDs have finished flashing the firmware revision.  
The latest firmware release (version 5.00) allows three additional modes:  
CM6700 ASCII Mode: This mode supports the CM6700 matrix auxiliary commands. The F1, F2, and F3  
keys control the CM6700-MXB relays that are on the matrix bay. To enable this mode, DIP switch 7 must  
be ON and DIP switch 8 must be OFF.  
CM6800 ASCII Mode: This mode supports the CM6800 GPI commands. The F1, F2, and F3 keys control  
the relays on an REL2064 that is connected to a CM6800 switcher. To enable this mode, DIP switch 7  
must be ON and DIP switch 8 must be ON.  
Direct D Mode: This mode is similar to the Direct P Protocol, except that the same set of commands is  
now sent in Direct D Protocol. To enable Direct D mode, DIP switches 5 and 7 must be ON.  
NOTE: You must upgrade your KBD firmware to version 5.00 if the application requires you to  
select two-digit monitor numbers.  
Pelco Manual C527M-L (3/04)  
 
[ 7 ]  
Table A. KBD300A Operational Features  
CM6700/ Direct CM6700 CM6800 Direct  
Function  
CM6800  
P*  
Yes  
Yes  
No  
ASCII** ASCII** D**  
Automatically recognize the mode  
Select cameras (control only for Direct Mode)  
Select monitors  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
No  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Control lenses  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Set and call presets/patterns  
Create Zones  
Yes  
Yes  
Control latching receiver auxiliaries  
Control momentary receiver auxiliaries  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Control multiplexer  
Yes  
(main monitor output for CM6700/6800 mode)  
Control Matrix Switcher  
Program Matrix Switcher  
Sequencing  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
No  
Yes  
Yes  
No  
No  
Yes  
No  
Yes  
No  
No  
No  
No  
Yes  
Yes  
No  
No  
Yes  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
No  
Operate frame, auto, and random scans  
Program and operate patterns  
Control CM6700 auxiliaries  
Control CM6800 GPIs  
Yes  
***Firmware version 2.00 and higher  
***Firmware version 5.00 and higher  
[ 8 ] Pelco Manual C527M-L (3/04)  
 
INSTALLATION – CM6700 MODE  
There are two keyboard ports on the CM6700 SCU.  
The LOCAL KEYBOARD port is for connecting a single keyboard within a distance of 25 feet (7.6 meters).  
The REMOTE KEYBOARD(S) port is for connecting additional remote keyboards.  
Connecting a Keyboard to the Local Keyboard Port  
Use the data cable that is supplied with the keyboard. Plug one end of the cable into the RJ-45  
connector on the rear of the keyboard and the other end into the LOCAL KEYBOARD port on the SCU  
(refer to Figure 1). Set the keyboard switches according to the instructions in the Switch Settings sec-  
tion. Go to step 2 to install remote keyboards, or go to step 10.  
Connecting Keyboards to the Remote Keyboard(s) Port  
NOTE: A KBDKIT or KBDKIT-X is required for this application. The KBDKIT consists of two RJ-45  
wall blocks and a 120 VAC to 12 VAC transformer. The KBDKIT-X is for 230 VAC. Use one KBDKIT  
for each keyboard.  
Refer to Figures 1 and 2 for the following steps.  
Decide on a suitable location for each keyboard and wall block. Keyboards must be within 25 feet (7.6  
meters) of the wall block. Wall blocks must be within 6 feet (1.8 m) of the nearest suitable electrical  
outlet. Do not mount the wall block at this time.  
Run wall block interconnect cable (user-supplied) from the SCU to the closest keyboard location, then  
to the next nearest location, and the next, etc.  
Communication to the keyboards is RS-485. Maximum cable distance for RS-485 communication over  
24-gauge wire is 4,000 feet (1,219 m). Pelco recommends using shielded twisted pairs cable that meets  
or exceeds the basic requirements for EIA RS-485 applications.  
Remove the wall block cover and make cable connections at each wall block.  
At each wall block, wire the transformer to pins 3 and 4. Polarity is unimportant.  
Replace the cover on the wall block. Secure the wall block to a suitable surface. A double-sided sticky  
pad is provided to mount the wall block.  
Set the switches for each keyboard according to the instructions in the Switch Settings section.  
Plug in all keyboard data cables.  
Plug the KBDKIT or KBDKIT-X transformer into a suitable outlet.  
ᕫᕾ To initialize the keyboard, wait five seconds after powering-up the CM6700, enter the number for the  
monitor you are viewing (1-4), and press MON. The LED display shows the number entered.  
NOTE: You must re-initialize whenever power is cycled.  
ᕫᕵ Go to the Programming and Operation section and program and test for proper operation.  
Pelco Manual C527M-L (3/04)  
 
[ 9 ]  
KBD  
LOCAL  
KEYBOARD  
LOCAL  
KEYBO ARD  
1
25-FOOT KEYBOARD DATA CABLE  
CM6700  
USER-SUPPLIED CABLE  
ADDITIONAL  
KEYBOARDS  
3
REPLACE  
COVER  
REPLACE  
COVER  
6
6
KBD  
KBD  
7
2
2
7
KBDKIT  
8
8
SET SWITCHES  
25-FOOT KEYBOARD  
DATA CABLE  
25-FOOT KEYBOARD  
DATA CABLE  
REMOTE KEYBOARDS  
01225  
Figure 1. Wiring Diagram for Local/Remote Keyboards  
LOCAL  
RJ-45 WALL BLOCK TERMINALS  
4
3
5
6
2
1
7
8
T+ T-  
R- R+  
4
4
TERMINAL  
TERMINAL  
USER-SUPPLIED CABLE  
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
TX+  
TX+  
TX-  
AC  
TX-  
AC  
5
5
AC  
AC  
GND  
GND  
RX-  
RX-  
RX+  
RX+  
12 VAC  
12 VAC  
9
9
01226  
Figure 2. Keyboard Cabling Diagram  
[ 10 ] Pelco Manual C527M-L (3/04)  
 
INSTALLATION – CM6800 MODE  
You can connect up to eight KBD300A keyboards to any of the following ports:  
For the CM6800-48X8:  
COM 5 (one direct-powered keyboard or up to eight remotely connected keyboards)  
COM 6 (same as COM 5)  
COM 7 (up to eight remotely connected keyboards)  
COM 8 (same as COM 7)  
The total number of KBD300A Series keyboards connected to the CM680-48X8 cannot exceed 16.  
For the CM6800-32X6:  
COM 4 (up to eight remotely connected keyboards)  
COM 5 (one direct-powered keyboard or up to eight remotely connected keyboards)  
The total number of KBD300A Series keyboards connected to the CM6800-32X6 cannot exceed eight.  
Connecting KBD300A Direct-Powered Keyboards  
For direct-powered local keyboards, use COM 5 and 6 (serial ports 5 and 6) for the CM6800-48X8 and use  
COM 5 (serial port 5) for the CM6800-32X6. Each port can power one KBD300A keyboard. A KBDKIT(-X) is  
required if the distance between the CM6800 and the keyboard exceeds 25 feet (7.6 m).  
Refer to Figure 3 (CM6800-48X8 shown).  
Using the 25-foot (7.6 m) straight data cable supplied with the keyboard, plug one end into the RJ-45  
connector on the rear of the keyboard. Plug the other end into either COM 5 or 6 on the CM6800-48X8  
or COM 5 on the CM6800-32X6.  
Set the keyboard switches according to the instructions in the Switch Settings section.  
Go to the next section, Connecting KBD300A Remote Keyboards. Go to step 1 to install remote key-  
boards, or go to step 9.  
Pelco Manual C527M-L (3/04)  
 
[ 11 ]  
MAXIMUM NUMBER OF KEYBOARDS POWERED BY COM 5 & 6: 1 PER PORT  
NOTE: THE TOTAL NUMBER OF KBD300A SERIES  
KEYBOARDS CONNECTED TO THE CM6800 CANNOT EXCEED 16.  
KBDKIT(-X) REQUIRED WHEN WIRING MORE THAN 1 KEYBOARD TO A PORT.  
KBD300A  
KBD300A  
AL AR M  
1
2
3
4
5
6
7
8
C O M  
16  
1
5
C O NTR O L  
PTZ  
2
3
4
6
7
8
A
T
+
T
-
R
R
T
+
T
R
+
R
B
-
-
-
+
3
32  
4
O UT  
3
1
2
C O M  
1
7
8
120/230~  
50/60 HZ  
25 WATTS  
VIDE O O UTPUTS  
CM6800 COM 5 & 6  
RJ-45 PIN-OUTS  
KBD300A  
RJ-45 PIN-OUTS  
1 Rx+  
1 Tx+  
2 Tx-  
2 Rx-  
3 KBD 12V  
4 KBD GROUND  
5 GROUND  
6 NC  
3 12V  
4 12V  
5 GROUND  
6 NC  
7 Tx-  
7 Rx-  
8 Tx+  
8 Rx+  
20108  
Figure 3. Data Cables Plugged into COM 5 and 6 (CM6800-48X8 Shown)  
[ 12 ] Pelco Manual C527M-L (3/04)  
 
Connecting KBD300A Remote Keyboards  
For remote keyboard connections, use COM 5, 6, 7, or 8 for the CM6800-48X8 and COM 4 and 5 for the  
CM6800-32X6. Each port can support up to eight KBD300A keyboards. Do not exceed 16 total keyboards  
for the CM6800-48X8 and eight total keyboards for the CM6800-32X6.  
A KBDKIT or KBDKIT(-X) is required to connect remote keyboards. Each kit contains two RJ-45 wall blocks  
and a transformer. Use one wall block for each keyboard.  
Refer to Figure 4 (CM6800-48X8 shown).  
Pick a suitable location for each keyboard and wall block. Wall blocks must be within 6 feet (1.8 m) of  
a suitable electric outlet. Do not mount the wall blocks yet.  
Connect each keyboard to a wall block, using the supplied keyboard data cable.  
Remove the wall block covers and wire the connections between each wall block. Connect to a final  
wall block (which will be connected to the CM6800).  
Communication to the keyboards is RS-485. Maximum cable distance for RS-485 communication over  
24-gauge wire is 4,000 feet (1,219 m). Pelco recommends using shielded twisted pair cable that  
meets or exceeds the basic requirements for EIA RS-485 applications.  
At each wall block, wire the KBDKIT or KBDKIT(-X) transformer to pins 3 and 4.  
Replace the wall block cover. Secure the wall block to a suitable surface using the double-sided  
sticky pad.  
Set the address switches for each keyboard (refer to the Switch Settings section). (If using COM 7 or  
8, the port settings on the CM6800 must be changed from the default settings. Refer to the CM6800  
manual.)  
Connect the final wall block to COM 5, 6, 7, or 8 on the CM6800-48X8 or COM 4 or 5 for the CM6800-  
32X6 using a straight data cable (supplied with the CM6800).  
Plug the KBDKIT or KBDKIT-X transformers into a suitable outlet.  
To initialize the keyboard, wait five seconds after powering-up the CM6800, enter the number for the  
monitor you are viewing, and press MON. The LED display shows the number entered.  
NOTE: You must re-initialize whenever power is cycled.  
ᕫᕾ Go to the Programming and Operation section and program and test for proper operation.  
Pelco Manual C527M-L (3/04)  
 
[ 13 ]  
MAXIMUM NUMBER OF KEYBOARDS: 8 PER PORT  
NOTE: THE TOTAL NUMBER OF KBD300A SERIES  
KEYBOARDS CONNECTED TO THE CM6800 CANNOT EXCEED 16.  
AL AR M  
CM6800 COM 7 & 8  
RJ-45 PIN-OUTS  
KBD300A  
RJ-45 PIN-OUTS  
1
2
3
4
5
6
7
8
C O M  
16  
1
5
1
2
3
4
5
6
7
8
Rx+  
1
2
3
4
5
6
7
8
Tx+  
C O NTR O L  
Rx-  
Tx-  
PTZ  
2
3
4
6
7
8
12V  
12V  
NC  
NC  
A
T
+
T
-
R
R
T
+
T
R
+
R
B
-
-
-
+
3
32  
4
O UT  
GROUND  
NC  
GROUND  
NC  
F
3
1
2
Tx-  
Tx+  
Rx-  
Rx+  
C O M  
1
7
8
120/230~  
50/60 HZ  
25 WATTS  
VIDE O O UTPUTS  
5
6
4
3
2
1
7
8
4-CONDUCTOR, SHIELDED,  
24-GAUGE, SUCH AS BELDEN  
9843 (USER-SUPPLIED)  
WALL  
BLOCK  
4
3
2
1
5
6
4
3
2
1
5
6
5
6
4
3
2
1
KBDKIT(-X)  
1 REQUIRED  
PER KEYBOARD  
7
8
7
8
7
8
12V  
TRANSFORMER  
KBD300A  
KBD300A  
KBD300A  
Figure 4. Connecting Remote Keyboards (CM6800-48X8 Shown)  
[ 14 ] Pelco Manual C527M-L (3/04)  
 
INSTALLATION – CM6700 ASCII MODE  
One ASCII keyboard can be installed, using either an RS-232 or RS-422 interface. If additional local and  
remote keyboards are used, you should install them according to the instructions in the Installation –  
CM6700 Mode and Installation – CM6800 Mode sections before doing an ASCII installation.  
For installation at a remote location that is served by an RS-232 communications facility (such as via dial-  
up phone lines), use an RS-232 connection at both the KBD keyboard and the matrix switcher. (Refer to  
the RS-232 Interface section below.)  
For installation at a remote location that is served by an RS-422 communications facility (such as direct-wire  
or fiber-optic terminals), use an RS-422 connection at both the KBD keyboard and the matrix switcher.  
(Refer to the RS-422 Interface section.)  
NOTE: A KBDKIT or KBDKIT-X is required to use the keyboard in ASCII Mode. The KBDKIT consists of  
two RJ-45 wall blocks and a 120 VAC to 12 VAC transformer. The KBDKIT-X is for 230 VAC.  
Use one wall block.  
RS-232 Interface (CM6700)  
An RS-232/RS-422 converter and power supply (Pelco part number PV130) are required. They are not in-  
cluded and must be ordered separately.  
Refer to Figure 5.  
Remove the cover from the CM6700 SCU and verify that the DIP switches for COM 2 are set for RS-  
232. Refer to the COM 2 Port section in the CM6700 Installation/Operation Manual for setting the  
switches. Reinstall the cover.  
Use an existing CM6700 keyboard to program the COM 2 communication port. (If there is no other  
keyboard, use the one you are installing. Set all DIP switches OFF and plug the keyboard into the  
Local Keyboard port on the back of the CM6700. Remove when programming is completed.) Refer to  
the Setting COM 2 Communication Parameters section in the CM6700 Installation/Operation Manual  
for programming instructions. Set COM 2 port parameters as follows:  
Baud: 9600, Parity: Odd, Stop Bits: 1  
At the CM6700 SCU, connect the COM 2 RS-232 port to the output of the RS-232 device at the SCU  
side of the transmission link.  
Decide on a suitable location for the keyboard and wall block. The keyboard must be within 25 feet  
(7.6 m) of the wall block. The wall block must be within 6 feet (1.8 m) of the nearest suitable electri-  
cal outlet. Do not mount the wall block at this time.  
Remove the wall block cover and make connections between the wall block and the RS-232/RS-422  
converter.  
Wire the +12 VDC power supply to the converter.  
Connect the RS-232 side of the converter to an RS-232 device that interfaces the transport network.  
At the wall block wire the transformer to pins 3 and 4. Polarity is unimportant.  
Replace the cover on the wall block. A double-sided sticky pad is provided to mount the wall block.  
Secure the wall block to a suitable surface.  
Pelco Manual C527M-L (3/04)  
 
[ 15 ]  
ᕫᕾ Set the keyboard DIP switches for ASCII Mode according to the instructions in the Switch Settings  
section.  
ᕫᕵ Plug in the keyboard data cable.  
ᕫᕶ Plug the +12 VDC power supply into a suitable outlet.  
ᕫᕷ Plug the KBDKIT or KBDKIT-X transformer into a suitable outlet.  
ᕫᕸ Apply power to the CM6700 SCU (if not already powered). To initialize the keyboard, wait five sec-  
onds after power-up, enter the number for the monitor you are viewing (1-4), and press MON. The LED  
display shows the number entered. You can now use the keyboard to perform all normal keyboard  
functions except you cannot program the CM6700.  
ᕫᕹ Go to the Programming and Operation section and program and test for proper operation.  
1
CM6700SCU  
LOCAL  
KEYBOARD  
14  
POWER UP  
SCU  
2
NOTE: A SEPARATE PATH MUST BE PROVIDED  
FOR VIDEO TO THE MONITOR.  
3
CUSTOMER SUPPLIED WIRING.  
50 FEET MAXIMUM DISTANCE.  
RS-232  
SCU COM  
PIN  
(TX+)  
(GND)  
2
RS-232 DEVICE  
KBDKIT  
RJ-45 WALL BLOCK  
TERMINALS  
3
7
9
4
3
2
1
5
12 (RX+)  
9
MAXIMUM DISTANCE  
OF 4,000 FEET. USE  
SHIELDED TWISTED  
PA IRS SUCH AS BELDEN  
9843 OR EQUIVALENT.  
6
REPLACE  
COVER  
9-PIN, MALE  
CONNECTOR  
ON CONVERTER  
7
8
TRANSPORT  
NETWORK  
PV130  
DB9 PINS  
3(TX+)  
2(RX+)  
RS-232/RS-422  
CONVERTER  
TERMINAL  
RD (B)  
RD (A)  
TX+  
TX-  
1
2
3
4
5
6
7
8
KBD300A  
5(GND)  
7
4
5
8
RS-232  
RS-422  
25-FOOT  
KEYBOARD  
TD (A)  
TD (B)  
RX-  
11 101  
SET SWITCHES  
DATA CABLE  
RS-232 DEVICE  
RX+  
ANY RS-232 NETWORK  
WALL BLOCK  
+12 VDC  
GND  
12 VAC  
6
CUSTOMER SUPPLIED WIRING.  
50 FEET MAXIMUM DISTANCE.  
12  
13  
POWER  
SUPPLY  
Figure 5. RS-232 Interface Connections (CM6700)  
[ 16 ] Pelco Manual C527M-L (3/04)  
 
RS-422 Interface (CM6700)  
Refer to Figure 6.  
Remove the cover from the CM6700 SCU and verify that the DIP switches for COM 2 are set for  
RS-422. Refer to the COM 2 Port section in the CM6700 Installation/Operation Manual for setting the  
switches. Reinstall the cover.  
Use an existing CM6700 keyboard to program the COM 2 communication port. (If there is no other  
keyboard, use the one you are installing. Set all DIP switches OFF and plug the keyboard into the Lo-  
cal Keyboard port on the back of the CM6700. Remove when programming is completed.) Refer to the  
Setting COM 2 Communication Parameters section in the CM6700 Installation/Operation Manual for  
programming instructions. Set COM 2 port parameters as follows:  
Baud: 9600, Parity: Odd, Stop Bits: 1  
Decide on a suitable location for the keyboard and wall block. The keyboard must be within 25 feet  
(7.6 meters) of the wall block. The wall block must be within 6 feet (1.8 m) of the nearest suitable  
electrical outlet. Do not mount the wall block at this time.  
Remove the wall block cover and make connections between the wall block and COM 2 of the  
CM6700 SCU.  
At the wall block wire the transformer to pins 3 and 4. Polarity is unimportant.  
Replace the cover on the wall block. A double-sided sticky pad is provided to mount the wall block.  
Secure the wall block to a suitable surface.  
Set the keyboard DIP switches according to the instructions in the Switch Settings section.  
Plug in the keyboard data cable.  
Plug the KBDKIT or KBDKIT-X transformer into a suitable outlet.  
ᕫᕾ Apply power to the CM6700 (if not already powered). To initialize the keyboard, wait five seconds  
after power-up, enter the number for the monitor you are viewing (1-4), and press MON. The LED dis-  
play shows the number entered.  
ᕫᕵ Once you apply power to the keyboard and the CM6700 SCU, you can use the keyboard in the same  
manner as a normal keyboard except that in ASCII Mode you cannot program the CM6700.  
ᕫᕶ Go to the Programming and Operation section and program and test for proper operation.  
Pelco Manual C527M-L (3/04)  
 
[ 17 ]  
NOTE: A SEPARATE PATH MUST BE PROVIDED  
1
CM6700SCU  
FOR VIDEO TO THE MONITOR.  
LOCAL  
KEYBOARD  
KBDKIT  
RJ-45 WALL BLOCK  
10  
TERMINALS  
POWER UP  
SCU  
2
4
3
2
1
5
6
6
REPLACE  
COVER  
7
8
4
TERMINAL  
1
2
3
4
5
6
7
8
KBD300A  
3
MAXIMUM DISTANCE  
OF 4,000 FEET. USE  
SHIELDED TWISTED  
PAIRS SUCH AS BELDEN  
9843 OR EQUIVALENT.  
5
4
25-FOOT  
KEYBOARD  
DATA CABLE  
8
7
SET SWITCHES  
SCU COM  
PIN  
2
TO  
WALL BLOCK  
TERMINAL  
12 VAC  
12 (RX+)  
11 (RX-)  
1
2
7
8
(TX+)  
(TX-)  
(RX-)  
(RX+)  
9
8
7
(TX-)  
(TX+)  
Figure 6. RS-422 Interface Connections (CM6700)  
[ 18 ] Pelco Manual C527M-L (3/04)  
 
INSTALLATION – CM6800 ASCII MODE  
RS-232 Interface (CM6800)  
An RS-232/RS-422 converter and power supply (Pelco part number PV130) are required. They are not  
included and must be ordered separately.  
Refer to Figures 7 (CM6800-48X8 shown) and 9.  
Use an existing CM6800 keyboard to program the COM 1, 2, 7, or 8 communication port for the  
CM6800-48X8 or COM 1 or 2 communication port for the CM6800-32X6. (If there is no other key-  
board, use the one you are installing. Set all DIP switches OFF and plug the keyboard into the Local  
Keyboard port on the back of the CM6800. Remove when programming is complete.)  
Do the following to program the COM port:  
a. Press the PGM key. At the prompt, enter the password (default is 2899100). The CM6800 Main  
Menu appears.  
b. Select PORT. The Set Serial Port screen appears.  
c. Select the number of the desired port.  
d. Set COM port parameters as follows: Device: ASCII, Type: RS-232, Baud: 9600, Parity: Odd, Data  
Bits: 8, Stop Bits: 1.  
e. Select RETURN, and RETURN again.  
At the CM6800, connect the COM 1, 2, 7, or 8 RS-232 port (CM6800-48X8) or COM 1 or 2 RS-232 port  
(CM6800-32X6) to the output of the RS-232 device on the CM6800 side of the transmission link.  
Decide on a suitable location for the keyboard and wall block. The keyboard must be within 25 feet  
(7.6 m) of the wall block. The wall block must be within 6 feet (1.8 m) of the nearest suitable electri-  
cal outlet. Do not mount the wall block yet.  
Remove the wall block cover and make the connections between the wall block and the RS-232/  
RS-422 converter.  
Wire the +12 VDC power supply to the converter.  
Connect the RS-232 side of the converter to an RS-232 device that interfaces the transport network.  
At the wall block, wire the transformer to pins 3 and 4. Polarity is unimportant.  
Replace the cover on the wall block. Use the double-sided sticky pad to mount the wall block to a  
suitable surface.  
ᕫᕾ Set the keyboard DIP switches according to the instructions in the Switch Settings section.  
ᕫᕵ Plug in the keyboard data cable.  
ᕫᕶ Plug the +12 VDC power supply into a suitable outlet.  
ᕫᕷ Plug the KBDKIT or KBDKIT-X transformer into a suitable outlet.  
Pelco Manual C527M-L (3/04)  
 
[ 19 ]  
ᕫᕸ Apply power to the CM6800 (if not already powered). To initialize the keyboard, wait five seconds  
after power-up, enter the number for the monitor you are viewing, and press MON. The LED display  
shows the number entered. You can now use the keyboard to perform all normal keyboard functions,  
except you cannot program the CM6800.  
ᕫᕹ Go to the Programming and Operation section and program and test for proper operation.  
PELCO SWITCHER  
MODEL CM6800  
MAIN MENU  
SET SERIAL PORT 05  
1
2
3
4
5
6
7
8
9
CAMERA  
LOGICAL CAMERA  
MONITOR  
DEVICE:  
TYPE:  
BAUD RATE:  
PARITY:  
DATA BITS:  
STOP BITS:  
ASCII  
RS232  
9600  
ODD  
8
ACCESS  
TIME DATE  
PORT  
&
PRIORITY  
SEQUENCE  
MACRO  
1
10 ALARM CONTACTS  
11 EVENT TIMER  
RETURN  
CM6800  
12 SET AUXILIARY MENU  
13 SET PASSWORD  
14 ABOUT CM6800  
ENGLISH  
RETURN  
AL AR M  
1
2
3
4
5
6
7
8
C O M  
16  
1
5
C O NTR O L  
2
PTZ  
2
3
4
6
7
8
A
T
T
-
R
+
R
T
+
T
R
+
R
B
-
-
-
3
32  
4
COM 1, 2, 7, OR 8  
O UT  
1
F
3
1
2
C O M  
1
7
8
NOTE: SEE FIGURE 11 FOR PIN-OUTS  
120/230~  
50/60 HZ  
25 WATTS  
VIDE O O UTPUTS  
POWER UP SCU  
14  
RS-232  
NOTE: A SEPARATE PATH MUST BE PROVIDED  
FOR VIDEO TO THE MONITOR.  
RS-232 DEVICE  
3
KBDKIT  
CUSTOMER -SUPPLIED WIRING.  
50 FEET MAXIMUM DISTANCE.  
RJ-45 WALL BLOCK  
TERMINALS  
TX  
GND  
RX  
4
3
2
1
5
6
7
8
9
MAXIMUM DISTANCE  
OF 4,000 FEET. USE  
SHIELDED TWISTED  
PAIRS SUCH AS BELDEN  
9843 OR EQUIVALENT.  
PV130  
REPLACE  
COVER  
9-PIN, MALE  
CONNECTOR  
ON CONVERTER  
TRANSPORT  
NETWORK  
DB9 PINS  
RS-232/RS-422  
CONVERTER  
TERMINAL  
3(TX+)  
2(RX+)  
5(GND)  
RD (B)  
RD (A)  
TX+  
TX-  
1
2
3
4
5
6
7
8
KBD300A  
7
4
RS-232  
RS-422  
5
8
25-FOOT  
KEYBOARD  
11 10  
SET  
TD (A)  
TD (B)  
RX-  
DATA CABLE  
RS-232 DEVICE  
RX+  
SWITCHES  
ANY RS-232 NETWORK  
WALL  
BLOCK  
4
+12 VDC  
GND  
6
12 VAC  
CUSTOMER -SUPPLIED WIRING.  
50 FEET MAXIMUM DISTANCE.  
12  
13  
POWER  
SUPPLY  
01235  
Figure 7. RS-232 Interface Connections (CM6800-48X8 Shown)  
[ 20 ] Pelco Manual C527M-L (3/04)  
 
RS-485 Interface (CM6800)  
Refer to Figures 8 (CM6800-48X8 shown) and 9.  
Use an existing CM6800 keyboard to program the COM 4, 7, or 8 communication port (CM6800-48X8)  
or COM 4 communications port (CM6800-32X6). (If there is no other keyboard, use the one you are  
installing. Set all DIP switches OFF and plug the keyboard into the Local Keyboard port on the back of  
the CM6800. Remove when programming is complete.)  
Do the following to program the COM port:  
a. Press the PGM key. At the prompt, enter the password (default is 2899100). The CM6800 Main  
Menu appears.  
b. Select PORT. The Set Serial Port screen appears.  
c. Select the number of the desired port.  
d. Set COM port parameters as follows: Device: ASCII, Type: RS-485, Baud: 9600, Parity: Odd, Data  
Bits: 8, Stop Bits: 1.  
e. Select RETURN, and RETURN again.  
Decide on a suitable location for the keyboard and wall block. The keyboard must be within 25 feet  
(7.6 m) of the wall block. The wall block must be within 6 feet (1.8 m) of the nearest suitable electrical  
outlet. Do not mount the wall block yet.  
Remove the wall block cover and make connections between the wall block and COM 4, 7, or 8 of the  
CM6800-48X8 or COM 4 of the CM6800-32X6.  
At the wall block, wire the transformer to pins 3 and 4. Polarity is unimportant.  
Replace the cover on the wall block. Use the double-sided sticky pad to mount the wall block to a  
suitable surface.  
Set the keyboard DIP switches according to the instructions in the Switch Settings section.  
Plug in the keyboard data cable.  
Plug the KBDKIT or KBDKIT-X transformer into a suitable outlet.  
ᕫᕾ Apply power to the CM6800 (if not already powered). To initialize the keyboard, wait five seconds  
after power-up, enter the number for the monitor you are viewing (1-8), and press MON. The LED  
display shows the number entered. Once you apply power to the keyboard and the CM6800, you can  
use the keyboard in the same way as a normal keyboard except that in ASCII Mode you cannot  
program the CM6800.  
ᕫᕵ Go to the Programming and Operation section and program and test for proper operation.  
Pelco Manual C527M-L (3/04)  
 
[ 21 ]  
PELCO SWITCHER  
MODEL CM6800  
MAIN MENU  
SET SERIAL PORT 05  
1
CAMERA  
2
3
4
5
6
7
8
9
LOGICAL CAMERA  
MONITOR  
DEVICE:  
TYPE:  
BAUD RATE:  
PARITY:  
DATA BITS:  
STOP BITS:  
ASCII  
RS485  
9600  
ODD  
8
ACCESS  
TIME DATE  
PORT  
&
PRIORITY  
SEQUENCE  
MACRO  
1
10 ALARM CONTACTS  
11 EVENT TIMER  
12 SET AUXILIARY MENU  
13 SET PASSWORD  
14 ABOUT CM6800  
CM6800  
1
RETURN  
ENGLISH  
RETURN  
AL AR M  
1
2
3
4
5
6
7
8
C O  
M
16  
10  
POWER UP  
SCU  
1
5
C O NTR O  
L
PTZ  
2
2
3
4
6
7
8
A
T
+
T
-
R
R
T
+
T
R
+
R
B
+
-
-
-
3
32  
4
COM 4, 7, OR 8  
O
UT  
F
3
1
2
C O  
M
1
7
8
120/230~  
50/60 HZ  
25 WATTS  
VIDE O  
O
UTPUTS  
NOTE: A SEPARATE PATH MUST BE PROVIDED  
FOR VIDEO TO THE MONITOR.  
NOTE: SEE FIGURE 11  
FOR PIN-OUTS  
KBDKIT  
RJ-45 WALL BLOCK  
TERMINALS  
4
3
2
1
5
6
7
8
6
4
REPLACE  
COVER  
TERMINAL  
1
2
3
4
5
KBD300A  
3
5
MAXIMUM DISTANCE  
OF 4,000 FEET. USE  
SHIELDED TWISTED  
PAIRS SUCH AS BELDEN  
9843 OR EQUIVALENT.  
4
25-FOOT  
6
7
8
7
8
KEYBOARD  
DATA CABLE  
SET SWITCHES  
WALL BLOCK  
TERMINAL  
12 VAC  
1
2
7
8
(TX+)  
(TX-)  
(RX-)  
(RX+)  
9
01231  
Figure 8. RS-485 Interface Connections (CM6800-48X8 Shown)  
[ 22 ] Pelco Manual C527M-L (3/04)  
 
COM PORTS 7, 8  
RS-485 (PROGRAMMABLE  
TO RS-232)  
PIN 1  
PIN 8  
RS-485 FUNCTION  
RS-232 FUNCTION  
1-----Rx  
1-----Rx+  
2-----Rx-  
3-----NC  
4-----NC  
5-----GROUND  
6-----NC  
2-----NC  
3-----NC  
4-----NC  
5-----GROUND  
6-----NC  
7-----NC  
8-----Tx  
7-----Tx-  
8-----Tx+  
COM PORTS 1, 2  
RS-232  
COM PORT 3  
M, RS-485  
COM PORT 4  
RS-485  
COM PORTS 5, 6  
RS-485  
PIN 1  
PIN 8  
PIN 1  
PIN 8  
PIN 1  
PIN 1  
PIN 8  
PIN 8  
1-----Rx  
1-----MRx+  
2-----MRx-  
3-----NC  
1-----Rx+  
2-----Rx-  
3-----NC  
4-----NC  
5-----GROUND  
6-----NC  
1-----Rx+  
2-----NC  
3-----NC  
4-----NC  
5-----GROUND  
6-----NC  
7-----NC  
8-----Tx  
2-----Rx-  
3-----KBD 12V  
4-----KBD GROUND  
5-----GROUND  
6-----NC  
7-----Tx-  
8-----Tx+  
4-----NC  
5-----GROUND  
6-----NC  
7-----MTx-  
8-----MTx+  
7-----Tx-  
8-----Tx+  
NC = NO CONNECTION  
01232  
Figure 9. COM Port Connections and RJ-45 Connector Pin-Outs  
Pelco Manual C527M-L (3/04)  
 
[ 23 ]  
INSTALLATION – DIRECT MODE  
The keyboard is wired directly to a maximum of 16 receivers. You can communicate using Pelco P Protocol  
or Pelco D Protocol. Direct Mode installation/operation is not the same as CM6700 Mode or CM6800  
Mode installation/operation. A separate system, such as an MS500 or VA6100 switcher, is required for  
routing video to the monitor(s).  
In Direct P and Direct D modes you can now change the zoom speed of a PTZ by entering a number from 1  
to 4 followed by a zoom command. This causes the zoom speed command to be sent.  
NOTE: A KBDKIT or KBDKIT-X is required to use the keyboard in Direct Mode. The KBDKIT consists of  
two RJ-45 wall blocks and a 120 VAC to 12 VAC transformer. The KBDKIT-X is for 230 VAC. Only one wall  
block is required for this application.  
Connecting the Keyboard  
Refer to Figure 10.  
Make sure all receivers are configured to communicate using either Pelco P or Pelco D protocol and  
that each receiver has a unique address. Refer to your receiver manual for switch settings.  
Decide on a suitable location for the keyboard and wall block. The keyboard must be within 25 feet  
(7.6 meters) of the wall block. The wall block must be within 6 feet (1.8 m) of the nearest suitable  
electrical outlet. Do not mount the wall block at this time.  
Remove the cover from the KBDKIT or KBDKIT-X wall block. Connect the transmission wires from the  
receiver (Spectra/Esprit system) to the wall block. Refer to Figure 10 and do the following:  
• Connect RX+ from receiver/driver to TX+ (terminal 1) on the wall block.  
• Connect RX- from receiver/driver to TX- (terminal 2) on the wall block  
NOTE: Communication to the keyboards is RS-422. Maximum cable distance for RS-422 communica-  
tion over 24-gauge wire is 4,000 feet (1,219 m). Pelco recommends using shielded twisted pair cable  
that meets or exceeds the basic requirements for EIA RS-422 applications.  
At the wall block wire the transformer to pins 3 and 4. Polarity is unimportant.  
Replace the cover on the wall block. A double-sided sticky pad is provided to mount the wall block.  
Secure the wall block to a suitable surface.  
Set the keyboard DIP switches according to the instructions in the Switch Settings section.  
Plug in the keyboard data cable.  
Plug the KBDKIT or KBDKIT-X transformer into a suitable outlet. The LED display shows number 1,  
which is the default camera number.  
Go to the Programming and Operation section and program and test for proper operation.  
10  
[ 24 ] Pelco Manual C527M-L (3/04)  
 
CONFIGURE RECEIVERS  
TO RECEIVER(S)  
RX-/RX+  
TWISTED  
PAIR  
KBD300A  
4
3
2
1
5
6
7
TX-  
6
8
TX+  
REPLACE  
COVER  
6
12 VA C  
SET SWITCHES  
9
20110  
25-FOOT KEYBOARD  
DATA CABLE  
KBDKIT OR  
KBDKIT-X  
Figure 10. Direct Keyboard and Receiver Wiring  
Pelco Manual C527M-L (3/04)  
 
[ 25 ]  
SWITCH SETTINGS  
To set the switches on the keyboard (refer to Figure 11):  
Remove the two screws and the DIP switch cover plate from the rear of the keyboard.  
Set the switches:  
• Address (Switches 1-4)  
Position the switches according to Table B. Each keyboard in the system must have a different address,  
including the local keyboard. To make programming easier, address keyboards in ascending order.  
NOTE: CM6700 accepts only eight addresses.  
Table B. Keyboard Addresses  
Keyboard  
Switch Settings  
1
2
3
4
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
• Mode (Switches 5, 7, 8)  
Position the switches according to Table C. Switch 6 enables/disables turbo pan. It can be switched  
while the keyboard is on.  
Table C. Keyboard Modes  
CM6700/CM6800** Direct P** CM6700 ASCII*** CM6800 ASCII*** Direct D*** CM9760-MDA*  
Switch 5  
OFF  
ON or OFF  
OFF  
ON  
ON or OFF  
OFF  
OFF  
ON or OFF  
ON  
OFF  
ON or OFF  
ON  
ON  
ON or OFF  
ON  
ON  
ON or OFF  
OFF  
Switch 6  
Switch 7  
Switch 8  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
****Firmware version 4.00 and higher.  
****Firmware version 4.20 and higher automatically recognizes CM6700/CM6800 and Direct P Mode.  
****Firmware version 5.00 and higher.  
[ 26 ] Pelco Manual C527M-L (3/04)  
 
Replace the cover plate.  
PIN 1  
KBD300 RJ-45  
JACK PINOUTS  
1
3
1
3
2
1
2
3
4
TX+  
5
6
7
8
GND  
TX–  
1
2
3
4
5
6
7
8
12 VAC/DC  
NONPOLAR  
RX–  
RX+  
}
DOWN = ON  
01227  
Figure 11. Keyboard Rear Panel  
PROGRAMMING AND OPERATION  
Table D. Keyboard Functions  
Circled numbers refer to Figure 13.  
Function  
Procedure  
Select Monitor*  
LED display shows monitor number in run mode.  
Enter monitor number ᕫᕹ and press MON ᕫᕻ to select.  
Select Camera  
Enter camera number (1-16) ᕫᕹ and press CAM ᕫᕸ to select.  
NOTE: The CM6700 and CM6800 can be programmed to restrict some moni-  
tors from viewing certain cameras. To display a cameras view on your monitor,  
be sure that your keyboard shows the number of the monitor you are viewing  
and be sure that the CM6700 or CM6800 has not been programmed to restrict  
viewing of that camera.  
Pan/Tilt/Zoom  
Move the joystick until the camera reaches the desired position. To increase  
the speed of movement, move the joystick further from center. Twist the joy-  
stick clockwise to zoom in, counterclockwise to zoom out.  
Lens Control  
Presets  
Focus, iris - Press and hold the appropriate lens control key ᕫᕶ until the  
desired effect is seen.  
Enter preset number (1-66) ᕫᕹ and press PRESET to put camera in preset  
position.  
To program, position camera, enter desired preset number (1-66) ᕫᕹ, and hold  
down PRESET for two seconds.  
In CM6700 and CM6800 modes, a label appears on the monitor. Use F1 and  
F2 to edit the label, then select SET and press ACK ᕫᕺ or tap the joystick  
ᕫᕵ to the right and release.  
*This function is not used in Direct Mode.  
Continued on next page  
Pelco Manual C527M-L (3/04)  
 
[ 27 ]  
Table D. Keyboard Functions (continued)  
Function  
Procedure  
Patterns  
Programming and operation varies with the receiver type.  
Spectra® domes (before version 3.0) can use one long (1 minute) or two  
short (0.5 minute) patterns. Spectra domes (version 3.0), Spectra II™  
domes and Esprit® Integrated Positioning Systems can use one long  
(1.5, 3 or 6 minutes) or two short (0.75, 1.5 or 3 minutes) patterns. (Select pat-  
tern lengths at the positioning systems menu.) Spectra IIIcan use four  
patterns of varying length (all drawing from the same block of memory, which  
is almost infinite).  
To program Spectra and Esprit, select a camera (1-16) ᕫᕹ, select a long  
pattern by holding down PATTERN ᕫᕾ for two seconds, or select short  
pattern 1 or 2 by entering 1 or 2 ᕫᕹ and holding down PATTERN ᕫᕾ for two  
seconds. The monitor will indicate the programming function is active. Move  
the camera position ᕫᕵ as desired for the pattern and press ACK ᕫᕺ to close  
the programming function.  
To run a long pattern, press PATTERN ᕫᕾ. To run a short pattern, enter 1 or 2  
ᕫᕹ and press PATTERN ᕫᕾ. Move the joystick ᕫᕵ or call a preset to stop.  
Direct Mode is the same as above, except:  
Do not program a pattern with turbo pan on (switch 6).  
To program Spectra III, enter 95, and then hold down PRESET for about 5  
seconds until the main menu appears. Use the joystick to position the cursor  
beside Patterns and press IRIS OPEN ᕫᕶ. Position the cursor beside Pattern  
Number and press IRIS OPEN ᕫᕶ. Position the cursor beside Program Pattern  
and press IRIS OPEN ᕫᕶ. Follow the directions displayed on the monitor.  
To run a Spectra III pattern, press the pattern number (1-4) ᕫᕹ and then  
PATTERN ᕫᕾ. Move the joystick ᕫᕵ to stop.  
Sequence*  
Sequence steps through all 16 cameras. Camera number, camera title,  
sequence status, and time/date are shown on the monitor.  
Press PREV 4A to step back one camera. Hold for two seconds for a back-  
ward sequence. Monitor shows B. Press during sequence to speed up. Press  
during a forward sequence to reverse.  
Press NEXT 4B to step forward one camera. Hold for two seconds for a  
forward sequence. Monitor shows F. Press during sequence to speed up.  
Press during a backward sequence to go forward.  
Press HOLD 4C to hold a sequence. Monitor shows H. Press HOLD to  
resume.  
Manually select a camera or press CAM ᕫᕸ to turn off a sequence. Monitor  
shows O.  
Macro Sequence*  
Enter 1 or 2 ᕫᕹ and press MACRO to start a group camera sequence. Monitor  
shows M. Refer to your switcher manual for macro/sequence programming.  
Multiplexer Displays* Press SHIFT . Shift key LED lights. The function keys F1 through F3 and  
the auxilary keys can now be used to display the images from multiple cam-  
eras on the monitor.  
F1/LATCH: Zoom  
F2/OFF:  
PIP display  
F3/MOM: Quad display  
AUX ON: 9-screen display  
AUX OFF: 16-screen display  
[ 28 ] Pelco Manual C527M-L (3/04)  
 
Table D. Keyboard Functions (continued)  
Function  
Procedure  
Auxiliaries/  
Relays  
For the CM6700:  
F1 – F3 control only the auxiliaries built into the CM6700 SCU.  
These outputs can be programmed for momentary, keyed, latched, or alarm op-  
eration. Refer to the CM6700 manual for programming instructions.  
F1/LATCH: Activate/deactivate auxiliary 1 relay.*  
F2/OFF:  
Activate/deactivate switcher auxiliary 2 TTL output.*  
F3/MOM: Activate/deactivate switcher auxiliary 3 TTL output.*  
The AUX ON and AUX OFF keys control the auxiliaries in receivers.  
Enter the auxiliary number and press the AUX ON key to turn on. Hold, and  
then release for momentary functions.  
Enter the auxiliary number and press the AUX OFF key to turn off.  
For the CM6800:  
F1-F3 can address auxiliary functions on the CM6800 and on the REL2064  
(a separate auxiliary relay box) to provide additional auxiliary points.  
F1/LATCH: Enter the auxiliary number and press and release F1 to turn on an  
auxiliary (latching).  
F2/OFF:  
Enter the auxiliary number and press and release F2 to turn off an  
auxiliary (latching).  
F3/MOM: Enter the auxiliary number and press and hold down F3 to turn on  
an auxiliary (momentary). Release F3 to turn off the auxiliary.  
Direct Mode:  
In Direct Mode, F1- F3 have no function. LED shows receiver auxiliary  
number for two seconds after the AUX ON or AUX OFF key is pressed.  
Acknowledge  
Alarm*  
Press ACK ᕫᕺ to acknowledge an alarm (or to halt pattern programming).  
Refer to the CM6700 or CM6800 manual for further information on alarms.  
Program  
(CM6700)  
(CM6800)  
For the CM6700:  
To program the CM6700 switcher, press PGM .  
Follow the programming procedure in the CM6700 manual. LED display ᕡ  
shows P in program mode. To exit, navigate to the RETURN field and press ACK  
ᕫᕺ or tap the joystick ᕫᕵ to the right and release.  
For the CM6800:  
To program the CM6800 switcher, press PGM .  
Follow the programming procedure in the CM6800 manual. To exit, navigate to  
the RETURN field and tap the joystick ᕫᕵ to the right and release. Or, press the  
PGM key to return to the previous screen or menu.  
LED  
Firmware Version  
Clear  
LED shows monitor number (in CM6700 and CM6800 modes) or camera/  
receiver number (in Direct Mode) and P (in Program Mode).  
LED flashes for a few seconds to show firmware version on power up (not  
functional on versions prior to 4.0).  
Press CLEAR ᕫᕷ to cancel a number that has been entered. (CM6700/  
CM6800 modes only.) In Direct Mode, this key erases any numerical entries  
entered and redisplays the current camera number selected.  
Infrared Filter  
(IR Cut Filter)  
This function applies to Spectra® color/black-white model SD5BCBW only.  
a. To turn on the filter; press 8, 8, PRESET .  
b. To turn off the filter, press 8, 9, PRESET .  
Shift*  
Press SHIFT to allow the keyboard to send multiplexer commands.  
*This function is not used in Direct Mode.  
9
Pelco Manual C527M-L (3/04)  
 
[ 29 ]  
2
4B  
3
4C  
4A  
5
1
6
7
17  
8
16  
15  
9
10  
14  
11  
12  
13  
Figure 12. Keyboard Functions  
Table E. KBD300A Button Functions  
Reference Number  
Description  
LED display  
Shift key  
1
2
3
Shift key LED  
4A-C  
Sequence keys: Previous, Next, Hold  
Function keys F1/Latch, F2/Off, F3/Mom control auxiliaries.  
With Shift on they control multiplexer display.  
The AUX ON and AUX OFF keys control receiver auxiliaries.  
With Shift on they control multiplexer display.  
5
6
7
8
9
Program key  
Macro sequence key  
Preset key  
10  
11  
Pattern key  
Joystick  
Focus and iris keys (iris keys can be used to scroll through  
menus on the CM6800 only)  
12  
13  
14  
15  
16  
17  
Clear key  
Camera selection key  
Keypad (numbers 1 through 0)  
Acknowledge key  
Monitor selection key  
[ 30 ] Pelco Manual C527M-L (3/04)  
 
Scanning Functions  
Operation of the scanning functions depends on the kind of receiver or pan/tilt mechanism you have and  
the operating mode of your keyboard (CM6700, CM6800, or Direct Mode).  
There are four types of scanning functions: auto (moves camera back and forth between stops), random  
(moves camera in a random pattern), frame (moves camera back and forth in 10 degree steps), and preset (se-  
quences camera through all programmed presets, pausing between each).  
Operate scans according to Table F.  
Table F. Operating Scan Functions with Various Receivers  
Function  
Receiver  
Model  
Controlling  
Protocol  
Auto  
Scan  
Random  
Scan  
Frame  
Scan  
Stop  
Scan  
Preset  
(2)  
15-bit  
97  
Preset  
(1) (3)  
97  
Preset  
(1)  
All  
Pelco  
96  
Preset  
(standard)  
N/A  
Coaxitron®  
98 Preset  
or  
99 Preset  
(3)  
IRD2024  
ERD2200  
Extended  
Coaxitron  
97  
Preset  
96  
Preset  
N/A  
N/A  
Ext. Coax.,  
Serial Pelco  
P or D  
96  
Preset  
or PTZ  
All Spectra  
All Esprit  
99  
Preset  
97  
Preset  
98  
Preset  
N/A  
N/A  
LRD41C  
(before  
ver. 2.98)  
Ext. Coax.,  
Serial Pelco  
P or D  
99  
Preset  
(1) (3)  
99  
Preset  
(1)  
96  
Preset  
N/A  
LRD41C  
(ver 2.98  
and later)  
Ext. Coax.,  
Serial Pelco  
P or D  
99  
Preset  
(3)  
97  
Preset  
96  
Preset  
N/A  
N/A  
N/A  
ERD97P21-U  
Serial Pelco P  
N/A  
97 Preset  
98 Preset  
96 Preset  
(1) First entry starts random scan, next entry changes to auto scan, etc.  
(2) Enter dwell time (5-64 sec.) and press IRIS CLOSE.  
(3) Changes to random scan after 30 minutes.  
Pelco Manual C527M-L (3/04)  
 
[ 31 ]  
Programming Limit Stops  
Spectra and Esprit can be programmed for scan and manual limit stops.  
Program left limit before programming right limit. Locate camera at desired limit. Enter the set code from  
Table G. Hold the PRESET key for two seconds. In CM6700 and CM6800 modes, a label appears on the  
monitor. Use F1 and F2 to edit the label, then select SET and press ACK or tap the joystick to the right and  
release.  
To cancel all limit stops, enter 95. Hold the preset key for two seconds. Move joystick up or down to move  
the pointer to Other. Press IRIS OPEN. Move the pointer to Limit Stops. Press IRIS OPEN. Move joystick  
right/left to change limit stops to off. Press IRIS OPEN. Move the pointer to EXIT. Press IRIS OPEN. Move  
pointer to exit. Press IRIS OPEN.  
Table G. Limit Set Codes  
Direction  
Left Limit  
Right Limit  
Scan Limit  
Manual Limit  
92  
93  
90  
91  
[ 32 ] Pelco Manual C527M-L (3/04)  
 
Zones  
The Zone function is available on Esprit and Spectra positioning systems when operated through a  
CM6700 or CM6800 switch.* This function puts a label on the screen to identify the viewing area. Zones  
can also be blanked to prevent viewing while the camera is positioned in the zone.  
Up to eight pan (horizontal) zones can be defined (zones are not affected by tilt or zoom). Higher num-  
bered zones take precedence so that if zones overlap, the one with the higher number is in effect. Zone  
programming is outlined in Table H.  
Table H. Zone Programming Procedure  
Step  
Procedure  
1. Set left zone limit.  
a. Use the joystick to position the camera at the start (left limit) of the  
zone.  
2. Access zone  
programming.  
a. Press 8, followed by the zone number N (N = 1 through 8), and then  
the AUX ON key to display the zone menu.  
3. Define a label.  
HINT: To ease  
future title editing,  
start each title with  
a. Use F1 and F2 to find the characters for each position in the label  
(26 upper case letters, 26 lower case letters and 10 numbers).  
b. Pan left/right to move between character positions. Continue  
selecting characters until the title is completed (up to 20 charac-  
ters).  
Z(N), where  
N = zone number.  
c. Move down to the SET field and press ACK or tap the joystick to the  
right and release.  
4. Set right zone limit.  
a. Position camera at the right limit of the zone.  
b. Press 8, followed by the zone number, and then the AUX OFF key.  
c. To view zone titles go to step 6.  
5. Clear zones.  
a. Press 8, followed by the zone number, and then the AUX ON key.  
b. Move down to the SET field and Press ACK.  
NOTE: DO NOT pan right.  
c. Press 8, followed by the zone number, and then the AUX OFF key.  
6. Turn on zone labeling.  
7. Turn off zone labeling.  
8. Blank zones.  
a. Press 9, 1, the AUX ON key.  
a. Press 9, 2, the AUX ON key.  
a. Press 9, 5 and hold Preset for about 2 seconds to display the Edit  
Preset 95 menu.  
b. Move down to the SET field and press ACK to display the Camera  
menu.  
c. Move down to the <Alarms, Zone Blank> field and press Iris Open to  
display the Alarms, Zone Blank menu.  
d. Move down to the <Zone Blank> field and press Iris Open to display  
the Zone Blank menu.  
e. Move down to the zone number you wish to blank and press Iris  
Open to move the cursor arrow to the zone blanking status value.  
f. Pan up to turn blanking on, pan down to turn blanking off.  
g. Press Iris Open to accept new status; press Iris Close to cancel.  
h. Repeat steps 8e through 8g for each zone you wish to change, and  
then go to step 8i.  
i. Move down to Exit and press Iris Open repeatedly to move up  
through the menus and return to the normal display.  
*Zones cannot be used in Direct P or Direct D mode.  
Pelco Manual C527M-L (3/04)  
 
[ 33 ]  
SPECIFICATIONS  
GENERAL  
Keyboard Keypad: Electromechanical  
Joystick:  
3-axis, vector-solving, with twisting, return-to-center head  
Red LED, 7-segment, 2 cells  
Digital Display:  
Shift Mode Indicator: Green LED  
Ambient Operating  
Temperature:  
Humidity:  
Dimensions:  
Weight:  
20° to 120°F (-7° to 49°C)  
10–90% non-condensing  
9.50 (W) x 7.125 (D) x 2.25 (H) inches (24.13 x 18.1 x 5.72 cm)  
2.5 lb (1.12 kg)  
Ratings:  
Meets NEMA Type 1 standards  
Meets IP 30 standards  
ELECTRICAL  
Input Voltage:  
12 VAC or ±12 VDC  
5 watts  
Power Consumption:  
Connector Type:  
RJ-45, 8-pin, modular (female)  
Keyboard Communication  
CM6700/CM6800 Mode  
Interface:  
Protocol:  
Baud:  
RS-485  
Pelco ASCII  
9600  
Communication  
Parameters:  
8 data bits, 1 stop bit, odd parity  
CM6700 ASCII Mode  
Interface:  
Protocol:  
RS-422  
Pelco ASCII  
9600  
Baud:  
Communication  
Parameters:  
8 data bits, 1 stop bit, odd parity  
[ 34 ] Pelco Manual C527M-L (3/04)  
 
CM6800 ASCII Mode  
Interface:  
Protocol:  
RS-485  
Pelco ASCII  
9600  
Baud:  
Communication  
Parameters:  
8 data bits, 1 stop bit, odd parity  
Direct P Mode  
Interface:  
Protocol:  
RS-485  
Pelco P  
4800  
Baud:  
Communication  
Parameters:  
8 data bits, 1 stop bit, no parity  
Direct D Mode  
Interface:  
Protocol:  
RS-485  
Pelco D  
2400  
Baud:  
Communication  
Parameters:  
8 data bits, 1 stop bit, no parity  
(Design and product specifications subject to change without notice.)  
This equipment contains electrical or electronic components that must be recycled properly to comply  
with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and  
electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
Pelco Manual C527M-L (3/04)  
 
[ 35 ]  
[ 36 ] Pelco Manual C527M-L (3/04)  
 
REVISION HISTORY  
Manual # Date  
Comments  
C527M  
11/97  
1/98  
Original version.  
C527M-A  
Revised manual to include Direct Mode Installation/Operation instructions. Added CM6700  
Operations instructions.  
C527M-B  
4/98  
Revised installation instructions as a result of hardware changes to the rear panel of the  
CM6700 SCU.  
6/98  
9/98  
4/99  
Added Section 1.2, Regulatory Notices, and Section 1.3, Certifications.  
Revised manual to show new DIP switch and switch settings.  
Added references to Service Bulletin 981014 for connection instructions. Revised material  
in the sections on programming and operating a camera pattern. Revised manual to new  
format.  
C527M-C  
C527M-D  
6/99  
3/00  
Revised the sequence key definitions. Added material on programming Spectra® features to  
the Direct Mode Operation section.  
C527M-E  
Added pattern programming and operation in Direct Mode Operation section to support  
revision 4.0 firmware. Added CM9760-MDA mode.  
C527M-F  
C527M-G  
7/00  
10/01  
Revised format.  
Added information about the CM6800 Matrix Switcher and additional functionality of the  
iris keys and joystick.  
C527M-H  
2/02  
Changed to KBD300A. Revised keyboard drawings to reflect key labeling changes.  
Several procedures revised because of the labeling change. Revised pattern programming  
in Table D to include procedures for Spectra III. Stated that firmware versions 4.20 and  
higher automatically recognize CM6700/6800 and Direct modes.  
Added firmware version 5.00 information as per ECO 02-8447. Added three modes to the  
Description and Installation sections. Revised Tables A, C, and D. Updated Specifications.  
Revised Tables A and D. Removed RS-232 from Specifications.  
Added UL certification seal, changed power specification, and corrected zone information.  
Revised directions for direct mode installation. Revised safety instructions. Changed FCC  
notice. Removed references to use 18-gauge wire for EIA RS-485 communication.  
C527M-I  
11/02  
C527M-J  
C527M-K  
C527M-L  
12/02  
9/03  
3/04  
Pelco Manual C527M-L (3/04)  
 
[ 37 ]  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one  
year after the date of shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X,  
MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and EnduraSeries  
distributed network-based video products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour  
and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty  
repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal  
wear, or accident are not covered under this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made  
of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of  
any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products.  
In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and  
claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject  
to variation from state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair  
Authorization number (RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please  
include a written explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981  
to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.  
Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you  
may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 2004, Pelco. All rights reserved.  
[ 39 ] Pelco Manual C527M-L (3/04)  
Pelco Manual C527M-L (3/04)  
[ 39 ]  
 
®
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Philips Cell Phone CT0699SLV User Manual
Philips Computer Monitor MWB1225I User Manual
Philips Flat Panel Television 14PT2666 01 User Manual
Philips Stereo System MX960D User Manual
Philips Universal Remote SRU3004WM User Manual
Philips VCR VR400 User Manual
Pioneer Car Stereo System DEH P610BT User Manual
Polaris Automobile RANGER XP 4X4 700 EFI User Manual
Polycom Webcam VSX Series User Manual
PYLE Audio Portable Speaker PADH1079 User Manual